「STRESS」を含む例文一覧(22493)

<前へ 1 2 .... 356 357 358 359 360 361 362 363 364 .... 449 450 次へ>
  • To provide a shaft for a torque sensor capable of increasing the output of the sensor with an adverse effect of thermal stress reduced even if the length of a magnetostrictive member is reduced in the event that the shaft for the torque sensor is made by joining support parts of another kind of metal to the bulk magnetostrictive member put between them.
    トルクセンサ用シャフトをバルクの磁歪材を挟むように他の支持金属を接合して構成した場合に、磁歪材の長さを短くしても熱応力による悪影響を少なくでき、センサの出力を高くすることを可能にする。 - 特許庁
  • To dissolve deterioration in the airtightness caused by the void at the junction between a frame and an insulating terminal member, the shortage of brazing material, or the like, and the marring of the junction reliability by the residual thermal stress among the substrate, the frame, and the terminal member.
    枠体と絶縁端子部材との接合部のボイドやロウ材不足等による気密性の劣化と、ロウ材溜まりによる基体と枠体と端子部材との間の残留熱応力で接合信頼性が損なわれていたのを解消すること。 - 特許庁
  • To provide a metal shaft expanding apparatus which can elucidate the effect of the change of the relative bending supporting point to both holding portions on the local expansion of a work by applying the rotation, the compressive stress and the bending.
    ワークに回転と圧縮圧力と曲げを作用させて局部的に拡径成形する拡径加工において、両保持部に対する相対的な曲げ支点位置を変化させ、それが成形に及ぼす影響を解明することを可能とする成形装置を提供する。 - 特許庁
  • The sheet-shaped piezoelectric element 22 performs an electric generation activity in accordance with the change in outside stresses to the lure fish body 11 based on the stress of waves and tension changes in a main fishing line, and the light-emitting diode 21 emits the light in accordance with the movement of the lure in a non-artificial pattern.
    シート状圧電素子22は、波の強弱や道糸の張力変化に基づくルアー魚体11に対する外部応力の変化に伴って発電作用をし、発光ダイオード21は、ルアーの動きに応じて非人為的なパターンで発光する。 - 特許庁
  • As a result, at the end that is not fixed, the force equal to or exceeding the disconnection stress is not applied to the crossover 60, when the protective tubes 611, 612, and 613 and the crossover line 60 thermally expand and shrink, respectively, and the crossover 60 is prevented from being disconnected.
    その結果、該固定されていない端は、保護チューブ611、612、613と渡り線60がそれぞれ熱膨張及び収縮した時に、渡り線60に断線応力以上の力が加わらず、渡り線60の断線が保護される。 - 特許庁
  • When a ratio (R2/R1) of a curvature radius R2 of the band for a curvature radius R1 of the crowning surface is changed and maximum tensile stress σmax of a band outer peripheral surface is measured, a relation between both of R1 and R2 exists as shown in a Figure.
    クラウニング面の曲率半径R_1 に対するバンドの曲率半径R_2 の比(R_2 /R_1 )を変化させてバンド外周表面の最大引っ張り応力σ_ma_x を計測したところ、両者間には図示のような関係が存在することを確かめた。 - 特許庁
  • To provide a method for holding a thin plate and a floating holding mechanism wherein the thin plate can be set on the holding mechanism from the upright direction and prevented from collision with a receiving surface of the holding mechanism without generating a bending stress and hindering restoration by a corrective force.
    薄板に曲げ応力をかけることなく、矯正力による復元を妨げることなく、把持機構に薄板を真上からセッティングでき、把持機構の受面に薄板を衝突させない薄板把持方法及びフローティング把持機構を提供する。 - 特許庁
  • To provide a stacked inductor that reduces the influence of stress given from a nonmagnetic body as a magnetic gap, and improves DC superposition characteristics, while suppressing deterioration of a magnetic property of a magnetic body, and a stacked substrate incorporating the stacked inductor.
