A control part 21 operates a driving part 22 on the basis of the detected result of the vibration sensor 31 and moves a stopper 23 from the position of maintaining the state that a spring 25 is shrunk to the position of releasing the spring 25. 制御部21は、震動センサ31の検出結果に基づいて、駆動部22を動作させ、スプリング25が縮んだ状態を維持させる位置からスプリング25を解放する位置へストッパ23を移動させる。 - 特許庁
When the gas pressure becomes low (weak heating power), the rubber film 62 is deformed (weak heating power position) in the reverse direction (the left in the figure) of the case where the gas pressure is high by the spring properties of the rubber film 62 per se and the force of a pressure regulating spring 67. ガス圧が低く(火力弱)になると、ゴム膜62は、ゴム膜62自体のバネ性及び調圧バネ67の力により、ガス圧が高いときと逆方向(図面左方向)に変形する(火力弱位置)。 - 特許庁
A cross sectional shape in the horizontal face of these slits 522b, 523b is made to have nearly triangular shape, and the movable spring is pinched by inserting the movable spring which is a plate shaped elastic body into the slits 522b, 523b. このスリット522b,523bの水平面における断面形状を略三角形状とし、板状の弾性体である可動バネをスリット522b,523bに挿入することによって、可動バネを挟持する。 - 特許庁
Consequently, the acceleration of the movable body is not alleviated much by the first spring 17 till the valve body sits on the seat surface and the acceleration is greatly alleviated by the first spring 17 after the valve body sits on the seat surface. これにより、可動子は、弁体が座面に着座するまで、第1バネ17によって加速がさほど緩和されず、弁体が座面に着座した後に、第1バネ17によって加速が大きく緩和される。 - 特許庁
The probe 2C is mounted at such a position as being displaced according to the vibration of the vertical spring 2A and as allowing the vibration part to excite the vibration of the rotary spring 2B by a change in the interatomic force based on the displacement. 探針2Cは、縦バネ2Aの振動に伴って変位する位置であって、且つ、当該変位に基づく原子間力の変化により回転バネ2Bの振動を振動部に励起させる位置に付設される。 - 特許庁
By rotating the bridge portion supporting member 4 in a clockwise direction, an overlapping part (mark A) between an extending part 4c and the bridge portion 5c is increased, so that a spring constant of the upper leaf spring 5 is apparently increased. 架橋部支持部材4を時計回り方向に回動してゆくと延出部4cと架橋部5cとが重なり合っている部分(符号A)が増加し、見かけ上、上部板バネ5のバネ定数を増加させることができる。 - 特許庁
The dancer roller 35 is energized by a compression spring 39 towards the left of Figure, and tension is given to the tape-shaped coated optical fiber trained over the dancer roller so as to be balanced with the compressive force of the compression spring. ダンサーローラ35は、圧縮バネ39により図の左方に向けて付勢されており、圧縮バネの圧縮力に釣り合うようにダンサーローラに掛け渡されたテープ状光ファイバ心線に張力が付与される。 - 特許庁
When the temperature drops to lower than the preset temperature, the deforming force of the temperature sensor 16 becomes smaller than the elastic force of the leaf spring 13, and the leaf spring 13 returns downward due to its own elastic force, therefore the contact 14 also comes down. 設定温度よりも低くなると、温度センサー16の変形力の方が板バネ13の弾性力よりも小さくなり、板バネ13は自らの弾性力で下方に戻り、接点14も下方に下がる。 - 特許庁
The drive mechanism 1 has a compression spring 13 for energizing the thrust ball 11, and a thrust rod 14 for thrusting the thrust ball 11 against the compression spring 13 to cancel the engagement of the engaging ball 9 with the driving wheel 5. 駆動装置1は、押圧ボール11を付勢する圧縮ばね13と、圧縮ばね13に抗して押圧ボール11を押圧して係合ボール9と駆動輪5との係合を解除する押圧棒14とを備えている。 - 特許庁
To provide a working tool hang-down device such as a spring balancer capable of preventing a working tool from falling off by restricting rotation of a drum using a simple constitution even if an energizing spring is broken. スプリングバランサーなどの作業工具吊り下げ装置において、簡単な構成で、万が一付勢バネが折損した場合であっても、ドラムの回転を規制することによって作業工具が落下するのを防止可能とすること。 - 特許庁
