In the expression, t is a radial thickness of the wire; w is the axial width of the wire; I is a current amount through the coil; B is flux density applied to the wire in the innermost periphery of the coil; and the stress (σ) is B×I×r_max/(w×t). r_max<σ_wire×w×t/(B×I) (前記式中、t:線材の径方向の厚さ、w:線材の軸線方向の幅、I:コイルの電流量、B:コイル最内周の線材に印加される磁束密度、応力(σ):B×I×r_max/(w×t) - 特許庁
Since the winding termination 9 of the coil is not clamped between the diaphragm and a joining face of the case B, the outer circumference of the diaphragm is uniformly adhered to the case B on the entire circumference and no stress is exerted to the winding termination even when the outer circumference of the diaphragm is pressed at joining. コイルの巻き線端末9が振動板とケースBの接合面に挟まれないから、振動板の外周が全周で均一にケースBに接着され、接合時に振動板の外周を加圧しても巻き線端末がストレスを受けたりしない。 - 特許庁
The printed resin film to be laminated on the embossed decorative metallic sheet has a polyester resin layer (A), a printed layer and a transparent protecting layer laminated in that order, and an expansion stress relaxation agent finely dispersed in the polyester resin layer (A) and further, the embossed surface of the transparent protecting layer. ポリエステル樹脂層及び印刷層及び透明保護層がこの順で積層され、ポリエステル樹脂層(A) 中に伸縮応力緩和剤が微分散され、かつ透明保護層の表面がエンボス加工されている、エンボス化粧金属板積層用印刷樹脂フィルム。 - 特許庁
Even if the main stress acts on the circumference of the boom boss 14 by the operation of the arm in excavating work, the bonding strength between the web 12A and the reinforcing plate 18 can be enhanced by the fillet weld part 19 and each deep penetration weld part 20. これにより、掘削作業時にアーム11が作動してブーム用ボス部14の周囲に主応力が作用したとしても、すみ肉溶接部19と各深溶け込み溶接部20とによってウェブ12Aと補強板18との接合強度を高めることができる。 - 特許庁
Then, the stress caused by a difference in coefficient of thermal expansion between the printed board 1 and the LSI chip can be dispersed (relaxed) by the pump pad 11 and the solder ball 13, so the high reliability of the junction part can be ensured in the LSI chip mounting. 従って、プリント基板1とLSIチップとの熱膨張率差によって生じ得る応力をバンプ型パッド11及び半田ボール13により分散(緩和)することにより、LSIチップ実装の接合部における高信頼性を確保することができる。 - 特許庁
In this sintered compact, strain caused by crystal defects introduced into the cBN crystals on conversion sintering, and stress introduced into the sintered compact on its discharge from an ultrahigh pressure-high temperature state are reduced, and high strength suitable for a cutting tool is imparted thereto. この焼結体は、変換焼結の際にcBN結晶内に導入される結晶欠陥による歪みや、超高圧高温状態から取り出す際に焼結体内に導入される応力が低減され、切削工具に好適な高強度を具えている。 - 特許庁
To provide a manufacturing method of a grid for a battery capable of reducing corrosion of the grid by sharpening an angle of a blade-edge slanted surface contacting with a backside of the upper blade as it is headed to an upper part, and by eliminating unnatural stress by surely cutting a crosspiece up to a knot part. 上刃の刃裏面に接する刃先傾斜面の角度を上部ほど鋭くし、桟を結節部まで確実に切断して無理な応力を加えないようにすることにより、格子の腐食を少なくすることができる電池用格子の製造方法を提供する。 - 特許庁
To provide an image forming apparatus mounted with a cleaning device in which a sufficient napping effect is always obtained over a long time by preventing stress from being applied to the tip portions of the bristles of a cleaning brush roller, in an irregular state, even while the cleaning brush roller is stopped to stand by. クリーニングブラシローラが待機停止中であっても、クリーニングブラシローラの毛先部へのストレスが不規則な状態に係るのを防止し、常に、十分な起毛効果が長時間に亘って得られるようにしたクリーニング装置を装着した画像形成装置を提供する。 - 特許庁
To solve the problem of the conventional connecting structure of a skeleton and an aseismic reinforcement, wherein in stress transmission between the skeleton and the aseismic reinforcement, load of an anchor as a fixing member is increased, so that the number of anchors should be increased in order to heighten the strength of a connecting part. 従来の躯体と耐震補強材との接合構造では、躯体と耐震補強材との間の応力伝達において固定部材としてのアンカーの負担が大きくなり、接合部の強度を大きくするためにはアンカーの数を多くしなければならない。 - 特許庁
