When voltage conversion operation is started, a control circuit 30 computes a voltage command value for each time of control, taking a target voltage computed from a torque command value TR and a motor rotation number MRN as the final value, and controls a step-up converter 12 so that the output voltage Vm agrees with the voltage command value. 制御回路30は、電圧変換動作を開始すると、トルク指令値TRおよびモータ回転数MRNから演算した目標電圧を最終値として制御タイミングごとの電圧指令値を演算し、出力電圧Vmが電圧指令値と一致するように昇圧コンバータ12を制御する。 - 特許庁
At transient time in which the intake air flow is smaller than the target air flow by more than predetermined volume, fuel is finely atomized to improve a fuel consumption rate by increasing discharge pressure of a high pressure pump to increase a fuel injection pressure of a fuel injection valve, whereby increase of black smoke in exhaust gas is prevented. そして、吸入空気量が目標空気量より所定量以上不足する過渡時の場合、 高圧ポンプの吐出圧を増加させ燃料噴射弁の燃料噴射圧力を増加させることにより、燃料噴霧を微粒化し燃料消費率を向上するとともに、排気ガス中における黒煙の増加を防止する。 - 特許庁
At the time of inputting the character information existing in the application data storage part 203, the application data storage part 203 is retrieved based on the character information inputted by a keyboard, and application data belonging to the group to which the retrieved application data are belonging are called, and the target application data are selected so that character input can be operated. アプリケーションデータ格納部内に存在する文字情報を入力する際、キーボードから入力された文字情報をもとにアプリケーションデータ格納部を検索し、検索されたアプリケーションデータが属するグループに所属するアプリケーションデータを呼び出し、目的とするアプリケーションデータを選択することで文字入力を行う。 - 特許庁
The CPU 13 checks the remaining amt. of data in the buffer 12 in timing when a timing signal SYNC becoming a standard for synchronism inputted in synchronism with the data Di is inputted from the outside, performs filter processing for the difference between the data remaining amt. at the check time and a target value, and sets the obtained divider value in the 1/N divider 15. CPU13は、データDiに同期して入力される同期の基準となるタイミング信号SYNCが外部から入力されたタイミングでバッファ12のデータ残量をチェックし、このチェック時のデータ残量と目標値との差分に対しフィルタ処理を施し、得られたデバイダ値を1/Nデバイダ15にセットする。 - 特許庁
Each amount of a-liquid and b-liquid to be supplied this time is controlled to be a target amount corrected by subtracting the previous excess amount while considering the last mixing ratio of the actual discharged amount of the a-liquid to that of the b-liquid when the multiple fluids are mixed in a mixing room while weighing them alternately and the mixture is supplied to the spray gun. 複数の流体を交互に計量しながら混合室で混合して、スプレーガンへ供給する場合に、直前のa液の実吐出量に対する混合比を考慮しながら、a液とb液の各々の液が前回の超過量を修正した目標量にする制御を行う。 - 特許庁
The heating apparatus 5 of the reinforcement sleeve is provided with a heating control part 53 which starts the preheating mode according to the input of a preheating commencement signal and is switched to a heating mode in which the heating is performed at a target temperature for a predetermined time by the input of a heating commencement signal, and the heating apparatus is preliminarily heated before heating the reinforcement sleeve. 補強スリーブの加熱装置5は、予熱開始信号の入力によって予熱モードを開始し、加熱開始信号の入力によって所定時間目標温度に加熱する加熱モードに切り替える加熱制御部53を備え、補強スリーブを加熱処理する前に加熱装置を予熱する。 - 特許庁
More specifically, the unit 34 sets the target brake hydraulic pressure Pt so that the brake hydraulic pressure in brake units 11-14 is reduced by the preset pressure reduction ΔP when the hydraulic pressure change ΔPm of the master cylinder hydraulic pressure Pm detected by a master cylinder hydraulic pressure sensor 32 is a negative value in the predetermined short time interval. 具体的に、ユニット34は、マスタシリンダ液圧センサ32によって検出されたマスタシリンダ液圧Pmの液圧変化量ΔPmが所定の短い時間間隔で負の値であるときに、ブレーキユニット11〜14におけるブレーキ液圧が予め設定された減圧量ΔPにより減圧するように目標ブレーキ液圧Ptを設定する。 - 特許庁
When a location positioned by a GPS positioning means 11 coincides with a communication area of a radio base station including a specific area of a target for a user to stay for a long time, power consumption is suppressed by changing over the cycle of the positioning of the GPS positioning means 11 from the present first cycle to a second cycle longer than the first cycle. GPS測位手段11の測位した位置がユーザの長時間滞在の対象の特定エリアを含む無線基地局の通信エリアに一致するとき、GPS測位手段11の測位の周期を、現在の第1の周期から、これよりも長い第2の周期に切り替えて電力消費を抑える。 - 特許庁