Because the spring contact piece 38 has a sufficient spring length and has a hole 48 at a position in contact with an opposed pin, the prescribed holding force can be obtained even when a post of a small sectional dimension is accepted. ばね接触片38は、十分なばね長を有すると共に、相手ピンと接触する位置に孔48を有するので、より小さい断面寸法のポストを受容した場合であっても所定の保持力が得られる。 - 特許庁
The sleeve is fixed to the lower end part of the pressure shaft 24, and further, the pressure shaft is vertically movably held in a state of being passed through a holding plate 26, and is energized toward the workpiece by a pressure spring (compression coil spring) 28. スリーブは加圧シャフト24の下端部に固定されると共に、加圧シャフトは保持プレート26を貫通した状態で上下動可能に保持され、加圧バネ(圧縮コイルバネ)28によりワークへ向けて付勢されている。 - 特許庁
A discharge amount suppressing mechanism 8 such as an orifice is interposed in a carbonated spring discharge pipe 406 and thus the state of storing the carbonated spring at a prescribed water level at the bottom of the pressure container 1 is maintained. 炭酸泉排出管406にはオリフィスなどの排出量抑制機構8が介装されており、これにより圧力容器1の底には所定水位の炭酸泉が貯留された状態が維持される。 - 特許庁
Further, a supporting point part 36c and a spring 14 are provided under the actuator base 30, with these components the actuator base 30 is supported on the frame 15, and an adjusting screw 35b is provided to elongate and contract the spring 14. また、アクチュエータベース30の下面に支点軸部36cと、ばね14を設け、これらを介してフレーム15にアクチュエータベース30を支持させるとともに、ばね14を伸縮させるための調節ねじ35bを設けた。 - 特許庁
To provide a lower surface plate to be used for an air spring having excellent durability, the lower surface plate improving wear of a flexible member due to sliding with a rubber seat, and to provide a method for manufacturing the plate and an air spring with improved durability. ゴム座部との摺動による可とう性部材の摩耗を改善し、耐久性に優れた空気ばねに使用する下面板及びその製造方法並びに耐久性が改善された空気ばねを提供する。 - 特許庁
A position, in which the spring 4 is mounted on the storage box 1, is made variable so as to vary a compression quantity of the spring 4 in a state in which the opening 1a of the storage box 1 is closed with the floor cover 3. 収納ボックス1の開口1aを床蓋3が閉塞した状態での伸縮自在バネ4の圧縮量を変化させるように上記伸縮自在バネ4の収納ボックス1への取付位置を可変とする。 - 特許庁
By laminating the armature 12 and the plate spring 13 on a side face of the hub 11 and deforming the deforming parts 11e of the hub 11, the fixing parts 13a of the plate spring 13 are fixed to the guide parts 11d of the hub 11. ハブ11の側面に、アーマチュア12と板ばね13を重ねて、ハブ11の被変形部11eを変形させることにより、板ばね13の固定部13aをハブ11のガイド部11dに固定した。 - 特許庁
In a socket contact, comprising a cylindrical body and an elastic body which is arranged inside of the cylindrical body, the cylindrical body is formed of a material which does not need a spring, while the elastic body is fomred of a material which needs a spring. 筒形の本体部と、この本体部内に設けられた弾性体からなるソケットコンタクトであって、本体部はバネ性を必要としない材料で形成し、弾性体はバネ性を必要とする材料で形成する。 - 特許庁
A maximum spring load (F100) given to the swash plate 16 by an inclination reduction spring 17 at maximum delivery capacity time is determined by the following formula F100(N)=(180±30)-4×(VD-120) (where, VD: compressor displacement (CC)). また、最大吐出容量時における傾角減少バネ17が斜板16に与える最大バネ荷重(F_100)は、次式 F_100(N)=(180±30)−4×(V_D−120)(ここで、V_D :圧縮機排気量(CC)) によって定められる。 - 特許庁
To provide a spring forming machine with which in the case of rotating a wire rod feeding unit for feeding the wire rod around the shaft of a quill, the development of strain in the wire rod, is avoided, and the spring having good precision can be formed. 線材を送出する線材送りユニットをクイルの軸回りに回転させたときに、線材に歪みが生じることを回避し、精度の良いばねを製造することができるばね製造機を提供する。 - 特許庁
