To provide a cross rail clamp device capable of decreasing bending stress of a cross rail generated by reaction force of urging force of a disk spring and pressing force of a clamp jaw part on a fixed support shaft of a clamp arm, while clamp force holdable even by generating an unexpectedly large load at cutting time can be maintained. 切削時に予想外の大きな負荷が発生しても保持できるクランプ力を維持できるとともに、クランプアームの固定支軸に、皿バネの付勢力とクランプ顎部の押圧力との反力により発生するクロスレールの曲げ応力を小さくできるクロスレールクランプ装置を提供する。 - 特許庁
To provide a method of producing a mask blank and a method of producing a transfer mask, for achieving a desired flatness of the mask blank even when a thin film itself has a film stress, and avoiding degradation in positional accuracy of a mask pattern or occurrence of a pattern displacement error and a pattern defect during pattern transfer. 薄膜自体に膜応力がある場合においても、マスクブランクの平坦度が所望の平坦度となり、マスクのパターン位置精度や、パターン転写の際、パターン位置ずれやパターン欠陥が発生することがないマスクブランクの製造方法および転写用マスクの製造方法を提供する。 - 特許庁
To obtain high capacitance and high withstanding voltage by applying a charge-discharge cycle to an electrochemical capacitor until a max. value of stress caused in charging is approximately constant, and removing a cell assembly into a separate capacitor case to form an electrochemical capacitor. 部分的に酸化させた黒鉛類似の微結晶炭素を有する炭素材料を主成分とする分極性電極を用いる電気化学キャパシタにおいて、充電時に応力が発生しても、その応力によってコンデンサ容器の塑性変形が生じない電気化学キャパシタの製造方法を提供する。 - 特許庁
Because it is difficult to propagate heat to the pattern of irregularities during heating the decorative sheet S and also a residual stress which could be unleashed by heat is not accumulated in the resin of the pattern of irregularities part on account of the irregularities formed by machine cutting, the possibilities that the irregularities might be levelled during molding are eliminated. 装飾シートSを加熱した際に熱が凹凸模様のところに伝播し難いことから、また機械切削により凹凸を形成したことで、凹凸模様部の樹脂に加熱によって解放され得る残留応力を蓄積しないことから、成形時に凹凸が戻るようなことがない。 - 特許庁
In this material testing machine 100, a changing speed of a stress or strain in a specimen is detected by a load cell 105 or an extensometer 106, and a pulse number P is determined based on a value of a deviation ΔV between a set target changing speed and a detected actual changing speed to control a rotating speed of a motor 1. 材料試験機100は、供試体の応力または歪みの変化速度をロードセル105や伸び計106により検出し、設定された目標変化速度と検出した実変化速度との偏差ΔVの値によりパルス数Pを決定して、モータ1の回転速度を制御する。 - 特許庁
In the fixing part 60, between a fall-off prevention part 67 and the soldering part 69 to the housing 10, a stress relieving part 68 made deformable according to fluctuations of the housing 10 is arranged and installed in the case the housing 10 is relatively displaced to the base board K because of an external factor such as heat. 固定部60には、ハウジング10に対する抜け止め部67と半田付け部69との間に、熱等の外的要因によりハウジング10が基板Kに対して相対変位した場合に、ハウジング10の変動に応じて変形可能とされた応力緩和部68が配設されている。 - 特許庁
The method for positioning a pipe in a welding of an intersection body is characterized by that protrusions 3a to 3d for positioning which have a height equal to the route gap and the absolute minimum dimensions are provided on the end face of the branch pipe 2 abutted on the main pipe 1 while a stress concentration zone is avoided. 主パイプ1に当接させる枝パイプ2の端面に、ルートギャップに等しい高さをもつ必要最小限の形状寸法の位置決め用突起3a〜3dを、応力集中部を避けて設けたことを特徴とする相貫体溶接時のパイプの位置決め方法である。 - 特許庁
This gear comprises flat surface parts or recessed surface parts 3 and 4 partly at the dedendum thereof having teeth formed on the outer periphery thereof, and is so formed as to distribute a stress acting on the tooth flank 2 thereof according to the number of the engaged teeth engaged with the teeth of a mating gear having a similar flat surface parts and recessed surface parts. 外周に歯が形成された歯車のそれぞれの歯元の一部に、平面部或いは凹面部3、4を有し、同様の平面部或いは凹面部を有する相手方歯車との噛み合い歯数に応じて、歯面2に働く応力を分散可能に構成する。 - 特許庁
