「Spring pressure」を含む例文一覧(2218)

<前へ 1 2 .... 17 18 19 20 21 22 23 24 25 .... 44 45 次へ>
  • To provide a seat for a vehicle capable of providing a load detection means such as a pressure receiving member without being affected by a frame of a seat and the structure of a spring system.
    シートのフレームやばね系の構造の影響を受けずに受圧部材等の荷重検出手段を設けることができる車両用シートを得る。 - 特許庁
  • When pressure by the substrate 100a is released, the support table 17 moves to a support position for supporting the stacked substrates 100b by biasing force of a spring.
    また、この基板100aによる押圧が解除されると、支持台17は、バネの付勢力により積層された基板100bを支える支持位置に移動する。 - 特許庁
  • A tensile force spring 56 biases the tension roller 15 in the direction for increasing belt tensile force and in the direction for extending center distance between the pressure roller 14 and it.
    張力ばね56はテンションローラ15をベルト張力が大きくなる方向、加圧ローラ14との軸間距離を長くする方向に付勢する。 - 特許庁
  • By the superimposition of the repulsive force of this spring 11 and the inflation pressure of the curtain airbag 8, the lower edge of the roof lining 4 is pressed strongly to the inner side of the cabin.
    このスプリング11の反発力と、カーテンエアバッグ8の膨張圧力とが重畳してルーフライニング4の下縁を車室内方へ強力に押圧する。 - 特許庁
  • This clutch cover assembly 1 includes: a clutch cover 2; a pressure plate 3; a diaphragm spring 5; a wear amount detecting mechanism 6; and a wear following mechanism 7.
    本クラッチカバー組立体1は、クラッチカバー2と、プレッシャプレート3と、ダイヤフラムスプリング5と、摩耗量検出機構6と、摩耗追従機構7と、を備えている。 - 特許庁
  • To provide a clutch control device capable of detecting the overall axial change distances of a pressure plate and a diaphragm spring by an adjusting mechanism.
    調整機構によるプレッシャプレート及びダイヤフラムスプリングの軸方向の総変更距離を検出することができるクラッチ制御装置を提供する。 - 特許庁
  • A high-voltage terminal electrically connected to the high-pressure side end part of a secondary coil and a coiled spring in contact with the high-voltage terminal are disposed at the plug mounting port.
    プラグ取付口には、2次コイルの高圧側端部と電気的に接続された高圧端子及び高圧端子に接触するコイルバネが配設されている。 - 特許庁
  • To provide a pneumatic brake actuator as improvement of the conventional arrangement in which a spring-loaded brake actuator is installed being sealed tightly to arouse a problem of pressure rise and producing a vacuum.
    スプリング式ブレーキアクチュエータが密閉され、かつ圧力上昇および真空生成の問題が改善される空気式ブレーキアクチュエータを提供する。 - 特許庁
  • To provide a suspension device capable of further lowering a car height during non-pressure of an air spring and especially being used as a car height regulation type.
    エアスプリングの無圧時の車高を一層下げることができる、特に車高調整式として用いられる懸架装置を提供することを目的とする。 - 特許庁
  • When the inside of the storage pipe 30 is brought into negative pressure or pushed from above, the valve member 36A is opened against an urging force of the spring 36B.
    収納管30内が負圧になったり、上方からの押圧があったりすると、スプリング36Bの付勢力に抗して弁部材36Aは開放される。 - 特許庁
  • The latch bolt 36 engaged with the strike 40 recedes while compressing the coiled spring 37 under the high pressure introduced into the strike 40, so as to be disengaged from the strike 40.
    ストライク40に係合しているラッチボルト36はストライク40に導入される高圧でコイルスプリング37を圧縮して後退し、ストライク40から外れる。 - 特許庁
  • When a cap member 26 is separated away from a cap mounting part 24, a valve element 58 is moved upward through the force of a coil spring 82, which forces the valve element into pressure contact with a valve seat part 80.
    キャップ部材26をキャップ取付部24から離脱させると、コイルスプリング82が弁体58を上方へ移動させて弁座部80へ圧接させる。 - 特許庁
  • The capacity of the vibration resisting pressure chamber can be changed with the movement of the movable piston body, and so the spring stiffness of the vibration resisting unit can be easily adjusted.
