That is, when a control device 1 is provided with a function for deciding the short-circuit state and disconnected state of the sensor based on the voltage of the input terminal, the erroneous connection of the power supply built-in type sensor 19 is decided by using the decision function only by adding the switch circuit 6. すなわち、制御装置1が、入力端子の電圧に基づいてセンサの短絡状態,断線状態を判定する機能を備えている場合、スイッチ回路6を追加するだけで上記判定機能を利用して電源内蔵型センサ19の誤接続を判定できるようになる。 - 特許庁
A control part 31 requests input of information for determining electric energy to be charged by operating a display part 39 comprising a touch panel, when a vehicle ID previously registered to an external storage device 13 and a vehicle ID acquired by a reader/writer 34 are equal. 外部記憶装置13に予め登録されている自動車IDと、リーダライタ34により取得された自動車IDとが一致すると、制御部31は、タッチパネルからなる表示部39が操作されることにより充電する電力量を決める情報を入力するように要求する。 - 特許庁
Further, the in-vehicle equipment control device S may be provided with a set value increase/decrease re-starting means 14 when inputs by the input means 2, 3 are continued for a predetermined time after the increase/decrease of the set value is stopped by the set value increase/decrease stopping means 13. また、車載機器制御装置Sは、設定値増減停止手段13により設定値の増減が停止された後、入力手段2、3による入力が所定時間継続された場合に、設定値の増減を再開させる設定値増減再開手段14を備えるようにしてもよい。 - 特許庁
Based on the input position information of the periphery of the eye E, a control unit constituted of a microprocessor incorporated in the imaging unit 1 sets a particular area Z, so that a red eye correction function is executed as limited to the above particular area Z. 特定領域Z内に限定して赤目補正機能が実行されるので、複雑な検出プログラムを必要とせずに、画像の全領域を対象にして補正機能が実行される場合に比べて短時間で正確に赤目部分が検出され、より的確な赤目補正が行われる。 - 特許庁
If the amount of the input packets received by the buffer is greater than the threshold value, a transmission packet control section 203 divides the received packets into the amount of the threshold value and the remaining amount, transmits the received packets of the threshold value to the line terminator LT2, and stores the remaining received packets in the buffer. 送出パケット制御部203は、もしもバッファに入力された入力パケットが閾値より多い場合は、入力パケットを閾値分と残りに分割し、閾値分の入力パケットを局内加入者収容装置LT2に送出し、残りの入力パケットはバッファに蓄える。 - 特許庁
When the slip control is in progress, if a value obtained by correcting, on the basis of a slip revolution speed, an actual transmission ratio being a ratio of an input revolution speed to an output revolution speed of this automatic transmission is out of a predetermined range of a target transmission ratio, abnormality is determined to occur in the automatic transmission. スリップ制御中は、自動変速機の出力回転数に対する入力回転数の比である実際の変速比をスリップ回転数に基づき補正した値が、目標変速比の所定範囲外であるときには、変速機内に異常が発生していると判定することとした。 - 特許庁
An image processing device 3002 is provided with a plurality of functional block 3004 to 3012 which receive a print data and perform phased development until raster image, and a channel control unit 303 which controls to specify a functional block 3004 to 3012 to input the print data based on the print data. 本発明の画像処理装置3002は、印刷データを受けて段階的にラスター画像まで展開していく複数の機能ブロック3004〜3012と、印刷データに基づきどの機能ブロック3004〜3012へ印刷データを入力するかを制御する経路制御部3003とを備えている。 - 特許庁
A map setting circuit 26 included in a display control circuit 200 of the liquid crystal display device has a conversion map from input gradation data to output gradation data, and changes a portion of the content of the conversion map according to a display mode signal (Md) given from the outside of the device. 本液晶表示装置の表示制御回路200に含まれるマップ設定回路26は、入力階調データから出力階調データへの変換マップを有しており、装置外部から与えられる表示モード信号Mdに応じて変換マップの内容を一部変更する。 - 特許庁
