(1) The filling liquid for a liquid ejector which is filled in a liquid ejection head includes an alkaline electrolytic ion water, wherein the total amount of alkali metal (Li, Na, K) concentration and alkaline earth metal (Mg, Ca, Sr, Ba) concentration in the filling liquid is 1,000 ppm or less, and pH is 10 or more. (1)液体吐出ヘッドに充填される充填液であって、アルカリ電解イオン水を含有し、充填液中のアルカリ金属(Li、Na、K)濃度、及びアルカリ土類金属(Mg、Ca、Sr、Ba)濃度の合計が1000ppm以下で、pHが10以上であることを特徴とする液体吐出装置用充填液。 - 特許庁
A porosity is raised by restraining condensation of the eosine Y in the zinc oxide film while a density of the eosine y in the zinc oxide film is adjusted at 100 μM or more and 130 μM or less, and the zinc oxide porous layer having a larger surface area is formed, in order to constitute the dye-sensitized solar cell having higher photoelectric conversion efficiency. 浴液中のエオシンYの濃度を100μM以上、130μM以下に調整することで、酸化亜鉛被膜中のエオシンYの凝集を抑制させて空隙率を高め、より表面積の大きな酸化亜鉛多孔質層を形成させて、高い光電変換効率を持つ色素増感太陽電池を構成させる。 - 特許庁
Further, when the mercury gas density detected by the third mercury gas densitometer 26 is 0.5 mg/m^3 or less and the gas flow rate detected by the flow meter 30 is 2.8 m^3/min or more after starting up the suction and exhaust fan 10, charging of a broken fluorescent tube into a broken fluorescent tube storage container 4 is allowed. また、吸排気ファン10の起動後、第3の水銀ガス濃度計26で検出した水銀ガス濃度が0.5mg/m^3以下で、流量計30で検出したガス流量が2.8m^3/min以上の場合に、破損蛍光管収容容器4への破損蛍光管の投入を許容するようにした。 - 特許庁
The wheel molded of a material by casting a wheel diameter of which ismore than 16 inches and the deflection of the bead seat part of which isless than 0.2 mm is manufactured by machining an offset surface of the wheel material, fixing the offset surface of this wheel material on the machining device as a machining standard part and lathe-machining an outer peripheral surface of its rear rim part. ホイール素材のオフセット面を加工し、このホイール素材のオフセット面を加工基準部として加工装置に固定し、その後リム部の外周面を旋盤加工することで、ホイール径が16インチ以上であり、ビードシート部のフレが0.2mm以下である鋳造により素材成形されたホイールを製造する。 - 特許庁
When digital data is copied from a copy source hard disk driving device 6M (hereinafter referred to as "copy source HD" ) to a copy destination hard disk driving device 6T1 ("copy destination HD"), an area where a read error isless likely to occur is set as a read start position, and more data are read before an error occurs during reading. コピー元ハードディスクドライブ装置6M(以下「コピー元HD」)からコピー先ハードディスクドライブ装置6T1(以下「コピー先HD」)へデジタルデータをコピーする際に、読み取りエラーが発生する可能性の低い領域を読取開始位置として設定し、読み取り時にエラーが発生する前に、より多くのデータを読み取る。 - 特許庁
One example of this gas detection method is provided with a process for making a sample gas flow out of the oven, a process for determining whether a flow rate thereof is the minimum value or less or not, and a process for determining whether a concentration of the first gas such as the inflammable gas in the sample gas is the maximum value or more or not. ガス検出方法の一例は上記オーブンから試料ガスを流出させる工程と、その流量が最小値以下であるかどうかを判定する工程と、上記試料ガス中の、可燃性ガスなどの第1のガスの濃度が最大値以上であるかどうかを判定する工程とを備えている。 - 特許庁
