「Front-engine」を含む例文一覧(1461)

<前へ 1 2 .... 20 21 22 23 24 25 26 27 28 29 30 次へ>
  • It is devised not to splash water on a diaphragm actuator 1 by arranging a reservoir tank T for cooling water in front of the actuator 1 to be arranged on a side part (left side part) on which air containing droplets becomes easy to flow on the opposite side of an arranging part of the air suction port Ea of the engine room.
    また、エンジンルームの吸気口Eaの配置部とは反対側の、水滴を含んだ空気が流れ易くなる側部(左側部)に配置するダイヤフラムアクチュエータ1の前方に冷却水用リザーブタンクTを配置し、ダイヤフラムアクチュエータ1に水がかかりにくくなるようにする。 - 特許庁
  • The engine E that can reduce pumping loss by cylinder cut-off is connected to a front wheel Wf through a first motor generator MG1, an oil pump 13, a first clutch 14, a belt-type continuously variable transmission M and a second clutch 20, and a second motor generator MG2 is connected to a rear wheel Wr.
    休筒によりポンピングロスを低減可能なエンジンEを第1モータ・ジェネレータMG1、オイルポンプ13、第1クラッチ14、ベルト式無段変速機Mおよび第2クラッチ20を介して前輪Wfに接続するとともに、第2モータ・ジェネレータMG2を後輪Wrに接続する。 - 特許庁
  • The circumference of the exhaust pipe 32 is covered with a ventilation pipe 38, and a part of cooling air generated by a cooling fan 39 of the engine 3 and flowing from the rear to the front is introduced into the ventilation pipe 38 and flows from the start end side to the terminal side to cool the exhaust pipe 32.
    エキゾーストパイプ32の周囲を通風パイプ38で被覆して、エンジン3の冷却ファン39により生起され後方から前方に流れる冷却風の一部を通風パイプ38に導入して、始端側から終端側に流しエキゾーストパイプ32を冷却する。 - 特許庁
  • To provide a forward part structure of a vehicle having an electric fan at the front of an engine in the vehicle direction which can prevent the electric motor part of the electric fan from impeding the deformation of the forward part of the vehicle at the time of a head-on collision, and which can prevent the occurrence of a secondary disaster caused by the electric motor part.
    エンジンの車両前方に電動ファンの配設された車両の前部構造において、該電動ファンの電動機部分によって正面衝突時の車両前部の変形が阻害されるのを防止するとともに、該電動機部分によって2次的な災害が発生するのを防止する。 - 特許庁
  • This configuration allows little transmission of vibration and noise occurring inside the cylinder 1 by compressing action to the front side plate 6, the back side plate 7, and the high pressure case 13, causing no resonance of vibration and noise occurring in the compressor with engine components and having no influence on the inside of the cabin.
    これによって、シリンダ1内の圧縮作用により発生する振動・騒音が、前部側板6、後部側板7、高圧ケース13に伝達されにくくしなるので、圧縮機で発生する振動・騒音によるエンジン部品との共振や車室内騒音への影響はなくなる。 - 特許庁
  • The main ECU 20 stops fuel supply to the engine 14 by interrupting the front clutches 38a and 38b and controls the motor travel mode for driving the rear wheels 26b with the second motor 18 while dividing into first travel mode and second travel mode.
    メインECU20は、フロントクラッチ38a、38bを遮断してエンジン14への燃料供給を停止するとともに第2モータ18により後輪26bを駆動して走行する電動走行モードを第1走行モードおよび第2走行モードの2つに分けて制御を行う。 - 特許庁
  • The driving force transmission has a clutch mechanism for transmitting a driving force transmitted from an engine to one wheel of front and rear wheels to the other wheel, the magnet coil for controlling the transmission torque amount of the clutch mechanism, and a temperature sensor for detecting temperature of the oil for keeping the function of the clutch mechanism.
    駆動力伝達装置は、エンジンから前・後一方の車輪に伝達される駆動力を他方の車輪に伝達するクラッチ機構と、クラッチ機構の伝達トルク量を制御する電磁コイルと、クラッチ機構の機能を保持するオイルの温度を検出する温度センサとを有する。 - 特許庁
  • The group of front stroke cylinders is a group of cylinders which can perform fuel injection of quantity corresponding to an injection quantity command value at the starting (an amount of fuel injection required for starting the engine 1) until the first half of a valve-opening period of a first intake valve 13 after determining a crank angle at the starting.