    可動ピストン体を移動させることで除振圧力室の容積を変更できるので、除振ユニットのばね剛性を簡単に調整できる。 - 特許庁
  • A spring 40 bringing the cam projection 34a into pressure contact with the cam face 32a is provided and the cam projection 34a is made displaceable in the direction of the bore of the support 34.
    カム突起34aをカム面32aに圧接させるバネ40を設け、カム突起34aを受け台34の内径方向に変位自在とする。 - 特許庁
  • A spring is incorporated in the forward clutch provided at a power transmission path, for holding the forward clutch in a slipping state during an engine shutdown that suffers from reduced oil pressure.
    動力伝達径路に設けられる前進クラッチには、油圧が低下するエンジン停止時に滑り状態等に保持するためのスプリングが組み込まれる。 - 特許庁
  • The second spring 600 releases engagement of the rotor 200 and the second intermediate member 400 when negative pressure in the housing 100 gets to the prescribed value or higher.
    第2スプリング600は、ハウジング100内の負圧が所定値以上となった場合に、ロータ200と第2中間部材400との係合を解除する。 - 特許庁
  • The blade 108 is fixed on a pedestal 109, which is supported to rock with a shaft 109a as center and energized by a pressure adjusting spring 110.
    クリーニングブレード108は、台座109に固定し、台座109を軸109aを中心に揺動可能に支持し、圧調整ばね110で付勢する。 - 特許庁
  • Since oil pressure is dissipated at a start-up or at an anomaly of the system, the urging force of a spring 144 can press a pin 148a against a guide portion 130.
    装置異常時には油圧が消失するため、スプリング144の付勢力によりピン148aをガイド部130に当接させることができる。 - 特許庁
  • High pressure air is supplied to or discharged from the air spring 14 by a leveling valve 18 so that an interval between base plates 10 and 11 will have a set value.
    ベース板10,11の間隔が設定値になるよう、レベリングバルブ18によって空気ばね14に高圧空気を供給又は排出する。 - 特許庁
  • A set value of the expansion valve 1 is adjusted by varying the amount of screwing of the pressure sensor 22 to vary a load of the compression coil spring 9.
    膨張弁1のセット値は、圧力センサ22のねじ込み量を変化させて圧縮コイルスプリング9の荷重を変化させることによって調節される。 - 特許庁
  • When the internal pressure of the battery rises, a fluid is discharged from the battery through the flow hole 611 against the repulsive force of the coil spring 64.
    電池の内圧が上昇した場合は、コイルばね64の反発力に逆らって電池内から流体が通流孔611を通って排出される。 - 特許庁
  • Under normal a driving state, the oil pressure of the hydraulic chamber 6 is reduced so that the set load of the spring 7 becomes small, thereby preventing the valve from slopping and breaking.
    通常の運転状態では油圧室6の油圧を低下させるので、スプリング7のセット荷重が小さくなり、バルブの打音や破損が防止される。 - 特許庁
  • An earth wire and the conductive plug 25 are electrically connected to each other by bringing a spring-shaped terminal 30 provided on the tip of the earth wire into pressure-contact with the conductive plug 25.
    アース線の先端に設けたバネ状端子30を導電用プラグ25に圧接させることで、アース線と導電用プラグ25とを電気的に接続する。 - 特許庁
  • A pressure spring piece 325 for pushing the shield plate sections 512, 513 to the shield plate section 321 when inserting the shell 51 into the shell 31 is arranged on the shell 51.
    シェル51に、シェル31内にシェル51が挿入されたときシールド板部512,513をシールド板部321に押し付ける押圧ばね片325を設けた。 - 特許庁
  • When a predetermined gap is formed, the pressure member is allowed to fall and the slide piece main body is allowed to retreat by a predetermined distance by the elastic force of the coned disc spring.
    上記所定の空隙を形成するには、加圧部材を下降させ、皿ばねの弾撥力により摺動駒本体を所定距離だけ後退させる。 - 特許庁
  • A constant pressure supporting mechanism 19 which consists of a disc spring 28, a spherical bearing 24, a ring nut 26 and a fastening bolt 25, etc., is assembled on the first fulcrum part O1.