    磁気ギャップとなる非磁性体から受ける応力の影響を低減できて、磁性体の磁気特性の劣化を抑制しながら直流重畳特性の向上を図れる積層インダクタ、及び該積層インダクタを内蔵する積層基板を提供する。 - 特許庁
  • Hereby, the action of the control circuit (7) stops, and the repetition of the on-off action of the control circuit (7) becomes possible, so that the converter can protect an FET (5) and a main rectification smoothing circuit (6) from an overcurrent, and can prevent the breakage of the element by relaxing electrical stress.
    これにより、制御回路(7)の動作が停止し、制御回路(7)のオン・オフ動作の繰り返しが可能となるので、FET(5)及び主整流平滑回路(6)を過電流から保護し、電気的ストレスを軽減して素子の破壊を防止できる。 - 特許庁
  • To prevent stress which may give bad influence on a second recording medium from being imposed in an image forming process on a first record medium of a composite recording medium, where the second recording medium is provided at one part of the region of the first recording medium.
    第1記録媒体の一部の領域に第2記録媒体を設ける複合記録媒体の第1記録媒体に対する画像形成処理の過程で、第2記録媒体に悪影響を及ぼすようなストレスが加わるのを防止する。 - 特許庁
  • To provide an impeller of high reliability with any unwelded portion eliminated capable of effectively relieving a stress concentration simply at a low cost, compared with a conventional method including a projection on a rounded part, fillet welding and formation of rounded part by finishing with a grinder.
    応力集中を緩和する有効な手段であり、R部の突起、すみ肉溶接とグラインダ仕上げによるR部形成と比較して簡易に低コストで応力集中を緩和でき、未溶着部を無くし、高信頼性の羽根車を提供する。 - 特許庁
  • The connecting means 21, 22 can elastically expanded in the cross direction of the diaper 1, the connecting means 22 positioned in the lower part of the connected side edge part 13 has higher extensible stress than the connecting means 21 positioned in the upper part thereof.
    連結手段21,22は、おむつ1の幅方向へ弾性的に伸長可能なもので、連結した側縁部13の下方部分に位置する連結手段22は、上方部分に位置する連結手段21よりも高い伸長応力を有する。 - 特許庁
  • Since the fitting property to a groove 262 formed on a supporting plate 170 is thereby improved, the projection hardly comes off from the groove even if tensile stress is applied to it and a malfunction caused by the contact of the supporting plate with a holding ring 110 due to a mounting failure can be avoided.
    上記構成によって、支持プレート170に形成される溝262との嵌合性が向上するので、引張応力を受けても溝から外れにくくなり、装着不良により保持リング110に接触して生じる動作不良を回避できる。 - 特許庁
  • The spheroidal graphite cast iron can exhibit excellent mechanical properties satisfying a fatigue strength of ≥300 MPa, a tensile strength of ≥700 MPa, a proof stress of ≥400 MPa and an elongation of ≥7% and satisfactory machinability as-cast.
    この球状黒鉛鋳鉄は、鋳放しで、疲労強度300MPa以上、引張強さ700MPa以上、耐力400MPa以上、伸び7%以上の優れた機械的性質と、良好な被削性とを発揮することが可能である。 - 特許庁
  • The fitting member 20 has a main body part fitted to a first member, fitting parts 25 fitted to a second member 30 and stress absorbing parts 26 connecting the main body part to the fitting parts 25 and formed to be easily deformed.
    取付部材20は、第1の部材に取り付けられる本体部と、第2の部材30に取り付けられる取付部25と、前記本体部と前記取付部25とを連結し且つ変形しやすく形成された応力吸収部26と、を有する。 - 特許庁
  • A bolt 5 is inserted to an arch rib 2 in the vicinity of the supporting point of a wooden arch bridge, where a complicate synthetic stress is generated, in the direction orthogonal to a laminated lamina, and bearing plates 6 and 6 installed at both ends of the bolt are pushed by nuts 7 and a prestress is introduced.
    複雑な合成応力が発生する木製アーチ橋の支点近傍におけるアーチリブ2には、積層するラミナと直交する方向にボルト5を挿通し、その両端に設ける支圧板6,6をナット7により押圧してプレストレスを導入する。 - 特許庁
  • The right and left side parts 36, 36 of the claw piece 34 are each easily elastically deformable by the cutout part 35, and upon an impact load being applied to the claw piece 34, the impact is alleviated and stress acting on the base end of the claw piece 34 is reduced.