    表行程気筒群とは、始動時のクランク角の判別後における最初の吸気バルブ13の開弁期間前期までに始動時噴射量指令値(エンジン1の始動に必要な燃料噴射量)に対応する量の燃料噴射を行うことの可能な気筒群のことである。 - 特許庁
  • A car body frame is bridged between a pair of right and left crawler type running parts, an engine is loaded in the front part of the car body frame, a mission part is disposed in the back part of the car body frame, and an HST for turning and an HST for rectilinear propagation are integrally interlocked and connected to the transmission part.
    左右一対のクローラ式の走行部間に車体フレームを架設し、同車体フレームの前部にエンジンを搭載すると共に、同車体フレームの後部にミッション部を配設し、同ミッション部に旋回用HSTと直進用HSTとをそれぞれ一体的に連動連設した。 - 特許庁
  • The tower bar 37 comprises: a tower bar body member 45 being disposed ahead of the damper base parts 31 and the engine 16 in the vehicle and connecting the left and right upper members 35; and a support part 46 being continuous with the tower bar body member 45 and connecting these upper members 35 and a damper base front wall 44.
    タワーバー37は、ダンパーベース部31及びエンジン16より車両前方に配置され、左右のアッパーメンバー35を連結しているタワーバー本体部材45と、タワーバー本体部材45に連なり、アッパーメンバー35とダンパーベース前壁44とを連結する支持部46と、からなる。 - 特許庁
  • A sound absorbing material 15 is fixed to the inner side face of a car body side bulkhead 14 located in the front section in a car cabin to absorb the noise from an engine room 12, and this sound absorbing material 15 is made of material effective for sound absorption and the sound insulation like a face duct 17.
    車室内前部に位置する車体側の隔壁14の内側面には、エンジンルーム12からの騒音を吸音することを目的として吸音材15が固着されており、この吸音材15は、フェイスダクト17と同様に吸音、遮音効果を有する材質で構成されている。 - 特許庁
  • To realize compact lengths in the front and the rear of a vehicle body to improve the maintenance property by making weight balance of a four cycle multiple cylinder engine mounted on a motor-bicycle optimum and relating the weight balance to the arrangement of an intermediate shaft, an output shaft, and a multistage transmission mechanism inside a transmission.
    本発明は、自動二輪車に搭載する4サイクル多気筒エンジンの重量バランスを最適に又変速機内部の中間軸、出力軸、多段変速機構等の配置と関連を持たせ車体の前後長のコンパクト化をはかりよりメンテナンス性を向上させたことを目的としている。 - 特許庁
  • In this mowing machine a mower 4 is installed between a front wheel 1 and lateral rear wheels 2, a driver's sheet is installed above the mower 4, speed change devices 6 installed to the aforesaid lateral rear wheels through a transmission system are laterally arranged and an engine 1 is installed above the space between the aforesaid lateral rear wheels.
    前輪1と左右の後輪2との前後間にモーア4を配置し、このモーア4の上方に運転座席を配置し、前記左右の後輪2それぞれへの伝動系に介装する変速装置6を左右に振り分け配置し、前記左右の後輪2間の上方にエンジン7を配置する。 - 特許庁
  • On passing the curve in front, a recommended speed capable of smoothly passing is detected based in a curvature of the curve, and on applying an engine brake with a lower gear change stage than the present one, a deceleration possible speed capable of decelerating the recommended speed at the curve is computed based on a distance as far as the curve.
    そして、前方のカーブを通過する際に円滑に通過し得る推奨速度をカーブの曲率に基づき検出し、現在よりも低い変速段にてエンジンブレーキを掛けた際に、該カーブにて推奨速度まで減速し得る減速可能速度を、カーブまでの距離に基づき算出する。 - 特許庁
  • The drive unit of a hybrid vehicle comprises a speed change input shaft 31 being coupled with an engine 20, and a speed change output shaft 32 being coupled with a drive motor 21 and the speed change input shaft 31 through a speed change gear 26 and transmitting power to the front wheel 13.
