To keep a transmitting analog output signal constant without being subject to the effect of a gain abnormality on the feedback side, even when the gain abnormality is generated on the feedback side of a gain-control loop. 利得制御ループの帰還側で利得異常が発生した場合でも、帰還側の利得異常の影響を受けずに送信アナログ出力信号を一定にする。 - 特許庁
The spindle device with the chuck is equipped with: a position detector 41 detecting the rotational angle position of the spindle 22; and a positioning control means 5a controlling a spindle drive motor 4 in a closed loop. 主軸22の回転角度位置を検出する位置検出器41と、主軸駆動モータ4を閉ループで制御する位置決め制御手段5aとを備える。 - 特許庁
In order to first remove the looseness existing in the mechanism to transmit the driving force of the ultrasonic motor 3, the ultrasonic motor 3 is driven by a driving signal for removing the looseness through open loopcontrol. まず、超音波モータ3の駆動力を伝達する機構に存在するガタを取るため、オープンループ制御によるガタ取り用駆動信号で超音波モータ3を駆動する。 - 特許庁
A PLLIC 20 used in a PDC (personal digital cellular) portable telephone set is provided with a loop filter block 30 controlled by a frequency control signal outputted from a register 23. PDC方式の携帯電話機に使用するPLLIC20に、レジスタ23から出力される周波数制御信号により制御されるループフィルタブロック30を配設する。 - 特許庁
To provide a clock control circuit wherein center frequency fluctuation caused when a PLL circuit is used as well as jitter and the like caused by a feedback loop are eliminated, for significantly reduced phase error. PLL回路を用いた場合に生じる中心周波数変動、及び、帰還ループによるジッタ等を無くし位相誤差を特段に低減するクロック制御回路の提供。 - 特許庁
An antenna section 3 is provided at a left side on a board 2 and an input output terminal 4 and a control terminal 5 of a phase-locked loop circuit 7 are provided at a right side on the board 2. 基板2上の左側にアンテナ部3を、また、基板2上の右側に入出力端子4及びフェイズロックドループ回路7の制御用端子5を配設する。 - 特許庁
The game control means transmits a command on the number of prize balls based on counter values of the respective prize ball command output counters in a main process (a main loop). また、遊技制御手段は、メイン処理(メインループ)において、各賞球コマンド出力カウンタのカウント値にもとづいて、賞球個数コマンドを払出制御手段に送信する。 - 特許庁
When the control voltage and the gain are denoted by V and k, respectively, the value of Vc×k is constant, independently of whether the oscillation in the oscillation loop is in a steady-state or in a start-up process. 制御電圧をVc、ゲインをkとした場合に、発振ループ内の発振が定常状態か起動過程かにかかわらず、Vc×kの値が一定である。 - 特許庁
To provide a closed-loop control system which controls the light-caused delamination of matrix tissues in a surgical treatment for inner matrices of cornea tissues in order to improve eyesight. 眼の視力を向上させるために、角膜組織における基質内部の外科処置に際し、基質組織の光による剥離を抑制する閉ループ・システムを提供する。 - 特許庁
The processing concerning the guard of a shared part of a tenant building is carried out by a system consisting of a crime prevention control part 30, the terminal units 40 of the part 30 and a crime prevention sensor loop serving as a terminal device. テナントビルの共用部の警備に関する処理は、防犯制御部30、その端末ユニット40及び端末器である防犯センサループの系統で行われる。 - 特許庁
When the sensor output becomes the state inclined to the upper limit value IUL or the lower limit value ILL, the feed power to the heater is determined by open loopcontrol. 一方、センサ出力が上限値I_UL又は下限値I_LLへはりついた状態になっているときには、オープンループ制御によりヒータへの供給電力を決定する。 - 特許庁