    この切欠部35により爪片34の左右側部36,36がそれぞれ弾性変形容易となり、爪片34に衝撃荷重が加わった際に、衝撃が緩衝されて爪片34の基端部に作用する応力が低減する。 - 特許庁
  • At this time, the ruptured surface 19 is formed by breaking a crest part 17 by applying stress on the crest part 17 on the screw shape part remaining on the cylinder bore inner surface 5 on the rear side in the delivering direction of the cutting tool 7 by the protruded part 7c provided on a cutting blade 7a.
    この際、切削工具7の送り方向後方側のシリンダボア内面5に残るねじ状部分の山部17に対し、切刃7aに設けた凸部7cによって応力を作用させ、山部17を破断して破断面19を形成する。 - 特許庁
  • As a result, the nozzle plate can increase the atomizing area, atomizing quantity and liquid-gas exchange rate to prevent excessive stress on vibrating from concentrating at the center of the nozzle plate or from cracking or breaking the nozzle plate.
    これによって、本発明の噴出孔片は霧化領域、霧化量及び液体—気体の交換効率を増大することができ、しかも振動時の応力が噴出孔片の中心に集中しすぎるため、亀裂・破損が生じるのを避けることができる。 - 特許庁
  • To provide a method for cooling a die by which, during the operation of a die, the occurrence of rust as the starting point of cracks to water-cooled holes in which stress caused by thermal fatigue is generated is suppressed, thereby the life of the die can be improved.
    金型の操業中において、熱疲労による応力が発生する水冷孔への亀裂の起点となる錆の発生を抑え、これにより金型の寿命を向上させることができる金型の冷却方法を提供すること。 - 特許庁
  • Since the lower the blade height is, the smaller are the protruding angles of the protrusions 15c-17c; the higher protrusion has less stress concentrated on the protruding section and is hard to break.
    しかし、突き出し部15c〜17cは、羽根面からの突き出し角度が、突き出し高さの低い方から順に小さく形成されているので、突き出し高さの高い突き出し部ほど突き出し位置に掛かる応力の集中が緩和され、破壊されにくくなっている。 - 特許庁
  • To realize ground compaction free from irregularities over the whole length of an outer pipe with reduction of the device cost and work man-hour, and to prevent the stress concentration in the outer pipe to eliminate the possibility of collapse of a tunnel.
    装置コストおよび作業工数を、従来技術に比して大きく低減させて、外管の全長にわたるむらのない地山固結等を実現し、併せて、外管内での応力集中を防止して、トンネルの崩壊等のおそれを取り除く。 - 特許庁
  • To provide a method for manufacturing a liquid crystal display device, with which the liquid crystal display device is mounted on the casing of a portable device with high precision and strength of the liquid crystal display device against external stress is improved, and to provide the liquid crystal display device.
    携帯機器の筐体に液晶表示装置を高精度で組み付けると共に、外部応力に対する液晶表示装置の強度を向上させた液晶表示装置の製造方法及び液晶表示装置を提供する。 - 特許庁
  • To provide a stator coil in which damages to an insulating layer, due to mechanical stress caused at the start and stoppage of a rotary electric machine are suppressed, and the rotary electric machine can be reduced in size, reduced in cost and enhanced in the capacity through the increase of the current density in an element conductor.
    回転電機の起動、停止時の機械的ストレスによる絶縁層の破壊が抑制され、素線導体における電流密度の増加により回転電機の小型化、低コスト化、および大容量化が可能な固定子コイルを提供すること。 - 特許庁
  • Hereby, a crimp-style terminal 14 can be connected and since it is substantially in parallel with the power wiring joint 7 of the terminal board 7, excessive stress caused by sharp bending will not occur, and even if it is subjected to vibration or the like, there is no risk of wire breaking.
    これにより、圧着端子14が端子板7の電源配線接続部7aにほぼ沿うように接続することができるので、急激な屈曲による過大な応力が生じず、振動などを受けても断線する危険がない。 - 特許庁
  • On the outer peripheral surface of the metal member 2 on which the resin section 1 is attached, a concave/convex surface including concave and convex portions is formed, and on at least one of the concave and convex portions of the concave/convex surface, an R surface to relax the stress concentration is formed.
