As a result, the assembling operation of the piston guide C_2 and the stem C_3 and the following assembling operation of the annular piston C_1 and a coil spring are precisely and easily carried out. これにより、ピストンガイドC_2とステムC_3の組み付け操作及びそれに伴う環状ピストンC_1及びコイルスプリングの組み付け操作が正確に且つ容易に行える。 - 特許庁
When the still image recording button 8 is depressed to push down the projection 11, the lever 17 rotates by engagement with a pawl 21 against the biasing force of the spring 19. 静止画記録釦8が押されて突出片11が下がると、ツメ21との係合によりレバー17がばね19の付勢力に抗して回転する。 - 特許庁
To achieve reduction of size without narrowing the movable range in a supporting device adapted to support a backrest of a chair by utilizing a link mechanism or a gas spring. リンク機構およびガススプリングを利用して、椅子の背もたれ等を支持する支持装置において、可動範囲を狭くすることなく小型化を達成する。 - 特許庁
The directional control valve (8) is furnished with a main spool (11A) and a control spool (11B) divided into two and the control spool (11B) abuts the main spool (11A) through a spring (10). 方向制御弁(8)には2分割された主スプール(11A)と制御スプール(11B)が内装され、制御スプール(11B)はバネ(10)により主スプール(11A)に当接している。 - 特許庁
The tape unloading operation is completed in the state, when the drive cam plate is moved relatively with respect to the cam plate with respect to the extension of the extensions coil spring. テープアンローディング動作は、引っ張りコイルばねの伸びを伴ってドライブカムプレートがカムプレートに対して相対的に移動された状態で完了する。 - 特許庁
To reduce noise due to pressure pulsation in a solenoid valve in which a coil spring is held between a shaft having a valve element and a seat having a valve seat. 弁体を有するシャフトと弁座を有するシートとの間にコイルスプリングを挟持した電磁弁において、圧力脈動による異音を低減する。 - 特許庁
To provide a lamp socket capable of maintaining a positional relation with a lamp pin, even if a conductive spring formed of a self-retaining bimetal is reversed and displaced. 自己保持型バイメタルで形成された導電ばねが反転変位してもランプピンとの位置関係を保つことができるランプソケットを供給することにある。 - 特許庁
In locked state, the rollers are fitted to the narrower sides of the operating chambers by the action of a spring 26 through an operating plate 18 and the projected piece thereof. これらローラは、ロッキング状態において、作動プレート18とその突出片とを介して、スプリング26の作用により作動室の狭い側に嵌り込む。 - 特許庁
The early current is set so that the brake shoe resists to the energizing force of the return spring and is set to the magnitude enlargingly opening to the position a proper gap is obtained between brake drums. 早期電流は、ブレーキシューがリターンスプリングの付勢力に抗し、ブレーキドラムとの間に適切な隙間を得る位置まで拡開する大きさに設定する。 - 特許庁
A compression coil spring 17 is provided for absorbing impact force caused in a meshing part of the worm 12 and the worm wheel 30 when the clamp lever clamps the work. クランプレバー32がワークをクランプしたとき、ウォーム12とウォームホイール30との噛合部に生じる衝撃力を吸収する圧縮コイルバネ17を設ける。 - 特許庁
Each of the sidewalls 12 of the neck portion 18 is provided with a transversely-stretchable bias member 22 that is formed of stiff but flexible, spring-like plastic material. ネック部分18の側壁12は、硬いが可撓性のスプリングのようなプラスチック材料で形成された横方向に伸びるバイアス部材22を備えている。 - 特許庁
The conventional temporary panel is incorporated with a key keeping device operated by a variable setting password system electric lock mainly composed of an operation switch, a solenoid and a spring. 従来の仮設盤に、主として、操作スイッチ、ソレノイド、バネからなる、設定可変の暗証番号方式の電気錠で作動する鍵保管装置を内蔵した。 - 特許庁