To provide an air-fuel ratio control device of an internal combustion engine capable of highly accurately determining a learning correction value in an open loop operation area by using an ordinary air-fuel ratio sensor. 通常の空燃比センサを用いてオープンループ運転領域での学習補正値を高精度に求めることのできる内燃機関の空燃比制御装置を得る。 - 特許庁
A 1st frequency error detection circuit 14 outputs a frequency error Δθ1ave with low accuracy over a wide frequency range to configure a loop (a) relating to feedforward control. 第1周波数誤差検出回路14では広周波数範囲かつ低精度の周波数誤差Δθ1^aveを出力し、フィードフォワード制御に係るループaを構成する。 - 特許庁
This method and device for improving process performance over the service life of the polishing pad in the chemical-mechanical polishing device uses closed loopcontrol for abrasion of the polishing pad. ケミカルメカニカルポリシング装置におけるポリシングパッドの寿命にわたってプロセス性能を高める方法および装置は、ポリシングパッドの磨耗の閉ループ制御を使用する。 - 特許庁
An open loopcontrol portion 22 obtains command voltages v_d, v_q on the dq axis, in accordance with a circuit equation of the motor, based on the command currents i_d*, i_q* and an angular velocity ω_e. オープンループ制御部22は、指令電流i_d^* 、i_q^* と角速度ω_e に基づき、モータの回路方程式に従いdq軸上の指令電圧v_d 、v_q を求める。 - 特許庁
A driving device 103, coupled to the first mass, forms a controlloop for maintaining the first mass in oscillation at a resonance frequency. 前記第1の質量体に結合された駆動装置103が、この第1の質量体を共振振動数で振動状態に維持する制御ループを構成する。 - 特許庁
When it is instructed to carry out a layer jump, the contact of a change-over switch 153 is changed over and becomes open by a signal from a sequential control circuit 131A, and a focus servo loop becomes open. レイヤジャンプの指令があったときに、シーケンス制御回路131Aからの信号により切換えスイッチ153の接点が切換わり、フォーカスサーボループが開となる。 - 特許庁
The actual EGR quantity is estimated and calculated, and the EGR valve opening is closed-loop controlled by PI control based on the deviation with the target EGR quantity according to an operation state. 実EGR量を推定演算し、運転状態に応じた目標EGR量との偏差に基づいて、EGR弁開度をPI制御によりクローズドループ制御する。 - 特許庁
To allow an external output controlloop method for setting a target SIR using a measured FER to work sufficiently in a high-speed fading state. 高速フェーディングの状況において、計測FERを用いて目標SIRを設定する外部出力制御ループ方法が十分に機能するようにすること。 - 特許庁
A control circuit 20 switches the conveying speed of the recording material S in the fixing device 12 to two stages, high and low stages, on the basis of output from the loop detection device 21. 制御回路20は、ループ検知装置21の出力に基づいて、定着装置12における記録材Sの搬送速度を高低2段階に切り替える。 - 特許庁
To provide an adjustment method which optimizes performance of a controlloop of a micro electromechanical system (MEMS) which has the gain and the resonance frequency considerably varied by parts. 利得と共振周波数が部品によって大幅に異なるマイクロ電気機械装置(MEMS)の制御ループの性能を最適にする調整方法を提供する。 - 特許庁
To provide an AGC (automatic gain control) circuit which operates stably, even if the time constant of an AGC loop of the AGC circuit is not larger than the period of input signal. AGC回路のAGCループの時定数が入力信号の周期よりも十分に大きくないときでも、安定した回路動作をするAGC回路の提供。 - 特許庁
The control circuit controls the frequency characteristics of the low-pass filter so that the oscillation frequency of the loop circuit fits in a predetermined range, in the correction mode of the filter circuit. 制御回路は、フィルタ回路の校正モード時に、ループ回路の発振周波数が所定範囲内に収まるようにローパスフィルタの周波数特性を制御する。 - 特許庁
The control valve 10 is changed from the solid line to a dotted line shown in a figure to introduce an additive component stored in the sample loop 11 into a reversed phase chromatography column 12 (ODS column). 六方切換えバルブ10を実線から点線に切り換え、サンプルループにためられた添加剤成分を、逆相クロマトグラフ用カラム(ODSカラム)12に導入する。 - 特許庁
