To activate a stress given in the gate width direction in a channel region toward the direction of increasing the mobility, and to prevent a leakage when a silicide layer is formed on the surface of a source drain region. チャネル領域のゲート幅方向に与える応力を移動度が向上する方向に働かすとともに、ソース・ドレイン領域表面にシリサイド層を形成した際のリークを防止する。 - 特許庁
To reduce read average time and also to reduce a stress to be applied on a memory cell when a shift of the threshold voltage caused by an interference between cells does not affect reading. セル間干渉によるしきい値電圧のシフトの影響を受けない読み出しを行うに際して、読み出しの平均的時間を短縮すると共に、メモリセルへ加わるストレスを低減する。 - 特許庁
As a result, the end housing 40 can be fixed to the yoke 28 without residual stress in the housing without needing particular equipment and processes and without applying pressure in the axial direction. したがって、エンドハウジング40を特別な設備や工程を必要とすることなく、且つ、軸方向の圧力を掛けることなく、応力を残留させないでヨーク28に固定できる。 - 特許庁
To provide a low cost toroidal type continuously variable transmission of a structure easy to machine without deteriorating proof stress of an input shaft, supplying lubricating oil to a ball spline groove satisfactorily. 入力軸の耐力を低下させることなく且つ加工が容易な構造形態で、ボールスプライン溝に潤滑油を良好に供給できる安価なトロイダル型無段変速機の提供する。 - 特許庁
To provide a bobbin for POF heat treatment that reduces stress applied to a POF during a heat treatment and also to provide a method for manufacturing the POF by using the bobbin. 熱処理中に、POFに加わる応力を減少させることができるPOF熱処理用ボビンおよびこのようなボビンを使用したPOFの製造方法を提供すること。 - 特許庁
The jig 10 for stress corrosion cracking test has both a ceiling 18 for supporting both ends of a test piece 20 from above and an intermediate point support part 12 for supporting a center part of the test piece from below. 応力腐食割れ試験用ジグ10は、試験片20の両端を上側から支持する天壁18と、試験片の中心部を下側から支持する中点支持部12を有する。 - 特許庁
The first disk part 23 mounted to the machine body and applied with a strong force is made thicker than the second disk part 21 radially outside thereof, so that deformation due to stress or the like can be prevented. 機体へ装着されて大きな力のかかる第1ディスク部23を、半径方向外側の第2ディスク部21よりも厚くしたので、応力等による変形を防止することができる。 - 特許庁
To instantly disable a transmission side control part when a power source on a receipt side control part is turned off for reducing electric stress working on the receipt side control part and improving destruction resistance performance. 受信側制御部の電源オフ時に送信側制御部を即時にディセーブルにして受信側制御部にかかる電気的ストレスを低減して耐破壊性能を向上させる。 - 特許庁
On the contrary, when the accelerator opening time change amount ΔAPO/Δt is greater (Yes in Step S1), target engine torque is restricted (Step S3) and down-shift is performed (Step S4) to reduce the operating stress of the belt 19. これに対しアクセル開度時間変化量ΔAPO/Δtが大きいとき(ステップS1でYes)、目標エンジントルクを制限し(ステップS3)、ダウンシフトを行って(ステップS4)、ベルト19の作用応力を小さくする。 - 特許庁
To prevent excessive stress from being given to a switching element of an inverter, in a discharge lamp lighting device for dimming light by controlling the frequency of the inverter and a dc power supply voltage. インバータの周波数と直流電源電圧を制御して調光する放電灯点灯装置において、インバータのスイッチング素子に過大なストレスを与えることを防止する。 - 特許庁
In case change takes place in ground forming the bluff in this state, power P is applied to the member 1 owing to the changed, and stress by the power P is accumulated in the element 2. この状態で例えば崖を形成する地盤に変化が生じると、この変化によりセンサ部材1に力Pが加わり、センサ素子2にはこの力Pによる応力が蓄積する。 - 特許庁
To prevent a coated crimp portion of a crimp terminal from shifting or coming off from an insulation coating of an electric wire due to stress applied on the electric wire, in an electric wire with a terminal. 端子付電線において、圧着端子の被覆圧着部が、電線に加わる応力に起因して電線の絶縁被覆に対してずれる又は外れることを防止すること。 - 特許庁