The main contact device 2A is provided with a main fixed contact 27 fixed to a unit body 1 and a main contact spring 23 made of a leaf spring to which a main movable contact 25 coming in and out of contact with the main contact 27 is firmly fixed. 主接点装置2Aは、器体1に固定された主固定接点27と、板ばねからなり主固定接点27と離接する主可動接点25が固着された主接点ばね23とを備える。 - 特許庁
The lamp pin connecting part 6 is formed by arranging two plate springs capable of interposing a lamp pin 13, and the quick connecting terminal part 7 is formed in a spring type by arranging a plane part receiving an electric wire 11 and a locking spring. また、ランプピン接続部6はランプピン13を挟持可能な2枚の板ばね20aを配置し、速結端子部7は電線11を受ける平面部21aと鎖錠ばね21bを配置したスプリング式とした。 - 特許庁
Besides, the leaf spring bending portion 11 and the blade bodies 13 are provided with retaining engagement portions 15a 15c for preventing the leaf spring bending portion 11 and the blade bodies 13 from coming off the grip portions 14. また、板ばね屈曲部11と刀身部13には、これら板ばね屈曲部11と刀身部13とが握り部14から抜け出さないようにするための抜止め係合部15a、15cが設けられている。 - 特許庁
One through hole 421 is formed in the radial direction of the columnar set component 42, one compression spring 451 is inserted into the through hole 421, and a ball 452 is installed at each of both ends of the spring 451. 円柱形セット部品42の径方向上に1個の貫通孔421があり、1個の圧縮スプリング451を貫通孔421の中に入れ、かつスプリング451の両端にそれぞれボール452を設置する。 - 特許庁
The hair clipper has a movable blade 13 arranged on a fixed blade 12, a pressing spring 16 which presses the movable blade 13 to the fixed blade 12, and a change lever 17 which supports the pressing spring 16 and is pivoted by a fixed plate 14. バリカンは、固定刃12上に配置された可動刃13と、可動刃13を固定刃12に押付する押付ばね16と、押付ばね16を支持し固定板14に軸支された切替レバー17を有している。 - 特許庁
If a spring 15 with an appropriate spring constant is selected, and a stopper 10 is set to come into contact with a stopper rest part 11 within a range of a maximum allowable added pressure of a heat insulating material, the heat insulating material 3 can be prevented from damage. 適切なばね定数を持つばね15を選択し、断熱材の最大許容付加圧力の範囲内でストッパ10がストッパ受け部11に当接するように設定すれば、断熱材3の破損を防止することができる。 - 特許庁
Each of the spring members 6 is made of same type and is bent in S shape along the lamination face of the unit cell 21 at the center part in lamination direction of the unit cell 21 so that it develops spring performance. それぞれのバネ部材6は、同じ種類のものであり、単セル21の積層方向の中央部において、単セル21の積層面に沿うようにS字状に折り曲げられて、ばね性が発揮されるようになっている。 - 特許庁
A spring member 65 is incorporated in an engagement oil chamber 63 of the forward clutch 48, and the forward clutch 48 is held in a slipping state or an engaged state by spring force even during an idling stop in which a control oil pressure is reduced. この前進クラッチ48の締結油室63にはバネ部材65が組み込まれ、制御油圧が低下するアイドリングストップ時にも前進クラッチ48はバネ力によって滑り状態または締結状態に保持される。 - 特許庁
The spring power of a switch spring 11 is given to a retainer 9 holding an engagement element 8 and the retainer 9 is retained elastically in the neutral position where the engagement element 8 is disengaged to the cylinder face 6 and the cam face 7. 係合子8を保持する保持器9にスイッチばね11のばね力を付与して係合子8が円筒面6およびカム面7に係合解除された中立位置に保持器9を弾性保持する。 - 特許庁
The heavy duty relay 1 has a change-over spring 3 which can be elastically deflected by switching force C, and a normally open contact 6 on which the contact 5 of the change-over spring 3 is pressed at a switching position in a conductive state. ヘビーデューティリレー1は、切換え力Cにより弾性的に撓むことができる転換ばね3と、転換ばね3の接点5が切換え位置で導電状態で押圧される常開コンタクト6とを有する。 - 特許庁