In an LED with a light emitting layer of quantum well texture consisting of AlGaN, a difference in an AL composition between a barrier layer forming the quantum well texture and the quantum well texture layer is within 15%, and the AL composition of the quantum well texture layer is 2% or more, and the thickness of the quantum well texture layer is 4 nm or less. AlGaNからなる量子井戸構造の発光層を有するLEDにおいて、前記量子井戸構造を構成する障壁層と量子井戸層のAl組成の差が15%以内であり、かつ前記量子井戸層のAl組成が2%以上であり、かつ、前記量子井戸層の厚さが4nm以下である。 - 特許庁
The light diffusion film contains light diffusion elements or air bubbles in the film, wherein the minimum variable angle θ_60min at incident angle 60° is 12° or more, the maximum variable angle θ_60max at incident angle 60° is 108° or less and the total thickness of the film is 10 μm to 1,000 μm. 本発明の光拡散フィルムは、フィルム内部に光拡散素子あるいは気泡を含有するフィルムであって、入射角度60°での最小変角度(θ_60min)が12°以上及び最大変角度(θ_60max)が108°以下、並びに、フィルムの総厚みが10μm〜1000μmであることを特徴とするものである。 - 特許庁
A ratio of (a) the diphenyl carbonate occupied in the nonaqueous electrolyte solution is 0.001 wt.% or more and less than 5 wt.%, a ratio of (b) the total compound is 0.001 to 20 wt.%, and a ratio of the ethylene carbonate to a sum of the ethylene carbonate and dialkyl carbonate in the nonaqueous solution is 5 to 50 vol.%. 非水系電解液に占める(a)ジフェニルカーボネートの割合が0.001重量%以上5重量%未満であり、化合物(b)の合計の割合が0.001〜20重量%で、非水溶媒中のエチレンカーボネートとジアルキルカーボネートとの合計に対するエチレンカーボネートの割合が5〜50容量%である。 - 特許庁
When the predetermined quantity or more of particles is heaped on the particulate filter carrying the catalyst and temperature of the exhaust gas is the predetermined temperature or less, the compressed air is led into the particle filter from a downstream side of the exhaust in the particulate filter to eliminate the particles heaped on the particulate filter, and the eliminated particles are burned up. 触媒を担持したパティキュレートフィルタにパティキュレートが所定量以上堆積し、しかも排気ガス温度が所定温度以下の場合にはパティキュレートフィルタの排気下流側から圧縮空気をパティキュレートフィルタ内に導入してパティキュレートフィルタに堆積したパティキュレートを除去し、この除去されたパティキュレートを焼却する。 - 特許庁
The free magnetic layer 14 is constituted so that the strength of function for combining a ferromagnetic layer 15_j (j is an arbitrary integer of 2 or more and N-2 or less) and a ferromagnetic layer 15_j+1 is antiferromagnetically stronger than the strength of function for combining the first ferromagnetic layer 15_1 and a second ferromagnetic layer 15_2 antiferromagnetically. 自由磁性層14は,強磁性層15_j(jは2以上N−2以下の任意の整数)と強磁性層15_j+1とを反強磁性的に結合させる作用の強さが,第1強磁性層15_1と第2強磁性層15_2とを反強磁性的に結合させる作用の強さよりも強いように構成されている。 - 特許庁
This replacement material for washing the piping part prepared by mixing and kneading a powdered material compound, of which the granularity is adjusted, with the water, does not include a binder which is hardened or solidified at a temperature zone of 100°C or less, and has a tap flow value of 140 mm or more after being left as it is for 24 hours after the kneading. 粒度調整された粉体状の原料配合物と水とを混練してなる配管部洗浄用置換材であって、100℃以下の温度域で硬化及び凝集するような結合剤を含有せず、かつ混練後24時間放置した後のタップフロー値が140mm以上である配管部洗浄用置換材。 - 特許庁
The game condition is limited to either one of a first RT with small token dispensing rate less than one and a second RT wherein replay winning probability is remarkably high compared to ordinary game condition and token dispensing rate ismore than one from initial game condition controlled after changing set value or after the completion of regular bonus or big bonus. 設定値の変更後やレギュラーボーナスまたはビッグボーナスの終了後などに制御される初期遊技状態からは、メダルの払出率が1よりも小さい第1RTと、リプレイ当選確率が通常の遊技状態に比べて極めて高く、メダルの払出率が1を超える第2RTのいずれかに遊技状態が制御される。 - 特許庁