To provide a mesh fence capable of facilitating the formation of impressive patterns in a fence surface, facilitating the diversification of the patterns and making weight reduction by decreasing a horizontal wire rod without concentrating stress to a folding place. フェンス面に印象的な模様を形成し易く、その模様の多様化も容易で、屈曲箇所に応力を集中させず、横線材を減少させて軽量化を可能にする。 - 特許庁
To provide a dielectric barrier discharge lamp device improved so as not to generate a deflection of an air tight container or inconvenience due to thermal stress and an ultravaiolet ray irradiation device using the lamp device. 気密容器の撓みや熱ストレスによる不都合が生じないように改良された誘電体バリヤ放電ランプ装置およびこれを用いた紫外線照射装置を提供する。 - 特許庁
In the sensor unit, four post members 31 of spacer 30 are bent at a slit 33 so as to absorb stress generated at thermal-expansion in a direction to expand a space between circuit boards 10, 20. センサユニットでは、スペーサ30の4本の柱部材31が、回路基板10、20の間を広げる方向に熱膨張する際に生じる応力を吸収するようにスリット33で撓む。 - 特許庁
This structure allows a portion of stress accompanying thermal expansion and generated between the substrate 31C and the conductors 31A and 31B to be absorbed by the multiple notches even under a high temperature environment. これにより、高温環境下であっても熱膨張に伴う基板31Cと導体31A,32Bとの間に発生する応力の一部が、複数のスリットにおいて吸収される。 - 特許庁
To provide an adapter for an optical disk which eliminates a defect caused by birefringence due to uneven stress applied in the radial direction of the optical disk, and realizes good reproduction and good recording. 光ディスクの半径方向に加わる不均一な応力による複屈折に起因する不具合を解消し、良好な再生及び記録を実現する光ディスク用アダプタを提供する。 - 特許庁
(B) When the kneaded product of the cosmetic after evaporation of moisture is in a grease state or in a semi-solid state, a first normal stress difference N_1 is measured as the rheology characteristics after kneading. (B)水分を揮発させた後の該化粧料を混練物がグリース状又は餅状を呈しているときには、混練後にレオロジー特性として第1法線応力差N_1を測定する。 - 特許庁
The end in the longitudinal direction of a glass roll body formed by winding a thin sheet glass into a roll shape is a cleft surface by thermal stress over the whole thickness thereof. 本発明は、薄板ガラスをロール状に巻回してなるガラスロール本体の長手方向端部がその全厚にわたり熱応力による割断面とされてなることを特徴とする。 - 特許庁
To provide a pressure sensor capable of suppressing reduction of bond strength caused by a spark, and effectively preventing a stress by deformation of a gel member from applying to a diaphragm. スパークによる接合強度の低下を抑制するとともに、ゲル部材の変形による応力がダイアフラムに作用するのを効果的に抑制することのできる圧力センサを提供する。 - 特許庁
Even when the connection pin 15 is pushed in by the ultrasonic vibrator 10's being pushed from outside, a stress generated at that time can be absorbed by the insert pin 21, thereby. これにより、超音波振動子10が外部から押されることで接続ピン15が押し込まれても、そのとき発生する応力をインサートピン21にて吸収することが可能となる。 - 特許庁
To provide a ceramic electronic component hardly influenced by stress generated when forming an external electrode formed of a metal sintered compact at the end of a ceramic component body, and to provide a method for manufacturing the same. セラミック部品本体の端部に金属焼結体からなる外部電極を形成するときに発生する応力による影響の少ないセラミック電子部品と、その製造方法を得る。 - 特許庁
To provide a liquid supply controlling device enabling adequate evaluation of water stress conditions even when a leaf projection area is temporarily reduced due to a cause such as leaf cut. 本発明は、葉かき等の要因により葉の投影面積に一時的減少があっても正確に水ストレス状態を評価できる給液制御装置を提供することを目的とする。 - 特許庁
To decrease a characteristic change due to temperature by relaxing a tightening stress caused by an outer package resin while keeping a function of damping an internal piezoelectric element. 内部の圧電素子をダンピングする機能を維持したまま、外装樹脂からの締め付け応力を緩和し、温度による特性変化の少ない圧電部品およびその製造方法を提供する。 - 特許庁
To provide a heat pump type water heater that prolongs service life of a compressor by reducing an operational stress on the compressor and prevents occurrence of a 'hot water outage' phenomenon. 圧縮機の運転ストレスを低下させて圧縮機の長寿命化を図ることが可能で、しかも「湯切れ」現象の発生を防止することができるヒートポンプ式給湯装置を提供する。 - 特許庁