A leaf spring structural part 3 which supports the optical component 4 is supported in the form of a cantilever on the upper face of the base body 2, and a pair of slide parts 5 are provided at both sides in the width direction of the leaf spring structural pat 3. 基体2の上面には、光学部品4を支持する板ばね構造部3が片持ち梁状に支持されるとともに、一対のスライド部5が、板ばね構造部3の幅方向両側方に設けられている。 - 特許庁
This valve device includes a return spring 38 developing spring force pressing a valve element 31 to a valve closing direction by allowing a free end part 39a to be in slide contact with a sliding contact surface provided on the rear surface of the valve element 31 opening/closing a valve hole 12. 弁穴12を開閉する弁体31の裏面に設けた摺接面に対し自由端部39aを摺接させて、弁体31を閉弁方向に付勢するバネ力を発生するリターンスプリング38を備える。 - 特許庁
The tongue piece 21 is provided with a property of spring, that is, elasticity, by bending, and the contact pressure is acted on the male terminal by the repulsion of a spring part 30 (the restoring force on the basis of the elasticity). また、舌片21は、曲げ加工によってバネとしての性質すなわちバネ性を付与されており、バネ部分30の反発力(弾性に基づく復元力)によって雄端子に接触圧力を作用させる。 - 特許庁
The tail gate stabilizer comprises a spring standing against a load applied on the tail gate; a material stop, having flexibility and providing a counter balance with a stop device; and a protection housing to cover the spring and the material strap having flexibility. テールゲートに加えられる荷重に対抗するばねと、カウンタバランスに停止装置を提供する可撓性のある材料ストラップと、ばね及び可撓性のある材料ストラップをカバーする保護ハウジングと、から構成される。 - 特許庁
A coil spring 30 is extended between the upper surface of the valve 24 and an inside fixed point 28 of the intake pipe 12, the valve 24 is approximately vertically erected by force of the coil spring, and an opening of a lower leader 10b is maintained in an opening state. 弁24の上面と取水管12の内面固定点28の間にコイルばね30を延設し、このばねの力で弁24をほぼ垂直に立て、下部縦樋10bの口を開いた状態に保つ。 - 特許庁
As noted above, since a valve lift amount to decide the allowable number NEG of revolutions togetherwith the spring load and a valve mass of a valve spring is detected, the accurate allowable number NEG of revolutions is set at a step S1030. このようにバルブスプリングのバネ荷重やバルブ質量等と共に許容回転数NEGを決定づけるバルブリフト量が判明するので、正確な許容回転数NEGを設定することができる(S1030)。 - 特許庁
A front end portion 30A of the gusset 30 extends from a front end portion of the arranging position of the spring support 14, namely from an upper surface 10B of the front side member 10 in a side of a front wall portion of the spring support 14 to the cowl side. また、ガセット30の前端部30Aが、スプリングサポート14の配設位置の前端部、即ち、スプリングサポート14の前壁部14Aの側方におけるフロントサイドメンバ10の上面10Bからカウルサイドに延びている。 - 特許庁
A coil spring 53 is positioned between the pulleys 43 and 45 and tension is given to the wires 21 and 23 by urging the pulleys 43 and 45, so that the pulleys 43 and 45 is energized so as to rotate in the containing direction of the spring 53. 上段及び下段駆動プーリ43,45間にコイルスプリングを配設し、両駆動プーリ43,45を、コイルスプリング53が縮まる方向へ回動するように付勢して各金属ワイヤ21,23に張力を与える。 - 特許庁
Then, a female screw part 22a is disengaged from the male screw part 21, the moving member 22 is set to a position of a right side limit and the female screw part 22a is energized in a direction engaging with the male screw part 21 by spring force of a leaf spring 23. このとき、雌ねじ部22aが雄ねじ部21から外れ、移動部材22は右限位置に設定されるとともに、板ばね23のばね力で雌ねじ部22aが雄ねじ部21に螺合する方向に付勢される。 - 特許庁
A coil spring 26 which has, up and down, disks 24 and 22 made of a thin-plate steel material and serving as a compression spring is arranged between the lower end of the retainer 16 and the lower end 14-2 of the filter cloth 14 and stretches the filter cloth 14 under a specified load. リテーナ16の下端と濾布14の下端14-2との間に、上下に薄板鋼材製円板24, 22を備えた圧縮ばねとしてのコイルスプリング26が配置され、濾布を所定荷重にて緊張している。 - 特許庁