    前記樹脂部1が固着される金属部材2の外周面に、凹部と凸部とからなる凹凸面が形成され、この凹凸面の凹部と凸部のうち少なくとも一方に応力集中を緩和するR面が形成されている。 - 特許庁
  • Further, whether the impact to the head causes brain damage is determined (S23, S25) based on whether a first condition on the analysis value of strain is established (S24) and whether a second condition on the analysis value of hydrostatic stress is established (S22).
    さらに、ひずみの解析値に関する第1条件の成否(S24)と、静水圧応力の解析値に関する第2条件の成否(S22)とに基づき、頭部への衝撃によって脳損傷が発生するか否かを判定する(S23およびS25)。 - 特許庁
  • The stirring is improved by circulating a cooling water through a large stirring blade to enhance a heat removing performance, controlling a shearing stress under the condition of turbulent flow stirring and dividing a large plate-shaped blade to a longitudinal direction in order to have an angle each other.
    大型攪拌翼に冷却水を流通して除熱性能を向上させ、乱流攪拌条件にてせん断応力を制限した攪拌を行ない、また大型板状翼を高さ方向に分割して角度を持たせることで混合を良くする。 - 特許庁
  • The arrangement concentration of dummy active regions 11 in a p-type well 3 is relatively low, making a stress to be applied on a p-type active region 5 relatively small and hence preventing a decline in driving current of the n-channel type MOS transistor.
    Pウエル3側におけるダミー活性領域11の配置密度は比較的低くなっており、P型の活性領域5に及ぶ応力は比較的小さく、Nチャネル型MOSトランジスタの駆動電流の減少を低減させることができる。 - 特許庁
  • The bulk textured yarn is produced by the knit-deknit processing of a false-twist crimped yarn having a crimp recovery (CR) of ≤20%, a crimp developing elongation (TR) of ≤10% and maximum value of the shrinking stress of ≥0.1 CN/dtex and ≤1.0 CN/dtex.
    伸縮復元率(CR)が20%以下、捲縮発現伸長率(TR)が10%以下で、収縮応力のMAX値が0.1CN/dtex以上1.0CN/dtex以下の仮ヨリ捲縮糸がニットデニット加工されてなることを特徴とする嵩高加工糸。 - 特許庁
  • Further, the part to be held can be made large-sized, thereby, a position apart from the optical surface can be held, therefore, the transmission of a stress due to the holding to the effective area of the optical member can be suppressed and the optical member can be kept at a high performance.
    また、被保持部を大型化できることで、光学面から離れた位置を保持することができるので、保持による応力が光学部材の有効領域へ伝達するのを抑制することができ、光学部材を高性能に維持することができる。 - 特許庁
  • The high-strength steel sheet has alloy components satisfying equation: Ceq (C equivalent)=C+Mn/20+Si/40+4P+2S<0.4 and has a slope dσ/dεof ≥5,000 MPa in a stress-strain diagram in the range where true strain obtained in a tensile test is 3-7%.
    合金成分が、 Ceq(C当量)=C+Mn/20+Si/40+4P+2S<0.4を満たし、かつ、引張り試験で求められた真歪み3〜7%の間における応力歪み線図の傾きdσ/dεが5000MPa以上である高強度鋼板とする。 - 特許庁
  • The high-strength steel sheet has alloy components satisfying equation: Ceq (C equivalent)=C+Mn/20+Si/40+4P+2S≥0.4 and has a slope dσ/dεof ≥5,000 MPa in a stress-strain diagram in the range where true strain obtained in a tensile test is 3-7%.
    合金成分が、 Ceq(C当量)=C+Mn/20+Si/40+4P+2S≧0.4を満たし、かつ、引張り試験で求められた真歪み3〜7%の間における応力歪み線図の傾きdσ/dεが5000MPa以上である高強度鋼板とする。 - 特許庁
  • Both ends 2a of a shape steel 2 are restricted by a clamp 10, and the tensile force is applied in the longitudinal direction of the shape steel 2 by a cylinder power unit 5, and the yield stress is applied in the entire section orthogonal to the longitudinal direction of the shape steel 2.