In this manufacturing method of a semiconductor device, another silicon oxide film 14 is formed on a second transistor 12, and a silicon oxide film 18 of a predetermined thickness is formed on the second transistor 12 in a prior stage of a process of forming a stress imparting layer 16 covering a first transistors 11, the second transistor 12 and a gate structure 13. 第一のトランジスタ11、第二のトランジスタ12、ゲート構造13を被覆する応力付与層16を設ける工程の前段で、第二のトランジスタ12上に他のシリコン酸化膜14を形成し第二のトランジスタ12上に所定の厚みのシリコン酸化膜18を形成する。 - 特許庁
To provide an energy storage device capable of reducing a stress acting on a positive electrode sheet and a negative electrode sheet when compressing the stacking part of non-painted parts for fixing a current collecting terminal, by reducing a difference in thickness between stacking thickness at an active material painted part and that at the non-painted part. 活物質塗工部での積重ね厚みと未塗工部での積重ね厚みとの厚み差を小さくし、未塗工部の積重ね部を圧縮して集電端子を固定する際に、正極シートや負極シートに作用する応力を緩和し得る蓄電装置を提供する。 - 特許庁
To provide an ultrasonic diagnostic device which is suitable to use in a constrained installation location such as an operating room, a treatment room or the like, which does not place stress on the body of an operator who performs an examination with it and which exhibits portability and versatility. 設置場所に制約を受けるような例えば手術室や処置室などでの使用に適するとともに、超音波診断装置によって検査等を行う術者の身体にかかる負担をなくし、さらに可搬性および汎用性を有する超音波診断装置を提供する。 - 特許庁
To provide an emulsion which has, in addition to emulsion stability, a capability of forming a film at a low temperature and forming a dried coating film which maintains its adhesivity at a low temperature as well as its transparency, and is free from agglomerating and increasing its viscosity even upon subjecting the same to a mechanical stress with a hydrophilic organic solvent and ionic additives added thereinto. 乳化安定性に加え、エマルジョンの低温造膜性、乾燥皮膜の低温接着性及び透明性を維持し、かつ、親水性有機溶剤やイオン性を持った添加剤を添加して、機械的剪断をかけても、凝集、粘度上昇の生じないエマルジョンを得ることを目的とする。 - 特許庁
To attain a manufacturing method capable of suppressing a value of remained tensile stress generated on an inner diameter side portion existing at an inner side in a radial direction smaller than that of a cured layer with formation of the cured layer on an outer peripheral surface of an intermediate part of a hub body 9 by high frequency quenching. ハブ本体9の中間部外周面に高周波焼き入れにより硬化層を形成するのに伴って、この硬化層よりも径方向内側に存在する内径側部分に発生する残留引っ張り応力の値を小さく抑えられる製造方法を実現する。 - 特許庁
Since the base-end side recessed sections 10 are used as the discharge grooves of cutting chips generated at a time when the screw 50 is screwed into the screw hole section 2, the cutting chips are not held between the screw 50 and the screw hole, and stress by the cutting chips is applied and the deformation of the screw hole section 2 can be prevented. 基端側凹部10がねじ50をビスホール部2にねじ込んだ際に発生する切削屑の排出溝になるため、切削屑がねじ50とビスホールとの間に挟まってしまうことがなく、切削屑による応力が加わってビスホール部2が変形することを防止できる。 - 特許庁
This bone fixing tape is formed by braiding the polyester fiber into a tape shape and drawing it and, when it is drawn, the maximum value of Young's modulus measured till the stretch on the stress-strain curve reaches 5% of the original length, is 2 GPa or more. ポリエステル繊維をテープ状に編組し、これを延伸してなる骨固定用テープであって、これを引張したとき、応力・伸長曲線上で伸びが元の長さの5%に達するまでの間に測定されるヤング率の最大値が2GPa以上である、骨固定用テープ。 - 特許庁
To provide an inkjet recorder realizing normal ink ejection by releasing an actuator chip from a contraction stress occurring due to difference of thermal expansion coefficient among constituting members when a thermally expanded inkjet recording head is cooled gradually. インクジェット記録ヘッドが加熱され熱膨張を起こし、その後の除冷時に構成部材の熱膨張係数の違いにより発生する収縮ストレスから、アクチュエータチップを解放し、正常なインク噴射を実現することが可能とするインクジェット記録装置の提供を課題とする。 - 特許庁