To distinguish a restart mode in recovery from an instantaneous power failure from a normal start or restart mode to prevent stress from being imposed on a circuit in the overall operation. 動作全般において回路にストレスが加わるのを防止するように、瞬時停電後の復電時の再始動モードと通常の始動又は再始動モードとの切り分けを可能にする。 - 特許庁
To provide an optical head device in which excessive stress is not exerted to a device frame even when a composition is adopted in which a flexible substrate is sandwiched between the device frame and a metal cover. 装置フレームと金属カバーとの間に可撓性基板を挟んだ構成を採用した場合でも、装置フレームに過大な応力が加わることのない光ヘッド装置を提供すること。 - 特許庁
To provide a saddle structure by which a cable is not corner-folded at an exit part of the saddle structure, and excessive bending stress is not applied to a straight pipe part of an inner pipe. サドル構造体の出口部においてケーブルが角折れすることなく、内管の直管部に過大な曲げ応力が作用することのない構造を有するサドル構造体を提供する。 - 特許庁
To measure the amount of thermal fatigue stress in the market, to replace or correct components in reproduction without any leakage, and to prevent components remaining to be used from being replaced unnecessarily. 市場での熱疲労ストレス量を測定でき、また、再生する場合は部品交換や修正を漏れがなく実施できるとともに、まだ使える部品を不必要に交換しない。 - 特許庁
To provide a massage machine prevented from giving a user stress as much as possible even if the user unconsciously selects a course including an air massage by an arm retaining member. 使用者が無意識に腕保持部材によるエアマッサージが含まれるコースを選択した場合でも、使用者にストレスを与えることを可及的に防止し得るマッサージ機を提供する。 - 特許庁
To provide an impact wrench having an improved anvil wherein a stress concentration part is eliminated and the life of the anvil is extended, while costs related to its manufacture are reduced. 応力集中部を除去し、金床の寿命を延ばし、一方で、同時にその製造に関連する費用を低減する、改善された金床を有するインパクトレンチを提供する。 - 特許庁
To provide a semiconductor light-emitting element capable of efficiently radiating heat and obtaining high reliability by releasing a thermal stress, and to provide a manufacturing method thereof and a light-emitting apparatus employing the same. 熱放散を効率よく行うことができ、熱応力を緩和して高い信頼性を得ることができる半導体発光素子およびその製造方法、並びに発光装置を提供する。 - 特許庁
To provide a simple-structure and excellent-practicality touch panel that is a resistance film type touch panel, sensing stress of a press as well as a position of a pressing finger (or pen). 抵抗膜式タッチパネルであって、押圧した指(またはペン)の位置のみならず、押圧の応力を感知することができる、構造が簡単で実用性に優れたタッチパネルを提供する。 - 特許庁
To obtain a structure that can reduce the stress concentration of corners 7a, 7a of each pocket 5a, and can improve the plane precision of internal faces 4a, 4a of rims 2a, 2a. 各ポケット5aの隅部7a、7aの応力集中を軽減できると共に、リム部2a、2aの内側面4a、4aの面精度を向上させる事が可能な構造を実現する。 - 特許庁
The sealing rubber 20 is rectangular surrounding an image sensing region, and has a cut-out portion 24 at four corners thereof for removing stress generated due to compression by the CCD 11 and the lens. シールゴム20は、撮像領域を囲む矩形状であり、その四隅に、CCD11およびレンズによって圧縮されることによって生じる応力を逃がす切欠き部24を有する。 - 特許庁
To provide a card with built-in semiconductor and capable of suppressing separation between a semiconductor mounting board and a card frame to a high degree when a bending stress is applied while satisfying the requirement of reduction in size and thickness. 小型・薄型化の要請に応えつつ、曲げ応力が負荷された際の半導体実装基板とカードフレームとの間の剥離を高度に抑制した半導体内蔵カードを提供する。 - 特許庁
To suppress kinks and wrinkles caused by stress resulting from a circumferential velocity difference between the end and the center in a longitudinal direction of a charging member, with much simpler configuration, without making the charging member large in size. より簡単な構成で、帯電部材が大型化することなく、長手端部と長手中央部の周速差により生じるストレスに起因するよれやしわを抑制すること。 - 特許庁