    第1支点部O_1 に、皿ばね28と球面軸受24とリングナット26と締め付けボルト25などからなる定圧支持機構19を組み付ける。 - 特許庁
  • A leaf spring 25 brought into pressure contact with the support pin 18 is mounted and fixed to the upper face of a mounting pedestal 24 of the base table 13 by a mounting screw 26.
    さらに、基台13の取付台座24の上面には支持ピン18に圧接される板バネ25が取付ネジ26で取付固定されている。 - 特許庁
  • To prevent the unintentional opening of a cover piece by gas pressure under the closed condition of the cover piece, by using a gas spring which helps assist an opening operating force of the cover piece.
    蓋体の開き操作力をアシストするためのガススプリングにおいて、蓋体の閉じ状態で蓋体のガス圧による自然開放を防止すること。 - 特許庁
  • To provide a gas-insulated switchgear which reduces size and cost by reducing a gas differential pressure compensating load, thereby reducing the number of spring load mechanisms.
    ガス差圧補償荷重を低減させることで、バネ荷重機構の個数を削減し、機器小形化とコストダウンを可能とするガス絶縁開閉装置を提供する。 - 特許庁
  • This clutch device comprises a clutch housing 51, an output side rotating body 52, a clutch part 53, a pressure plate 54, a diaphragm spring 55, and a supporting member 68.
    この装置は、クラッチハウジング51と、出力側回転体52と、クラッチ部53と、プレッシャプレート54と、ダイヤフラムスプリング55と、支持部材68と、を備えている。 - 特許庁
  • The axial movement of a detecting rod by a pressure is received by a metal spring and a light reflection board in the rear part of the detecting rod is arranged while facing a reflective photointerrupter.
    検出軸の押圧による軸方向移動を金属バネで受け、検出軸後部の光反射板を反射型フォトインタラプタと対向配設する。 - 特許庁
  • For the pressure contact device 62, a compression spring 64 is attached to one end of an oscillating member 66, and the cleaning brush 70 is attached to the other end of the oscillating member 66.
    圧接装置62には、揺動部材66の一端部に圧縮スプリング64が、揺動部材66の他端部にクリーニングブラシ70が取り付けられている。 - 特許庁
  • To provide a brush for electric machine where the quantity of abrasion is small and there is no peeling at a lamination part even if high spring pressure is applied to it and which is easy to manufacture and is inexpensive.
    高いバネ圧をかけても、摩耗量が少なく、積層部分での剥がれがなく、製造が容易で安価な電気機械用ブラシを提供する。 - 特許庁
  • To prevent local color displacement caused by unbalance of a spring pressure between four springs individually fixed to four corner parts of a frame holding a shadow mask.
    シャドウマスクを保持するフレームの4つのコーナー部にそれぞれ固定された4つのスプリングのバネ圧のアンバランスによって生じる局所的な色ずれを防止する。 - 特許庁
  • The dumper 10 includes as an essential constitution, a base 11, a filter 16, a leaf spring 17 and a flexible film 18 as a pressure absorbing film.
    ダンパ10は、主要な構成として基体11と、フィルタ16と、板ばね17と、圧力吸収膜としての可撓性フィルム18と、を含んでいる。 - 特許庁
  • The feed roller 215 and pinch roller 214 are normally brought in pressure contact with each other by a spring 221, and a document 223 is conveyed while being sandwiched within the nipping range between the feed roller and pinch roller.
    フィードローラ215とピンチローラ214はバネ221で通常は圧接しており、原稿223はこれらの間のニップ領域に挟まれて搬送される。 - 特許庁
  • To provide a paper feeding mechanism provided with a plate spring for pressing the paper sheets to an ejector member with the pressure-contact force without having influence to the design.
    設計の障害になることなく、取り出し部材に用紙を圧接力をもって圧接させることができる板バネを備えた給紙機構を提供すること。 - 特許庁
  • To provide a pressure opening and closing valve system to prevent generation of chattering due to a coil spring.