A crystallite size and nonuniform strain of a target material are measured by an X-ray diffraction and, under at least one of conditions that the crystallite size is 30 nm or less and the nonuniform strain is 0.25% or more, a prediction of the formation of rolling fatigue crack of the target material is determined. 対象材に対してX線回折により結晶子サイズおよび不均一ひずみを測定し、結晶子サイズが30nm以下であるとの条件及び不均一ひずみが0.25%以上であるとの条件の少なくとも一方の条件で対象材に対して転がり疲労き裂の発生予測を決定する。 - 特許庁
In the plurality of toner images, the average adjacency rate of all the pixels on which the beam B is radiated is not less than 0 and not more than 0.59, an adjacency rate being obtained by dividing the sum of the values obtained by multiplying the data values of pixels around a pixel on which the beam B is radiated by factors of a table, by the sum of the factors of the table. 複数のトナー画像では、ビームBが照射される画素の周囲の画素のデータ値にテーブルの各要素をかけて得られる値の和を該テーブルの各要素の和で割って得られる隣接率を、ビームBが照射される全ての画素について平均した平均隣接率が、0以上0.59以下である。 - 特許庁
The method of manufacturing inorganic particles by: heat-treating a starting material containing paper sludge to obtain a calcined product; and dispersing the calcined product with a high-shear dispersion machine having a circumferential speed of 10 m/s or more, polycarboxylate is used as a dispersant and a TI value of dispersed slurry which is adjusted is 10 or less. 製紙スラッジを含む原料を熱処理して得た焼成物を攪拌周速10m/s以上の高せん断分散機により分散して無機粒子を製造する方法であって、 分散剤としてポリカルボン酸塩を用い、調整した分散スラリーのTI値が10以下であることを特徴とする無機粒子の製造方法。 - 特許庁
The working vehicle is provided with a control device which causes an engine speed change instruction means and a shift instruction means to perform shift instruction when the instructed engine speed is equal to or more than the prescribed engine speed and instructs the prescribed engine speed to the engine speed change instruction means when the engine speed isless than the prescribed engine speed. そして、指示エンジン回転数が所定回転数以上のときには、エンジン回転数変更指示手段と変速指示手段による変速指示を行い、エンジン回転数が所定回転数未満のときにはエンジン回転数変更指示手段に所定回転数を指示する制御装置を設けた作業車両である。 - 特許庁
A communication passage 41 is provided for disconnecting the independent branch passages from each other when the opening of the variable throttle valve isless than a predetermined opening while mutually connecting the independent branch pipes between cylinders with valve opening periods of exhaust valves overlapped with each other when the opening of the variable throttle valve 30 is the predetermined opening or more. 可変絞り弁30が該所定開度以上のときに排気弁の開弁期間が互いにオーバラップする気筒間での該各独立分岐通路同士を連通をさせる一方、該可変絞り弁が所定開度未満のときに各独立分岐通路同士の連通が遮断される連通路41が設けられる。 - 特許庁
A breaker switch 13 and a superconductive part 14 are connected in series and immersed in liquid nitrogen of an ultra-low temperature thermostatic tank 11 in which liquid nitrogen is filled, and the superconductive part 14 maintains a superconductive state when the current isless than a critical value and limits current when it is the critical current value or more. 液体窒素が充填された極低温恒温槽11の液体窒素中に遮断スイッチ13と超電導部14とを直列に接続して浸漬し、超電導部14は、電流が臨界電流値未満のときは超電導状態を保ち臨界電流値以上のときは電流を限流する。 - 特許庁