A detecting optical fiber 29 having a strength characteristic comparable to that of an optical fiber for YAG laser is for example laid next to the YAG optical fiber 5, so that it is arranged in a place for receiving a stress to the identical degree as to disconnect the YAG optical fiber 5. YAGレーザ用の光ファイバ5と同等の強度的特性を有する検出用光ファイバ29をYAGレーザ用の光ファイバ5に添わせるなどして、YAGレーザ用の光ファイバ5を断線せしめるストレスと同等のストレスがかかる場所に配置する。 - 特許庁
To provide a highly durable and low cost blade supporting structure for a motor grader, which keeps not only a face pressure between a rail guide and a guide bracket but also a bending stress of a rail guide due to an excavating strength away from increasing, while keeping a common nature in a guide bracket type. ガイドブラケットの型の共通性を保持しつつ、掘削力によるレールガイドとガイドブラケットとの間の面圧の増大及びレールガイドの曲げ応力の増大を防止して、高い耐久性を具えかつ低コストのモータグレーダのブレード支持構造を提供する。 - 特許庁
Since a rotating shaft 162 is provided in the approximately central position (barycenter) of a cross section of a slat 15, an operating physical force in the rotation of the slat 15 is decreased, and stress acting on an end member, an attachment 17, an interlocking member 18, an operating portion, etc. can be reduced. スラット15の断面略中心(重心)位置に回動軸162が設けられているので、スラット15を回動させる際の操作力が小さくなるとともに、端部部材やアタッチメント17、連動部材18、操作部などに作用する応力が小さくできる。 - 特許庁
To provide a discharge lamp lighting apparatus that can suppress heating of filament by reducing power loss according to current flowing to filament in protection operation after detecting an ending of life of lamp, and suppress stress to switch elements of an inverter circuit in no loading state when lamp is replaced. ランプ寿命末期検出後の保護動作時にランプフィラメントに流れる電流による電力損失を低減してフィラメント部の発熱も抑制すると共に、ランプ交換時の無負荷状態においてもインバータ回路のスイッチング素子に与えるストレスを抑制する。 - 特許庁
To provide a bearing means which is hard to be deformed, not held at a half-way position, hardly increase thrust stress of a rotor and hardly receive deformation to its shaft hole, in a shutoff valve used for a microcomputer meter, etc., with a motor as a power source. 本発明はマイコンメータなどに使用されるモータを動力源とした遮断弁に関するものであり、変形しにくく、中途半端な位置で保持されず、ロータのスラストストレスを増大せず、軸穴に変形のおよびにくい軸受手段を提供するものである。 - 特許庁
In the laminated water-resistant pepr wherein at least one layer comprising a thermoplastic resin is laminated on each of both surfaces of the paper base material, the heat shrinkage stress of the resin layer laminated on a printing surface side of the paper base material is made lower than that of the resin layer laminated on the back thereof. 紙基材の両面に1以上の熱可塑性樹脂からなる層が積層された積層耐水紙において、印字面側に積層された樹脂層の熱収縮応力が裏面に積層された樹脂層の熱収縮応力より小さくする。 - 特許庁
To obtain an electrostatic stress optical modulator which is capable of the same high speed, high precise display operation as by active matrix drive using TFT, by means of a simple inexpensive structure like a simple matrix, and also to obtain its drive method and a flat-panel display device using the modulator. 単純マトリクスのような簡単な安価な構成で、TFTを用いたアクティブマトリクス駆動と同様の高速、高精細な表示動作が可能な静電気応力型の光変調素子と、その駆動方法並びに平面表示装置を提供する。 - 特許庁
The automatic lid opening/closing device for a composting container has a shape memory alloy 11 fastened to the lid of the container and takes advantage of the alloy's property of starting transformation in a range of set temperatures, and stress generated at the time of transformation is used as a reaction force for lid opening/closing without requiring any electrical power. 蓋へ締結した形状記憶合金11が設定温度域で変態を開始する特性を用いて、その変態時の発生応力を蓋開閉用反力として用いることで成る電気動力を不要とした堆肥化容器自動蓋開閉装置。 - 特許庁