This polyolefin stretched film comprises an intermediate layer formed of the described intermediate resin composition between both outer layers formed of the described outer layer resin composition, with such characteristics that a stress to be applied when the film is extended 100% in the TD direction, is 5 to 11 MPa. 下記外層樹脂組成物で形成した両外層間に、下記中間層樹脂組成物で形成した中間層が積層され、MD方向の100%伸長時応力が8〜30MPa、TD方向の100%伸長時応力が5〜11MPaであるポリオレフィン系ストレッチフィルム。 - 特許庁
To provide an aluminum-ceramic composite which has excellent dimensional stability wherein flatness and variation of dimension due to a temperature change or the like under the using environment are extremely small by removing the residual stress of the aluminum-ceramic composite, and is also applicable to a large-sized component. アルミニウム−セラミックス複合体の残留応力を除去することにより、使用環境下での温度変化等による、平面度や寸法の変化量が極めて小さい寸法安定性に優れる大型部品にも適用可能なアルミニウム−セラミックス複合体を提供する。 - 特許庁
To provide a Cu-Ni-Sn-P copper alloy sheet which can meet the recent demand for higher efficiency and higher speed in a press forming process for manufacturing connection parts such as automotive terminal-connector and has a satisfactory strength-ductility balance and also has excellent stress relaxation resistance and electric conductivity. 前記高効率化、高速化した自動車用端子・コネクタなどの接続部品を製造するプレス成形工程に対応し、強度−延性バランスに優れ、同時に、耐応力緩和特性と導電率にも優れさせるCu−Ni−Sn−P系の銅合金板を提供することを目的とする。 - 特許庁
A vibrator 5 set opposite to the surface of a workpiece 3 at a predetermined distance in liquid 2 is vibrated with high frequency to generate cavitation in the liquid, and compressive stress is made to remain on the surface of the workpiece 3 by collapsing impact force of cavitation bubbles. 液体2中で被加工物3の表面から所定距離を隔てて対向するように設置した振動子5を高周波振動させて液体にキャビテーションを発生させ、このキャビテーション気泡の崩壊衝撃力により被加工物3の表面に圧縮応力を残留させる。 - 特許庁
To provide a surface modified stainless steel wherein the corrosion resistance, particularly, stress corrosion cracking is prevented by modifying the surface of stainless steel used in a severe environment, such as piping of nuclear power plant or chemical plant, and to provide a method of treating the surface modified stainless steel. 原子力発電プラントや化学プラントの配管等過酷な環境のもとに使用されるステンレス鋼の表面を改質処理することによって、耐食性、特に応力腐食割れを防止する表面改質ステンレス鋼、表面改質ステンレス鋼の処理方法を提供する。 - 特許庁
To provide a semiconductor element having bumps, of very high stability after connecting, so as to stabilize electric connection to the connecting terminal of a semiconductor mounting substrate, by making the stress applied to the bump uniform, when the element with the bump is pressed against the semiconductor mounting substrate. バンプ付き半導体素子の半導体実装用の基板に押圧するときにバンプに加わる応力を均一にすることにより、半導体実装用の基板の接続端子との電気的な接続の安定化が図られる極めて接続後の安定性が高いバンプ付き半導体素子を提供する。 - 特許庁
To speedily peel off and separate a chip without the occurrence of stress concentration, a damage or breakage at this chip even when the chip is thin and easy to break in a chip separation apparatus which picks up the chip of a semiconductor etc. stuck with an adhesive sheet from the pressure-sensitive adhesive sheet. 粘着シートに貼り付けられた半導体等のチップを該粘着シートからピックアップするチップ分離装置において、チップが薄く破損し易い場合でも該チップに応力集中、傷及び割れを発生させることなく、しかも高速で該チップを剥離させて分離できるようにする。 - 特許庁
To obtain a glycine-enriched vegetable feed composition capable of supressing harmful effects such as death due to heat stress given to hens raised with the entire vegetable feed in summer season to the extent equal to or less than that given to hens raised with animal formula feed. 夏季において全植物性飼料で飼育した採卵鶏にみられる暑熱ストレスによる熱死等の弊害を動物性配合飼料で飼育した採卵鶏と同等またはそれ以下に抑制し得る採卵鶏用の全植物性飼料組成物を提供する - 特許庁
To provide a fuel treatment device for a fuel cell capable of (1) reducing thermal stress due to generation of high temperature in the vicinity of a reformer inlet and also a radiation loss, (2) preventing deterioration of performance by suppressing a bypass flow even by providing a thin reaction vessel and generating a clearance in an upper part. (1)改質器入口付近の高温化による熱応力を低減し、かつ放熱損失も低減でき、(2)薄い反応容器であっても上部に隙間ができてもバイパス流を抑制して性能低下を防ぐことができる燃料電池用燃料処理装置を提供する。 - 特許庁