In the region in which at least one optical element in the aligner is installed, the exposure method is conducted in such way that the gas partial pressure of methan, ethan, propane, butane, iso butane, neopentane, cyclopropane, cyclobutane, pentane, octane or these admixtures is controlled to be 1.5E-8Pa or more, 1.0E-2Pa or less. 露光装置内の少なくともひとつの光学素子が設置されている領域において、メタン、エタン、プロパン、ブタン、イソブタン、ネオペンタン、シクロプロパン、シクロブタン、ペンタン、オクタンもしくはこれらの混合物のガス分圧を1.5E−8Pa以上1.0E−2Pa以下に制御することを特徴とする露光方法、露光装置、及びパターン形成方法。 - 特許庁
Then it is desirable that a space between the power supply wirings 13, 14 is 0.8 μm or less; the wirings 13, 14 have patterns bent at a length L of several hundreds μm; and a space between the wiring 13 and the wiring 14 at a part thereof bent (a deflation point 20) is 0.8 μm or more. 電源配線13と電源配線14の間隔が0.8μm以下であり、電源配線13,14が数百μmの長さLで屈曲させたパターンを有し、この屈曲させた部分(空気抜きポイント20)の電源配線13と電源配線14の間隔が0.8μmより大きいものであることが好ましい。 - 特許庁
The electrophotographic coating sheet is made by imparting a rugged pattern to one surface of the coating sheet prepared by forming at least one of coating layer on both surfaces of a base paper, wherein the electrophotographic coating sheet has the rugged surface in which the solid content coating amount on the rugged surface is 5 g/m^2 or more and the BEKK smoothness is 200 sec or less. 原紙の両面に1層以上の塗工層を設けた塗工シートの片面に凹凸模様を付与した電子写真用塗工シートにおいて、該凹凸面の固形分塗工量が5g/m^2以上で、BEKK平滑度が200秒以下である事を特徴とする凹凸面を付与した電子写真用塗工シート。 - 特許庁
As a conductive assistant for a positive electrode pole plate, expanded graphite having the DBP absorption quantity of 200 ml/100 g or more and 500 ml/100 g or lessis used, thereby, the active material, the conductive assistant, and the binder are uniformly dispersed, thus adhesion is improved and uniform reaction is carried out. 正極用極板の導電剤として、DBP吸収量が200ml/100g以上、500ml/100g以下の膨張化黒鉛を用いることによって、活物質、導電剤および結着剤を均一分散させることができるので、集電体との密着性に優れ、均一反応が進行する。 - 特許庁
This is a grinding particle slurry for polishing constituted of grinding particles A having weight mean particle diameter [D] which is 0.1-50 μm in which the number of grinding particles having particle diameter 2D or more to be measured by a filtering method using a sieve having sieve mesh openings having 2D is set so as to be 2 or less per 1 g and dispersant B and water. 0.1〜50μmの重量平均粒径[D]を有し、2Dのフルイ目開きを有するフルイを用いてろ過する方法により測定される2D以上の粒径を持つ砥粒粒子の数が、1gあたり2個以下である砥粒(A)と分散剤(B)および水からなることを特徴とする研磨用砥粒スラリー。 - 特許庁
In the glare shielding optical film having a minute surface uneven structure on at least a one-sided face of a transparent film base material, a rate in which an inclined angle is 10 degrees or moreis 2% or less, and an average interval between projections of the minute surface unevenness is 1 μm or 50 μm. 透明フィルム基材の少なくとも片面に表面微細凹凸構造を有する防眩性光学フィルムにおいて、傾斜角度が10°以上である割合が、2%以下であり、かつ表面微細凹凸の山の平均間隔が1μm乃至50μmであることを特徴とする防眩性光学フィルム。 - 特許庁
Receiver side equipment sends an opening notification to the transmitter in the case that the text display time of reception mail is fixed time or more or display is performed to the final character string of the text of the mail and notifies a preset message to a transmitter side in the case that the text display time of the mail isless than the fixed time. 受信者側装置は、受信メールの本文表示時間が一定時間以上であれば、または、メールの本文の最終文字列まで表示された場合、送信者へ開封通知を送付し、また、該当メールの本文表示時間が一定時間以下である場合、予め設定しておいたメッセージを送信者側に通知する。 - 特許庁