The fluid control device of a manual or open loopcontrol type comprises a fluid control valve for controlling the pressure of a fluid in response to a pressure operation of a control fluid, and a switch valve for opening or stopping the flow of the fluid. 本発明に係る流体制御装置は、手動式または開ループ制御式流体制御装置であり、制御用流体の圧力操作により流体の圧力を制御する流体制御弁と、前記流体の流れを開放又は遮断するための開閉弁とを具備することを特徴としている。 - 特許庁
This slip control device for a torque converter has a slip control means switching from open loopcontrol to slip control based on an operating condition of a vehicle and controlling an engagement state of a lockup clutch. 車両の運転状態に基づいてオープンループ制御からスリップ制御に切り換えてりロックアップクラッチの締結状態を制御するスリップ制御手段と、を備え、前記スリップ制御手段は、F/F制御系ではF/Fスリップ回転速度指令値と、F/Fスリップ回転速度ゲインとからF/F目標コンバータトルクを演算する。 - 特許庁
When the DC output voltage V_out deviates from the range of a monitoring value AM, the control section 12 does not stop switching control operation of the control system but sustains switching control operation, by switching the response characteristics (especially, the response characteristics of an error amplifier 14) of a feedback/loop system to higher response characteristics. 制御部12では、直流出力電圧V_outが監視値AMの範囲を出たときは、制御系のスイッチング制御動作を停止させるのではなく、フィードバック・ループ系の応答特性(特に誤差増幅器14の応答特性)を応答性の高いものに切り換えてスイッチング制御動作を続行させる。 - 特許庁
A method of controlling downlink transmission from a base station having multiple antennas to a mobile station having multiple antennas includes the steps of: applying open loop-type MIMO diversity to a common control channels, an MBMS channel, and an L1/L2 control channel; and applying closed loop-type MIMO multiplexing and/or MIMO diversity to a shared data channel. 複数のアンテナを有する基地局から複数のアンテナを有する移動局への下りリンク伝送制御方法において、共通制御チャネル、MBMSチャネル、L1/L2制御チャネルに対して、開ループ型のMIMOダイバーシチを適用し、共有デーダチャネルに対して、閉ループ型のMIMO多重および/またはMIMOダイバーシチを適用する。 - 特許庁
A controller 115 supplies the output of the spot position loop filter 109 to a tracking actuator 104 before supplying the output of the transfers loop filter 111 to a traverse motor 113, preliminarily moves the light spot to the neighborhood of the center of the light receiving element 105, and starts traverse control in a state that the value of the spot position signal at the time of starting traverse control is reduced. コントローラ115はトラバースループフィルタ111の出力をトラバースモータ113に供給する前に、スポット位置ループフィルタ109の出力をトラッキングアクチュエータ104に供給し、光スポットをあらかじめ受光素子105の中心付近に移動させ、トラバース制御開始時のスポット位置信号の値を小さくした状態で、トラバース制御を開始する。 - 特許庁
A control signal controlling the voltage control oscillator 7 is generated through a phase error detector 3 and a digital loop filter 4, and since the digital loop filter 4 is constituted of a digital filter processing with a reproduced clock being n/m-frequency-divided, even if a reproducing channel rate is varied with a rate of n/m, the frequency characteristic is varied with similarity in accordance with it. 電圧制御発振器7を制御する制御信号は、位相誤差検出器3およびディジタルループフィルタ4を経て生成されるが、このディジタルループフィルタ4が、n/m分周した再生クロックで処理するディジタルフィルタで構成することによって、再生チャンネルレートがn/mの比率で変化しても、それに応じた相似形でその周波数特性が変化する。 - 特許庁