A packet position calculation unit 323 of the information write control unit 301 reports the packet number of a packet having been written to the stream table generating unit 307, and sets a readout flag of a packet number of the packet table 312 corresponding to the input packet number to "0" (S310). 情報書込制御部301のパケット位置算出部323は、書込みを完了したパケットのパケット番号をストリームテーブル生成部307に通知し、入力されたパケット番号に該当するパケットテーブル312のパケット番号の読出しフラグを「0」に設定する(S310)。 - 特許庁
To provide a control circuit for a DC-DC converter which can be built in a logic circuit by being equipped with a digital error amplifier capable of controlling the gain, according to input voltage and output voltage, and obviating an accurate resistor and a capacitor to be used for a feedback circuit or the like. 入力電圧と出力電圧とに応じて利得を制御可能なデジタル誤差増幅器を備え、帰還回路等に使用する高精度な抵抗やキャパシタを不要とすることで、ロジック回路内に内蔵可能なDC−DCコンバータの制御回路を提供すること。 - 特許庁
After a signal is input to a clocking correction means 19 from a control means 21 before repeated operations, the correction means 19 directs an instrumentation start, after the preparatory repeated operations are performed only a predetermined preparatory repetition number Npr times, and a clocking means 18 starts its normal operation. 繰返し動作の前において制御手段21から計時補正手段19に信号が入力された後、計時補正手段19は予め定めた事前繰返し回数Nprだけ事前繰返し動作を行った後は計測開始を指示し、計時手段18が正規の動作を開始する。 - 特許庁
The CPU 56 operates in accordance with a program stored in a ROM and performs a power supply stoppage process and outputs a power cutoff signal to a putting-out control board 37 when recognizing input of the power cutoff signal from the power board 910. ROMに格納されているプログラムに従って動作するCPU56は、電源基板910から電断信号が入力されたことを認識すると、電力供給停止時処理を実行するとともに払出制御基板37に対して電源断信号を出力する。 - 特許庁
A laser device 101 is used for a light source 1, control parts 205, 206 which input drive current to the laser 101 corresponding to information are provided and a focal adjustment part 3 consisting of a variable focal lens is provided on an optical path of light emitted from the light 1. 光源1にレーザ装置101が用いられ、情報に対応して駆動電流をレーザ装置101に入力する制御部205、206が備えられ、光源1から出射される光の光路上に、可変焦点レンズより成る焦点調整部3が設けられる。 - 特許庁
If the instruction input for selecting any one of the reproduced digital data is received, the control section 207 generates uplink information expressed by using the identification code of the selected digital data and prescribed character string data and sends it as order data of the merchandise or the service to the distribution server. 再生されたディジタルデータのいすれかを選択する指示入力を受け付けると、制御部207は、選択されたディジタルデータの識別符号と所定の文字列データを用いて表されるアップリンク情報を生成し、商品又は役務の注文データとして配信サーバに送信する。 - 特許庁
The above compressed image signal and the above converted VGA signal are both sent to a switch 115 so that either can be selected according to the result obtained by classifying the control information input via a digital interface 118 from the outside by means of a classification device 120 and then output via the digital interface 118. 上記圧縮された画像信号と上記VGA信号とはスイッチ115に送られ、その一方が外部からデジタルインターフェース118を介して入力される制御情報を判別部120で判別した結果に応じて選択され、デジタルインターフェース118を介して出力される。 - 特許庁
To properly determine whether to prohibit lock-up at the start of a soak condition, in a control device for an automatic transmission for changing speed of an internal combustion engine, which is input through a torque converter possible to be locked up, and for outputting it. ロックアップ可能なトルクコンバータを介して入力される内燃機関の回転を変速して出力する自動変速機の制御装置においてソーク状態の始動においてロックアップの禁止の可否を適切に判断するようにした変速機の制御装置を提供する。 - 特許庁
To provide a signal output circuit including: a shut-down function of shutting down an operation of an internal circuit; and a mute function of muting an input signal and capable of controlling the shut-down function and the mute function by using a single external control signal. 内部回路の動作をシャットダウンさせるシャットダウン機能及び信号をミュートさせるミュート機能を有する信号出力回路に関し、一つの外部制御信号でシャットダウン機能及びミュート機能を制御できる信号出力回路を提供することを目的とする。 - 特許庁