Therefore, a diamond thin film is obtained which film has a modified film thickness range in which a half value width of a diamond spectrum evaluated by a Raman spectroscopy of 0.1 μm or more along the direction of a film thickness of the diamond thin film is approximately constant, and the half value width is 85% or less of the maximum half value width of a film thickness remainder. ダイヤモンド薄膜の膜厚方向に沿って、0.1μm以上のラマン分光法で評価したダイヤモンドスペクトルの半価幅がほぼ一定である改質された膜厚み領域を有し、その半価幅は膜厚み残部の同最大半価幅の85%以下であるダイヤモンド薄膜が得られる。 - 特許庁
A protective member 5 which is elastically deformed by a load less than a predetermined value received from the compressor 4 when the compressor 4 is moved freely, and plastically deformed by a load of the predetermined value or more received from the compressor 4 is provided within a body casing 10 of the outdoor unit X located within the freely moving range of the compressor 4. 圧縮機4が遊動されたときに該圧縮機4から受ける所定未満の荷重により弾性変形し,該圧縮機4から受ける所定以上の荷重により塑性変形する保護部材5が,前記圧縮機4の遊動範囲内に位置する室外機Xの本体筐体10に設けられている。 - 特許庁
This single crystal pulling-up method is characterized in that the time required for passing the temperature region of 1,150-1,050°C is regulated to more than 50 min and/or that of 1,050-950°C is regulated to less than 40 min in a process for pulling up the single crystal while growing from a nitrogen- doped silicon raw material melted liquid. (1) 窒素がドープされたシリコン原料融液から単結晶を成長させながら引上げる方法であって、前記単結晶の引上げ過程で1150〜1050℃の温度領域の通過時間を50分以上、または/および1050〜 950℃の温度領域の通過時間を40分以下とすることを特徴とする単結晶の引上げ方法である。 - 特許庁
The sealing film for solar cell contains ethylene-vinyl acetate copolymer and organic peroxide, wherein a maximum torque M_H is 0.20 N×m or more and a minimum torque M_L is 0.05 N×m or less, at 150°C when it is measured by oscillation method vulcanizing test conforming to JIS K 6300-2. エチレン酢酸ビニル共重合体及び有機過酸化物を含む太陽電池用封止膜であって、 JIS K 6300−2に準じた振動式加硫試験により測定した150℃における最大トルクM_Hが0.20N・m以上であり、最小トルクM_Lが0.05N・m以下であることを特徴とする太陽電池用封止膜。 - 特許庁
A latch type sense amplifier circuit is provided with a first latch circuit 3 and a second latch circuit 4 which output signals being equal each other when potential difference between a pair of bit lines is the prescribed value or more, and output signals being different each other when the potential difference between a pair of the bit lines isless than the prescribed value. ラッチ型センスアンプ回路には、ビット線対間の電位差が所定値以上であるときに相互に等しい出力信号を出力し前記ビット線対間の電位差が所定値未満であるときに相互に異なる出力信号を出力する第1のラッチ回路3及び第2のラッチ回路4が設けられている。 - 特許庁
The photonic liquid crystal is a transparent and amorphous metal oxide thin film including fine pores inside, and the refractive index (a refractive index to the light of λ = 500 nm) is ≥1.8, and the diameter of the fine pores occupying 80 vol% or more of the whole fine pores is 5 nm or less. 透明でかつ、内部に微細な空隙を含む非晶質金属酸化物薄膜であって、屈折率(λ=500nmの光の屈折率)が1.8以上であり、微細空隙全体の80体積%以上を占める微細空隙の直径が5nm以下である非晶質金属酸化物薄膜からなるフォトニック液晶。 - 特許庁