A fractional-N mode phase synchronous circuit is provided with, between a loop filter and a voltage control oscillator 6, a low-pass filter 9 with a cutoff frequency which is fully higher than a loop bandwidth frequency of the phase synchronous circuit and which determines a fractional frequency division ratio of a PLL control circuit 8, and which is fully lower than a periodic frequency. フラクショナル−N方式の位相同期回路において、ループフィルタと電圧制御発振器6の間に位相同期回路のループ帯域周波数より十分高くかつPLL制御回路8の分数分周比を決定する周期周波数より十分低い遮断周波数をもつ低域通過フィルタ9を備えたものである。 - 特許庁
In a method for controlling downlink transmission from a base station, having a plurality of antennas to a mobile station having a plurality of antennas, an open-loop MIMO diversity is applied to a common control channel, an MBMS channel, and an L1/L2 control channel, while a closed-loop MIMO multiplex and/or MIMO diversity is applied to a shared data channel. 複数のアンテナを有する基地局から複数のアンテナを有する移動局への下りリンク伝送制御方法において、共通制御チャネル、MBMSチャネル、L1/L2制御チャネルに対して、開ループ型のMIMOダイバーシチを適用し、共有デーダチャネルに対して、閉ループ型のMIMO多重および/またはMIMOダイバーシチを適用する。 - 特許庁
In the transmission power controlling method for performing outer loop transmission power control for updating the target SIR to be used for the inner loopcontrol so that the receiving quality of received data approaches target quality, the changing width of the target SIR is not set to a fixed value but is adaptively changed in accordance with the value of a current target SIR. 受信したデータの受信品質が与えられた目標品質に近づくように、インナーループ制御において使用されるターゲットSIRを更新するアウターループ送信電力制御を行う送信電力制御方法において、ターゲットSIRの変化幅を一定値にするのではなく、現在のターゲットSIRの大きさに応じて適応的に変化させる。 - 特許庁
By a controller 115, an output of the spot position loop filter 109 is supplied to a tracking actuator 104 before an output of the traverse loop filter 111 is supplied to a traverse motor 113, then the light spot is preliminarily moved to near the center of the photodetector 105 and the traverse control is started in the state a value of the spot position signal at the start of the traverse control is reduced. コントローラ115はトラバースループフィルタ111の出力をトラバースモータ113に供給する前に、スポット位置ループフィルタ109の出力をトラッキングアクチュエータ104に供給し、光スポットをあらかじめ受光素子105の中心付近に移動させ、トラバース制御開始時のスポット位置信号の値を小さくした状態で、トラバース制御を開始する。 - 特許庁
A mechanism (25) is arranged on at least a drive controller (22) so as to generate a rotational vibration compensating quantity suitable for compensating the rotational vibration on line by a drive controlloop only from at least a quantity of state of the drive controlloop having the respective drive controller (22) therein during the operation of the printing machine. 本発明によれば、少なくとも1つの駆動制御器(22)に、印刷機の稼動中、それぞれ当該の駆動制御器(22)が組み込まれている駆動制御ループの少なくとも1つの状態量から、専らこの駆動制御ループで回転振動の補償に適した回転振動補償量をオンラインで生成する機構(25)が配備される。 - 特許庁
A controller 5 is provided with a first controlloop for positioning the relative position of the vibration resistant table 10 to the base by feeding displacement signals back to the magnetic levitation device 31 to 34 and a second controlloop for compensating acceleration signals, feeding acceleration signals to the magnetic levitation devices 31 to 34 forward and restricting vibration from transmitting to the vibration resistant table 10 from the base. コントローラ5は、変位信号を磁気浮上装置31〜34にフィードバックして基礎に対する除振台10の相対位置を位置決めするための第1の制御ループと、加速度信号を補償して磁気浮上装置31〜34にフィードフォワードし、基礎から除振台10に振動が伝達するのを抑制するための第2の制御ループとを備える。 - 特許庁
