「SW.」を含む例文一覧(1704)

<前へ 1 2 .... 6 7 8 9 10 11 12 13 14 .... 34 35 次へ>
  • Fourth, the section C2 again conducts charging of the capacitor CD while the section SW is turned off.
    第4に、スイッチ部SWをオフ状態にして、再度、第2充電部C2が内部容量CDに対して充電を行う。 - 特許庁
  • A switching control circuit 20 generates a control signal SW for switching circuits 16, 18 based on digital data D.
    切換制御回路20は、デジタルデータDに基づいてスイッチ回路16,18に対する制御信号SWを生成する。 - 特許庁
  • A tread part 2 has a grounding swell portion 2A forming a tread grounding surface S whose width is 55 to 70% of an overall tire width SW.
    トレッド部2に、タイヤ総巾SWの55〜70%の巾のトレッド接地面Sをなす接地隆起部2Aを設ける。 - 特許庁
  • A CPU 20a controls a SW transistor Tr_0 so as to turn off when a gas sensor 30 detects no gas leak.
    CPU20aは、ガスセンサ30によってガス漏れが検出されていないとき、SWトランジスタTr_0をオフ制御する。 - 特許庁
  • An SW 201 performs switching either to connect an input terminal of a receiver 133 to an antenna 114 or to terminate it.
    SW201は、受信機133の入力端を、アンテナ114に接続するか又は終端するかを切り換える。 - 特許庁
  • Namely, the batch reset SW in this case is an operation element for instructing a stop of the batch update of all the channels.
    すなわち、この場合の一括解除SWは、全チャンネルの一括更新の停止を指示するための操作子である。 - 特許庁
  • In a movable Yakumono (accessory), a state of a switch SW is read when a latch signal SLAT is LO (data D1-D8).
    可動役物では、ラッチ信号SLATがLOのタイミングでSWの状態が読み込まれる(データD1〜D8)。 - 特許庁
  • A weight/correction value calculation part 4 calculates transmission weight SW to control directivity of transmission of an array antenna 1.
    ウェイト・補正値算出部4は、アレイアンテナ1の送信の指向性を制御するための送信ウェイトSWを算出する。 - 特許庁
  • The switch SW interrupts one electrode of the capacitor C1, the first electrode A1 and one end of the silicon symmetric switch S.
    スイッチSWは、キャパシタC1の一方の電極と、第1電極A1およびサイダックSの一端と、を断続する。 - 特許庁
  • A speaker device 20 and an SW 30 respectively receive audio stream data from an external communication device to start sound emission.
    スピーカ装置20とSW30は、外部の通信装置からオーディオストリームデータを各々受信して放音を開始する。 - 特許庁
  • The drive device 1 has an inverter circuit 4 which supply drive signals Su, Sv, Sw to the coils respectively.
    駆動装置1は、コイルに前記駆動信号Su、Sv、Swをそれぞれ供給するインバータ回路4を備える。 - 特許庁
  • In this transmission and reception system, an inquiry switch (SW) 1 instructs a baseband (BB) part 2 to start a search operation.
    送受信システムにおいて、インクワイアリースイッチ(SW)1は、ベースバンド(BB)部2に対する探索動作の開始を指示する。 - 特許庁
  • The control part 25 synchronizes the writing of data to a rate conversion memory 26 and a head SW signal with the FR signal.
    制御部25は、レート変換メモリ26へのデータの書き込み及びヘッドSW信号を、FR信号に同期させる。 - 特許庁
  • The amount SW of bulge and the flatness PN are in the relation of trade-off to the draft in a horizontal rolling stage.
    水平圧延工程における圧下率に対して、膨らみ量Swと平坦度PNとはトレードオフの関係にある。 - 特許庁
  • When the Vsi exceeds 5 (ST11), the selecting SW 28 is switched to a transfer roller 34 side, and the adjustment is finished.
    Vsiが5を越えると(ST11)、セレクトSW28を転写ローラ34側に切り換え、調整を終了する。 - 特許庁
  • When the main board 1 is removed, the contact C of the switch SW is turned off to stop the supply of the backup power source.