The reference circuit is provided with a second input transistor subjected to cascade connection, a second cascode transistor and a second transistor for bias current control, and is connected to the tuning amplifier circuit in parallel, wherein the gate of the second cascode transistor is connected to the gate of the first cascode transistor. 参照回路は、従属接続される第2の入力トランジスタ、第2のカスコードトランジスタおよび第2のバイアス電流制御用トランジスタを備え、第2のカスコードトランジスタのゲートが第1のカスコードトランジスタのゲートに接続され、同調増幅回路と並列に接続される。 - 特許庁
In this gear ratio control device for a continuously variable transmission 60 for controlling a gear ratio in the continuously variable transmission connected to an engine, setting means 51-55 set a target rotating speed of an input part 21 of the continuous variable transmission based on a target output of the engine at traveling downhill. エンジンに接続された無段変速機における変速比を制御する無段変速機の変速比制御装置60では、設定手段51〜55が、降坂路走行時にエンジンの目標出力に基づいて無段変速機の入力部21の目標回転速度を設定する。 - 特許庁
A fault-analyzing operation control portion 41 creates a series of screens, including a screen displaying the information of a list of past faults and a screen displaying the logs relating to each operation executed in solving the fault and makes the same output to the input/output device 1. 障害分析操作制御部41は、過去に発生した各障害の一覧情報を表示する画面、および障害対処時に行われた個々の操作に関するログを表示する画面を含む一連の画面を生成し、入出力装置1に出力させる。 - 特許庁
A dirt detecting sensor 8 and a control part for driving the fan 2 when a dirt measured value measured by an input signal from the dirt detecting sensor 8 is higher than the present dirt standard value and for stopping the fan 2 or for reducing the number of rotation of the fan 2 when the dirt measured value is lower are provided. 汚れ検知センサ8と、汚れ検知センサ8からの入力信号により計測される汚れ計測値が現在の汚れ基準値よりも高いときはファン2を駆動させ、低いときはファン2を停止又はファン2の回転数を低下させる制御部とを備える。 - 特許庁
In S150, the microcomputer judges the signal input from the reversing end limit switch to display alarm, to stop the motor (S170) and then to transfer to ordinary control (S180), when the slide member is positioned at the reversing end, and to transfer to abnormality display (S200), when the slide member is positioned at the place excluding the reversing end. S150にて、マイコンは後進端リミットスイッチからの入力された信号を判断し、スライド部材が後進端にある場合は警報表示とモーター停止(S170)し、その後、通常制御(S180)に移行され、後進端以外に有る場合は異常表示(S200)に移行する。 - 特許庁
A control IC chip 23 is face down mounted on the surface of a substrate 10 where electrothermal conversion elements 12, ink channels 21 and ink ejection openings 22 are formed and the input side of the IC chip 23 is connected with the lead-out electrode of a flexible printed board 30. 電気熱変換素子12およびインク流路21やインク吐出口22を形成した基板10の表面に、制御用のICチップ23をフェースダウンで実装するとともに、ICチップ23の入力側をフレキシブルプリント基板30の外部取出し電極に接続する。 - 特許庁
A protocol processing part 3 executes processing on the basis of three sorts of input information set by a user and concerned with link fault detection results, four-bit switching control information and terminal information which are inputted from a network side port #1 processing part 4 and a network side port #2 processing part 5. プロトコル処理部3はネットワーク側ポート#1処理部4及びネットワーク側ポート#2処理部5から入力されるリンク障害検出結果及び4ビットの切替え制御情報と、さらに終端情報とに関するユーザ設定の3種類の入力情報を基に処理を実施する。 - 特許庁
Since the phase advance capacitors 4a and 4b are not inputted to the building side power distribution system when starting operation of the elevator by performing such control, damage of various apparatuses of the elevator caused by spike voltage by input of the phase advance capacitors 4a and 4b, can be prevented. このような制御を行なうことで、エレベータの運転が開始された際に進相コンデンサ4a,4bが建屋側配電系統に投入されなくなるので、進相コンデンサ4a,4bの投入によるスパイク電圧に起因するエレベータの各種機器の破損を防止することができる。 - 特許庁