The printing plate material comprises a support provided with a hydrophilic layer and an imaging layer laminated on it in this order is characterized in that the hydrophilic layer is a fine-grained porous layer and that the peak pore size in pore size distribution curve on this fine-grained porous layer is 0.005 μm or more, 1.000 μm or less. 支持体上に、親水性層、画像形成層をこの順に積層した印刷版材料において、親水性層が微粒子多孔質層であり、該微粒子多孔質層の孔の孔径分布曲線におけるピーク孔径が0.005μm以上1μm以下であることを特徴とする印刷版材料。 - 特許庁
The optical information recording method for recording information in an optical recording medium having a recording layer on a substrate at a linear speed of 15m/s or moreis characterized in that surface wobbling acceleration is 2m/s^2 or less when the optical information recording medium is measured at a linear speed of 3.5m/s. 基板上に記録層を有する光情報記録媒体に、線速度が15m/s以上で情報を記録する光情報記録方法であって、前記光情報記録媒体を線速度3.5m/sで測定したときの面振れ加速度が2m/s^2以下であることを特徴とする光情報記録方法である。 - 特許庁
As in the above example, the electrolytic solution is used containing 5 to 30 wt.% of the solvent, whose solubility to sulfur is not less than 20 mM, 20 to 70 wt.% of a solvent whose solubility to sulfur is not more than 20 mM and 20 to 70 wt.% of a solvent, which has a high dielectric constant and a high viscosity, and containing an electrolytic salt. 上記例のように、硫黄に対する溶解度が20mM以上の溶媒を5〜30重量%、硫黄に対する溶解度が20mM以下の溶媒を20〜70重量%、誘電定数が大きく粘度が高い溶媒を20〜70重量%と電解塩を含む電解液を用いる。 - 特許庁
The resin-coated metal plate having high coating peeling resistance during roll forming and provided with a resin coating obtained from a surface treated composition is characterized in that Sward rocker hardness of the resin coating is 35 or more and an indentation depth of an indenter in nano-scratch test isless than 0.3 μm. 表面処理組成物から得られた樹脂皮膜を備える樹脂塗装金属板であって、この樹脂皮膜のスォードロッカー硬度が35以上であり、かつ、ナノスクラッチ試験における圧子の進入深さが0.3μm未満であることを特徴とするロール成形時の耐皮膜剥離性に優れた樹脂塗装金属板である。 - 特許庁
An oil phase component obtained by dissolving or dispersing a binder resin and a colorant in an organic solvent, is dispersed and granulated in an aqueous medium with a dispersed inorganic dispersant to obtain a developer, in which the binder resin is a polyester resin of which acid value is 0.3 mgKOH/g or more and 1.4 mgKOH/g or less. 結着樹脂および着色剤を有機溶媒中に溶解または分散させて得た油相成分を、無機分散剤を分散させた水性媒体中に分散造粒させて得られる現像剤において、前記結着樹脂を、酸価が0.3mgKOH/g以上かつ1.4mgKOH/g以下のポリエステル樹脂とした。 - 特許庁
With a head driven by a driving frequency of 15 kHz or higher, a recording is performed by discharging an ink, which includes carbon black, the volatile component of which is 15 mass % or less and the nitrogen adsorption specific surface area of which is 100 m2/g or more, a dispersant and a solvent in this ink jet recording method. 駆動周波数15kHz以上で駆動するヘッドにて、揮発成分が15質量%以下であり、且つ窒素吸着比表面積が100m^3/g以上のカーボンブラック、分散剤及び溶媒を含有するインクを吐出することにより記録を行うことを特徴とするインクジェット記録方法。 - 特許庁
The biaxially stretched resin film is characterized in that: it is composed of a layer containing a polyethylene terephthalate resin (A) and a layer containing a syndiotactic polystyrene resin (B), which are laminated alternately in total of five or more layers; and absolute value of retardation measured by polarization microscope with Berec compensator is 500 nm or less. ポリエチレンテレフタレート系樹脂(A)を含む層とシンジオタクチックポリスチレン系樹脂(B)を含む層が交互に合わせて5層以上積層されており、ベレック型コンペンセーターを用いた偏光顕微鏡により測定されるレターデーションの絶対値が500nm以下であることを特徴とする二軸延伸樹脂フィルム。 - 特許庁