Thereby, since stress is applied to the diaphragm 14 upon operation to be dispersed into three inflection points P1, P2 and P3, durability of the diaphragm 14 can be enhanced. これにより、動作時のダイヤフラム14には、3つの変曲点P1,P2,P3に分散して応力が掛ることになるので、ダイヤフラム14の耐久性を大幅に向上させることができる。 - 特許庁
Therefore, concentration of stress to a portion producing depression or protrusion in the solid electrolyte 16 is avoided when the solid electrolyte 16 is formed on the flattening layer 20. 従って、この平坦化層20上に固体電解質16が設けられる際、該固体電解質16に陥没や隆起が生じてこれらの部位に応力が集中することが回避される。 - 特許庁
To provide a sham test piece for non-destructive inspection capable of easily and inexpensively obtaining a sham test piece having a grain boundary stress corrosion crack and a non-destructive inspection method applied to this technique. 粒界応力腐食割れを有する模擬試験体を容易且つ安価に得ることができる非破壊検査用模擬試験体及びこの技術を応用した非破壊検査方法の提供。 - 特許庁
To provide a stator of a rotary electric machine capable of preventing the generation of buckling in a split core by compression stress in a circumferential direction acting on the split core, and a manufacturing method of the same. 分割コアに作用した周方向の圧縮応力により分割コアに座屈が発生するのを防止し得るようにした回転電機の固定子及びその製造方法を提供する。 - 特許庁
To enhance reliability of connection by forming solder bumps in hand drum shape when an electronic component is mounted on a wiring board, thereby avoiding concentration of stress at the connecting part of solder bumps. 電子部品を配線基板に実装したとき、はんだバンプを鼓形に形成して、はんだバンプの接続部における応力の集中を回避して、接続の信頼性を向上させる。 - 特許庁
To prevent deflection of stress generated in a cage when an inner ring 12 is inserted into the cage 14 with conical rollers, in a conical roller bearing A using the synthetic resin cage 14. 合成樹脂製保持器14を使用した円すいころ軸受Aにおいて、円すいころ付きの保持器14に内輪12を挿入する際、その保持器内に生じる応力の偏位をなくす。 - 特許庁
To provide a technique which reduces stress at the time of using a tool for exclusive use to appreciate a picture which is not distinguished for a left eye or a right eye and is subjected to perspective emphasis processing. 左右眼用に区別されない画像であって、遠近感の強調処理が施された画像を、専用器具を用いて鑑賞するときのストレスを軽減する技術を提供する。 - 特許庁
To provide a packaging method and packaging structure of electronic components which can prevent the concentration of stress, for example, in the corners of an LSI mounted on a package substrate, and to provide the package substrate. 本発明は、例えばパッケージ基板のLSIの角部に応力が集中するのを防止できる電子部品の実装方法、実装構造及びパッケージ基板の提供を課題とする。 - 特許庁
To provide a block copolymer having both of high low-temperature shrinkage and high shrinkage stress and excellent in the balance of physical properties as a film, and to provide a heat shrinkable film therefrom. 低温高収縮性と高収縮応力性の両方を有し、且つフィルムとしての物性バランスに優れるブロック共重合体及びその熱収縮性フィルムを提供する。 - 特許庁
To provide a lined pipe in which stress concentration is prevented even if two opposite sides are not welded to absorb a dimensional tolerance when the bore is greater than a certain extent. 口径が大きくなって寸法公差を吸収するために対向する両辺の溶接を行わない場合においても応力が集中するのを防止したライニング管を提供する。 - 特許庁
To provide a digital/analog converter capable of prolonging a service life of a thin film element while reducing influences of current stress by approximately making uniform operating times of current cells. 各電流セルの作動時間を略均一とすることで、電流ストレスによる影響を低減して薄膜素子の寿命を延長させることのできるデジタル/アナログコンバータを提供する。 - 特許庁
To provide an image forming apparatus capable of achieving smooth operation of UI without temporarily stopping various jobs, even if the CPU throughput runs short and can relax the stress to users. CPUの処理能力が不足する場合であっても、各種ジョブを一時停止させることなく、UIのスムーズな動作を図り、ユーザへのストレスを緩和できる画像形成装置を提供する。 - 特許庁
To provide a micro-machine manufacturing method capable of reducing internal stress generated in a polysilicone layer having a predetermined thickness when flattening a recessed part in the polysilicone layer. 所定の厚みのポリシリコン層で凹部を平坦化したときに、かかるポリシリコン層に発生する内部応力を緩和させることができるマイクロマシンの製造方法を提供すること。 - 特許庁