    両端2aをクランプ10によって拘束され、シリンダー動力部5によって形鋼2の長手方向に引っ張り力が加えられ、形鋼2の長手方向に対する垂直な断面の全体に降伏応力が加えられる。 - 特許庁
  • To prevent the generation of cracks in an interlayer insulating film even if tensile stress is generated by a barrier metal, and to prevent the occurrence of peeling between the interlayer insulating film and a film which is formed on the interlayer insulating film.
    バリアメタルによって引っ張り応力が発生することがあっても、層間絶縁膜にクラックが発生することを防止すると共に、層間絶縁膜と該層間絶縁膜の上に接して形成された膜との界面に剥離が発生することを防止する。 - 特許庁
  • This cutting causes cracks 8 on the substrate 1 due to a thermal stress by radiating CO2 laser beams 5-2 onto a reverse face of the ceramic substrate 1, and it is cut by progressing the cracks 8.
    少なくとも一方向に所望速度で移動するワークテーブル3上に光導波回路が形成された表面側を固定してセラミックス基板1の裏面を加工するので、高寸法精度で再現性よく切断加工を行うことができる。 - 特許庁
  • (1) The 100% elongation stress of the film is 40-300 MPa at 25°C and 1-100 MPa at 100°C in both longitudinal and lateral directions; (2) the melting point is 200-245°C; and (3) the in-plane orientation degree is ≥0.01 and <0.11.
    (1)フィルムの長手方向及び幅方向における100%伸張時応力が、いずれも25℃において40〜300MPa及び100℃において1〜100MPa(2)融点が200〜245℃である(3)面配向度が0.01以上0.11未満 - 特許庁
  • The method for simulating the injection molding process comprises the steps of calculating a dimensional change amount of the molding based on thermal strain data due to a contraction of a cooling step and strain data in association with an internal stress change, and calculating relative position data of a mold and the molding generated in association with the dimensional change amount (S6).
    冷却過程の収縮による熱歪みデータおよび内部応力変化に伴う歪みデータに基づき、成形品の寸法変化量を算出し、それに伴って発生する型と成形品の相対位置データを算出する(S6)。 - 特許庁
  • The steel material for reinforcement has a metal microstructure containing 80% or more of bainite in volume ratio and such mechanical characteristics as an yield stress of 785 MPa or higher, a total elongation of 8% or more, a drawing property of 30% or more, and also, a Charpy impact value uE_o at 0°C of 80 J/cm^2 or higher.
    体積比率で80%以上のベイナイトを含む金属組織を有し、降伏応力:785MPa以上、全伸び:8%以上、絞り:30%以上および0℃におけるシャルピー衝撃値uE_0:80J/cm^2以上の機械的特性を有するものとする。 - 特許庁
  • As a result, the damage of the hose by the stress concentration by the compression amount La can be prevented, the removing force of the hose can be secured by the compression amount Lb, and the pressure loss increase can be avoided since it is not necessary to provide a projection part in the inner surface of a nipple 10.
    圧縮量Laにより応力集中によるホースの損傷を防止でき、圧縮量Lbによりホースの抜け力を確保でき、ニップル10の内面には突出部を必要としないので圧力損失増加を回避できる。 - 特許庁
  • To provide a barrier film having been finished to be tight and beautiful due to an appropriate heat shrinking stress though it is a highly heat shrinkable, has the heat sealability superior in air tightness, further superior in the barrier property, the resistance to pinholing, the resistance to whitening by alcohol and also the anti-clouding property.
    高熱収縮性でありながら適度な熱収縮応力でタイトに美麗に仕上がりつつ、機密性に優れたヒートシール性で、バリア性、耐ピンホール性にも優れ、更に耐アルコール白化性、防曇性にも優れているバリアフィルムを提供する。 - 特許庁
  • To provide a highly reliable resin-sealed type electronic device which is strong against bending stress, and is hardly deformed by enhancing the durability (long service life) of the soldering part of a semiconductor power element for an internal combustion engine and moreover improving the rigidity of the device as a whole.