    ハイブリッド車両の駆動装置は、エンジン20に連結される変速入力軸31と、駆動用モータ21に連結されるとともに変速機26を介して変速入力軸31に連結され、前輪13に動力を伝達する変速出力軸32とを有する。 - 特許庁
  • A passage-shaped duct part 22 formed by bending the side edge in a cylindrical shape, is formed in both side parts of a heat shield 21 for covering a front face of the catalytic converter 9, and its upper end 22a is opened in the engine room 2, and the lower end 22b is opened in a height position under the floor of the car body.
    触媒コンバータ9の前面を覆う遮熱板21の両側部に、側縁を筒状に折り曲げてなる通路状のダクト部22が形成されており、その上端22aがエンジンルーム2内に開口し、下端22bが車体床下の高さ位置で開口する。 - 特許庁
  • To provide an arrangement structure of a vehicular air conditioner capable of satisfying both needs of a request for disposing an engine rearward and a request for rounding a front window member by arranging an air- conditioning duct connected to an air-conditioning unit at the back of an instrument panel member to blow air-conditioning air into a cabin.
    インパネメンバの後方に空調ユニットと接続されて空調風を車室内に吹出す空調ダクトを配設することで、エンジンの後退配設要求とフロントウインド部材のラウンド化要求との双方のニーズを満たすことができる車両用空調装置の配設構造の提供を目的とする。 - 特許庁
  • To obtain the optimum weight distribution of front and rear wheels, and to suppress direct transmission of a shock in a head-on collision of a vehicle to a space in a cabin, in a vehicle such as an electric car on which any large equipment other than a battery such as an engine and a fuel tank is not mounted.
    エンジンや燃料タンクなどといったバッテリ以外の大型機器が搭載されない電気自動車等の車両において、前後輪の最適な重量配分を得るとともに、車両前突時にその衝撃が車室内空間に直接伝達することを抑制する。 - 特許庁
  • The engine room front end upper part member 25 is provided with: a main body part 27 extending in a vehicle width direction at a position above the radiator core support upper 11; and leg parts 29 downwardly extending from both ends in a vehicle width direction of the main body part 27 and having a lower part joined/fixed to the radiator core support upper 11.
    エンジンルーム前端上部部材25は、ラジエータコアサポートアッパ11の上方位置にて車幅方向に延びる主体部27と、主体部27の車幅方向両端から下方に延びその下部をラジエータコアサポートアッパ11に接合固定する脚部29とを備える。 - 特許庁
  • The hollow aerofoil 12 of a gas turbine engine has the walls of positive and negative pressure surfaces apart in a width direction, and these walls are connected into one body at the front and rear edges 20 and 22 apart in the blade chord direction of the aerofoil 12, to extend in a lengthwise direction from a root to a tip.
    ガスタービンエンジンの中空エーロフォイル12が、幅方向に離隔した正圧面及び負圧面の壁を有し、これらの壁がエーロフォイル12の翼弦方向に離隔した前縁及び後縁(20、22)で一つにつながっていて、根元から先端まで縦方向に延在する。 - 特許庁
  • This tire warmer A guides and retains engine exhaust heat collected by providing a heat-collecting cover 1 on the rear side of a radiator 10 to the inside of wheel wells H, H via a hollow part of a bulkhead upper side frame 12d (vehicle body skeleton) in a front part of the automobile M.
    本発明のタイヤ昇温装置Aは、ラジエータ10の後方に集熱カバー1を設けて集熱したエンジン排熱を、自動車Mの前部におけるバルクヘッドアッパサイドフレーム12d(車体骨格)の中空部を介してホイールハウスH,H内に導いて滞留させることを特徴とする。 - 特許庁
  • A camera system 1 which obtains a series of picked-up images through continuous shooting stores RAW images output in sequence from an imaging unit 15 in a DRAM 4b of a front engine 4 and also performs correction processing, and then outputs the RAW image having been corrected to back engines 5a and 5b alternately.