To provide a method for producing a connecting rod with which higher proof stress can be obtained by further optimizing the forming state of V-base precipitation while using a non-heat treated steel for hot forging, containing V and further, effectively making good use of the added V. Vを含有する熱間鍛造用非調質鋼を用いつつ、V系析出物の形成状態をより最適化し、ひいては添加したVを有効活用することにより、さらに高耐力化を図ることができるコンロッドの製造方法を提供する。 - 特許庁
The center mounting part (60) has an insertable mounting tab (66) into a mounting slot (34) of the dielectric housing (12), and the front side latch part (62) is able to link to a latch of the other connector, and the rear side stress releasing device (64) is able to be engaged with an electric cable. 中央取付部(60)は、誘電性ハウジング(12)の取付スロット(34)内に挿入可能な取付タブ(66)を有し、前側ラッチ部(62)は、相手方コネクタとのラッチ係合が可能であり、後側歪み解放部(64)は電気ケーブルに係合可能となっている。 - 特許庁
It is devised that the fatigue strength of a thin wall part at the portion of a grinding clearance groove 4 formed at both the end parts in the axial direction of the raceway surface 2, is enhanced so as to allow the durability of each flange to be enhanced by letting residual compression stress be incurred in the portion of the grinding clearance groove 4. 軌道面2の軸方向両端部に形成された研削逃げ溝4の部分に圧縮残留応力を形成して、逃げ溝4の部分における薄肉厚部の疲労強度の向上を図り、鍔3の耐久性の向上を図る。 - 特許庁
To provide a bearing device for a vehicle wheel embodied in a third generation structure in which the inner ring is fitted by pressure fast to a minor diameter stepped part of a hub ring, capable of enhancing the durability of the hub ring by suppressing a stress generated at the inside corner formed from the hub ring shoulder and the minor diameter stepped part. ハブ輪の小径段部に内輪が圧入固定される第3世代構造において、ハブ輪の肩部と小径段部との隅部に発生する応力を抑制し、ハブ輪の耐久性を向上させた車輪用軸受装置を提供する。 - 特許庁
To provide a polyethylene-based polymer composition which is excellent in molding processability and strength, rigidity, physical properties such as ESCR (environmental stress cracking resistance), and the like as compared with those of a conventional polyethylene-based polymer composition, whose molded body has a good shape also, and which is especially suitable for a large-sized hollow molding application, and the like. 従来のポリエチレン系重合体組成物に較べ、成型加工性および強度、剛性、ESCR等の物性に優れ、成型体の外観も良好な、特に大型中空成型用途等に適したポリエチレン系重合体組成物を提供する。 - 特許庁
To provide a chip component with excellent productivity without unnecessarily causing air gap under itself after mount and without causing cracks in the middle of itself due to stress caused at built-in, and to provide a component built-in module employing the chip component and a manufacturing method of them. 生産性がよく、実装後にチップ部品下部に不必要に空隙が生じないチップ部品で、内蔵時のストレスによって、チップ部品中央部に亀裂を生じることのないチップ部品、それを用いた部品内蔵モジュール及びそれらの製造方法を提供する。 - 特許庁
To provide an audio plug capable of preventing breakage, damage and function degradation of the plug and a connection part between a cable and the plug by preventing unreasonable stress from being imposed on the plug by allowing a plug body to be separated from a plug-in part having a channel plug. プラグ本体をチャンネルプラグを備えた差込み部から離脱可能にすることによってプラグに無理な応力がかかるのを回避して、プラグやケーブルとプラグとの接続部の破損や損傷、機能低減を回避することができるオーディオプラグを提供する。 - 特許庁
To improve read and write quality by suppressing interference stress caused by deformation, twisting, or bending, or the like of a tray applied to a module base through a bracket, in an optical pickup module and an optical disk device provided therewith. 本発明の光ピックアップモジュール及びそれを備えた光ディスク装置は、トレイのゆがみ、ねじれ、または曲りなどによりブラケットを介してモジュールベースにそれらの干渉応力が作用するのを抑制し、読み書き品質の向上を実現することを目的とする。 - 特許庁