    内燃機関用の半導体パワー素子のはんだ付け部の耐久性(長寿命)を高め、しかも装置全体の剛性も高めて曲げ応力に強く変形しにくい信頼性の高い樹脂封止形電子装置を提供する。 - 特許庁
  • To provide a faucet mounting structure capable of being surely fixed on the mounting surface without being influenced by stress or the like resulting from handle operation of a water hammer or a faucet body even after mounting the faucet body mounted and fixed on the mounting surface by screwing a clamping screw thereon.
    締付具をねじ込むことにより取付面に取付固定された給水栓本体が、取付後にも、ウォーターハンマや給水栓本体のハンドル操作による応力などの影響を受けず確実に取付面に固定されるようにすること。 - 特許庁
  • Thereby, the substrate for a recording head which has been improved in the thermal conductivity, a residual stress profile and structural stability is provided, and the ink-jet recording head which can maintain the high frequency discharge movement in the stable state for a long period is obtained.
    これにより、熱伝導性、残留応力特性、構造安定性等が改善された記録ヘッド用の基体が提供され、高周波な吐出動作を安定した状態で長期間持続することが可能なインクジェット記録ヘッドが実現される。 - 特許庁
  • The preservation system of the vehicle traffic structure comprises a measuring instrument 3 that is arranged at the structure part of a structure body where a vehicle passes for measuring actual traffic condition data D1; and a calculator 1 for calculating the stress of the structure part corresponding to the actual traffic condition data D1.
    車輌が通過する構造物体の構造部位に配置され交通実態データ(D1)を計測する計測器(3)と、交通実態データ(D1)に対応して構造部位の応力を計算する計算器(1)とから構成されている。 - 特許庁
  • The operation means 11 is provided for calculating an equivalent number of repetitions by performing an infinite time integration of the envelope curve of the axial torque value based on the envelope curve, and a relation between stress and the number of repetitions in a material life to predict life of the rotary machine.
    前記包絡線と、応力と材質の寿命回数の関係に基づいて、軸トルク振幅値の包絡線を無限時間積分して等価な繰返し回数を演算し、回転機械の寿命を予測する演算手段11を備えている。 - 特許庁
  • To provide a ball joint having high rigidity at a low cost, absorbing the size tolerance of components, maintaining the excellent load resistance against a load and durability, reducing the damage by the stress at the time of assembling, and improving an yield.
    高剛性かつ低コストで、各構成部品の寸法公差を吸収し、負荷に対する優れた耐荷重性および耐久性を維持しつつ、組み付け時の応力などによる損傷を低減し、歩留まりが向上するボールジョイントを提供する。 - 特許庁
  • To provide a flexible tube capable of reducing stress acting on both end parts of the flexible tube in mutual shearing displacement of connection pipe bodies.
    中央にベローズ部32を有するフレキシブルチューブ3の両端部を両排気管(接続管体)1、2の管端部に取り付けて接続するフレキシブルチューブ3であって、ベローズ部32の両端部A1、A3の山谷ピッチが中央部A2の山谷ピッチより小さく形成されている。 - 特許庁
  • To provide a conductive rubber roller suitable, in particular, as a development roller that makes electric resistance uniform, is excellent in electrostatic charge properties relative to deposits, for example, toner, and capable of sustaining the electrostatic charge properties and reducing stress on such deposits.
    電気抵抗を均一化できると共にトナー等の付着物への帯電性に優れ、かつその帯電性を持続可能であり、さらにトナーなどの付着物に与えるストレスを軽減できる、現像ローラに特に好適な導電性ゴムローラを得る。 - 特許庁
  • In the high strength thin steel sheet provided with simple state surface formation having 0.3-1.5 μm Ra, this steel sheet is provided with a range having ≥100 MPa the absolute value of a compressed residual stress on the surface layer part in the range of 2-10% sheet thickness.
    Raで0.3〜1.5μmであるディンプル状の表面形態を備えた高強度薄鋼板であって、圧縮残留応力の絶対値が100MPa以上となる領域を、板厚の2〜10%の範囲の表層部に有することを特徴とする高強度薄鋼板。 - 特許庁
<前へ 1 2 .... 356 357 358 359 360 361 362 363 364 .... 449 450 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.