A conductive spacer 9 is provided in the gap 10 and an inert gas is sealed in the gap 10 under water pressure or more so that contraction of the metallic sheath 2 caused by outer water pressure is restricted and repeated strains of the metallic sheath 2 are reduced to a predetermined value or less. 絶縁コア1と金属シース2間に空隙部10を設け、前記空隙部10に導電性スペ−サ−9を備え、且つ不活性気体を水圧以上に加圧封入して外水圧による金属シース2の収縮を押さえることにより金属シース2の繰返し歪みを所定値以下としたものである。 - 特許庁
In the container the inner wall face of which is a polymer composition of polypropylene which is manufactured with a metallocene type catalyst and has a melting point of 140°C or less, and an olefin or styrene type thermoplastic elastomer, a part of the opposite inner wall face is partitioned into two or more storing chambers by a peelable heat seal. メタロセン系触媒で製造され、かつ融点が140℃以下であるポリプロピレンと、オレフィン系またはスチレン系熱可塑性エラストマーとの重合体組成物を内壁面とする容器であって、相対する内壁面の一部が剥離可能な熱シールによって複数の収容室に区画されている。 - 特許庁
An ink-jet recording paper is provided with a glossy layer formed on the side of a recording face of a paper base and a polyolefin resin- containing layer on its reverse side, and the 75° glossiness (JIS-P8142) on the surface of the glossy layer is 30% or more, and the 75° glossiness of the surface of the polyolefin resin containing layer is 50% or less. 紙基材の記録面側に光沢層を設け、裏面にポリオレフィン樹脂含有層を設けたインクジェット記録用紙において、光沢層表面の75°光沢度(JIS−P8142)が30%以上であり、ポリオレフィン樹脂含有層表面の75°光沢度が50%以下であることを特徴とするインクジェット記録用紙。 - 特許庁
It is judged whether or not the residual quantity S of ink equals to the amount T of usage which is necessary for printing or more (step S30) only when the residual quantity S of ink in each ink cartridge reaches the amount R of monitoring judgement or less which is defined by at least one condition selected from the type of media and printing modes (YES in step S15). 各インクカートリッジのインクの残量Sが、メディアの種類及び印字モードのうち少なくとも1つ以上の条件により定められた監視判断量R以下となった場合(ステップS15にてYES)にのみ、インクの残量Sが印刷に必要な使用量T以上あるか否かを判断する(ステップS30)。 - 特許庁
At the start of a polymerization step, an alcohol having 4 or less carbon atoms and a 85°C or more boiling point is added into an aqueous medium, and a polymerizable monomer emulsified-stabilized in the aqueous medium, which is a causative substance to polymer deposition, is demulsified and thereby preventing the polymer from being deposited. 重合工程の開始時に該水系媒体中に炭素数4以下かつ沸点が85℃以上であるアルコールを添加し、重合体付着物の起因物質である水系媒体中で乳化安定化した重合性単量体を解乳化させることにより、重合体付着物の生成を抑制する。 - 特許庁
The plurality of operation modes include a normal mode showing that the power supply voltage is not less than a first threshold voltage and a data storage mode showing that the power supply voltage is ranging from the first threshold voltage to the second threshold voltage and a data erasure mode showing that the power supply voltage is not more than the second threshold voltage. 複数の動作モードは、電源電圧が第1閾値電圧以上の電圧であることを示す通常モードと、電源電圧が第1閾値電圧から第2閾値電圧の範囲であることを示すデータ保持モードと、電源電圧が前記第2閾値電圧以下であることを示すデータ消去モードとを含む。 - 特許庁
(i) Even with the best attacking technique available to date, computational cost to find the input value for a specific output value is not less than computational cost required for the exhaustive search. Also, even if the best attacking technique is used, computational cost to find a pair of input values with the same output value is 2128 or more.
(イ)特定の出力に対する入力値を発見する手間への耐性が十分に高く(最良の解読技術を適用しても 2160 以上の計算量)、かつ出力値が一致するような異なる入力値を発見する計算量が最良の解読技術を適用しても 280 以上であること。 - 経済産業省
In the macroporous type ion exchange resin, the pore volume when measured by the mercury porosimetry is 0.5 mL/g per dry weight of 1 g of the ion exchange resin or more, the pore radius when measured by the mercury porosimetry is 0.1 μm or more and the turbidity component eluted by the shaking turbidity test of the ion exchange resin is 45 ppm or less. マクロポーラス型のイオン交換樹脂であって、水銀圧入法で測定したときの細孔容積が、前記イオン交換樹脂の乾燥重量1gあたり0.5mL/g以上であり、水銀圧入法で測定したときの細孔半径が、0.1μm以上であり、かつ、イオン交換樹脂の振とう濁度試験で溶出する濁度成分が、45ppm以下である、ことを特徴とする、イオン交換樹脂。 - 特許庁
This vibrating actuator having a diaphragm mounted on a power transmitting part is provided with at least three diaphragm reinforcing ribs constituted of high rigid materials whose thickness is 60 micron meters or more and 5 mm or less, and whose vertical elastic coefficient is 68 GPa or more, and extended to a vibration transmitting direction formed against the diaphragm without any division line or node in its configuration crossing the vibration transmitting direction. 動力伝達部に取り付けられた振動板を有する振動アクチュエータにおいて、厚さ60ミクロンメートル以上5ミリメートル以下で縦弾性係数が68GPa以上の、高剛性の材料からなり、振動伝搬方向を横切る形では分割ラインおよび節のない振動板に対して、振動伝搬方向に延びる振動板補強リブを3個以上設けたことを特徴とする振動アクチュエータ。 - 特許庁
The photocurable resin composition comprises (a) 20-60 wt.% of one or more monomers having three or more acrylic groups and/or methacrylic groups in one molecule, in which (b) ingredients which bind through photocurable reaction to form a solid are in an amount of 98 wt.% or more, and (c) the viscosity is 10 mPa s or less at 25°C. (a)1分子中に3以上のアクリル基及び/またはメタクリル基を含有する1種以上の単量体を、20〜60重量%の範囲で含有することを特徴とする光硬化性樹脂組成物であって、(b)光硬化反応によって結合して固形となる成分が98重量%以上であり、(c)25℃における粘度が10mPa・s以下であることを特徴とする、光硬化性樹脂組成物。 - 特許庁
The inkjet ink composition includes a water soluble dye, water, a water-soluble diol compound in a content of 25 mass% or more, and a water-soluble monoalcohol compound in a content of 5 mass% or more, wherein the content of the water-soluble diol compound to the total amount of the water-soluble diol compound and the water-soluble monoalcohol compound is 60 mass% or more and 81 mass% or less. インクジェット用インク組成物を、水溶性染料と、水と、含有率25質量%以上の水溶性ジオール化合物と、含有率5質量%以上の水溶性モノアルコール化合物とを含み、前記水溶性ジオール化合物および水溶性モノアルコール化合物の総量に対する前記水溶性ジオール化合物の含有率が60質量%以上81質量%以下であるインクジェット用インク組成物。 - 特許庁