cl-43とは 意味・読み方・使い方

The oscillating-wave motor 44 is so controlled as to make the tilting rotation pinion gear 43 perform a particular action for rotation while alternately repeating normal rotation and reverse rotation within a range of the play CL.例文帳に追加

振動波モータ４４は、チルト回転ピニオンギア４３を上記遊びＣＬの範囲内で正転と逆転を交互に繰り返しながら回転させるための特定の動作をするように、制御される。 - 特許庁

The one oil pressure switch SW and one detection pressure changeover valve 43 are arranged in a hydraulic control system of the frictional engaging device CL of requiring fail-safe, and the detection pressure changeover valve 43 is switched by auxiliary pressure based on operation of an oil pressure control valve 1.例文帳に追加

フェールセーフが要求される摩擦係合装置ＣＬの油圧制御系に、１つの油圧スイッチＳＷと、１つの検出圧切替弁４３とを設け、検出圧切替弁４３を油圧制御弁１の作動に基づく補助油圧によって切り替える。 - 特許庁

A coil winding portion around which the coil 32 is wound such that a winding center line CL of the coil 32 is inclined to the axial line L of a rotational shaft 14 and first and second facing portions 41, 43 provided on the inner and outer periphery sides of the stator core 31 are formed in a stator core 31.例文帳に追加

ステータコア３１には、コイル３２の巻回中心線ＣＬが回転軸１４の軸線Ｌに対し傾斜するようにコイル３２が巻回されたコイル巻回部と、ステータコア３１の内周側及び外周側に設けられた第１及び第２対向部４１，４３とが形成される。 - 特許庁

The IH power source 43 for the fixing device is disposed at the rear part 4R of the main body housing rather than at the intermediate position CL between the front 4F of the main body housing which an operator OR faces and the rear part 4R of the main body housing, which is opposite to the front part 4F.例文帳に追加

操作者ＯＰが向き合う側の本体筐体前部４Ｆと、該前部４Ｆと反対側の本体筐体後部４Ｒとの間の中間位置ＣＬよりも本体筐体後部４Ｒの側に、定着装置のＩＨ電源４３を配置する。 - 特許庁

The soldered part 29 is formed so that an imaginary center circle 43 imagined between an inscribed circle and a circumscribed circle of the soldered part 29 is positioned on the outside of an imaginary ring center line CL imagined in a joint region 21 between a diaphragm support part 11 and the wall part 17 of the sensor case 5 so as to enclose a fluid introduction hole 15.例文帳に追加

被半田付け部２９の内接円と外接円との間に仮想した仮想中心円４３が、ダイアフラム支持部１１とセンサケース５の壁部１７の接合領域２１内に流体導入孔１５を囲むように仮想した仮想環状中心線ＣＬよりも外側に位置するように被半田付け部２９を形成する。 - 特許庁

When the auxiliary port 41 is disconnected from the input port 14, the detection pressure changeover valve 43 is switched to the fail-safe determination side, and the oil pressure switch SW is supplied with the same driving oil pressure as the frictional engaging device CL, and "the fail-safe determination" can be carried out from an ON-OFF state of the oil pressure switch SW.例文帳に追加

また、補助ポート４１が入力ポート１４と遮断されると検出圧切替弁４３がフェールセーフ判定側へ切り替わり、油圧スイッチＳＷに摩擦係合装置ＣＬと同じ駆動油圧が与えられて、油圧スイッチＳＷのＯＮ−ＯＦＦ状態から「フェールセーフ判定」を行うことができる。 - 特許庁