    メイン基板1が外された場合に、スイッチSWの接点Cがオフになり、バックアップ電源の供給がなくなる。 - 特許庁
  • By controlling the ON/OFF of the switch SW by the control circuit, the operations of proximity sensors 2...2 are controlled in the time division manner.
    制御回路がスイッチSWをオンオフ制御することによって、近接センサ2…2の動作を時分割制御する。 - 特許庁
  • A plurality of the connectors CP1 and CP2 are connected to the side wall member SW or a member in the space IS, respectively.
    複数の連結部CP1、CP2は、側壁部材SW又は空間IS内の部材にそれぞれ連結されている。 - 特許庁
  • A detection operation control part 8 closes the normally open switch circuit SW when a circuit breaker 2 is opened.
    検出動作制御部8は、遮断器2が開状態になっているときに、常開スイッチ回路SWを閉状態にする。 - 特許庁
  • The supply of a backup power source 2b to a RAM 2c disposed in a sub board 2 is made through a contact C of a switch SW.
    サブ基板2にあるRAM2cへのバックアップ電源2bの供給をスイッチSWの接点Cを介して行う。 - 特許庁
  • A second comparator 20 generates the control signal Sc responding to the limit signal Sa and period signal Sw.
    第2のコンパレータ20はリミット信号Saと周期信号Swとに応答して制御信号Scを発生する。 - 特許庁
  • A switch SW 1 is provided between a connection point 106 between the coupling capacitor C1 and the connector 110, and a ground terminal.
    スイッチSW1は、カップリングキャパシタC1とコネクタ110の接続点106と、接地端子との間に設けられる。 - 特許庁
  • In the pachinko machine, MIC indicates a microphone for inputting voice of a player, SW a microswitch and SP a speaker.
    パチンコ遊技機において、MICは遊技者の音声を入力するマイクロフォン、SWはマイクスイッチ、SPはスピーカである。 - 特許庁
  • While the switch SW is OFF, the output of the comparator circuit 4 is set so as to bring the surround mode into active state.
    スイッチSWがOFFのとき、サラウンドモードが動作状態となるよう前記比較回路4の出力を設定する。 - 特許庁
  • To solve a problem that it cannot be easily distinguished that the cause of an emergency stop is due to the operation of an emergency stop SW or the disconnection of a circuit in a mobile machine control system having an attachable/detachable teaching operation device with an emergency stop SW.
    非常停止SWを備えた着脱可能な教示操作装置を有する可動機械制御システムにおいて、非常停止の原因が、非常停止SWの操作によるものか、回路の断線によるものかを容易に確認できない。 - 特許庁
  • This pneumatic tire is 0.75-0.95 in the ratio TW/SW of a tread width TW to a tire maximum width SW between the tread end Te in a normal state of being no-load of being installed in the normal rim and being filled with normal internal pressure.
    正規リムに装着されかつ正規内圧が充填された無負荷である正規状態において、トレッド端Te間のトレッド幅TWとタイヤ最大幅SWとの比TW/SWが0.75〜0.95である空気入りタイヤである。 - 特許庁
  • An acquisition unit 312 acquires information indicating the start port type of the A first start port 105 or the B first start port 125 for which a game ball is detected by an A first start port SW 220 or a B first start port SW 221.
    取得部312は、遊技球が甲第1始動口SW220または乙第1始動口SW221によって検出される、甲第1始動口105または乙第1始動口125の始動口種別を示す情報を取得する。 - 特許庁
  • A SW resource waiting process count part 112 calculates the number of waiting processes to each software resource in the HW unused state, and an output part 114 outputs a calculation result with a SW resource having a large waiting process number as a bottleneck.
    また、SW資源待ちプロセスカウント部112は、HW未活用状況時における各ソフトウェア資源に対する待ちプロセスの数を算出し、出力部114は、待ちプロセス数の多いSW資源をボトルネックとして、算出結果を出力する。 - 特許庁
  • This circuit is a voltage detection circuit operated on output voltage, and monitors the input power voltage of a switching regulator and turns off a switching element, when the input power voltage of the switching regulator is lower than the operating voltage of a switching regulator control circuit.