In addition to this main feedback loop, the control system is provided with a loop for getting a time constant τ corresponding to a torque deviation ΔT at the timing of each control operation cycle by using a table 86 which shows the relation of the time constant τ to the torque deviation ΔT, and applying the response property 88 of the primary delay based on the time constant τ to a primary delay processor 74. このメインフィードバックループに加え、トルク偏差ΔTに対する時定数τの関係を示すテーブル86を用いて、各制御演算周期のタイミングにおけるトルク偏差ΔTに対応する時定数τを求め、その時定数τに基づく1次遅れの応答特性88を1次遅れ処理部74に適用するループが設けられる。 - 特許庁
A PLL loop by phase comparison is constituted of a phase comparator 1 for detecting the phase difference between EFM signals 4, for which analog signals read from a disk are digitized and reproducing clock PCK signals 5, a loop filter 2 for filtering-processing the detected phase difference and a control oscillator 3 for controlling the frequency, based on the output of the loop filter 2 and outputting the PCK signals 5. ディスクから読みとったアナログ信号をデジタル化したEFM信号4と再生クロックPCK信号5との位相差を検出する位相比較器1と、検出された位相差をフィルタリング処理するループフィルタ2と、このループフィルタ2の出力に基づいて周波数を制御されPCK信号5を出力する制御発振器3とで位相比較によるPLLループが構成される。 - 特許庁
Test signal transmitting power in accordance with the call connection number for radio terminals which are connected to a radio base station unit upon the loop back test is obtained at a control circuit 1, and the transmitting power TSTP is output to channel circuits used for the transmission of the loop back test signal. 制御回路1で、折り返し試験の際に当該装置に呼接続されている無線端末の呼接続数に応じた試験信号の送信電力を求め、その送信電力TSTPを、折り返し試験信号の送信に用いているチャネル回路へ出力する。 - 特許庁
The PLL circuit has a phase detector 1, a charge pump 2, a loop filter 3, and a voltage-controlled oscillator 4 which are connected in a loop, and includes a charge pump 7 for acceleration which can operate in parallel to the charge pump 2, and a control means 5 of controlling the operation timing of the charge pump 7 for acceleration. ループに接続された位相検出器1、チャージポンプ2、ループフィルタ3、電圧制御発振器4を備えた本発明のPLL回路は、チャージポンプ2と並列動作可能な加速用チャージポンプ7、加速用チャージポンプ7の動作タイミングを制御する制御手段5を備えて構成される。 - 特許庁
The core material 4 locks the filter 5 by the locking means 6 to control the attitude of the filter 5, the capture appliance 3 captures the filter 5 locked by the locking means 6, by the loop 31, and the tube body 2 retracts the filter 5 captured by the loop 31 into the tube inside by being moved to the distal end side. そして、芯材4は、係止手段6でフィルタ5を係止してフィルタ5の姿勢を制御し、捕捉具3は係止手段6に係止されたフィルタ5をループ31で捕捉し、管体2は、先端側に移動されることでループ31により捕捉されたフィルタ5を管内に引き込む。 - 特許庁
Thus, the estimation precision of the feedback gain can be improved more than that of prior arts, resulting in that the total loss amount control not in excess of a multiple of one of the open-loop gain of the closed loop can be executed optimally more than prior arts and it is possible to furthermore increase opportunities of achieving two-way simultaneous call. 故に従来例に比べて帰還利得の推定精度が向上し、その結果、閉ループの一巡利得が1倍を超えないような総損失量制御を従来以上に最適に行うことができ、双方向の同時通話を実現する機会をさらに増やすことが可能となる。 - 特許庁
In a process of shifting from a transient state to a stationary state of phase drawing, variation of average voltage output of the loop filter 12 which occurs in switching loop bands is reduced and the lockup time is shortened by performing control of stopping the sub-buffer circuit 21 after stopping the sub-buffer circuit 7. 位相引き込みの過渡状態から定常状態へ移行する過程で、サブバッファ回路7を停止した後、サブバッファ回路21を停止させる制御を行うことで、ループ帯域の切替え時に起こるループフィルタ12の平均電圧出力の変化量を小さくして、ロックアップタイムを短縮する。 - 特許庁