    連写により一連の撮像画像を得るカメラシステム1では、撮像部15から順次に出力されるRAW画像をフロントエンジン4のDRAM4bに記憶させるとともに補正処理を施し、補正処理済みのRAW画像を各バックエンジン5a、5bに交互に出力する。 - 特許庁
  • To suppress or prevent unexpected increase of friction loss by suppressing oil leaked from support parts of front-most ends of cam shafts 8, 9 wetting a timing chain 5, in an engine wherein the cam shafts 8, 9 are rotatably supported by a cam housing 3 mounted on a cylinder head 2.
    シリンダヘッド2上に搭載されるカムハウジング3にカムシャフト8,9が回転自在に支持されるエンジンにおいて、カムシャフト8,9の最前端の支持部分から漏洩するオイルが、タイミングチェーン5にかかりにくくさせて、フリクションロスの想定外の増大を抑制または防止可能とする。 - 特許庁
  • The fuel nozzle 10 comprises a fuel injector 14 for injecting fuel into an engine combustion chamber 12, and a plurality of rows 16 and 18 of holes 20 that surround the fuel injector 14 and remove recirculation of hot gas product to the above part of the front surface 22 of the fuel nozzle 10.
    燃料ノズル10は、エンジンの燃焼室12内に燃料を噴射する燃料噴射器14と、燃料噴射器14を取り囲むとともに燃料ノズル10の正面22上への高温ガス生成物の再循環を除去する孔20の複数の列16および18とを有する。 - 特許庁
  • To improve the operating efficiency when escape operations from an unrunnable state, etc., caused by a remarkable difference in resistance to left and right driving front wheels during braking operations of a machine body without applying overstrain to an engine while improving the comfortableness in a boarding driving part.
    搭乗運転部での居住性の向上を図りながら、エンジンに無理を掛けることのない機体の制動操作や、左右の駆動前輪に対する抵抗が著しく異なることに起因した走行不能状態などからの脱出操作を行う際の操作性の向上を図れるようにする。 - 特許庁
  • To provide a vehicle front end structure which is applicable to a light vehicle of a displacement of ≤660 cc, or a vehicle having a relatively large cargo room space such as a van and a truck among small-size vehicles of a displacement of about 1,000 cc with an engine mounted on the lower side or the rear side of a cabin.
    エンジンが室内の下方側又は後方側に搭載され、かつ、排気量が660cc以下の軽自動車や排気量が1000cc程度の小型自動車のうちバンやトラック等の荷室スペースが比較的大きい車両に適用した車両前端構造を提供する。 - 特許庁
  • When a driver issues a request command for maintaining four-wheel drive or when the road condition of the vehicle changes, a control logic 200 of the 4WDCU 6 maintains a four-wheel drive mode in which the rear wheels are driven by the motor 5 and the front wheels are driven by an internal combustion engine 1.
    4WDCU6の制御ロジック200は、運転者から4駆持続の持続要求指令がある場合、或いは車両の走行路状態に変化が生じる場合には、電動機5により後輪を駆動し、内燃機関1により前輪を駆動する4駆モードを持続する。 - 特許庁
  • This traveling controller is constituted so that an engine control unit 20 and a throttle actuator 2a, a rotation driving force distributing device 10 for performing transmission torque distribution control to front wheels and rear wheels, four-wheel driving control unit 30 and a traveling stabilization control unit 40 are contained in a four-wheel drive car 1.
    4輪駆動車1において、エンジンコントロールユニット20およびスロットルアクチュエータ2aと、前輪および後輪への伝達トルク分配制御を行う回転駆動力分配装置10と、4輪駆動コントロールユニット30と、走行安定コントロールユニット40とを備えて走行制御装置が構成される。 - 特許庁
  • A box mounting part 22 of a driver's seat pedestal 25 provided to cover the front part of an engine 7 is provided with an inspection port 22D positioned in the vicinity of an alternator 9, and the inspection port 22D is covered with an inspection cover 30 removably fitted to the box mounting part 22.
    エンジン7の前側部位を覆うように設けられた運転席台座25のボックス取付部22には、オルタネータ9の近傍に位置して点検口22Dを設け、この点検口22Dは、ボックス取付部22に着脱可能に取付けられる点検カバー30によって覆う構成とする。 - 特許庁
  • This fan case 22 for a turbo fan engine 10 comprising a fan 12 including plural fan moving blades 18 installed on a rotor disc 14, and a decoupler 44 broken corresponding to a specified load substantially includes a circular shell 46, and the shell 46 comprises a front part 48, a middle part 50, and a rear part 52.