    出力電圧で動作させる電圧検出回路で、SWレギュレータの入力電源電圧を監視し、SWレギュレータ制御回路の動作電圧よりもSWレギュレータの入力電源電圧が低下したときに、SW素子をOFFさせるようにした。 - 特許庁
  • A information processing system 7 (or 10) monitors fault information, the ID and number-of-versions information of HW, FW and SW, etc., by using monitoring SW and transmits monitoring information to an information processing system 1 to be the remote maintenance device.
    情報処理システム7(又は10)では、監視SWにより障害情報やHW、FW、SWのID及び版数情報等を監視し、その監視情報をリモート保守装置としての情報処理システム1に送信する。 - 特許庁
  • An operation indication lamp for lighting up when supply of power to the lighting load is arranged on a box 1 of the automatic photoelectric blinking device SW, and the automatic photoelectric blinking device SW is organized to know from the outside whether or not the power is supplied to the lighting load.
    光電式自動点滅器SWの筐体1に、照明負荷への電力の供給時に点灯する動作表示灯を設け、照明負荷に電力が供給されているか否かを外部から知ることができる構成とする。 - 特許庁
  • A press finishing SW 14 acting as a starting switch of a lifting drive mechanism of a press finishing element 4 and a thread cutting SW 15 acting as a starting switch of a thread cutting device are connected to a control means 11 for controlling a switching operation of a light emitting means 3.
    発光手段3のスイッチングを制御する制御手段11には、押エ金4の上昇駆動機構の起動スイッチである押エ金上げSW14、および糸切り装置の起動スイッチである糸切りSW15が接続されている。 - 特許庁
  • A vehicle BD is provided with an operation unit 70 (an operation means) having a bringing-out SW 71 and a storage SW 72 (an operation switch) in each of which an on state is held by a single switch operation, for previously instructing a drive mode of the seat 10.
    車両BDには、一度のスイッチ操作でオン状態が保持される振出SW71及び格納SW72(操作スイッチ)を有し、シート10の駆動モードを予め指示しておくための操作ユニット70(操作手段)が設けられる。 - 特許庁
  • When the voltage Vo increases, the collector current in the transistor Q is generated, and the photo diode in the photo coupler PC becomes 'on', and the photo transistor becomes conductive, and the emitter current Id is flown to the CT terminal, and the width of the outputted pulses in SW-Reg is narrowed, and the output voltage Vo is lowered to the normal value.
    電圧Voの上昇でトランジスタQのコレクタ電流が流れ、フォトカプラPCのフォトダイオードがオンし、フォトトランジスタが導通し、エミッタ電流IdがCT端子に流れ、SW-Regの出力パルスの幅が狭まり、出力電圧Voが正常値に下がる。 - 特許庁
  • A pressure sensor 13 provided in a rotary mechanism section of a focusing mechanism 12 of a camera 7 generates a signal by the adjustment operation of the user, and an SW controller 14 activates a control signal of a video changeover SW 16 when a detection section is active.
    カメラ7のピント合わせ機構12の回転機構部に設けた圧力センサ13はユーザの調整操作で信号を発し検出信号がONの間SW制御装置14は映像切り替えSW16の制御信号をONにする。 - 特許庁
  • A transmission pulse is transmitted to the source of switching elements SW0-SW15 at a timing when the switching elements SW are turned on, and a vibrator S where the transmission pulse is given from the drain of the switching elements SW transmits ultrasonic waves to an object to be inspected.
    スイッチング素子SWがオンしたタイミングで、各スイッチング素子SW_0 〜SW_15のソースに送信パルスが送信され、当該スイッチング素子SWのドレインから送信パルスが与えられた振動子Sは、超音波を被検査物に送信する。 - 特許庁
  • The shift position detection device is provided with seven switches to detect the shift position selected by a shift lever and the intermediate position, and the SW signal of the individual shift device is changed from ON to OFF or from OFF to ON and then to OFF again when the shift lever is moved.
