A tub (21) for introducing the rain water is connected to the storage tank (11), and a water pipe (12) for supplying the purified water in the storage tank (11), which is purified by using the discharge unit (62), to a predetermined portion is also connected to the storage tank (11). 貯留タンク(11)には、雨水を導く樋(21)が接続されると共に、放電ユニット(62)によって浄化された貯留タンク(11)の浄化水を所定箇所に供給する送水管(12)が接続されている。 - 特許庁
Alternatively, when the power consumption of the liquid crystal unit 254 is large, a translate circuit for translating the power supply of 34V to the power supply of 12V is provided and the liquid crystal unit 25 is controlled using the translated power supply of 12V. 一方、液晶ユニット254の消費電力が大きい時には、34Vの電源を12Vの電源に変換する変換回路を設け、変換した12Vの電源を用いて液晶ユニット25を制御する。 - 特許庁
A tracer roller 22 of the means 17 is abutted to the bottom surface of a work W, and the position of a cutter 15 for machining installed in the machining unit 12 is restricted, and the machining is conducted using the tracer roller 22 as the reference. 倣い手段17の倣いローラ22をワークWの下端面に当接し、切削加工ユニット12に備えた切削用のカッター15の位置を規制し、倣いローラ22を基準として切削加工を行う。 - 特許庁
To disallow a third person to impersonate a recipient and to prove that an article is delivered when the article of commerce which is ordered without meeting by using a network, etc. is delivered. ネットワークなどを使用して非対面で発注された商取引での物品の引き渡しに際して、受取人への他人のなりすましを許さず、且つ、商品の引き渡しを行ったことを証明できるようにする。 - 特許庁
After solidifying the lining concrete, a water cutoff seal 11 is embedded in the joint 5, the placing of the lining concrete is resumed, and another one ring-shaped steel plate 2a is fixed to the lining body 1a by using the anchor bolt 8. 覆工コンクリートが固化した後、打継ぎ目5に止水シール11を埋め込み、再度覆工コンクリートの打設を再開し、もう一方のリング状鋼板2aをアンカーボルト8を用いて覆工体1aに固定する。 - 特許庁
Using a projection distribution parameter which is smaller when projections are located in eccenticity toward one side and is greater when they are uniformly distributed more with regularity, the projection distribution parameter is set over 0.5 for making uniform the stress distribution. また、突起が一方に片寄っているほど小さく、規則性を持って均一に分布しているほど大きくなる突起分布パラメータを用い、応力分布の均一化を狙って突起分布パラメータは0.5以上と設定した。 - 特許庁
Then, the identical substrate (S3) is exposed to the test structure of a second set identical to the first set during a second test exposure sequence using a second course which is equivalent to the first course but in which movement is caused in a reverse direction state. つぎに第1セットと同一の、第2セットのテスト構造を、第1コースと等しいが逆方向状態で移動させる第2コースを使って、第2テスト露光シーケンスの間、同一基板上に露光する(S3)。 - 特許庁
While a work 15 is supported in the middle layer of a sealed processing tank 21, the heating medium is accumulated in the lower layer and it is heated by a heater 24 to boil and evaporate it, thereby heating the work 15 by using the steam. 密閉可能な処理槽21の中層部分にワーク15を支持し、下層部分に熱媒体を溜めて加熱ヒーター24によって加熱することにより沸騰蒸発させて、蒸気によってワーク15を加熱する。 - 特許庁
To provide a portable binocular microscope by which the recording and the simultaneous observation of an image are easily executed even through it is small- sized and is light in weight and which is carried out and used to/at outdoors and to provide an image pickup method using it. 小型軽量であっても画像の記録や同時観察などを簡便に行うことができ、野外に持ち出して使用できるような携帯用の双眼顕微鏡とそれを用いた撮像方法を提供する。 - 特許庁
To construct a computationally efficient hash function that is indifferentiable from a random oracle even when it is constructed by using an ideal compression function in which unidirectionality is broken. 一方向性が破られた理想的な圧縮関数を用いて構成した場合であっても、ランダムオラクルと強識別不可能であるハッシュ関数であって、計算効率がよいハッシュ関数を構成することを目的とする。 - 特許庁