    本発明は圧力開閉バルブ装置に関し、コイルばねによるチャタリングの発生を防止した圧力開閉バルブ装置を提供することを目的とする。 - 特許庁
  • A pressure switching spring 670 laid over between the locking part 650a of the plate 650 and a supporting body 620 is elongated.
    圧力切替板650の係止部650aと、上記支持体620との間に架渡された上記圧力切替スプリング670が伸張される。 - 特許庁
  • The clutch device 100 comprises a clutch housing 1, an output-side rotating body 2, a clutch section 3, a pressure plate 4, a diaphragm spring 5, and a release member 6.
    クラッチ装置100は、クラッチハウジング1と、出力側回転体2と、クラッチ部3と、プレッシャプレート4と、ダイヤフラムスプリング5と、レリーズ部材6と、を備えている。 - 特許庁
  • This device comprises a clutch housing 1, an output-side rotor 2, a clutch portion 3, a pressure plate 4, a diaphragm spring 5, the release member 6, and a clip 7.
    この装置は、クラッチハウジング1と、出力側回転体2と、クラッチ部3と、プレッシャプレート4と、ダイヤフラムスプリング5と、レリーズ部材6と、クリップ7とを備えている。 - 特許庁
  • A movable pressure lid 11, which pressurizes the hydraulic oil filled in a reservoir room 10c by a spring 13, is provided each inside of the oil reservoirs 10.
    各オイルリザーバ10の内部には貯留室10cに充填した作動油をばね13により加圧する移動可能な加圧蓋11をそれぞれ設ける。 - 特許庁
  • On the other hand, when the gear-shifting will not occur, the hydraulic pressure becomes zero, and the piston 42 hits the bottom by the energizing force of the return spring 46.
    一方、変速が起こり得ない状態では、油圧は0にされ、リターンスプリング46の付勢力によってピストン42はどんつき状態となる。 - 特許庁
  • To provide a circuit breaker capable of enhancing a flow-limiting performance without adjusting a biasing force of a contact-pressure spring which returns a movable contact to a closed pole position.
    可動接触子を閉極位置に復帰させる接圧バネの付勢力を調整せずに、限流性能を高めることができる回路遮断器を提供する。 - 特許庁
  • Since the base circle part does not receive valve spring repulsion force at a time of lift, there is no concern of rise of surface pressure at a time of contact due to reduction of contact surface.
    ベースサークル部分は、リフト時のバルブスプリング反力を受けないので、接触面積の減少による接触時の面圧上昇の懸念はない。 - 特許庁
  • Even if the leaf spring portion slightly moves by the pressure upon operating the dial knob, the projection reliably interferes with the interference projection, thereby the sense of clicking is not degraded.
    ダイヤルノブの操作時の押圧によって板バネ部が僅かに移動しても、凸部と干渉突起とが確実に干渉するので、クリック感が損なわれることがない。 - 特許庁
  • The spool 3a is held in the second position against a spring 3b when the energizing force is generated by inputting the line pressure to the second input port (b).
    スプール3aは、第2入力ポートbにライン圧が入力することにより付勢力が生じ、スプリング3bに抗して第2位置に保持される。 - 特許庁
  • Since the rotated flow suppresses deviation of a valve element to suppress turbulence of the flow in the spring, the pressure control is stably performed.
    この回転流れにより弁体の偏心が抑制されてスプリング内流れの乱れが抑制されるため、圧力制御を安定して行えるようになる。 - 特許庁
  • A friction transmission member 89 interposed between the gear part 86a of the reel shaft 86 and a brake plate 88 is brought to a pressure contact state between them by a compression spring 90.
    リール軸86のギア部86aと制動板88との間に介装された摩擦伝達部材89が、圧縮コイルばね90によって圧接されている。 - 特許庁
  • A leaf spring 20A for pressure-bonding the side plates of the segments is provided between portions in which the other end-side flange portion 12 and the side plate of the other segment are engaged with each other.
    この他端側のフランジ部12と他方のセグメントの側板との係合部間に、セグメントの側板同士を圧着させる板バネ20Aを設ける。 - 特許庁
<前へ 1 2 .... 17 18 19 20 21 22 23 24 25 .... 44 45 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.