A control part for performing dispensing processing of a prescribed number of game balls in response to the dispensing request of game balls based on an operation input from an operation part neglects the dispensing request when the dispensing request is given if a remainder detection output is transmitted from the remainder detection sensor. 操作部からの操作入力に基づく遊技球の貸出要求に応じて所定数の遊技球の貸出し処理を行う制御部は、残存検知センサから残存検知出力が送出されている場合において、貸出要求があった場合には、当該貸出要求を無視する。 - 特許庁
The control section stores addresses wherein the input image data are stored to an array A, and an image processing section rearranges addresses stored in the first half or the latter half of the array A such that the page numbers are in the descending order on the basis of the instruction data as above. 制御部は入力画像データが格納されたアドレスを配列Aに格納し、画像処理部は、前述の指示データが示す指示データに基づいて、前述の配列Aの前半または後半部分に格納されているアドレスをページ番号が降順となるよう並べ替える。 - 特許庁
When detecting an obstacle existing on the road of a vehicle or near the route on the basis of input from various radars, a vehicle control device obtains , for example, obstacle information related to the detected obstacle and vehicle relevant information related to the vehicle from the various radars or the like. 車両制御装置は、例えば、各種レーダからの入力に基づいて、自車両の進路または進路近傍に障害物を検知すると、検知された障害物に関する障害物情報、および自車両に関する自車両関連情報を各種レーダ等から取得する。 - 特許庁
The recording liquid container 5 has a composition in which the volume of the recording liquid L is detected by receiving a control signal coming from the recording apparatus at a signal input portion 3 and applying a voltage between a pair of electrodes 6a and 6b provided in an internal portion to contain the recording liquid having conductivity. 記録液収納容器5は、記録装置からの制御信号を信号入力部3で受け、導電性を有する記録液を収容可能な内部に備えられた一対の電極6a,6b間に電圧を印加することで記録液Lの量を検知可能な構成である。 - 特許庁
The control circuit 3 uses the respective values Tn, Zn in the memory, and detects input voltage Vin and an output voltage Iot to calculate a time To in accordance with the following expression, and switches a transistor Q1 from off to on when the time To has passed since the off-time of the transistor Q1. 制御回路3は、メモリの各値Tn,Znと検出した入力電圧Vinおよび出力電流Iotとを用いて、下記式に従って時間Toを算出し、トランジスタQ1のオフ時点から時間Toが経過した時点で、トランジスタQ1をオフからオンに切り替える。 - 特許庁
A data input part 2 and a printing part 7 are constituted to change a printing order of each image data so that an output control unit 5 makes the printing part print images of the other sizes at a time after having the printing part print images of one size among the plurality of sizes printed at a time. データ入力部2と印刷部7とを出力制御部5が複数のサイズのうちの一のサイズを一括して印刷部に印刷させた後、他のサイズの画像を一括して印刷させるように各画像データの印刷順序を変更する構成を特徴とする。 - 特許庁
This information processor is adapted to deliver a report to a higher layer via a control device (operation button management device) 2 interposed between operation elements such as an operation button A-1, A-2, etc. and operation input devices Device A, Device B, etc. such as pointing devices to perform application processing. 操作釦「A−1」、「A−2」、…等の操作要素と、ポインティングデバイス等の操作入力用デバイス「Device A」、「Device B」、…との間に介在される制御デバイス(操作釦管理用デバイス)2を経由して上位階層へと通知が届けられて、アプリケーション処理が行われる構成にした。 - 特許庁
The gaming machine generates a ball shooting inhibition state by stopping the driving of a ball shooting motor 18, when detecting no game ball used for a game, and in the ball shooting inhibition state, abnormal condition notification is executed when a prize winning ball detecting signal is input into a payout control board 17. 遊技に使用可能な遊技玉が0になったを検知して打球発射モータ18の駆動を停止しては発射禁止状態にし、発射禁止状態において、入賞玉検出信号が払出制御基板17に入力されたときに異常報知を行なう。 - 特許庁