During the shifting from a lean-burn mode to a rich-burn mode, the weight of oxygen inside a cylinder is computed (S20), an excess air ratio is computed by using the weight of oxygen inside the cylinder (S30), and a rate of combustion is computed (S40). リーン燃焼状態からリッチ燃焼状態への切り替え中に、筒内の酸素重量を算出し(S20)、それを用いて空気過剰率を算出し(S30)、さらに燃焼率を算出する(S40)。 - 特許庁
The lubricant G which is obtained by forming base oil into a gel by using an amino-acid system compound or a benzylidene sorbitol dielectric is arranged in an internal space of the bearing which is surrounded by the inner ring 1, the outer ring 2, and the sealing devices 5, 5. 内輪1と外輪2と密封装置5,5とで囲まれた軸受内部空間内には、アミノ酸系化合物又はベンジリデンソルビトール誘導体で基油をゲル化してなる潤滑剤Gが配されている。 - 特許庁
When the image of a manuscript conveyed is read by using CIS 50, the manuscript is irradiated with light by an LED array 52 provided in the CIS 50, and the reflected light from the manuscript is received by a line sensor 54. 搬送されてくる原稿の画像を、CIS50を用いて読み取る場合、CIS50に設けられたLEDアレイ52によって原稿に光を照射し、原稿からの反射光をラインセンサ54にて受光する。 - 特許庁
After a wiring trench pattern is formed in the hard mask, etching is performed from the top of the wiring layer insulating film 34 up to the midpoint of the via layer insulating film 31 by using the resist pattern as a mask, and a via hole 42 is formed halfway of the whole depth. ハードマスクに配線溝パターンを形成後、レジストパターンをマスクとして配線層絶縁膜34の上面からビア層絶縁膜31の中間までエッチングし、ビアホール42を途中の深さまで開口する。 - 特許庁
In an activation step until a driving pulley model 31 is rotated and driven and a target rotating speed is achieved by using the vibration analysis model, a simulated condition is used for applying a predetermined angular speed to the driven pulley models 32, 33, 34. 振動解析モデルにより駆動プーリモデル31を回転駆動させて目標回転数とするまでの立ち上げステップでは、各従動プーリモデル32,33,34に所定の角速度を付与する模擬条件が用いられる。 - 特許庁
Then, the conveyed liquid crystal substrate is turned in about 90° or the conveying direction is changed by using a liquid crystal substrate unit, similarly to the first side face cleaning stage, residual liquid crystal on the other two side faces is removed. 次いで液晶基板回転装置で搬送中の液晶基板をほぼ90度回転または搬送方向を変換して、第1側面洗浄ステージと同様に他の2側面の残査液晶を除去する。 - 特許庁
When using it, the sliding door 4A is opened, the fan heater 3 can be used, and when it is not in use, the sliding door 4A is closed to completely hide the fan heater 3 and make it invisible directly from the outside. 使用時には引き戸4Aを開けて温風機3を利用することができ、また不使用時には引き戸4Aを閉めて温風機3を完全に隠蔽し、外部から直接見えないようにすることができる。 - 特許庁
An adsorbent material 12 is arranged in the vicinity of the exhaust port of an exhaust passage 10 provided at a disposal tank 2 using microorganisms, and the exhaust amount of odor materials is more suppressed, so that the garbage disposal unit weak in odor is realized. 微生物による処理槽2に設けた排気通路10の排出口の近傍に吸着材12を配置し、より臭気物質の排出量を抑制し、臭気の低い生ごみ処理機を実現するものである。 - 特許庁
In this method, a specified shaping process is performed using a silver paste on a working mold of the almost same shape as a region to be decorated of the article to which the decorative object is fitted, and the silver paste is baked to obtain a silver decoration of an anticipated shape. 被装飾品の被装飾領域と略同一形状を有する加工型上に、銀ペーストを用いて所定の造形を行った後、焼成することにより、所期の形状を有する銀装飾を得る。 - 特許庁
The improvement of the positional precision of the lines is facilitated, the cost is reduced and the dispersion of quality is reduced by using plural number of fixing parts 9 in a state where the lines are in contact with each other in order to position the lines of the negative electrode jig for electrocasting. 電鋳の陰極治具の線の位置決めに線を接触した状態で固定部9を複数個使用することにより、線の位置精度を容易にし、安価にして、品質のバラツキを少なくできる。 - 特許庁