    ロータディスク(14)に装着した複数のファン動翼(18)を含むファン(12)と、所定荷重に応じて破損するデカプラ(44)とを有するターボファンエンジン(10)用のファンケース(22)が、実質的に環状の殻(46)を含み、この殻は前部(48)と中間部(50)と後部(52)とを有する。 - 特許庁
  • For a vehicle of a structure in which the volume of the inside of the air cleaner is very small, a generator having a duct is fitted to the right front of an outside air inlet, whereby air mixed with ozone required by an engine is sucked in the interior of a cylinder without large attenuation of ozone gas.
    エアークリーナー内部の体積が非常に狭い作りの車輌に対しては、外気取り入れ口直前にダクトを装着した発生機を取り付けることにより、オゾンガスの大きな減衰もなくエンジンが必要とするオゾンとの混合空気がシリンダー内部に吸入されるのである。 - 特許庁
  • To arrange an electric storage device in a position which hardly receives an influence of heat from an engine or a motor, and to support the electric storage device so as not to have an influence on shock absorbing performance in a head-on collision of a vehicle as much as possible when arranging the electric storage device in front of the vehicle.
    蓄電装置を車両の前部に配設する場合に、蓄電装置を、エンジン又はモータからの熱の影響を受け難いような位置に配設しかつ車両の前面衝突時における衝撃吸収性能に出来る限り影響を与えないように支持する。 - 特許庁
  • To prevent vibration and noise occurring in a cylinder of a compressor due to compressing action from being transmitted to a front side plate, a back side plate, and a high pressure case, to prevent resonance of the vibration and noise with engine components causing allophone or uncomfortable sound in the cabin of a vehicle through transmission via an air conditioner.
    圧縮機のシリンダ内の圧縮作用により発生する振動・騒音が、前部側板、後部側板、高圧ケースに伝達し、その振動・騒音がエンジン部品と共振し異音の原因になったり、また空調装置を伝達し車室内で不快音として聞こえないようにすること。 - 特許庁
  • This power unit 3 is supported by three points on a sub-frame 2 by a front engine mount 12 having a main mount part 23 formed in the vicinity of a vertical face including a roll shaft R of the power unit 3 and sub-mount parts 24 formed on both sides across the vertical face including the roll shaft R.
    パワーユニット3のロール軸Rを含む鉛直面近傍に形成された主マウント部23と、ロール軸Rを含む鉛直面を挟んだ両側に形成された副マウント部24とを有するフロントエンジンマウント12により、パワーユニット3をサブフレーム2上の3点おいて支持する。 - 特許庁
  • To provide a travel controller for a vehicle capable of such four wheel driving as one of front and rear wheels is driven through an engine and the other is driven through a motor/generator in which the four wheel drive function can be exhibited surely under a situation requiring effective utilization thereof.
    本発明の目的は、前輪又は後輪の一方をエンジンで駆動すると共に、他方をモータ/ジェネレータで駆動する四輪駆動可能な車両において、四輪駆動機能を有効に活用したい状況で確実に機能させることのできる車両用走行制御装置を提供すること。 - 特許庁
  • A fuel supply system 10 of an engine comprises the feed pump 100 installed in a fuel tank to feed fuel under low discharge pressure, high pressure fuel pumps 200 and 300, and pulsation dampers 220 and 320 installed in front of an inlet of the high pressure pumps 200 and 300.
    エンジンの燃料供給システム10は、燃料タンクに設けられ、低圧の吐出圧で燃料を供給するフィードポンプ100と、高圧燃料ポンプ200,300と、高圧燃料ポンプ200,300の入り口の手前に設けられたパルセーションダンパー220,320とを含む。 - 特許庁
  • This oil pan structure has a projecting body 12 for installing an engine auxiliary machine that is disposed on a surface positioned in the front direction of the vehicle of the oil pan 4 and supports the lower part of a compressor 7, and a guiding rib 18 having a tilting surface from the lower part of the projecting body 12 to the lower surface of the oil pan 4 in the side surface view.