An output signal S11 outputted from an FW filter 61 of a judgment feedback type equalizer 51 and a feedback signal S12 outputted from an FB filter 64 are monitored by a loopcontrol circuit 54, and a feedback loop including the FB filter 64 is ON-OFF controlled based on the monitoring result. 判定帰還型等化器51のFWフィルタ61から出力される出力信号S11とFBフィルタ64から出力される帰還信号S12をループ制御回路54にて監視し、その監視結果に基づいてFBフィルタ64を含む帰還ループをオンオフ制御するようにした。 - 特許庁
By reducing at least one of a loop formation amount by the skew correcting means 8, 21 and a driving time of a driving means for driving the separating means 5A by a control means 50, the noise of the driving means and the noise in forming the loop can be inhibited. そして、制御手段50により斜行補正手段8,21によるループ形成量及び分離手段5Aを駆動する駆動手段の駆動時間の少なくとも一方を減少させることにより、駆動手段の騒音及びループ形成時における異音の発生を抑えるようにする。 - 特許庁
This electric power supply device is provided with a loop shaped wiring coming from a positive electrode of a battery and returning to the positive electrode with the same electric potential, a load receiving supply of electric power from a control unit connected to the wiring, and a junction circuit cutting off a short-circuited load from the loop shaped wiring when the load circuit is short-circuited. バッテリの正極から出て正極に戻る同電位のループ状配線と、当該配線に接続された制御ユニットから電力の供給を受ける負荷と、負荷回路のショート時に当該ショート負荷をループ状配線から切り放す中継回路を有する。 - 特許庁
The leased line terminating device on the control side and that on the controlled side individually detect whether a leased line is faulty or not during the remote loop back test and are individually restored to the normal state from the remote loop state at the time of occurrence of a fault of the leased line. リモート・ループバック試験を行っている間、制御側の専用回線終端装置及び被制御側の専用終端装置が個別に専用回線の障害の有無を検出し、専用回生の障害が生じたときには、個別にリモート・ループ中の状態から通常状態に復帰する。 - 特許庁
A feedback loop is branched and input to a variable-frequency down-converter section and a detector, whose detector output is processed by a DSP in a base band circuit and analyzed as a spectrum to automatically control a parameter which can not be compensated by a Digital Pre-Distortion distortion compensating Loop. フィードバック・ループを分岐して周波数可変のダウンコンバータ部および検波器に入力し、その検波器出力をベースバンド回路内のDSPにて処理しスペクトラムとして解析することでDigital Pre−Distortion歪み補償Loopでは補償しきれないパラメータを自動で制御する。 - 特許庁
The method includes a step for using an output signal of a loop filter LF in a controlloop for timing recovery, a step for generating an average timing error value from filtered timing error signals, and a step for accumulating changes of the average timing error value in adjacent blocks of samples exceeding a first threshold. タイミング回復のために制御ループ中のループフィルタLFの出力信号を使用するステップと、前記フィルタ処理後のタイミング誤差信号から平均タイミング誤差値を生成するステップと、第1の閾値を超えるサンプルの隣接するブロックの平均タイミング誤差値の変化を累積するステップとを含む。 - 特許庁
When the transmitter is operated from off to on (at the time of initial operation in a cartesian loop), a phase control part 9 controls a phase shift amount at the circuit 11 but when the initial operation of the cartesian loop is completed, the part 9 controls a phase shift amount at the circuit 8. 位相制御部9は、送信機がオフからオンに操作されたとき(カーテシアンループにおける初期動作時)は位相調整回路11における位相シフト量の制御を行い、カーテシアンループの初期動作が完了したときは、位相調整回路8における位相シフト量の制御を行う。 - 特許庁