To provide a semiconductor device which enables a flip chip connection without the need for an underfill resin and the blow-out of a fuse is enabled based on the test result of electrical characteristics in a WLCSP including a stress relief layer, and moreover, the sealing of the upper part of the fuse can flexibley be dealt with. アンダーフィルの不要なフリップチップ接続を可能にするとともに、応力緩和層を設けるWLCSPにおいて、電気的特性の検査結果をもとにヒューズの切断を可能にし、このヒューズの上部の封止に柔軟に対応することができる半導体装置を提供する。 - 特許庁
The thermoplastic resin composition comprises inorganic particles having 20-300nm diameters calculated in terms of BET specific surface area finely dispersed in a thermoplastic resin having ≤3×10^4 weight-average molecular weight ground under shear stress equal to or higher than interparticle cohesive force of the inorganic particles. BET比表面積換算径が20〜300nmである無機粒子が、重量平均分子量3×10^4以下である熱可塑性樹脂内に、無機粒子の粒子間凝集力相当以上の剪断応力で解砕されて微分散していることを特徴としている。 - 特許庁
To enable recording and measuring even during dark time which is an active time for a nocturnal animal, reduce the contact of an experimenter to a test animal during, and before and after experiment as far as possible, reduce nociceptive stress to the test animal, and measure and evaluate memorizing and leaning ability under these conditions. 夜行性動物の活動期である暗期にも記録測定できること、実験者による被験動物への接触を実験中、実験前後を通じて極力減らすこと、被験動物に対する侵害ストレスを減らすこと、及びその条件で記憶学習能力を測定評価することにある。 - 特許庁
To improve reliability of electrical and mechanical connection between a heat generating heater and an intermediate shaft, to improve heat generation performance of the heat generating heater, and to prevent damage of the intermediate shaft or the heat generating heater accompanying concentration of stress without increasing manufacturing cost. 発熱ヒータ及び中軸間の電気的かつ機械的な接続信頼性の向上、及び、発熱ヒータの発熱性能の向上を図ることができ、さらには、生産コストの増大等を招くことなく、応力の集中に伴う中軸や発熱ヒータの破損を防止する。 - 特許庁
To restrain stress concentration by centrifugal force in high speed operation, to reduce noise by a wind roar in the high speed operation, and to restrain deformation, a burr and a return due to fastening, while having a structure for locking a fastening tool on a nut. ナットに締付け治具が係止される構造を持ちながら、高速運転時に遠心力による応力集中を抑えることができ、また、高速運転時の風切り音による騒音を低下することができ、締付けによる変形及びバリやかえりを抑えることができる。 - 特許庁
The polyester resin layer (A) is preferably structured of a rubber-like elastic body resin (B) which is finely dispersed as the expansion stress relaxation agent in the polyester resin (A) which is a matrix and is at least partially encapsulated by a vinyl polymer (C) having a polar group. 好ましくは、ポリエステル樹脂層(A)が、マトリックスとしてのポリエステル樹脂(A)中に伸縮応力緩和剤としてゴム状弾性体樹脂(B)を微分散したものであり、かつ少なくともゴム状弾性体樹脂(B)の一部が極性基を有するビニル重合体(C)でカプセル化された構造を有している。 - 特許庁
To provide a semiconductor device that can suppress curving of a semiconductor element due to a difference in thermal expansion coefficient between the semiconductor element and a substrate to which the semiconductor element is mounted, can reduce the internal stress of the semiconductor element, and can improve the degree of freedom in structural design of the semiconductor element. 半導体素子とこの半導体素子が搭載される基板との熱膨張係数の差に起因する半導体素子の反りを抑制でき、半導体素子の内部応力を低減し、半導体素子の構造設計自由度の向上を可能とする半導体装置を提供する。 - 特許庁
To provide an image forming method for stably obtaining images of high quality for a long period of time by enhancing a function of protecting an image carrier surface, in particular, from stress in a charging step and a cleaning step and suppressing soiling of a charging member. 像担持体表面の保護、特に帯電工程ならびにクリーニング工程でのストレスに対する保護機能を高め、かつ帯電部材の汚れを抑制することにより、良好な品質の画像を長期間に亘り安定して得ることができる画像形成方法を提供する。 - 特許庁