The bellows member 28 is disposed at the outer periphery of the coil spring 24, clamped by the large diameter part 22a and the butt member 26 and thus fixed at a position at which it can surround the outer periphery of the coil spring 24. 蛇腹部材28は、コイルスプリング24の外周に配設されるとともに太径部22aと突き当て部材26とに挟まれることによりコイルスプリング24の外周を包囲可能な位置に固定されている。 - 特許庁
To provide a leaf switch where the spring characteristic is well maintained and does not settle easily even when made small, spacing between contact points of both spring plates can be always installed in normal positions and where the operation of the pressing member is carried out smoothly. たとえ小型化してもバネ性を良好に保て、へたりにくく、両板バネの接点部間の間隔を常に正規の位置に設置でき、さらに押圧部材のスムーズな動作が行なえるリーフスイッチを提供すること。 - 特許庁
A body 1 and a display cylinder 6 are connected by a coil spring 5, the coil spring 5 is extended by the weight of the ink tank, and a position corresponding to the weight of the display member 4b is shown in a window hole 6b when the display cylinder is gripped. 本体1と表示筒6とをコイルスプリング5にて連結し、表示筒を把持したときに、インキタンクの重みでコイルスプリング5が伸び重みに見合った位置を窓孔6bに指示部材4bが表示される。 - 特許庁
Furthermore, this invention also includes the spring steel wire which can be obtained by skinpass-elongation wiring the spring steel after applying the quenching thereto without applying the tempering thereto, and whose tensile strength is not lower than 1,900 MPa and whose strength ratio is not lower than 0.90. また前記ばね用鋼を、焼入れした後、焼戻しをすることなく、スキンパス伸線して得られ、引張強さが1900MPa以上、耐力比が0.90以上であるばね用鋼線も本発明に包含される。 - 特許庁
The spring hinge 1 has a pair of blades 11, 12, a shaft 16, and a coil spring 17 energizing the blade 11 in a clockwise direction and energizing the blade 12 in a counterclockwise direction in a state of being wound around the shaft 16. スプリング蝶番1が一対の羽根11,12と、シャフト16と、シャフト16に巻回された状態にあって羽根11を時計方向に付勢し、羽根12を反時計方向に付勢するコイルスプリング17とを有する。 - 特許庁
The supporting apparatus has at least one leaf spring type bent member disposed tangentially to the optical member and has at least one leaf spring type bent member disposed in the radial direction with respect to the optical member. この支持装置は、光学部材に正接を成すように配置された、板ばね状の少なくとも1つの曲げ部材と、光学部材に対して径方向に配置された、板ばね状の少なくとも1つの曲げ部材とを有する。 - 特許庁
To provide a suspension system of a vehicle equipped with a variable spring constant, capable of precluding generation of rolling in good performance while the occurrence that the vehicle body inclines due to a change of the spring constant is avoided as much as practicable. ばね定数の変更が可能な車両懸架システムにおいて、ばね定数の変更により車体が傾いた状態となることを極力回避しつつ、ローリングの発生も良好に防止することを可能にする。 - 特許庁
Both end parts of a coil spring 7 are respectively connected to the pulley (an outside ring body) 2 and a rotor shaft (an inner ring body) 3 and vibration of the coil spring 7 is damped by frictional resistance of a flange part (ring-shape member) 15 and a friction plate 8. コイルばね7の両端部をプーリ(外側環体)2とロータ軸(内側環体)3それぞれに連結し、コイルばね7の振動を鍔部(環状部材)15と摩擦板8との摩擦抵抗で減衰させる構成。 - 特許庁
More specifically, the crest 1a of the rotor can be recessed into the rotor 1 as pressure is added outward of the rotor 1 by means of a spring mechanism formed of a plate spring S1. 具体的には、板バネS1によって形成されるバネ機構により、ロータ1の山部1aを、同ロータ1外側へ向けての圧力が加えられたまま、同ロータ1内への没入を可能とされた状態にする。 - 特許庁
The plane shape of a setting lever jumper 23 is arranged in the upper part of a yoke return spring 5a and a projection 5c is formed near the tip end of the yoke return spring 5a in a shape embedding the two cross sectional gaps. 裏押さえ23の平面形状がカンヌキ戻しバネ5aの上部に配設され、この2つの断面隙間を埋めるような形状でカンヌキ戻しバネ部5aの先端付近に突形状5cが形成されている。 - 特許庁