When the driving-side rotating body 30 is rotated, the coil spring 32 is shrunk inward, and the rotation is transmitted by the clutch 20 to the driven-side rotating body 29. クラッチ20は、駆動側回転体30が回転すると、コイルスプリング32が内側に縮むので、その回転を従動側回転体29に伝達する。 - 特許庁
The damping section 4 is provided with a coil spring 22 to connect the flexible plate 2 and the hub flange 3 in the peripheral direction, and a viscosity resistance generating section 25. 減衰部4は、フレキシブルプレート2とハブフランジ3とを円周方向に連結するコイルスプリング22と、粘性抵抗発生部25とを備えている。 - 特許庁
A pressing plate 255 is made to be shifted toward the cassette 1 which is set in the cassette housing 231 with setting an end 256 as a pivot core with a spring 257. 押さえ板255は、バネ257により端部256を回動中心として、カセット収納部231にセットされたカセット1へ向かって付勢されている。 - 特許庁
In this inserted state, the clamp lever 24 is put in the clamp position to strongly pressure-fit the mounting bracket 41 to the base 21 by the plate spring member 25. この挿入状態でクランプレバー24をクランプ位置とすることにより、取付ブラケット部41が、板ばね部材25を介して基板部21に強く圧着される。 - 特許庁
When the shadow mask 7 is heated up and the frame 8 is return-deformed, the spring mounting member 21 moves the shadow mask 7 to the screen side. 動作開始直後にシャドウマスク7が加熱されてフレーム8が戻り変形すると、スプリング取付部材21がシャドウマスク7をスクリーン側に移動させる。 - 特許庁
Then, when the spring piece 24 is pressingly expanded outward by the lever action of the extraction tool T, a first locking projection 27 is disengaged from the locking projection 12. 続いて、抜き治具Tのてこ作用によって、弾発片24を外側に押し広げると、第1の係止突起27は第2の係止突起12から外れる。 - 特許庁
A pad spring 10 located on the turn-in side of a disc has a guide plate part 14, a radial energization part 16 and a rotating energization part 19. ディスクの回入側に位置するパッドスプリング10には、案内板部14、径方向付勢部16と共に回転方向付勢部19を設ける。 - 特許庁
In the other enforcement example, the return spring is provided between the tongue pieces while facing the tongue pieces of two outer discs facing to the piston and pressure receive surface in the axial direction. 他の実施例ではピストン及び受圧面に対面する2枚のアウタディスクの舌片を軸線方向で対向させ、該舌片間にリターンばねを設けた。 - 特許庁
The tilt angle θ of the pinion is set so that the retreating force F acting on the pinion becomes smaller than the reaction force Sp of the pinion spring 20. そこで、ピニオンスプリング20の反力Spより、ピニオン6に働く後退力Fの方が小さくなる様に、ピニオンの傾き角度θが設定されている。 - 特許庁
When the relay is put into an open state, the contact opening element (20) strikes the movable spring contact just before the magnet system completely opens, so that the welding is torn off. リレーを開状態にする際、コンタクト開離要素(20)は、磁石システムが完全に開く直前に可動ばねコンタクトを叩くので、溶着が引き裂かれる。 - 特許庁
An ultrasonic wave transducer 38 and a target 42 for calibration are disposed in relatively fixed positions in an air chamber 26 of an air spring 10. エアスプリング10のエアチャンバ26内に、超音波の送受波器38と校正用ターゲット42を、互いに相対的に固定された位置に配置する。 - 特許庁
To provide a bracket which generates high closing strength to fit an arch wire to a bracket slot without increasing danger of spring damage at time of opening. 開く際のばね損傷の危険を増大させることなく、アーチワイヤをブラケットスロットに固定するための高い閉じ力を発生するブラケットを提供する。 - 特許庁
Two or more steps are formed at other parts on a leaf spring 12, one constituent component of a rotary encoder 1, than a motor mounting part 12a and a housing mounting part 12b. ロータリエンコ−ダ1の構成部品である板バネ12に2箇所以上の段差部を、モータ取付け部12aおよびハウジング取付け部12b以外に設ける。 - 特許庁