Since a first to a third press-fit members 111, 112, 113 are provided at a base portion 11 to be supported firmly to a housing 2, only the compression stress is acted on a pair of lead parts 11c, 11d, thereby separation of solder from the printed-circuit board 1p can be made difficult. 基部11に第1から第3圧入片111・112・113を設けて、ハウジング2に強固に保持する構成としたので、一対のリード部11c・11dには、圧縮応力のみが作用し、プリント基板1pとのはんだ剥離を困難にできる。 - 特許庁
When the clear monochrome mode is selected, the image formation is carried out while keeping the interval between papers same as that during a normal image formation, and a fixing temperature recovery time (resting time) is secured in mass, then, the drive of the developing device can be stopped, so that stress on the developer can be reduced. クリア単色モード選択時に、通常画像形成と同じ紙間を維持して画像形成し、定着温度回復時間(休止時間)をまとめて確保することによって、現像装置の駆動を停止することが出来るため、現像剤へのストレスを低減できる。 - 特許庁
To provide an oxygen concentration detecting element capable of preventing the occurrence of a crack or the like caused by the heat stress in a heat part or a detection part, enhancing the yield of the lead part wires of a pair of electrodes and reduced in cost by reducing the number of times of printing of a heater insulating layer. ヒータ部や検出部に熱応力に起因するクラック等の発生を防止できると共に、一対の電極のリード部線の歩留まりが向上し、且つ、ヒータ絶縁層の印刷回数を削減して低コストにできる酸素濃度検出素子を提供する。 - 特許庁
To provide a highly durable coin-shaped RFID tag in which the molded joint face of a disk-shaped edged resin case and a cover-shaped part are hardly peeled from each other even when an expansion/contraction stress is repeatedly applied due to a change in environment over time, especially a cyclic change in temperature. 経時的な環境変化、特に温度の周期的変化により、膨張・収縮応力が繰り返し加わっても円盤状の縁付き樹脂ケースと蓋状部の成型接合面が剥離しない耐久性の高いコイン型RFIDタグを提供すること。 - 特許庁
At the time of overcurrent, short-circuit of a load, or starting, currents that flow at sides of the primary windings (2a) and secondary windings (2b) of a transformer (2) are limited more strongly so that the electrical stress applied to each component of the primary and secondary sides of the switching power supply can be reduced. 過負荷時、負荷短絡時又は起動時にトランス(2)の1次巻線(2a)側及び2次巻線(2b)側に流れる電流がより強く制限されるので、スイッチング電源装置の1次側及び2次側の各部品に加わる電気的なストレスを軽減できる。 - 特許庁
To provide a normal temperature shrinkable tube for a cable connecting part which is excellent in damage tolerance, in which a fracture hardly occurs in an extended state of an enlarged diameter, and which is also excellent in permanent elongation characteristic and stress relaxation characteristic, and a cable connecting part using the normal temperature shrinkable tube. 耐外傷性が良好で、拡径伸長状態での破断が生じにくい上に、永久伸び特性・応力緩和特性にも優れるケーブル接続部用常温収縮チューブ、及びそのような常温収縮チューブを備えたケーブル接続部を提供する。 - 特許庁
An energy beam is made to be incident on an evaluation region of the sample, a phase distribution image in the evaluation region of the energy beam having transmitted through the sample is acquired, and the acquired phase distribution image is analyzed, thereby the stress distribution in the evaluation region is measured. 試料の評価領域にエネルギー線を入射し、試料を透過したエネルギー線の前記評価領域内における位相分布像を取得し、取得した位相分布像を解析することにより、評価領域における応力分布を測定する。 - 特許庁
To provide a plastic clad optical fiber superior in reliability, moreover, manufactured at a low cost, inhibited in generation of pistoning in a specific temperature range, and reduced in stress of the core fiber of the optical fiber cable, and connectable to a connector without removing the coating. 所定の温度変化範囲におけるピストニングの発生が抑制されるとともに、光ファイバ素線への応力が緩和され、コネクタに被覆を除去することなく接続可能で、しかも、低コストで製造でき信頼性に優れた光プラスチッククラッド光ファイバを提供する。 - 特許庁