The glass plate 1 is fixed so that a surface 1b with a coating film formed thereon is inclined about 10° and coated with an infrared-cutting liquid 2, which is injected at the upper part of the glass plate 1, using a method for flowing the liquid vertically downward (flow coating). このガラス板1を被膜形成面1bが約10°となるように固定し、ガラス板1の上部に射出された赤外線カット液2を鉛直下向きに流す方法(フローコート法)にて塗布する。 - 特許庁
When the driving of the spiling pipes is completed, the end of each spiling pipe is locked and fixed to timbering 16n using a fixture, and upon the completion of locking and fixing, the front excavation of the working face 10n is performed. 縫地パイプ12の打設が終了すると、各縫地パイプ12の端部は、支保工16_nに止め金具を用いて係止固定され、係止固定が終了すると、切羽面10_nの前方掘削が行われる。 - 特許庁
Received owner control information is stored on the electronic device where the integrity of the received owner control information is verified and/or the source is authenticated using the owner identification information. 受信された所有者管理情報が電子装置に保存され、受信された所有者管理情報の完全性の検証および/または供給元の認証が、所有者識別情報を使用して行なわれる。 - 特許庁
The temperature control device 1 is equipped with a heat conductor 2 and a heat exchanging means 3, and is used in the state where the heat conductor 2 is sandwiched between the sample W and the heat exchanging means 3 by using a clamping means 5. 温度制御装置1は、伝熱体2および熱交換手段3を備えており、試料Wと熱交換手段3とで伝熱体2をクランプ手段5を用いて挟み込んだ状態で使用される。 - 特許庁
When the collision is avoided after the collision prediction, the high-voltage battery 2 is electrically connected to the inverter 4, and the traveling mode is changed to a regular traveling mode in which the vehicle travels by using the power of the high-voltage battery 2. そして、衝突予知後に衝突が回避された場合、高電圧バッテリ2とインバータ4を電気的に接続し、高電圧バッテリ2の電力を利用して走行する通常走行モードに走行モードを切り替える。 - 特許庁
To attach/detach a model by one operation in a model attaching/ detaching device for copy model attaching/detaching, which is used when a copy processing device is provided in a machine tool and an article to be machined is machined by using this device. 工作機械の内で倣い加工装置を持ちこれを使って被加工物を加工する際に使用する倣いのモデルを着脱するモデル着脱装置をワンタッチでモデルを着脱できるものを提供する - 特許庁
When the pulse signal before reaching the prescribed number is in the initial stage of the drive of the motor 10, wherein a frequency is unstable, a comparison is made by using a reference frequency computed based on the frequency in the stability of the frequency. 所定数前のパルス信号が、周波数が不安定なモータ10の駆動初期の場合は、周波数が安定したときの周波数に基づいて演算された基準周波数を用いて比較を行う。 - 特許庁
To provide an interdental brush with which interdental cleaning property is high and the gum is less damaged than in the case of using a conventional interdental brush, and where inside of a periodontal pocket is also cleaned sufficiently without being damaged. 歯間ブラシにおいて、歯間の清掃性が高く且つ従来の歯間ブラシよりも歯肉を痛める虞もなく、特に歯周ポケット内を傷めることなく十分に歯周ポケット内も清掃可能な歯間ブラシを提供する。 - 特許庁
To provide a working circumstance management system for an employee in which the salary of an employee is calculated under the consideration of a time when the employee is actually working using a personal computer, and the occurrence feeling of unfairness is prevented as a result. 従業員の給与を、実際にパソコンを使用して仕事をしている時間も考慮して算出して不公平感が生じないようにした従業員の勤務状況管理システムを提供する。 - 特許庁
In the case where the one-side printing is switched to the perfecting printing in the way of a print job using a used paper, the tray is automatically switched to a tray corresponding to the perfecting printing according to the tray selection designation or one-side printing is enforcedly carried out. 使用済用紙を使用している印刷ジョブで途中より両面に切り替わる場合、トレイ選択指示に従い、両面印刷できるトレイに自動的に切り替えるか、片面強制印刷する。 - 特許庁
For example, the siphon drain pipe 22A is connected to a connection part 51B, the siphon drain pipe 22B is connected to a connection part 51C, and the spare pipe 62 is connected to a connection part 51A without using the siphon drain pipe 22C. 例えば、サイフォン排水管22Aを接続部51Bへ接続し、サイフォン排水管22Bを接続部51Cへ接続し、スペア配管62を接続部51Aへ接続し、サイフォン排水管22Cを不使用管とする。 - 特許庁