Wiring coating layers 5 and 5', which cover a lower wiring layer 3a and an upper wiring layer 3b composed of Au on or above a compound semiconductor substrate 1 and are composed of tantalum or titanium that is a metal having a smaller thin film stress than Au and having a high melting point than Au, are formed by sputter. 化合物半導体基板1上の、Auからなる下部配線層3aと上部配線層3bの上部を覆って、Auより薄膜応力が小さく高融点を有する金属であるタンタルあるいはチタンからなる配線被覆層5と5’をスパッタにより形成する。 - 特許庁
The hand 1 can reduce fractures in the wafer 10 even while moving up as shown in Fig. 4 (c) by controlling moving up amount D1 and D2 of pistons 18 and 7a of cylinders 6a, 6b and 7 so as to minimize stress applied to the wafer 10. このハンド1は、図4(C)に示す引き上げ途中段階においても、各シリンダ6a,6b,7のピストン18,7aの引き上げ量D1,D2を調整することで、ウェハ10に生じる応力を最小となるようにして、引き上げ時のウェハ10の割れを低減することができる。 - 特許庁
Consequently, amount of developer to be drawn up can be controlled and stress to be applied on the developer can be controlled to prevent the occurrence of image defects including unevenness in density, roughness, fogging or the like and form images stably over a long period of time. それによって現像剤の汲み上げ量を制御することで現像剤に掛かるストレスを制御することが可能となり、濃度ムラ、がさつき、かぶりなどの画像不良を抑制し、長期にわたり安定した画像形成を行うことができる画像形成装置を提供することができた。 - 特許庁
To provide a cosmetic composition which recovers, maintains or strengthens the moisture retention of skin, and/or protects skin from various kinds of stress, and/or prevents or retards the appearance of indicium of aging of skin, or weakens the effect, or accelerates the long life of a cell or a tissue. 皮膚の保湿を回復、維持、又は増強する、及び/又は皮膚を様々な種類のストレスから保護する、及び/又は皮膚の老化の兆候が現れるのを防ぐ若しくは遅らせる、又はその効果を弱める、或いは細胞又は組織の長寿命を促進する組成物を提供する。 - 特許庁
Since the stress applied to the first connection pad 2a can be relaxed effectively by the second connection pad 2b, the first connection pad 2a can be electrically connected surely with the terminal pad of an external electric circuit board over a long term together with the second connection pad 2b. 第1の接続パッド2aにかかる応力を第2の接続パッド2bによって効果的に緩和することができるため、第2の接続パッド2bとともに第1の接続パッド2aを外部電気回路基板の端子パッドに対して長期にわたって確実に電気的接続させておくことができる。 - 特許庁
The structure is provided with two base plates 25 for fixing the structure on a base 3, a holding action part 27 formed between two base plates, and deforming action parts 29 formed between respective base plates and the action part, and stress concentration parts 35 and 37 are formed at the deforming action parts 29. 基台3に固定するための2つのベース板25と、2つのベース板の間に形成される保持作用部27と、各ベース板と保持作用部との間に形成される変形作用部29とを備えており、変形作用部29には応力集中部35、37が形成されている。 - 特許庁
In the shaded domain in the diagram, a relationship is set between the compression residual-stress imparted by nitriding treatment of the metal ring in the innermost layer which is forced by contact load in contact with the saddle face of an metal element, and the ratio of a diameter in the free-state of the metal ring and the smallest winding diameter which has expressed dimensionlessly. 金属エレメントのサドル面に接触して接触荷重を受ける最内層の金属リングを窒化処理して与えられる圧縮残留応力と、最小巻付半径で無次元化した金属リングの自由状態径との関係を斜線の領域に設定する。 - 特許庁
To prevent the generation of a stress concentration to a support, even though a large force directing to a body side is operated to a pair of connection plates in an earthquake time, to a rack using the support furnishing the connection plates which are extended in parallel each other at a specified interval narrower than the width of the man body. 本体の幅より狭い所定間隔で互いに平行に延びる一対の連結板部を開口側に備えた支柱を使用したラックに、地震の際に本体側に向かう大きな力が連結板部に作用しても、支柱に対する応力集中の発生を防止する。 - 特許庁
To make the bonded parts of terminal members to external electrodes hard to break down, even if stress is applied to the terminal members in a laminated ceramic capacitor of a structure, where the terminal members consisting of a metal plate are bonded to the external electrodes of a laminated ceramic capacitor element made of a conductive bonding material, such as solder. 半田等の導電性接合材によって積層セラミックコンデンサ素子の外部電極に金属板からなる端子部材が接合された、積層セラミックコンデンサにおいて、端子部材に応力が加わっても、端子部材と外部電極との接合部分が破壊されにくいようにする。 - 特許庁