At the time of release of a metallic die after the formation of the slider 4, stress concentration on the curvature 51 is avoided, with generation of chips or cracks suppressed, thus attaining enhanced reliability, a reduced defective product ratio, improved productivity, and lowered price of the products. スライダー4の成形後の金型の引き抜き時に、曲率部51への応力集中が回避されて欠けや亀裂の発生が抑制され、ひいては信頼性の向上、製品不良率の低下、生産性の向上及び製品の低廉化を図ることができる。 - 特許庁
In tightening the main metallic shell 50 with thin thickness and the insulating porcelain 10 to form integrally, if the residual stress of the tightening portion 53 is lower, the packing 80 is firmly fitted to the both, so that the air tightness is maintained sufficiently. こうすることで、肉厚の薄い主体金具50と絶縁碍子10とを一体にするための加締めにおいて、加締め部53の残留応力が小さくとも両者とパッキン80とが密着することができ、十分に気密性を保持することができる。 - 特許庁
This cover assembly 48 for the X-ray detector 30 is assembled with a shock absorbing material designed to absorb shock, vibration, the stress, and the strain applied onto the detector 30 when the detector 30 is fallen down or when a load is applied onto the detector 30. X線検出器(30)用カバー・アセンブリ(48)は、検出器(30)を落としたり検出器が負荷を蒙ったりしたときに検出器(30)に加わる衝撃、振動、応力及び歪みを吸収するように設計された衝撃吸収材を組み入れている。 - 特許庁
To prevent damages from cracking or crazing by reducing the stress applied to an exterior material made of a cement-based inorganic plate even if a strain occurs to the building frame due to rolling caused by earthquake or the like as a result of further developing the vertically laying method for exterior facing material proposed previously. これまでに提案している外装材縦張り構造をさらに発展させ、地震などにともなう横揺れにより建物躯体に歪みが生じても、セメント系無機質板からなる外装材に応力が加わりにくく、割れ、ひびなどの破損を防止する。 - 特許庁
To provide a preparation apparatus and a preparation method of a specimen for chemical solution injection preparing a specimen for investigating an improved strength and permeability by injecting a chemical solution to a sample while reproducing the stress state and the construction method in a field. 現地の応力状態や施工方法を再現しながら試料に薬液を注入して改良強度や浸透性の検討を行うための供試体を作製することができる薬液注入供試体の作製装置および作製方法を提供する。 - 特許庁
To provide a butterfly valve capable of preventing the flange part of a seat ring from turning up, eliminating any part with narrow spacing between the flange part and valve stem so as to preclude stress concentration, keeping the sealing force uniformly, and establishing a small-sized construction, large diametric valve stem, and lightweight valve body. シートリングのフランジ部のめくれを防ぎ、しかもフランジ部と弁棒の間隔が狭くなる部分が生じないようにして応力集中を防ぎ、シール力を均一に保って製品の小型化や弁棒の大径化、バルブ本体の軽量化を可能にする。 - 特許庁
To solve the problem wherein an optical part cured and joined by irradiating an ultraviolet curable adhesive with ultraviolet rays at a usual room temperature is deteriorated, for example in its wave front aberration characteristics by the stress strain caused by thermal expansion when the temperature of an apparatus, in which the optical part is incorporated, rises. 通常の室温で紫外線硬化型接着剤に紫外線を照射して硬化・接合された光学部品は、該光学部品を組み込んだ装置の温度が上昇すると、熱膨張による応力歪によって、例えば波面収差特性が劣化する。 - 特許庁
Also, with the provision of a layout inhibition region 21a in a prescribed range from the circumference of the metal post 21 that is affected by stress caused by the metal post 21 at manufacturing, it is inhibited to lay out the devices 33, 35, 37 in the layout inhibition region 21a. また、製造時におけるメタルポスト21に起因して生じる応力の影響を受ける、メタルポスト21の周縁から所定の範囲に素子の配置禁止領域21aを設け、配置禁止領域21aに素子33,35,37を配置しないようにする。 - 特許庁
With this structure, contact stress to be generated by a contact of the ball 6 and the meandering continuous groove 31 can be lowered, and the stabilized differential torque characteristic can be obtained. 第一案内区間31a及び第二案内区間31bを接続する変曲区間a、e、f、g及びhは他の区間より幅及び/又は深さ寸法が大きくされているために、変曲区間a、e、f、g及びhではボール6と溝との接触応力が低減されている。 - 特許庁
