縁切型の英語

切換開閉器部の絶縁駆動軸部分の絶縁耐圧の向上を図り、さらに絶縁信頼性のある環境適合型の負荷時タップ切換器を得る。例文帳に追加

To provide an environment adaptive type on-load tap switching device which is improved in dielectric strength voltage of an insulated drive shaft portion of a selector switch portion, and further has insulation reliability. - 特許庁

スローアウエイ型切削工具の各切れ刃縁３に沿って、導電性材料よりなり且つ切れ刃縁から一定幅で略水平に延びるセンサ薄膜８あるいは切れ刃縁から一定距離離れた位置に略水平に延びる細線状のセンサ薄膜８を１本形成する。例文帳に追加

One each of sensor thin films 8 which are made out of conductive material while being almost horizontally extended by a definite width from a cutting blade edge along each cutting blade edge 3 of a throwaway type cutting tool, or of fine filament shaped sensor thin films 8 which are extended to a position parted from each cutting blade edge by a definite distance, is formed up. - 特許庁

ガス絶縁変圧器に使用される絶縁ガスによる地球温暖化への寄与を防止し、またタップ切換器を小型化することにより、コンパクトで高効率な環境調和型ガス絶縁変圧器を提供すること。例文帳に追加

To provide a compact and highly efficient environmentally friendly type gas insulated transformer by preventing insulation gas used in a gas insulated transformer from contributing to global warming and miniaturizing a tap switcher. - 特許庁

原反１４から扇形のカーブベルト１１を切り取り、端縁部同士を接合し、切頭円錐台状に成型する。例文帳に追加

The fan-type curve belt 11 is cut out from the original fabric 14, its end edge parts are connected to each other and it is molded in a cut head truncated conical shape. - 特許庁

所定の切り込み量で金型素材の研削加工を行った後の円盤状砥石２６の外縁２６５をワイヤ放電加工によって切断する。例文帳に追加

The outside edge 265 of the grind wheel 26 after a mold material is ground in a prescribed cut amount is cut by wire electric discharge machining. - 特許庁

箱型の分類ゴミ収納容器（１）の開口部周縁に，複数のＶ字型の切込溝（２）を設け，周胴部に複数の磁石（３）を設ける。例文帳に追加

Plural V-shaped notch grooves 2 are arranged on the opening part peripheral edge of a box-shaped sorting refuse housing vessel 1, and plural magnets 3 are arranged in a peripheral body part. - 特許庁

平型ケーブルのシースを切開する際に、内部に収納された絶縁線心に傷を付けることのない平型ケーブルを提供する。例文帳に追加

To provide a flat cable that is free from damaging the insulated wire core contained inside when the sheath of the flat cable is cut open. - 特許庁

除圧部２を形成する孔部３には孔部３の周縁に非連続切断線５にて型抜き可能に連結した型抜き部６を設ける。例文帳に追加

The part 3 forming the part 2 is provided with a stamping part 6 connected in a stamping possible state by a discontinuous cutting plane line 5 at the periphery of the part 3. - 特許庁