This device comprises a temperature rise control part 15 for processing input present speed and pressure as predetermined and outputting a first switch instruction and a switch part 16 to be controlled by the first switch instruction for controlling the ON/OFF of a power supply to a fan motor 7a. 現在速度および現在圧力を入力として所定の処理を行って第1のスイッチ指令を出力する昇温制御部15と、第1のスイッチ指令により制御されてファンモータ7aへの供給電源のON/OFFを制御するスイッチ部16とを有している。 - 特許庁
Nearly simultaneously therewith, hydraulic pressure rise control is executed such that belt pinching pressure in the variable speed part 20 comprising a belt type continuously variable transmission is raised, and slippage of a belt 44 is prevented even if input torque of the variable speed part 20 rises, thus improving durability of the variable speed part 20. これと略同時に、ベルト式無段変速機で成る無段変速部20のベルト挟圧を上昇させように油圧上昇制御を実行し、無段変速部20の入力トルクが上昇してもベルト44に滑りが生じないようにして無段変速部20の耐久性を向上させる。 - 特許庁
Namely, the voltage variation interference is lightened by controlling, to reduce the energization to the fixing heater by an engine control part ECNT, when changes, such as the increase or the decrease in the input current, continues for the preset prescribed time or longer in the image forming apparatus that has a fixing device. すなわち、定着装置を有する画像形成装置で、入力電流の増加または減少の変化が予め定められた所定時間以上継続した時に、エンジン制御部ECNTが定着ヒータへの通電を下げるように制御し、電圧変動妨害を軽減する。 - 特許庁
A clamp circuit 256 inside a signal level control part 202 inputs an image signal from a CCD 108 via an amplifier 252 and a capacitor 254, and sets a black level of the relevant image signal to a level that does not exceed a critical value of a black level for the input of an AFE 206 at a post-stage. 信号レベル制御部202内のクランプ回路256は、アンプ252及びコンデンサ254を介してCCD108からの画像信号を入力し、当該画像信号の黒レベルを後段のAFE206の入力の黒レベルの限界値を超えないレベルに設定する。 - 特許庁
The main control part 11 (deviation comparison determination part of the function processing part 35) outputs a re-search signal to a re-search processing part 33 when a difference between the estimated arrival time and the actual time exceeds a reference value, and the re-search processing part 33 conducts re-search when the re-search signal is input. 主制御部11(機能処理部35の偏差比較判定部)は、その推定到達時刻と実時刻との差が基準値を超える場合に探索処理部33に再探索信号を出力し、再探索信号が入力された場合に探索処理部33は、再探索を行う。 - 特許庁
When an observer operates a designated switch provided to an input unit 11, a control unit 9 drives a motor 14 for rotating a motor-driven revolver 14 by a quantity of one objective 6 in a direction, corresponding to the kind of the switch, thereby switching the objective 6. 制御ユニット9は、入力ユニット11に設けられた所定のスイッチを観察者が操作すると、モータ14を駆動して、電動レボルバ7をそのスイッチの種類に応じた方向に1個の対物レンズ6分、回転させることにより、対物レンズ6の切り換えを行う。 - 特許庁
The digital stamp includes a container 6 holding resin cured by light energy; an irradiation part 23 irradiating the resin with light emitted from a light source 24; a pattern input part 12 inputting a pattern; and an irradiation control part 20 controlling the irradiation region of light based on the pattern. 光エネルギーにより硬化する樹脂を保持する容器6と、光源24から射出された光を前記樹脂に照射する照射部23と、パターンを入力するパターン入力部12と、前記パターンに基づいて前記光の照射領域を制御する照射制御部20とを備える。 - 特許庁
The information processor is provided with a screen display part 101 composed integrally with a tablet 109, a mode determining part 105 determining whether or not it is in an input mode using the tablet 109, and a mode control part 113 changing a user interface on the basis of a determination result of the mode determining part 105. タブレット109と一体に構成された画面表示部101と、タブレット109による入力モードか否かを判定するモード判定部105と、このモード判定部105の判定結果に基づいてユーザインターフェース切り替えるモード制御部113とを備えた情報処理装置。 - 特許庁
The input terminal 10, the output terminals 12, and terminals 16 for the board to be connected with the control circuit board 18 are arranged, in parallel with the direction of arrangement of the semiconductor switching elements 14, and are made to protrude from a case 22 in the same orientation to directly form connectors. 入力端子10、出力端子12、及び、前記制御回路基板18に接続される基板用端子16が、前記半導体スイッチング素子14の配列方向と平行に配列され、かつ、互いに同じ向きにケース22から突出して直接コネクタを形成する。 - 特許庁