The heat source water such as plant waste water and hot spring water is made to flow in the auxiliary heat exchanger (9), so as to supercool the refrigerant and heat the heat source water. 工場排水、温泉水等の熱源水を補助熱交換器(9)に通水して、冷媒を過冷却すると共に熱源水を昇温させる。 - 特許庁
The car support 18 is provided with a frame 19 fitted to the cage 50 side and a rubber stopper 20 retained to the frame 19 via a spring 23. かご支え18はかご室50側に取り付けられたフレーム19と、フレーム19にスプリング23を介して保持されたゴムストッパー20とを有している。 - 特許庁
Force necessary for opening the intake and exhaust valve is accumulated as elastic energy in a valve opening spring by using a small fluid driving source to fill operating oil. 吸排気弁の開弁に必要な力を小さな流体駆動源を使用して作動油の充填によって開弁バネに弾性エネルギとして蓄積させる。 - 特許庁
The drive wheel 11 and the electric motor 12 are supported by a motor base 18, and the motor base 18 is connected with an elevating actuator 13 via a compression coil spring 23. 駆動輪11と電動モータ12はモータベース18に支持され、モータベース18は圧縮コイルスプリング23を介して昇降アクチュエータ13と接続される。 - 特許庁
A lift handle operably connected to a spring type plunger respectively is used for adjusting the fallable type guide/restraint device between the three positions. ばね式プランジャにそれぞれ動作可能に連結されたリフトハンドルが、可倒型案内/拘束装置を3つの位置の間で調節するために使用される。 - 特許庁
Moreover, a tension spring 32 applying compression force on a pivot shaft 26 and the tube is attached on a pressing element 20 at a position gripping the tube at compression position. さらに、チューブの圧縮位置を挟む位置にて押圧子20に、枢動軸26及びチューブに圧縮力を与える引張りばね32を取付ける。 - 特許庁
A groove 40 in which one leg piece 50 of the torsional spring 5 fits is formed at a point located on the outer side of the bearing section 11 on the central shaft 4 of rotational movement. 回動中心軸4上にて軸受け部11の外側に位置する箇所には、ネジリバネ5の一方の脚片50が嵌まる溝40が形成されている。 - 特許庁
A safety pin has a spherical body (3) threaded and fixed in the immediate vicinity of a spring part (2) at the root of a needle part of the main body of the safety pin (1). 安全ピン本体(1)の針部の根元、スプリング部(2)のすぐ近くに球状体(3)を挿通固定してなる安全ピンであることを特徴とする。 - 特許庁
Even in a case where the suppressor 23 is not locked in a closed state, the suppressor 23 is kept pushed in the direction of closing by the energy-applying force of a torsion spring 39. またサプレッサ23を閉じた状態でロックしない場合でも、トウションバネ39の付勢力によりサプレッサ23は閉じる方向に付勢される。 - 特許庁
In a state that a slider 30 is retained in the return position, a moving plate 50 is moved toward the initial position by an elasticity restoring force of the return spring 40. スライダ30が復帰位置に保持された状態では、復帰バネ40の弾性復元力によりムービングプレート50は初期位置に移動している。 - 特許庁
Also, a back plate 3 for fixing one end of the plate spring 2 with a screw 4 is provided, and the back plate 3 is moved to adjust the attractive force. また、板バネ2の片端をネジ4で固定するための座板3を設け、その座板3を移動させて吸着力を調整できるようにする。 - 特許庁
An adjusting screw 307, a first projected part 308 and an elastic members such as a leaf spring 300 are attached on both sides of an optical component such as a mirror MI. 調整ビス307、第1突起部308、及び板バネ300等の弾性部材をミラーMI等の光学部品の両端に取り付ける。 - 特許庁