    オイルパン4の車両前方向に位置する面に設けられ、コンプレッサ7の下部を支持するエンジン補機設置用の突起体12を備え、側面視において、突起体12の下部とオイルパン4の下面とにかけて、傾斜面を有する案内リブ18を設ける構造とした。 - 特許庁
  • In the engine having the water pump mounted at the front end, the cooling water path is integrally cast and formed inside a crank case, which is connected to the cooling water outlet of the water pump and connected to the cooling portion while extending to the axial center of the crank.
    エンジン前端部にウォータポンプを装着してなるエンジンにおいて、クランクケースの内部に、前記ウォータポンプの冷却水出口に接続されるとともにクランク軸心方向に延びて冷却部に接続される冷却水通路を一体鋳造して形成されたことを特徴とする。 - 特許庁
  • To provide an exhaust emission control device of an internal combustion engine which can prevent damage to a NOx occlusion catalyst due to an excessive temperature rise by suppressing the excessive temperature rise resulting from rapid combustion of HC at a front stage catalyst at S purge, and achieve an excellent NOx purification rate by preventing the reduction and delay of arriving HC to the NOx occlusion catalyst resulting from HC adsorption by the front stage catalyst at NOx purge.
    Sパージ時の前段触媒でのHCの急激な燃焼による過昇温を抑制し、もって過昇温に起因するNOx吸蔵触媒のダメージを未然に防止できると共に、NOxパージ時には前段触媒でのHC吸着に起因するNOx吸蔵触媒への到達HCの減少や遅れを防止し、これにより良好なNOx浄化率を実現できる内燃機関の排気浄化装置を提供する。 - 特許庁
  • A camera system 1A which obtains a series of picked-up images through continuous shooting makes shading corrections etc. of RAW image data output in sequence from an imaging unit 15 by a front engine 4, and outputs the RAW image data having been corrected to back engines 5a and 5b alternately together with photography order information.
    連写により一連の撮像画像を得るカメラシステム1Aでは、撮像部15から順次に出力されるRAW画像データに対してフロントエンジン4でシェーディング補正等を施し、補正処理済みのRAW画像データを撮影順番情報とともに各バックエンジン5a、5bに交互に出力する。 - 特許庁
  • Fuel piping 190 and 12 lead fuel to a low pressure fuel supply system 11 and a high pressure fuel supply system 12 for injecting fuel to the engine 10 arranged in a vehicle front zone 600F respectively from a fuel tank 165 arranged in a vehicle rear zone 600R.
    燃料配管190および192は、車両の後方領域600Rに配置された燃料タンク165から、車両の前方領域600Fに配置されたエンジン10に燃料を噴射するための低圧燃料供給系11および高圧燃料供給系12のそれぞれへ燃料を導く。 - 特許庁
  • The lockup clutch 3 includes an outer hub 3a extending toward the lockup damper 4 while supporting one friction engagement element 3c out of a pair of friction engagement elements 3c and 3d capable of engagement, and an inner hub 3b extending toward an engine (front cover 6) while supporting the other friction engagement element 3d.
    ロックアップクラッチ3は、係合自在な一対の摩擦係合要素3c,3dのうち一方の摩擦係合要素3cを支持しロックアップダンパ4側に向って延在するアウターハブ3aと、他方の摩擦係合要素3dを支持しエンジン側(フロントカバー6側)に向って延在するインナーハブ3bと、を備える。 - 特許庁
  • Collection efficiency of particulate in the diesel particulate filter 4 is improved by changing a domain of exhaust gas flowing in the diesel particulate filter 4 according to engine operation conditions by an exhaust gas flowing in domain control means 5 arranged in a front stage of the particulate filter 4.
    エンジンの運転条件に応じてディーゼルパティキュレートフィルタ4に流入する排ガスの領域をディーゼルパティキュレートフィルタ4の前段に配した排ガス流入領域制御手段5によって変化させることで、ディーゼルパティキュレートフィルタ4におけるパティキュレートの捕集効率を向上させる排ガス浄化装置が得られる。 - 特許庁
  • To suitably supply a reducing agent to a particulate filter in the case a front stage catalyst having an oxidation function, an occlusion reduction type NOx catalyst, and the particulate filter carrying a catalyst having an oxidation function are disposed in an exhaust passage of an internal combustion engine in order from the upstream side.