    シフトレバーにより選択されたシフトポジションおよび中間位置を検出するスイッチを7つ設け、各シフトデバイスSW信号を、シフトレバーをストロークさせたとき、オンからオフ、またはオフからオンへと移行後再びオフとなるように設定した。 - 特許庁
  • The semiconductor device includes: a sense amplifier SA amplifying potential difference of global bit lines GBL1, GBL2; a plurality of hierarchical switches SW connected to the global bit lines GBL1, GBL2; memory mats MAT1, MAT2 including a plurality of local bit lines connected respectively to the global bit lines GBL1, GBL2 through the hierarchical switch SW; and a control circuit activating the hierarchical switch SW.
    グローバルビット線GBL1,BGL2の電位差を増幅するセンスアンプSAと、グローバルビット線GBL1,BGL2に接続された複数の階層スイッチSWと、階層スイッチSWを介してグローバルビット線GBL1,GBL2にそれぞれ接続される複数のローカルビット線を含むメモリマットMAT1,MAT2と、階層スイッチSWを活性化させる制御回路と、を備える。 - 特許庁
  • Before operation start of an inverter, only a switch KO is conducted with switches K11, K12 opened in a switching group SW.
    インバータの運転開始に先立ち、スイッチ群SWにおいてスイッチK11,K12を開放したまま、スイッチK0のみを導通する。 - 特許庁
  • To prevent automatic informing of faults in a communication by the difference of the falling property of a power source in an apparatus when a main SW turns off.
    メインSWがオフするときの装置内の電源の立下り特性の相違による通信異常の自動報知を防止。 - 特許庁
  • An AC code reduction device 21 receives data of a B picture decoded by a VLD(variable length code decoder) 13 via a SW 15.
    VLD器13で復号されたBピクチャのデータは、SW15を経由してAC符号削減器21に入力される。 - 特許庁
  • The lighting control system is provided with a plurality of blinking type guide lamps A, a guide lamp signal device, and an opening and closing switch SW.
    照明制御システムは、複数個の点滅形誘導灯Aと、誘導灯信号装置と、開閉スイッチSWとを備える。 - 特許庁
  • The placing plate (153) is detachably placed on a base table (52) by each of substrates (SW) in different sizes to be exposed.
    載置プレート(153)は大きさの異なる被露光基板(SW)ごとにベーステーブル(52)に載置される着脱可能な載置プレートである。 - 特許庁
  • A high frequency SW 88 is provided to an output path of the incoming signal, which connects the output path only when the reference signal is detected.
    上り信号の出力経路には高周波SW88を設け、基準信号を検出したときにだけ接続する。 - 特許庁
  • When the center of an operating body 31 is pushed in, a pressure rod 32 presses a thin type switch SW, and click operation is detected.
    操作体31の中心を押し込むと、押圧棒32が薄型スイッチSWを押圧し、クリック操作の検出が行われる。 - 特許庁
  • When it is determined that an IG-SW is turned OFF (S1), a processing part of the open voltage value estimation device causes a timer to measure a time (S2).
    開放電圧値推定装置の処理部は、IG−SWがオフされたと判定した場合(S1)、タイマに計時させる(S2)。 - 特許庁
  • The 'analog SW part 1' becomes a part which determines which mode a connection is made to with an externally inputted select signal 5.
    「アナログSW部1」は、外部より入力されるセレクト信号5により、どのモードと接続するか決定する部分となる。 - 特許庁
  • A base station control unit terminates the input terminal of the receiver using the SW 201 and inputs thermal noise in the LNA 205.
    基地局制御部は、SW201により受信機の入力端を終端して、熱雑音をLNA205に入力させる。 - 特許庁
  • When the main board 1 is removal, a contact C of the main board SW is turned off and the supply of the backup power source is stopped.
    メイン基板1が外された場合に、スイッチSWの接点Cがオフになり、バックアップ電源の供給が行われなくなる。 - 特許庁
  • Second, a second charging section C2 conducts charging of an internal capacitor CD while maintaining the off condition of a switch section SW.
    第2に、スイッチ部SWをオフ状態に保ったまま、第2充電部C2が内部容量CDに対して充電を行う。 - 特許庁
<前へ 1 2 .... 6 7 8 9 10 11 12 13 14 .... 34 35 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.