The unevenness information of a finger of an individual person to be authenticated is compared with the unevenness information of a finger of the individual person which is previously registered, and individual person authentication is performed by using the threshold value peculiar to the individual person. そして、認証すべき個人の指のしわの凹凸情報を予め登録してあるその個人の指のしわの凹凸情報と比較し、かつ、設定したその個人特有の閾値を用いて個人認証を行う。 - 特許庁
To solve the following problems: since burrs at the inside part of a die-cast product have been removed by a manual work using a file, the physical fatigue of an worker is large, work efficiency is inferior, and uniform finish of the product is not obtained. ダイカスト製品の内面部分のばりを、やすりを使用し手作業で除去していた為、作業者の肉体的疲労が大きく、作業面から見ても効率が悪く、製品の仕上がりにも均一性が無い。 - 特許庁
To provide a flap door for a garage in which no braking force is applied when a door body is lifted by hands, which can be realized at low cost using a simple structure, and in which the door body can be lifted and opened by hands, even if there is no power failure. 扉体を手動で持ち上げるときには制動がからないようにでき、簡単な構造で安価に実現できると共に停電でない場合も手動で扉体を持ち上げて開放できるようにする。 - 特許庁
Thick resist 10 is applied in a thickness of about 200 μm on a wiring board 2 to serve as a base, and it is exposed to an ultraviolet ray using a photomask 11 where the section corresponding to the section to form the interlayer connecting electrode 6 is patterned. 下地となる配線基板2に厚膜レジスト10を200μm程度の膜厚で塗布し、層間接続電極6を形成する部分をパターニングしたフォトマスク11を用いて紫外線露光する。 - 特許庁
An adsorption belt 160 which is stretched to a driven roller 170 using a paper ejection roller 140 as a driving source and is moved cyclically clockwise in an arrow direction A is disposed between an aperture 10a and a fixing unit 130. 開口10aと定着器130との間には、排紙ローラ140を駆動源とする従動ローラ170に張架されて時計回りの矢印A方向に循環移動する吸着ベルト160が配備されている。 - 特許庁
The height of the lance 1 in the case of charging an auxiliary raw material 4, such as lime stone, is changed according to the number of using times of the lance 1 and a collapsing position with the auxiliary raw material 4 is changed, and also a worn position is changed to disperse the worn position. ランス1の使用回数によって石灰石等の副原料4を投入する際のランス1の高さを変え、副原料4との衝突箇所を変えて損耗箇所を変え、損耗箇所を分散させる。 - 特許庁
When an operator transmits a work start request command by using an ordering means which is not shown in a figure, this information is displayed in primary side yards (for example, batching plants) A_1 to A_6, and a predetermined work process is executed by the operator. 不図示の発注手段を使って作業者が作業開始要求コマンドを送信すると、1次側ヤード(例えば、バッチングプラント)A_1,…ではその情報が表示され、作業者は所定の作業工程を実施する。 - 特許庁
A threshold value: Z2 is set by using characteristics of an encoder of the data processing apparatus and a decoder of the falsification discrimination section and a setting region size or the like are used for parameters and the "presence of falsification" is discriminated when a relation of A/(A+C)≤Z2 is satisfied. データ処理装置側のエンコーダと改竄判定部のデコーダの特性及び設定領域サイズ等をパラメータとして閾値:Z2を設定し、A/(A+C)≦Z2が成立すれば「改竄あり」と判定する。 - 特許庁
In a traction type machine-roomless elevator formed that a rope, a cage, and a balancing weight are hung down and driving is effected by using the hoisting machine, the machine-roomless elevator featured that the hoisting machine is mounted on the frame of a balancing weight is provided. ロープでかごとつり合い重りを吊り下げ、巻上機を用いて駆動するトラクション式マシンルームレスエレベータにおいて、巻上機をつり合い重りのフレームに取付けたことを特徴とするマシンルームレスエレベータ。 - 特許庁