This device is a semiconductor device to which multilevel information can be written electrically, bit lines are connected to input/output terminals of right and left of a sense latch circuit, a data latch circuit is connected to each bit line, and the device is provided with a decoder decoding write data externally supplied and generating write control information. 電気的に多値情報が書込み可能にされる半導体装置であり、センスラッチ回路の左右の入出力端子にビット線を接続し、各ビット線にデータラッチ回路を接続し、外部から供給される書込みデータをデコードして書込み制御情報を生成するデコーダを設ける。 - 特許庁
Or, a control unit 11 displays a screen saver or an advertisement on the display part 12 in the case an operation signal is not inputted from the operation input part 13 for a preset time, and icons showing the operation state of each function are displayed on the screen saver. あるいは、制御部11は、予め設定された所定時間、操作入力部13から操作信号が入力されなければ、表示部12にスクリーンセーバー又は広告を表示させるとともに、各機能の動作状況を示すアイコンをスクリーンセーバー上にアイコン表示する。 - 特許庁
The digital sound recording device of this invention includes an input unit, a storage unit, a data communication unit, and a processor, then further a write protection unit is included between the storage device and the data communication unit, thereby, it is prevented that write control is performed on the storage unit by the external unit. 本発明のデジタル録音装置は、入力装置、記憶装置、データ通信装置、およびプロセッサを含み、記憶装置とデータ通信装置との間に書き込み防止装置をさらに含むことにより、外部装置から前記記憶装置に書き込み制御を行うことを防止することを特徴とする。 - 特許庁
Moving amount of a cleaning roller C in the print medium carrying passage is detected as the thickness of a plate and when the detected thickness exceeds a specified value and a sheet is inputted by a print medium input means, operation of a cutting means is interrupted by a cutting control means 50. 印刷媒体搬送経路中のクリーニングローラCの移動量をプレートの厚みとして検出し、この検出結果が所定の厚さ以上で印刷媒体入力手段による印刷媒体の入力がシート類の場合、切断手段の動作を中止させる切断制御手段50とを備える - 特許庁
In second encoding processing, the encoding parameter stored in the external DRAM 411 is transferred through the external DRAM 411 to the parameter input/output part 408, which imparts the acquired encoding parameter to the signal processing parts 403 to 406 via the encoding control part 407. 第2の符号化処理の際、外部DRAM411に格納された符号化パラメータは外部DRAM411を経由してパラメータ入出力部408に渡され、パラメータ入出力部408は、入手した符号化パラメータを、符号化制御部407を介して各信号処理部403〜406に与える。 - 特許庁
The expansion processing unit 17 executes expansion processing for expanding the range determined in the image analysis unit 16 for the image information input from the image capturing unit 12 on the basis of the instruction of a control unit 14 and outputs the image information after the processing to an image information processing unit 18. 拡大処理部17は、制御部14の指示に基づき、撮像部12から入力される画像情報に対して、画像解析部16で特定された範囲を拡大するための拡大処理を施し、処理後の画像情報を画像情報処理部18に出力する。 - 特許庁
In this case, when detecting the input start of the data strings, a control processing part 14 operates a frame counter 14a and before the lapse of a period for inputting data strings for one frame, the part 14 discriminates whether all of the data memories 10 have started writing of the data strings. この際、制御処理部14は、データ列の入力開始を検出すると、フレームカウンタ14aを動作させ、1フレーム分のデータ列が入力される時間が経過する以前に、複数のデータメモリ10がいずれもデータ列の書込を開始したか否かを判別する。 - 特許庁
Counting from a point of time when a logical value of a signal input into a clock control terminal 13 is switched to 1, just after a second fall of a pulse output from the PLL 204, a clock generation part 6 is operated to start outputting a clock signal of the PLL 204 from the AND gate 209. クロック生成部6は、クロック制御端子13に入力される信号の論理値が1に切替わった時点から数えて、PLL204から出力されたパルスの2番目の立下りの直後に、ANDゲート209からPLL204のクロック信号を出力し始めるように動作する。 - 特許庁