To provide a powder conveying device which can be applied to an image formation device performing printing in a high speed, gives low heat stress to powder as a conveyed object, is manufactured in a low cost, and has a long service life, and to provide an image formation device having the powder conveying device. 印刷速度が高い画像形成装置に適用可能な、被搬送物としての粉体に与える熱ストレスが少なく、製造コストが安く、寿命が長い粉体搬送装置、及びこの粉体搬送装置を備えた画像形成装置を提供する。 - 特許庁
To prevent stress concentration from being generated in a transition part of front and rear frames, when the rear frame is formed into a bent shape with respect to the front frame in a frame, or when respective cross-sectional shape dimensions of the front and rear frames are different each other, in addition thereto. フレームにおける前部フレームに対し後部フレームが屈曲する形状とされた場合や、これに加えて、前、後部フレームの各断面の形状寸法が互いに相違する場合において、前、後部フレームの遷移部に応力集中が生じないようにする。 - 特許庁
To provide a method for manufacturing a phase shift mask blank having a light semi-transmission film or a light semi-transmission area with a specified phase angle and transmittance and excellent film characteristics such as good chemical resistance, good light resistance and reduced inner stress, and to provide a method for manufacturing a phase shift mask. 所定の位相角及び透過率を有し、耐薬品性、耐光性、及び内部応力などの膜特性に優れた光半透過膜又は光半透過部を有する位相シフトマスクブランクの製造方法又は位相シフトマスクの製造方法を提供する。 - 特許庁
To prevent stress caused by molding resin from being imposed on the external surface of the cover of a cap, in a molded package that is obtained by mounting a part composed of an inner device and the cap put on it, with a gap in between the device and the cap, on a base material and sealing up them with molding resin. 内部の素子とは隙間を空けて当該素子にキャップを被せてなる部品を、基材に搭載し、これらをモールド樹脂で封止してなるモールドパッケージにおいて、キャップにおける被覆部の外面にモールド樹脂による応力がかからないようにする。 - 特許庁
To provide a method of mirror-polishing a complicated shape body, in which polishing is carried out even if a polishing object has a complicated shape with bumps and dips, even at a deep corner of each dip without generating stress, to finish the polishing object with a mirror surface, and to provide a mirror-polishing device. 研磨対象が溝など凹凸を有する複雑形状体であっても凹部の奥隅について応力なく研磨が行なえて、鏡面に仕上げることができる複雑形状体の鏡面研磨方法および鏡面研磨装置を提供すること - 特許庁
To provide a rolling bearing capable of relaxing the stress concentration due to a contact of a chamfer part of a bearing and a bearing fitting surface at the time of fixing the rolling bearing to a housing or a shaft and capable of realizing the excellent bearing assembly and the application of the axial preload. 転がり軸受をハウジング又は軸へ固定する際の、軸受の面取り部と軸受取り付け面との接触による応力集中を緩和し、良好な軸受組み込み性および確実な軸方向予圧の付加を実現できる転がり軸受を提供する。 - 特許庁
When an ambient temperature is increased, and turned into the transformation start temperature of a wire 53 of the shape memory alloy or more, the wire 53 is restored into the shrinkage shape so that a slider 51 can be drawn downward, and a large stress can be generated in the wire 13, and the operational temperature range can be widened. 環境温度が上昇し、形状記憶合金のワイヤ53の変態開始温度を越えるとワイヤ53は縮み形状に復元し、スライダ51が下方向に牽引されてワイヤ13に大きな応力が発生、動作温度範囲を拡げる。 - 特許庁
To provide a ceramic component for electronic components capable of reducing a coefficient of thermal expansion as well as ensuring a heat transfer property and a conductive property required for a wiring layer, and capable of reducing thermal stress in an interface between the wiring layer and a ceramic substrate, and to provide a method of manufacturing the same. 配線層として必要な伝熱性及び導電性を確保しつつ熱膨張率を低減し、配線層とセラミックス基板との界面における熱応力を低減せしめた電子部品用セラミックス部品、及びその製造方法を提供すること。 - 特許庁