To obtain a liquid crystal display in which the absorption axis of a polarizing plate is matched with the optical axis of a retardation plate highly precisely without using an expensive apparatus and a complicated process, and which has a wide viewing angle , is low in power consumption and is high in definition. 高価な装置や煩雑な工程を用いずに偏光板の吸収軸と位相差板の光学軸を高精度に一致させ、広視野角で低消費電力、高品位な液晶表示装置を得る。 - 特許庁
To provide a connecting method of titanium thin sheets by which there is no possibility of occurrence of break even when stress with deformation such as bending and twisting is imparted to the connected part and a connected member which is connected by using the same. 接続部に曲げやねじれなどの変形に伴う応力が付与されても、破断が生じるおそれのないチタン薄板の接続方法及びそれを用いて接続した接続部材を提供するものである。 - 特許庁
The printed matter is temporarily fixed along an inner wall of a drying chamber as a main body, a rotary fan using an impeller is mounted on a central part inside the drying chamber, and the fan is rotated to bring air to the printed matter. 本体となる乾燥室の内壁に沿って印刷物を仮留めし、乾燥室の内側中心部に羽根車を用いた回転ファンを設け、ファンを回転させることで印刷物に風が当たるようにする。 - 特許庁
Using the upper surface and the side face at the upper stage of level difference as nuclei, GaN 32 is grown epitaxially in the lateral direction and the upper part of the lower stage of level difference (recess of the original substrate 1) is filled before GaN 32 is also grown epitaxially above. こうして、段差の上段の上面及び側面を核として、GaN32を横方向エピタキシャル成長させることで段差の下段(元基板1の凹部)上方を埋めたのち、さらに上方にも成長させる。 - 特許庁
When the outer ring is cleaned, the inner peripheral surface of the outer ring containing the ball rolling contact surface and the grooved surface is cleaned by using the high-pressure liquid jet stream to be jetted from the nozzle 8a of the pipe 8 in the same manner as the ring 2 is cleaned. 同様に、高圧液体ジェット噴射管の噴射口から噴射される高圧液体ジェットを使用して、ボールベアリングの外輪のボール転動面とグルーブ面とを含む内周面を洗浄する。 - 特許庁
An U section aluminum piece 2 in L-form is attached to the body 1 of a transparent clip, the piece 2 is provided with a hole for sliding and a projecting slide 3, and is also equipped in its upper part with a long clip 4 using a thumbscrew. 透明クリップ本体(1)にL型∩字アルミ(2)を取付け、L型∩字アルミ(2)にスライド用の穴をあけ、凸型スライド(3)を設け、スライド(3)の上部に蝶ネジで長いクリップ(4)を設けたことを特徴とする。 - 特許庁
If the brightness of the document is higher than a set value, that is, the brightness of the document is close to white (step S14: NO), the document size detection part detects the size of the document using the image read in step S12 (step S17). 原稿の明度が設定値より大きい場合、つまり原稿の明度が白に近い場合(ステップS14;NO)、原稿サイズ検出部はステップS12で読み取った画像用いて原稿サイズを検出する(ステップS17)。 - 特許庁
To provide a bamboo spectacle frame which is formed by using materials to take place of the materials of the conventional metallic frames and resin spectacle frames, is extremely lighter than as it looks, is strong to the sweat and enables even an allergic person to wear the spectacle frame without anxiety. 従来の金属製メガネフレーム及び樹脂製メガネフレームに代わる材質を用い、見掛けに比べて非常に軽く、汗には強く、またアレルギー性の人も安心して着用出来る竹製メガネフレームの提供。 - 特許庁
A pocket 1 easy to put in and to put out the penis is prepared by using urine absorbing paper [figure 2], a comparatively large adhesive tape 3 is stuck on the back side face [figure 4] and the penis is settled down so that the leak of urine from the side can be prevented. 尿吸収紙を使用して陰茎の出し入れし安い〔図2〕1を作りその裏側面に大き目の接着テープを貼り付け〔図4〕3陰茎を落ち着かせて尿の横漏れを防止する様にした - 特許庁
To provide a nickel powder wherein the content of impurities is low using a method for producing a nickel powder where nickel hydroxide obtained by a wet process is reduced, and to provide a method for producing the same so that the organic matter in a waste liquid is easily recovered. 湿式法で得た水酸化ニッケルを還元するニッケル粉の製造方法を用いて、不純物含有量が低いニッケル粉と廃液中の有機物の回収が容易なその製造方法を提供する。 - 特許庁