A drum earth 119 passes through the center of the drum flange 36 movably in the axial direction and fixed to the earth plate 118 of a conductive flat spring. ドラムフランジ36の中心に軸方向移動可能にドラムアース119が貫通し、導電性の板ばねであるアース板118に固定されている。 - 特許庁
The bearing 11 is conductive and a bias voltage is applied from a power source 2 to the transfer roller 1 through the bearing 11 and spring 12. 軸受11は導電性を有しており、軸受11とバネ12を介して、電源2から転写ローラ1にバイアス電圧が印加されるようになっている。 - 特許庁
Consequently, unevenness of dimension of a main spring part 12a of the rubber elastic body 12 formed between the plate member 15 and a mounting member 11 is reduced. これにより、板部材15と取付部材11との間に形成されるゴム弾性体12の主バネ部12aの寸法のばらつきを小さくすることができる。 - 特許庁
Moreover, the vibration electrode 106 bridged with the supporting member 105 functioning as a spring can be deviated (vibrated) in the direction toward the fixed electrode 104. また、バネとして機能する支持梁105により張架されている振動電極部106は、固定電極部104の方向に変位(振動)可能とされている。 - 特許庁
When the contact is opened, the leading component 13 moves up by the urging force of the spring 14 to unfailingly cut off the movable contact 8 from a fixed contact 10. 接点開放時には、引外し部材13がスプリング14の付勢力で上昇し、可動接点8を固定接点10から確実に引き外す。 - 特許庁
Since the pitch of the helical portion 32 of the spring material 3 is increased or decreased, the helical portion 32 can catch and kill an insect B1 for mechanical insecticide. ばね材3の螺旋部32のピッチが増減されるので、螺旋部32で虫B1を挟んで捕殺することができ、機械的に殺虫することができる。 - 特許庁
When the interference of the end face lip portion 28 is reduced, the end face lip portion 28 is slid with the operation of the spring means 29 to compensate for the reduced interference. 端面リップ部28のしめしろが低下するとバネ手段29の作用により端面リップ部28がスライドし、低下した分のしめしろを補うことができる。 - 特許庁
The torsion coil spring 20 having stretching force in a torsional direction is provided with a first and a second coil parts 21 and 22 and a first to a third straight line parts 23, 24 and 25. 捩り方向に伸縮力を有する捩りコイルバネ20に、第1及び第2コイル部21,22と、第1乃至第3直線部23,24,25とを設ける。 - 特許庁
To materialize a method for manufacturing a retainer ring of a structure getting in parallel with a tapered surface and receiving contact pressure on wide area at an end part of a air spring. 空気ばねの端部において、テーパ面と平行になって面圧力を広い面積で受ける構造の保持リングの製造方法を実現する。 - 特許庁
The lid of a CATV apparatus has a coil spring on the back of a lid short-circuiting member for serving for pressing the short-circuiting member to an input side terminal and an output side terminal. 蓋の短絡材の裏側に入力側端子及び出力側端子へ短絡材の押付けを助勢するコイルスプリングを備えたCATV機器の蓋。 - 特許庁
To provide an inexpensive coil spring for suppressing abnormal noises by damping vibration, without increasing the number of components and manufacturing man-hours. 部品点数および製造工数を増加することなく、振動を減衰して異音の発生を抑制することのできる安価なコイルスプリングを提供する。 - 特許庁
In a lower shielding plate 2, a plate spring part 21 formed by folding an end part upward elastically abuts against a lower end part of each LED 333. 下シールド板2では、端部を上方に折り曲げた板ばね部21がLED333の各々の下端部に対して弾性をもって当接している。 - 特許庁
Thus, the rear side door hinge part 84 does not become a linear shape but becomes a sheet shape, and easily unfolds, and restrains spring back of a door rear part after unfolding. 従って、後側ドアヒンジ部84は線状ではなく面状になり、展開しやすくなる共に展開後のドア後部のスプリングバックも抑制される。 - 特許庁