    本発明は、内燃機関の排気通路に酸化機能を有する前段触媒および吸蔵還元型NOx触媒、酸化機能を有する触媒を担持したパティキュレートフィルタが上流側から順に配置されている場合において、より好適にパティキュレートフィルタに還元剤を供給することを目的とする。 - 特許庁
  • In a hybrid vehicle 1 where a transmission 14 is connected through a first clutch 13 to an internal combustion engine 11 and a first motor 12 serially connected to front wheels Wf and Wf, a second motor 16 configuring a three-phase brushless DC motor is connected through a second clutch 15 to the transmission 14.
    前輪Wf,Wfに直列に直結した内燃機関11及び第1モータ12に第1クラッチ13を介してトランスミッション14を接続してなるハイブリッド車両1において、3相のブラシレスDCモータをなす第2モータ16を第2クラッチ15を介してトランスミッション14に接続した。 - 特許庁
  • In a front engine 4 of a camera system 1A, reduced-size image generation processing for generating a reduced-size image, by reducing a captured image output from an image capturing portion 15 is executed by an image reducing portion 410 as hardware processing which is performed in parallel with storage processing for storing the captured image data output from the image capturing portion 15 in DRAM 4b.
    カメラシステム1Aにおけるフロントエンジン4では、撮像部15から出力される撮影画像データをDRAM4bに記憶させる記憶処理と並行して行うハードウェア処理として、撮像部15から出力される撮影画像を縮小し縮小画像を生成する処理を画像縮小部410で実行する。 - 特許庁
  • A correction face 49 crossing the axial line L1 substantially orthogonally is provided on a front face of a cylinder head 15, and a mounting angle correction part 53 for correcting a mounting angle of the mounting part 37 for the internal combustion engine 11 by coming into contact with the correction face 49 is provided on the pulley bracket 24 when mounting the mounting part 37.
    さらに、シリンダヘッド15の前面に前記軸線L1に略直交する矯正面49を設けるとともに、プーリブラケット24には、取付部37の取付けに際し、矯正面49に接触することにより取付部37の内燃機関11に対する取付角度を矯正する取付角度矯正部53を設ける。 - 特許庁
  • The particulates with a decreased ignition temperature collected in the filter are burned rapidly by supplying the electric power of at least 2 kw to the electric heating element of the filter 30 for 10 to 80 seconds at the desired timing when the pressure difference between the front/rear parts of the filter 30 arranged in the exhaust pipe 28 is increased by the operation of an engine main body 10.
    エンジン本体10の運転により、排気管28に設置したフィルタ30の前後の差圧が高まった所望時期に、フィルタ30の電気加熱素子に、少なくとも2kWの電力を10〜80秒間供給して、フィルタに捕集された着火温度の低下した微粒子を急速燃焼させる。 - 特許庁
  • A motorcycle 1 comprises the belt continuously variable transmission 30 disposed at the front of a rear wheel 4 together with an engine 20, the transmission case 50 for storing the continuously variable transmission 30, an intake duct 75 for introducing the outside air into the transmission case 50, and an exhaust duct 70 for discharging the air in the transmission case 50.
    自動二輪車1は、エンジン20とともに後輪4より前側に配置されたベルト式の無段変速機30と、無段変速機30を収容する変速機ケース50と、外気を前記変速機ケース50内に導入する吸気ダクト75と、変速機ケース50内の空気を排出する排気ダクト70とを備える。 - 特許庁
  • A display board 4 having an engine oil mark 14 that is a light transmissible warning display part is disposed in the front of an illumination chamber 3 formed by partitioning a case 1 with a partition 2, while a light-emitting diode 12 that emits red light and electrically connected to a printed circuit board 5 is provided in the rear of the illumination chamber 3.
    ケース1を仕切壁2によって区画して形成した灯室3の前方に光透過性のウォーニング表示部であるエンジンオイル記号14を設けた表示板4を配設し、灯室3の後方にプリント配線板5と電気的に接続された発光色が赤色の発光ダイオード12を設ける。 - 特許庁
<前へ 1 2 .... 20 21 22 23 24 25 26 27 28 29 30 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.