検定公差の英語

二　その器差が経済産業省令で定める検定公差を超えないこと。例文帳に追加

(ii) The instrumental error does not exceed the verification tolerance specified by the Ordinance the Ministry of Economy, Trade and Industry.発音を聞く  - 日本法令外国語訳データベースシステム

二　その器差が国土交通省令で定める検定公差を超えないこと。例文帳に追加

(ii) The instrumental errors of meteorological instruments do not exceed the respective verification tolerances specified by Ordinance of the Ministry of Land, Infrastructure, Transport and Tourism.発音を聞く  - 日本法令外国語訳データベースシステム

瞬時にガス流量を判定でき、しかも検出されたガス流量が電子式積算値カウンタ１２にダイレクトに供給されるので、積算値の算出をガスメータの検定公差内の誤差で正確に行なうことができる。例文帳に追加

The gas flow rate is determined in a moment, and the integration value is calculated accurately with the error within the calibration tolerance of the gas meter, because the detected gas flow rate is supplied directly to the electronic integration value counter 12. - 特許庁

ガス流量の流量区分毎の積算値を、ガスメータの検定公差内の誤差で算出可能なガス流量の積算装置を提案すること。例文帳に追加

To provide an integrator for a gas flow rate capable of calculating an integration value in each flow rate division of the gas flow rate with an error within a calibration tolerance of a gas meter. - 特許庁

第九十五条　指定製造事業者は、その指定に係る工場又は事業場において、第七十六条第一項の承認に係る型式に属する特定計量器を製造するときは、当該特定計量器が第七十一条第一項第一号の経済産業省令で定める技術上の基準であって同条第二項の経済産業省令で定めるものに適合し、かつ、その器差が同条第一項第二号の経済産業省令で定める検定公差を超えないようにしなければならない。ただし、輸出のため当該特定計量器を製造する場合においてあらかじめ都道府県知事に届け出たとき、及び試験的に当該特定計量器を製造する場合は、この限りでない。例文帳に追加

Article 95 (1) A designated manufacturing business operator shall, in manufacturing specified measuring instruments belonging to the type pertaining to an approval set forth in Article 76, paragraph 1 in its factory or workplace pertaining to the designation, make said specified measuring instruments conform to technical standards specified by the Ordinance of the Ministry of Economy, Trade and Industry set forth in Article 71, paragraph 1, item 1 that fall under the technical standards specified by the Ordinance of the Ministry of Economy, Trade and Industry set forth in paragraph 2 of the same Article and shall make their instrumental error not exceed the verification tolerance specified by the Ordinance of the Ministry of Economy, Trade and Industry set forth in paragraph 1, item 2 of the same Article; provided, however, that this shall not apply to the case where the designated manufacturing business operator manufactures said specified measuring instruments for the purpose of export and has notified the prefectural governor thereof in advance, or where the notifying manufacturing business operator manufactures said specified measuring instruments on a pilot production basis.発音を聞く  - 日本法令外国語訳データベースシステム

２　第十六条第一項第二号ロの指定を受けた外国製造事業者（以下「指定外国製造事業者」という。）は、その指定に係る工場又は事業場において、第八十九条第一項の承認を受けた型式に属する特定計量器で本邦に輸出されるものを製造するときは、当該特定計量器が第七十一条第一項第一号の経済産業省令で定める技術上の基準であって同条第二項の経済産業省令で定めるものに適合し、かつ、その器差が同条第一項第二号の経済産業省令で定める検定公差を超えないようにしなければならない。例文帳に追加

(2) When a foreign manufacturing business operator who has received a designation set forth in Article 16, paragraph 1, item 2 (b) (hereinafter referred to as a "designated foreign manufacturing business operator") manufactures specified measuring instruments belonging to the type for which an approval set forth in Article 89, paragraph 1 was received, in its factory or workplace pertaining to the designation, the designated foreign manufacturing business operator shall make the specified measuring instruments conform to technical standards specified by the Ordinance of the Ministry of Economy, Trade and Industry set forth in Article 71, paragraph 1, item 1 that fall under the technical standards specified by the Ordinance of the Ministry of Economy, Trade and Industry set forth in paragraph 2 of the same Article and shall make their instrumental error not to exceed the verification tolerance specified by the Ordinance of the Ministry of Economy, Trade and Industry set forth in paragraph 1, item 2 of the said Article.発音を聞く  - 日本法令外国語訳データベースシステム

第四十九条　検定証印等、第七十四条第二項若しくは第三項の合番号又は第七十五条第二項の装置検査証印が付されている特定計量器の改造（第二条第五項の経済産業省令で定める改造に限る。次項において同じ。）又は修理をした者は、これらの検定証印等、合番号又は装置検査証印を除去しなければならない。ただし、届出製造事業者若しくは届出修理事業者が当該特定計量器について、又は第百二十七条第一項の指定を受けた者がその指定に係る事業所において使用する特定計量器について、経済産業省令で定める修理をした場合において、その修理をした特定計量器の性能が経済産業省令で定める技術上の基準に適合し、かつ、その器差が経済産業省令で定める使用公差を超えないときは、この限りでない。例文帳に追加

Article 49 (1) Any person who has performed a alteration (limited to the kind of alterations specified by the Ordinance of the Ministry of Economy, Trade and Industry set forth in Article 2, paragraph 5; the same shall apply in the next paragraph.) or a repair of a specified measuring instrument affixed with a verification mark, etc. matching number set forth in Article 74, paragraph 2 or 3, or fitting inspection mark set forth in Article 75, paragraph 2 shall remove such a verification mark, etc., matching number or fitting inspection mark; provided, however, that this shall not apply to the case where a notifying manufacturing business operator or notifying repair business operator has performed a repair of said specified measuring instrument, or where a person who has obtained a designation set forth in Article 127, paragraph 1 has performed a repair specified by the Ordinance of the Ministry of Economy, Trade and Industry of a specified measuring instrument used at his/her place of business pertaining to the designation, if the performance of such a repaired specified measuring instrument conforms to the technical standards specified by the Ordinance of the Ministry of Economy, Trade and Industry and the instrumental error of such a repaired specified measuring instrument does not exceed the tolerance for use specified by the Ordinance of the Ministry of Economy, Trade and Industry.発音を聞く  - 日本法令外国語訳データベースシステム