The joint structure with a stable stress for supporting a load is obtained by inserting the extension leg material into the joint member since both an extra extension leg material and a corrugated leg material having a similar shape give many sides for the connecting surfaces and produce greater friction, and the entire height is adjusted. さらに考案した継手部材に差し込む連設は、別途伸長脚材及び波型形状脚材の両脚材と近似形状であるため接続面の多面性及び摩擦力が向上し、安定した支持応力を持たせる継手構造となり、全体の高さ調整を可能にする。 - 特許庁
To provide a rotary-electric machine which enables the higher revolution of a rotor by constituting it so that the stress generated in the magnet due to the centrifugal force at rotation of the rotor may not increase thereby enlarging the operation range, and also can secure the tenacity of a magnet at rotation of a rotor without enlarging a magnet holder. ロータ回転時の遠心力による磁石への発生応力が増加しないようにして、運転範囲を拡大しロータの高回転化を可能にすると共に、磁石保持部を大型化することなくロータ回転時の磁石の保持強度を確保することができる回転電機を提供する。 - 特許庁
The fixing structure of the large-sized capacitors prevents the solder connection portion from being broken by fixing the plurality of large-sized capacitors 2 with a fixing clamp 5 for fixing them together and then preventing the large-sized capacitors from swinging owing to a fall or vibration to reduce stress applied to the solder connection portion 3. 本発明は、複数個の大型コンデンサ2を一括固定する固定具5にて固定することにより、落下、振動による大型コンデンサの揺れを防止し、ハンダ接続部3に印加される応力を緩和することによりハンダ接続部の破損を防止する大型コンデンサの固定構造とする。 - 特許庁
In the process where an inner column 10b made of the metallic plate is pushed in the outer column 9b by the impact load associated with a secondary collision, the respective projection parts 26, 26 are scraped away while a shearing stress is applied to the respective projection parts 26, 26 by the rear end edge of the inner column 10b. 金属板製のインナコラム10bが二次衝突に伴う衝撃荷重により上記アウタコラム9b内に押し込まれる過程で、このインナコラム10bの後端縁により上記各突条部26、26に剪断応力を加えつつこれら各突条部26、26を削り取る。 - 特許庁
To provide a method for manufacturing a round steel tube, which can manufacture a round steel tube without performing manual conditioning work even when the round steel tube has a thick wall and a large diameter, can improve the quality of weld zone, and can easily and securely manufacture the round steel tube having no residual stress and sufficient toughness. 例え厚肉、大径であったとしても、手作業による精整作業を行うことなく得られ、溶接部の品質も改善し得、残留応力がなく、十分な靱性を有する丸鋼管を容易に確実に製造し得る丸鋼管の製造方法を提供する。 - 特許庁
In the polishing method for polishing a surface to be polished by pressing polishing pad rotated by a motor to the surface to be polished, the torque of the motor is controlled to control a stress in the intra-surface direction of the surface to be polished. 本発明の研磨方法は、モータにより回転駆動される研磨パッドを被研磨面に押し付け、当該被研磨面を研磨する研磨方法において、前記モータのトルクを制御し、前記被研磨面の面内方向における応力成分を制御することを特徴とする。 - 特許庁
To provide a profile extrusion molding rubber compound excellent in a ratio of residual compressive stress which is an index of shape retention characteristics and BIT balance which is an index of kneadability, and having dynamic characteristics equal to those of vulcanized rubber obtained by using conventional ethylene-α-olefin-nonconjugated diene copolymer. 形状保持特性の指標となる残存圧縮応力率と混練性の指標となるBITのバランスに優れつつ従来のエチレン−α−オレフィン−非共役ジエン共重合ゴムを用いて得られる加硫ゴムと同等の力学特性を有する異型押出しゴム配合物を提供する。 - 特許庁
Such a loosely connected connector does not transmit all the force among connected components, and the movement among the loosely connected components can fully block the stress caused by solder bonding. カバーは、フレームに移動可能に取着されていて、ハウジングの案内構造部に対応する案内構造部を有していて、それによってカバーがハウジングと整列し第1の位置と第2の位置との間で移動可能であり、また、開口部を有していて、それによって接触子が電気的構成部品の端子を係合できる。 - 特許庁