意味 | 例文 (285件) |
最小すきまの英語
追加できません
(登録数上限)
英訳・英語 minimum clearance
「最小すきま」の部分一致の例文検索結果
該当件数 : 285件
燃料噴射弁、及び最小隙間決定方法例文帳に追加
FUEL INJECTION VALVE AND METHOD FOR DETERMINING MINIMUM GAP - 特許庁
最適最小隙間演算部14は、求めた分散または偏差を用いて設計仕様値に対しての要求品質を満足する隙間値を逆算し、最適な最小の隙間値である最適最小隙間値を算出する。例文帳に追加
An optimal minimum gap operating part 14 uses the calculated distribution or deviation to inversely calculate a gap value that satisfies requested quality for a design specification value and calculates an optimal minimum gap value being a gap value that is optimal and minimum. - 特許庁
さらに 、画像コマと画像コマの間の隙間が最小となる露光パターンで露光すれば、感光材のロスを最小とすることができる。例文帳に追加
Furthermore, the loss of the photosensitive material is made minimum by performing exposure by an exposure pattern by which a gap between the image frames becomes minimum. - 特許庁
コストアップを最小限に抑え、原稿圧板と操作部の隙間も最小限にして、原稿圧板と操作部の干渉を回避する。例文帳に追加
To minimize a cost increase, to minimize a clearance gap between a manuscript pressure plate and an operating part, and to prevent intervention by the manuscript pressure plate and the operating part. - 特許庁
最小値最大値判定器21でベクトルギャザー命令又はベクトルスキャッター命令に対するアドレスの依存元命令を実行する固定小数点演算器12の演算結果を用いてベクトル要素の最小値及び最大値を判定する最小値最大値判定し、この最小値及び最大値を最小値/最大値レジスタ部31に保持しておく。例文帳に追加
Minimum/maximum value determiner 21 determines minimum/maximum values among vector elements by use of a calculation result of a fixed-point calculation unit 12 for executing an address dependency source instruction in accordance with a vector gather or vector scatter instruction, and holds the minimum/maximum value in a minimum/maximum value register part 31. - 特許庁
圧縮行程の最後で隙間を最小限に抑える圧縮機用ピストンを提供する。例文帳に追加
To provide a compressor piston minimizing a clearance at the end of a compression stroke. - 特許庁
-
履歴機能過去に調べた
単語を確認! -
語彙力診断診断回数が
増える! -
マイ単語帳便利な
学習機能付き! -
マイ例文帳文章で
単語を理解!
「最小すきま」の部分一致の例文検索結果
該当件数 : 285件
間隙寸法Xと最小隙間寸法Yとの間にはX<Yの関係が成立する。例文帳に追加
The following relationship is established between a space dimension X and a minimum space dimension Y; X<Y. - 特許庁
円板状プレートの孔側歯とボス部の軸側歯との隙間を最小限にする。例文帳に追加
To minimize clearance between a hole side tooth of a disc plate and a shaft side tooth of a boss part. - 特許庁
表面に凹凸のある化粧パネルの縁部とフレームとの間の隙間を最小限にする。例文帳に追加
To minimize a clearance between a frame and the edge part of a decorative panel with an uneven surface. - 特許庁
これにより、シートバック4と荷室フロア1a端との隙間を最小限に抑えられる。例文帳に追加
Gap between a backrest 4 and an end of luggage space floor 1a can thus be minimized. - 特許庁
さらに、この最小実行単位が終了するごとに、次の最小実行単位にかかる時間と、割り込みまでの残り時間を比較し、残り時間が十分なら、次の最小実行単位の処理へ進み、残り時間が不足しているなら、空プロセス9を実行する。例文帳に追加
Furthermore, each time the minimum execution unit ends, time to be spent on the next minimum execution unit is compared with the residual time until interrupt, and when there is a plenty of residual time, the processing of the next minimum execution unit starts, and when the residual time is insufficient, the empty process 9 is executed. - 特許庁
ブレード130がシュラウド150の開口部154に対して相対移動する方向(車両上下方向)と最小隙間方向とを異ならせることで、最小隙間(チップクリアランスを小さく設定することが可能となる。例文帳に追加
Since a direction (vehicle vertical direction) in which blades 130 are relatively displaced with respect to an opening 154 of the shroud 150 is made different from a minimum clearance direction, a small clearance (tip clearance) can be set small. - 特許庁
吸入接続管の板厚tと吸入口の径φDの比を4%以上5%以下とすることにより、内部応力を最小限にしかつ冷媒ガスの隙間洩れ量を最小にする。例文帳に追加
A ratio between a plate thickness t of the inlet connection pipe and a diameter ϕD of the inlet is set between 4% and 5% so that the internal stress is minimized and a clearance leakage amount of refrigerant gas is minimized. - 特許庁
接着は作業性がよく、スペーサも最小限なものでよいため、補修面とFRP板1の隙間も最小限に抑えることができ、流水面積の減少も少ない。例文帳に追加
Since bonding has excellent workability and the minimum spacer may be used, the opening between the repair surface and the FRP board 1 can be inhibited minimally, and the decrease of the area of flowing water is also reduced. - 特許庁
|
意味 | 例文 (285件) |
|
ピン留めアイコンをクリックすると単語とその意味を画面の右側に残しておくことができます。 |
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |
weblioのその他のサービス
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |