「Modulus」を含む例文一覧(4949)

<前へ 1 2 .... 78 79 80 81 82 83 84 85 86 .... 98 99 次へ>
  • To provide a cushion body the modulus of elasticity of which is not too high, which is light, in which the flow of the contents gives no discomfort, which gives no cold feel and also gives no hard feel because not only a pressed part but also the whole has a uniformly high pressure when pressed by the human body, or the like.
    弾性率が高くなり過ぎることがなく、軽量で、内容物の流動が不快感を与えず、冷たく感じることがなく、人体等に押圧された際、その押圧された部分のみならず、全体に均一に圧力が高くなり、硬さを感じることもないクッション体を提供する。 - 特許庁
  • If a holding member of the semiconductor laser is formed with the material equal to or more than 10×1010 (N/m2) of the Young' s modulus, distortion in the light source device is hard to be produced, variation in the interval of the subscanning direction of the light spot on the surface to be scanned can be suppressed, and a sure and stable image reproducibility can be assured.
    ヤング率が10×10^10(N/m^2)以上の材料で半導体レーザの保持部材を形成すれば、光源装置に歪みを生じ難く、被走査面上の光スポットの副走査方向間隔の変動を抑えることができ、確実で安定な画像再現性が確保できる。 - 特許庁
  • The resin film is 0.2-10 μm-thick and is formed from a resin composition having an acid value of 40-90, a urethane group content (in terms of NCO group content) of 12-20 wt.%, an elastic modulus at 100°C of 1,000-60,000 N/cm2, and a flow start temperature of 75-170°C.
    樹脂皮膜を酸価が40〜90、ウレタン結合含有量がイソシアネ−ト基(NCO)換算で12〜20重量%、100℃における弾性率が1000〜60000N/cm^2および流動開始温度が75〜170℃である樹脂組成物にして、皮膜厚を0.2〜10μmにした。 - 特許庁
  • As for the cover glass used for the total reflection illuminating fluorescence microscope, a substantially transparent thin film whose Young's modulus is 0.5 to 2KPa and whose refractive index is 1.4 to 1.5 exists on one surface of a glass substrate, and the thin film is formed such that many particulates are dispersed and fixed on its surface which is not in contact with the glass substrate.
    ガラス基板の片面上にヤング率0.5〜2KPaで、屈折率1.4〜1.5の実質的に透明な薄膜が存在し、該薄膜はガラス基板と接していない表面に多数の微粒子が分散固定された全反射照明蛍光顕微鏡に用いるカバーガラスである。 - 特許庁
  • This stretched thermoplastic polyester-based resin sheet is characterized by having a tensile elastic modulus of ≥9.0 GPa, a linear expansion coefficient of ≤-0.2×10^-5/°C, a degree of shrinkage when held at 80°C for 24 hours under no tension of ≤0.05% and a width of ≥150 mm and a thickness of ≥0.3 mm.
    引張弾性率が9.0GPa以上、線膨張係数が−0.2×10^-5/℃以下、無張力下で80℃、24時間保持した際の収縮率が0.05%以下であり、幅が150mm以上、厚さが0.3mm以上であることを特徴とする延伸熱可塑性ポリエステル系樹脂シート。 - 特許庁
  • The polishing section of the pad is formed by a foamed body whose material is synthetic resin having 100% modulus defined by JIS K7113 that is equal to or less than 11.8 MPa (120 kgf/cm^2) and a maximum height of the surface (Rmax) set by JIS B0601-1982 is equal to or less than 70 μm.
    この研磨パッドの研磨部は、JIS K7113に規定される100%モジュラスが11.8MPa(120kgf/cm^2)以下の合成樹脂を材料とする発泡体で形成されており、その表面のJIS B0601−1982に規定される最大高さ(Rmax)は、70μm以下である。 - 特許庁
  • The water-based ink for a ballpoint pen has a value A in the range of -0.3 to 0.3 in an approximate linear formula of Y=AlnX+B in X in a range of 0.1 Pa to 1.0 Pa when the ink comprises a xanthan gum and an N-acylamino acid amine, stress is X and the complex modulus of elasticity of the ink is Y.
    キサンタンガムとN−アシルアミノ酸アミンを添加し、応力をX、インキの複素弾性率をYとしたとき、Xが0.1Paから1.0Paの範囲で、Y=AlnX+Bの近似直線式においてAの値が−0.3から0.3の範囲である、ボールペン用水性インキ。 - 特許庁
  • To provide a curable composition and a sealing material composition each of which can easily be produced, has good storage stability, is moisture- cured to give a rubber-like elastic material having a high tensile strength and a low modulus with a high elongation, and is excellent in adhesiveness, weatherability, heat resistance, and durability e.g. water resistance in particular.
    製造し易く、保存安定性の良い、湿気硬化して高い引張り強度と低モジュラスで大きな伸びを有するゴム状弾性体となる、接着性、耐候性、耐熱性、特に耐水性などの耐久性に優れた硬化性組成物及びシーリング材組成物を提供する。 - 特許庁
  • To provide a composite polylactic acid-based thermoplastic resin composition that shortens a molding cycle by enhancing a crystallization rate of polylactic acid, and improves physical properties such as heat resistance, impact resistance and an elastic modulus with sufficient balance, as well as furthermore enables good molding appearance to be obtained.
    ポリ乳酸の結晶化速度を向上させて成形サイクルを短縮すると共に、耐熱性、耐衝撃強度、弾性率等の物性をバランスよく改善し、更には良好な成形品外観が得られる複合ポリ乳酸系熱可塑性樹脂組成物を提供する。 - 特許庁
  • This acrylic resin composition is characterized by comprising an acrylic resin, a granular additive having an elastic modulus which is 15% or less of that of the acrylic resin and an inorganic filler subjected to a surface treatment with an isocyanate having at least one type of functional group selected from a methacryloyloxy group, an acryloyloxy group and a vinyl group.
    アクリル樹脂と、弾性率がアクリル樹脂の15%以下である粒状添加剤と、メタクリロイルオキシ基、アクリロイルオキシ基、およびビニル基から選ばれる少なくとも1種の官能基を有するイソシアネートで表面処理した無機充填材とを含有することを特徴とする。 - 特許庁
  • The semiconductor device is so formed on at least a single-sized surface of a semiconductor wafer wherein the polyimide layer having a tensile elastic modulus not smaller than 4 GPa, a linear expansion coefficient not larger than 25 ppm, and a moisture absorbing expansion coefficient not larger than 35 ppm is formed directly as to form its functional elements on at least a single-sized surface of the semiconductor wafer.
    少なくとも片面に機能素子が形成された半導体ウエハの少なくとも片面に、引張弾性率が4GPa以上、線膨張係数が25ppm以下、吸湿膨張係数が35ppm以下のポリイミド層を直接形成した半導体装置。 - 特許庁
  • The Fe-based amorphous alloy contains at least Fe, M (at least one kind selected from among Sn, In and Zn), P and C, has a Vickers hardness (Hv) of ≤885, a tensile strength of 200 to 360 (MPa), a Young's modulus of 35 to 60 (MPa) and an elongation (strain) of ≥0.3%.
    Fe基非晶質合金は、少なくともFe、M(Sn,In,Znの少なくともいずれか1種)、P及びCを有し、ビッカース硬さ(Hv)が885以下で、引張強度が200〜360(MPa)で、ヤング率が35〜60(MPa)、伸び(歪み)が0.3%以上である特性を備えている。 - 特許庁
  • The hard coat treated article formed by laminating a hard coat layer on at least the single surface of a substrate, for example, the hard coat film wherein the surface elastic modulus of the hard coat layer is 4.5 GPa or more and the thickness of the hard coat layer is 5% or more of the total thickness of the film is 5% or more is cut by irradiation with a laser beam.
    基材の少なくとも片面にハードコート層を積層してなるハードコート処理物品、例えば、ハードコート層の表面弾性率を4.5GPa以上、ハードコート層の厚みがフィルム総厚の5%以上であるハードコートフィルムをレーザー照射により裁切断する。 - 特許庁
  • According to the present invention, the polybenzazole film can be obtained, which has surface roughness (Ra, arithmetic average roughness) of 40 nm or less, a ratio of tensile strength in a vertical direction and in a lateral direction of 0.80 or more, and a ratio of tensile modulus of elasticity in a vertical direction and in a lateral direction of 0.80 or more.
    本発明によれば表面あらさ(Ra、算術平均粗さ)が40nm以下であり、かつ、縦方向と横方向の引張強さの比が0.80以上であり、縦方向と横方向の引張弾性率の比が0.80以上であるポリベンザゾールフィルムが得られる。 - 特許庁
  • The loss tangent tan δ and storage modulus E' (MPa) of rubber for a tire tread, and the contact area A(mm^2) of the entire contact surface of the tire when the rubber for the tire tread is pressed against the group of projections corresponding to irregularities of the road surface are measured at the temperature of at least two points of ≤0°C and ≥20°C.
    0℃以下及び20℃以上の少なくとも2点の温度で、タイヤトレッド用ゴムの損失正接 tanδと貯蔵弾性率E’(MPa)、及び路面の凹凸に対応する突起群にタイヤトレッド用ゴムを押し付けた時の予測タイヤの接地面全体の接触面積A(mm^2 )を測定する。 - 特許庁
  • The outer ring 11, the inner ring 12 and the roller 13 consist of the sintered body comprising the β-sialon as the main component, represented by compositional formula of Si_6-zAl_zO_zN_8-z and satisfying 0.1≤z≤3.5, and remaining impurities, and Young's modulus is 180 GPa or more and 270 GPa or less.
    そして、外輪11、内輪12およびころ13は、Si_6−ZAl_ZO_ZN_8−Zの組成式で表され、0.1≦z≦3.5を満たすβサイアロンを主成分とし、残部不純物からなる焼結体から構成され、ヤング率が180GPa以上270GPa以下である。 - 特許庁
  • In the equation (1), P is the outer diameter of a shaft body 2, L is the axial length of the roll body 6, E is the vertical elastic modulus of the shaft body 2, I is the sectional secondary moment of the shaft body, and R is a single-side load for pressing the roll 1 to the contact object.
    y=(P/9)^2Rx(x^3−2Lx^2+L^3)/(6EIL)・・・(1)但し(1)式において、Pは軸体2の外径、Lはロール体6の軸方向の長さ、Eは軸体2の縦弾性係数、Iは軸体の断面二次モーメント、Rはロール1を被当接物に押し当てる片側荷重である。 - 特許庁
  • Printing is effected under a condition that the block copy sheet, whose surface of at least one side is constituted of a material showing an elastic modulus of 500 kg/cm^2 or less at 20°C, is interposed between the plate cylinder and the lithographic printing plate, at least whose rear surface is constituted of a material other than metal.
    版下シートの少なくとも片面の表面が、20℃のもとで500kg/cm^2以下の弾性率を示す材料から構成されている平版印刷用版下シートを、版胴と、少なくとも裏面が金属以外の材料からなる平版印刷版との間に介在させて印刷する。 - 特許庁
  • To obtain a vibration-insulating rubber composition for an automobile having vibration-insulating characteristics characterized in a loss tangent (tan δ) of at least 0.3 (which means a comfortable car driving) and a dynamic-to- static modulus ratio of not more than 2.5 (which means a low noise in vehicles) and remarkably excellent heat resistance without injuring molding processability.
    損失正接(tanδ)が0.3以上(自動車の乗り心地が良好)で、動倍率2.5以下(車内騒音が少ない)の防振特性を有し、耐熱性に著しく優れ、成形加工性を損なわせない自動車用防振ゴム組成物を提供すること。 - 特許庁
  • To provide a method for producing a polyester fiber that has a high spinning speed at break, high productivity, a little fluff occurrence, a high strength, a low load elongation (high coefficient of elasticity, high modulus), small variations of physical properties such as strength, elongation, etc., and a low dry heat shrinkage ratio.
    本発明の課題は、破断紡糸速度が高く高生産性が可能であり、毛羽発生が少なく、高強度、低荷伸(高弾性率、高モジュラス)、強伸度等の物性のバラツキが小さく、低乾熱収縮率のポリエステル繊維の製造方法を提供することにある。 - 特許庁
  • To provide a manufacturing method for a metal mask which makes the crystal carry a fine crystal structure by manufacturing the metal mask by a plating bath composition loaded with a citrate in stead of a boric acid as an additive to a sulfamate nickel bath, increases the hardness, the surface roughness and the Young's modulus, and in addition, is environment friendly.
    スルファミン酸ニッケル浴に添加剤としてホウ酸の代わりにクエン酸塩を添加したメッキ浴組成で、メタルマスクを製造することにより、結晶が微細結晶構造となり、硬度と表面粗さとヤング率が向上し、しかも環境にもやさしいメタルマスクの製造方法を得る。 - 特許庁
  • The pneumatic radial tire has a chafer comprising a rubber composition having complex modulus of elasticity of 9-13 MPa measured under the condition of temperature of 70°C, frequency of 10 Hz and dynamic distortion of ±2%, tangent loss of 0.08-0.11 and tensile elongation measured according to JIS-K6251 of 230%.
    温度70℃、周波数10Hzおよび動歪±2%の条件で測定される複素弾性率が9〜13MPa、損失正接が0.08〜0.11、かつJIS−K6251に準じて測定される引張伸びが230%以上であるゴム組成物からなるチェーファーを有する空気入りラジアルタイヤ。 - 特許庁
  • In this dicing/die-bonding film 10 with an adhesive layer 2 and a die-sticking adhesive layer 3 sequentially laminated on a support base material 1, the thickness of the adhesive layer 2 is 10-80 μm, and the storage modulus thereof at 23°C is 1×10^4 to 1×10^10 Pa.
    支持基材1上に粘着剤層2及びダイ接着用接着剤層3が順次積層されたダイシング・ダイボンドフィルム10であって、前記粘着剤層2の厚みが10〜80μmであり、23℃に於ける貯蔵弾性率が1×10^4〜1×10^10Paであることを特徴とする。 - 特許庁
  • To provide a one-pack type moisture-curable composition having a low viscosity, becoming a rubbery elastic material having a low modulus and a large elongation by moisture curing, easy to be produced, having a good workability, especially exhibiting a good weather resistance and excellent in adhering property, etc., and a sealing material composition.
    水分硬化により低モジュラスで大きな伸びを有するゴム状弾性体となる、製造し易く、作業性の良い、特に耐候性が良好で、接着性などに優れた低粘度の一液湿気硬化型の硬化性組成物及びシーリング材組成物を提供する。 - 特許庁
  • Especially, it is preferable that the fluororesin mold-released layer is PFA, its melt flow rate is ≤10g/10 minute, and the inside diameter accuracy of the belt is ≤1% as the coefficient of variation, the rupture strength of the belt is ≥130N and the elastic modulus thereof is ≥4000Mpa.
    特に、前記フッ素樹脂離型層がPFAであることやメルトフロレート10g/10分以下であること、またベルトの内径精度が変動係数で1%以下であること、ベルトの破断強度が130N以上、弾性率4000Mpa以上であることが好適である。 - 特許庁
  • This prism sheet can be obtained by covering the flat surface of a transparent base material film where unit prism or unit lens is formed on one side surface thereof and the other side surface is flattened with a layer consisting of light-transmissive material having tensile elastic modulus of 0.5-2500 MPa or a layer consisting of polyurethane.
    一方の面に単位プリズム又は単位レンズが形成され、他方の面は平らにされた透明基材フィルムの、その平らな面に引張弾性率0.5〜2500MPaの透光性材料からなる層又はポリウレタンからなる層を被覆させてプリズムシートを得る。 - 特許庁
  • This gong is made of a material, wherein a square root of a ratio of elasticity modulus of the material divided by a volume mass of the material is less than 3300 m/s, so as to allow the gong to produce a rich sound, comprising a large number of partials, within the audible frequency range.
    ゴングが製作される材料は、選択された該材料の容積質量で除算した材料の弾性係数の比の平方根の値が3300m/sよりも小さく、可聴周波数範囲内で多数の部分音を含む豊かな音をゴングが発生できるようにする。 - 特許庁
  • To provide an epoxy resin composition achieving flame retardancy of the UL94V-0 level with halogen-free compounds, substantially suppressing lowering of the elastic modulus in the high-temperature range equal to or higher than the glass transition temperature and permitting formation of laminates having high flame retardancy, heat resistance and joining reliability.
    ハロゲンフリー化合物でUL94V−0難燃性を達成し、且つガラス転移温度以上の高温領域に於ける弾性率の低下も大幅に抑制して、難燃性と耐熱性および接合信頼性に優れた積層板を得ることの出来る、エポキシ樹脂組成物を提供する。 - 特許庁
  • The double-coated pressure-sensitive adhesive sheet comprises a shrinkable substrate, an energy ray-curable pressure-sensitive adhesive layer formed on one side of the substrate, and a pressure-sensitive adhesive layer having an elastic modulus at 120°C of 5×10^5 Pa or lower and formed on the other side of the substrate.
    本発明に係る両面粘着シートは、収縮性基材と、該基材の一方の面にエネルギー線硬化型粘着剤層、反対面に120℃における弾性率が5×10^5Pa以下の粘着剤からなる再剥離性粘着剤層が設けられていることを特徴としている。 - 特許庁
  • The low thermal expansion ceramic mainly includes cordierite and contains 0.1-10 wt.% Ti expressed in terms of oxide and 1-20 wt.% rare earth element expressed in terms of oxide and has ≤1×10^-6/°C thermal expansion coefficient at 10-40°C, ≥95% relative density and ≥100 GPa Young's modulus.
    コージェライトを主体とし、Tiを酸化物換算で0.1〜10重量%含有し、希土類元素を酸化物換算で1〜20重量%含有してなり、10〜40℃における熱膨張率が1×10^−6/℃以下、相対密度が95%以上、ヤング率が100GPa以上である。 - 特許庁
  • This laminated body at least has the resin layer (A) including a propylene resin (a), a resin layer (B) including an acrylic resin (b) having a flexural modulus of 100 MPa or more to 1,500 MPa or less and a resin layer (C) including an acrylic resin (c) in the order of the resin layers (A), (B) and (C).
    プロピレン系樹脂(a)を含む樹脂層(A)、100MPa以上1500MPa以下の曲げ弾性率を有するアクリル系樹脂(b)を含む樹脂層(B)、及びアクリル系樹脂(c)を含む樹脂層(C)を少なくとも有し、該樹脂層(A)、(B)及び(C)がこの順序で積層されている積層体。 - 特許庁
  • The modulus of elasticity is varied to vary the spring constant of the suspension bushing 10 by varying the potential difference of both the clamped end surfaces of the electric responsive elastic member 32 according to the contacting/leaving state of the first member 28 and the second member 30 detected by the contact element 34.
    接触子34が検出する第1部材28と第2部材30の接離状態に応じて電気応答性弾性部材32の挟持両端面の電位差を変化させることにより弾性率を変化させてサスペンションブッシュ10のばね定数を変化させる。 - 特許庁
  • A double end support beam 1 of which the beam height changes so that a section modulus lessens toward the central part from the opposite end parts is provided by reducing the lower side 5 of the double end support beam 1 by a length being equal to or larger than the deflection length of each part thereof.
    両端部から中央部にかけて断面係数が小さくなるようにはり高さが変化した両端支持ばり1であって、両端支持ばり1の下辺5側を、両端支持ばり1の各部のたわみ長さ以上の長さで縮小させることによって、上記の課題を解決する。 - 特許庁
  • To provide an outer layer for a rolling roll having excellent wear resistance and rough surface resistance, capable of suppressing flattening of the roll by providing a high modulus of longitudinal elasticity to the outer layer, excellent in rolling consistency, and relatively low in manufacturing cost, and a rolling roll using the same.
    優れた耐摩耗性および耐肌荒れ性を具備するとともに、外層材に高い縦弾性係数を付与することによりロールの偏平を抑制し、圧延の安定性に優れ、製造コストが比較的安価なた圧延ロール用外層材およびそれを用いた圧延ロールを提供する。 - 特許庁
  • Concretely, thicknesses of a thermoplastic material 18 and a connection member 19 on the side A are enlarged or in an A-side area, a part (extension portion 19a) of the connection member 19 having an elastic modulus higher than that of the thermoplastic material 19 is provided while extending to the middle of a magnetic gap 15.
    具体的には、A側の熱可塑材18と連結部材19の厚みを大きくしたり、A側の領域において、熱可塑材18よりも弾性率が高い部材である連結部材19の一部(延長部19a)を磁気間隙15中まで達するように延長して設ける。 - 特許庁
  • The system is configured to focus a laser beam on an inside of the workpiece 1 that is to be an oscillation section of the oscillation part, to form an internally transformed layer 4 inside the workpiece 1, and to control the oscillation frequency by utilizing changes in elastic modulus of the workpiece 1 by the internally transformed layer 4.
    レーザ光の焦点を振動部品の振動部となる加工対象物1内部に合わせ、加工対象物1の内部に内部変質層4を形成し、この内部変質層4による加工対象物1の弾性係数の変化を利用して振動周波数を調整する構成とする。 - 特許庁
  • A butterfly damper supporting a voice coil bobbin of a speaker so as to oscillate, on a frame, is molded, using an olefinic resin material having physical values: internal loss of 0.045 or more, tensile strength of 200% or more and modulus of bending elasticity of 300 MPa or more.
    スピーカのボイスコイルボビンをフレームに対して振動自在に支持する蝶ダンパにおいて、この蝶ダンパが、内部損失が0.045以上,引張り強度が200%以上,曲げ弾性率が300Mpa以上の物性値を有しているオレフィン系樹脂材料によって成形されている。 - 特許庁
  • These materials are characterized by having a dielectric constant (k) of about 3.7 or less, a normalized wall elastic modulus (E_0'), derived in part from the dielectric constant of the material, of about 15 GPa or greater, and a metal impurity level of about 500 ppm or less.
    これらの材料は、約3.7又はそれ未満の誘電率(k)、前記材料の誘電率から部分的に導出される約15GPa又はそれよりも大きい標準化壁体弾性率(E_o′)、及び金属不純物レベルが500ppm又はそれ未満のものとして特徴づけられる。 - 特許庁
  • The thermal ink jet head has a barrier wall for introducing ink to heating elements wherein polyamideimide resin, preferably having a modulus of elasticity in tension of 400 kg/mm2 or above and a coefficient of thermal expansion of 4×10-5 [1/°C], is employed as the material of the barrier wall.
    発熱素子にインクを導くための隔壁を有するサーマル型インクジェットヘッドであって、前記隔壁材料として、好ましくは引っ張り弾性率が400kg/mm^2以上、好ましくは熱膨張係数4×10^-5[1/℃]以下のポリアミドイミド樹脂を用いることを特徴とするサーマル型インクジェットヘッド。 - 特許庁
  • The elastic crossbar includes a crossbar body (11) crossing rails (R1, R2), and elastic materials (12A, 12B, 13A, 13B) which are attached to the end faces (11a1, 11b1) of the crossbar body (11) in the direction of crossing the rails (R1, R2) and have an elastic modulus smaller than that of the crossbar body (11).
    レール(R1、R2)を横切るまくらぎ本体(11)と、まくらぎ本体(11)のレール(R1、R2)を横切る方向の端面(11a1、11b1)に取り付けられると共にまくらぎ本体(11、13)より弾性係数について小さな弾性材(12A、12B、13A、13B)とを有する。 - 特許庁
  • The stamper includes a plate-like body having a Young's modulus of not less than 50 to not more than 500 GPa, a thickness of not less than 200 to not more than 1,000 μm, and a warp with a curvature of not less than 2×10^-5 to not more than 2×10^-3, and a fine structure pattern to be transferred is mounted on one surface.
    ヤング率が50GPa以上500Gpa以下、厚さが200μm以上1000μm以下であって、曲率が2×10^-5以上2×10^-3以下である反りを有する板状体からなり、その一面に転写すべき微細構造パターンが設けられているスタンパ。 - 特許庁
  • To provide a method for forming a coating film, which is hardly peeled, has a scratch strength of 100 N or more without depending on the number of layers, has the controllable Young's modulus and controllable hardness and the like by changing intervals of layers or ratios of layers, and almost free from defects such as chipping and partial cracks.
    剥離し難く、かつ積層数に依存することなく、100N以上のスクラッチ強度を有し、積層間隔ならびに層比率を変化させることで、ヤング率、硬度などを制御でき、チッピング、部分クラックなどの欠けはほとんど生じない被膜形成方法を提供する。 - 特許庁
  • In the polyolefin microporous film, when the tensile modulus of elasticity in a machine direction and in a machine vertical direction are set to E_MD and E_TD, respectively, E_MD is 75-200 N; and E_MD/E_TD is 1.3-3.0; and the bending resistance is set at 0.010-0.060 (mN cm).
    機械方向と機械垂直方向における引張弾性率をそれぞれE_MDとE_TDとした時、E_MDが75〜200Nであり、E_MD/E_TDが1.3〜3.0であり、剛軟度が0.010〜0.060mN・cmであることを特徴とするポリオレフィン微多孔膜。 - 特許庁
  • The ski plate is equipped with a base material 21 of a synthetic resin which forms a recessed part 22 at the center part of the bottom surface in the longitudinal direction, and with a reinforcement plate 25 of a material having higher Young's modulus than that of the synthetic resin which then is formed in an approximate same shape and fitted and fixed onto the recessed part of the base material.
    下面の長手方向中央部に凹部22を形成した合成樹脂製の基材21と、該基材の上記凹部に嵌合固定した、該凹部と略同一形状で上記合成樹脂よりヤング率が高い材料からなる補強板25と、を備える。 - 特許庁
  • The self-adhesive tape comprises a supporting layer 13 made of a polyolefin resin and used also as a release layer, a flexible base material layer 11 made of a thermoplastic urethane elastomer, a printed layer 21, and a self-adhesive layer 19, wherein the flexible base material layer 11 has a 100% modulus of ≤15 MPa.
    ポリオレフィン系樹脂からなり、かつ剥離層を兼ねる支持層13、熱可塑性ウレタンエラストマーからなる柔軟性基材層11、印刷層21、及び粘着層19からなることを特徴とし、柔軟性基材層11の100%モジュラスが15MPa以下であることも特徴とする。 - 特許庁
  • The pneumatic tire also includes a first rubber layer arranged on a tire surface between a tire maximal width position and the tread part whose tanδ at 20°C is higher than that of side rubber, and a second rubber layer arranged inward of the tire from the side rubber whose 100% modulus is higher than that of the side rubber.
    この空気入りタイヤは、タイヤ最大幅位置とトレッド部との間のタイヤ表面に設けられる、20℃におけるtanδがサイドゴムよりも高い第1ゴム層と、前記サイドゴムよりもタイヤ内側に設けられる、100%モジュラスが前記サイドゴムよりも高い第2ゴム層と、を備える。 - 特許庁
  • To provide an energy ray-curable resin composition for a resin mold suitable to mass production of lens sheets at low cost by molding an ultraviolet-curable resin or a thermoplastic resin, which gives a cured product with a high glass transition temperature (Tg), a high storage elastic modulus, a low shrinkage factor at curing, and excellent durability.
    紫外線硬化型樹脂または熱可塑性樹脂を成型するレンズシートの低コストでの量産作製に好適な、ガラス転移温度(Tg)、貯蔵弾性率が高く、硬化収縮率の低い、耐久性に優れた樹脂型用エネルギー線硬化型樹脂組成物の提供。 - 特許庁
  • To provide a polyolefin-based thin film multilayered shrink film excellent in characteristic balance such as a high tensile elastic modulus, a high thermal shrinkage factor, high tear strength and small shrinkage with time, in spite of its thin thickness of 6-11 μm, and suitably used for high speed automatic packaging and printing.
    厚みは6〜11μと薄いにもかかわらず、高引張弾性率、高熱収縮率、高引裂強度、及び経時収縮が小さい等の特性バランスが優れ、高速自動包装や印刷に好適に用いられるポリオレフィン系薄膜多層シュリンクフィルムを提供する。 - 特許庁
  • The self-adhesive tape comprises a supporting layer 13 made of a polyolefin resin and used also as a release layer, a flexible base material layer 11 made of a thermoplastic acrylic elastomer, a printed layer 21, and a self-adhesive layer 19, wherein the flexible base material layer 11 has a 100% modulus of ≤15 MPa.
    ポリオレフィン系樹脂からなり、かつ剥離層を兼ねる支持層13、熱可塑性アクリルエラストマーからなる柔軟性基材層11、印刷層21、及び粘着層19からなることを特徴とし、柔軟性基材層11の100%モジュラスが15MPa以下であることも特徴とする。 - 特許庁
  • The modulus of elasticity can be reduced for increasing the thickness of an intermediate part of a face, by arranging the auxiliary unit 20 on the back face of the face unit 10 by a frictional welding or brazing joining method, by molding the club head face unit 10 by bending a plate material.
    板材を折り曲げてクラブヘッドフェイスユニット10を成型し、摩擦熔接またはろう付け接合方法によりフェイスユニット10の背面に補助ユニット20を配置することにより、フェイスの中間部位の厚さを増加させるため、弾性係数を減少させることが可能である。 - 特許庁
<前へ 1 2 .... 78 79 80 81 82 83 84 85 86 .... 98 99 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.