To enable whether a moving exercise is progressed faster than the schedule or later than the schedule during the moving to be easily judged by an exerciser without requiring the detection of information regarding the moving exercise during the moving exercise when the exerciser is going to perform the moving exercise for a determined distance within a target period of time. 決められた距離を目標とする時間で運動者が移動運動しようとする場合に、移動運動に関する情報を移動運動中に検出することを必要とせずに、移動途中において予定よりも進んでいるのか又は遅れているのかを運動者が容易に判断することができるようにする。 - 特許庁
To solve the problem that, when a condition that temperature of an evaporator 30 exceeds a target value is included in restart conditions of idle stop control, the automatic stop time of the engines 10 is shortened as the temperature rising speed of the evaporator 30 during the automatic stop of an engine 10 becomes high and the fuel consumption reducing effect of the engine 10 is reduced. エバポレータ30の温度がその目標値を上回るとの条件をアイドルストップ制御の再始動条件に含む場合、エンジン10の自動停止中におけるエバポレータ30の温度の上昇速度が高くなることでエンジン10の自動停止時間が短くなり、エンジン10の燃費低減効果が低下すること。 - 特許庁
Each camera unit 10 includes a light emitting section 11 which irradiates a target with light, and an imaging section 12 which captures a distance image having for each pixel distance information calculated from a measurement of a time until returning reflection light of irradiation light and luminance information indicating an intensity of the reflection light. 各カメラユニット10は、対象物へ向けて光を照射する発光部11と、照射された光の反射光が戻ってくるまでの時間の測定値から算出される距離情報と前記反射光の強度を示す輝度情報とを画素毎に有する距離画像を取得する撮像部12とを有する。 - 特許庁
In the method for manufacturing a vertical magnetic recording medium that forms a plurality of layers on a disk substrate 110 by sputtering, at least two consecutive layers among the plurality of layers are formed in the same chamber using the same target in a single process time while varying sputter conditions. ディスク基体110上に複数の層をスパッタリングによって成膜する垂直磁気記録媒体の製造方法において、複数の層のうち、少なくとも2つの連続する層を、同一チャンバーにおいて同一のターゲットを用いて1つのプロセスタイム内でスパッタ条件を異ならせて成膜することを特徴とする。 - 特許庁
When respective unit periods defined by a statistic calculation rule 124 are terminated, the statistic system 111 reads all the statistical target information for the unit periods including an event occurrence time point from the storage device 12, executes statistical calculation, and registers the statistical result in statistical information 122 inside the storage device 12. そして、統計システム111は、統計算出ルール124に定義された個々の単位期間が満了すると、その単位期間内に事象発生時点が含まれる全ての統計対象情報を記憶装置12から読み出して、統計計算を実行し、その統計結果を、記憶装置12内の統計情報122に登録する。 - 特許庁
When a time t passes or a target number of revolutions of the motor is reached, a minute driving torque command which provides the wheel with the minute driving torque is output to compensate the mechanical response delay of a driving system, and a brake oil pressure increase command signal is output to increase the brake control pressure in generating minute driving torque (S8). そして、時間tが経過したとき或いは目標モータ回転数に達したとき、微小駆動トルクを与える微小駆動トルク指令を出力して駆動系の機械的な応答遅れを補償すると共に、ブレーキ液圧アップ指令信号を出力して微小駆動トルク発生中のブレーキ制御圧を増圧する(S8)。 - 特許庁
In time of the magnification, when the table having imperfect cell not including a character is present inside the series of small forms designated as the adjustment target, the table is magnified such that a changeable area (a margin and a line space) except an area occupied by a character and a margin on a boundary side is enlarged. その拡大時においては、調整対象として指定された一連の小組の中に、文字を含まない不完全セルを持つ表があったときには、その表は、文字が占める領域と境界側の余白とを除く変更可能領域(余白及び行間)が引き伸ばされるようにして、拡大される。 - 特許庁
To provide a water treatment apparatus suppressing the influence of various components in wastewater, especially adsorbing and removing a substance exerting adverse effect on photocatalytic action beforehand to efficiently decompose target organic matter by a photocatralyst and capable of obtaining decomposition capacity stable over a long period of time. 廃水中の種々の成分の影響を抑制し、特に光触媒作用に悪影響を及ぼす物質をあらかじめ吸着除去し、光触媒により対象とする有機物を効率よく分解することができ、かつ長期間にわたって安定した分解性能が得られる水処理装置を提供する。 - 特許庁
To provide a film carrier tape for mounting electronic component in which a defect can precisely be marked on a target position on a mounting unit without fail and a recognition defect due to dislocation of a defect mark can be reduced at the time of mounting IC, and to provide a defect marking method of the film carrier tape for mounting electronic component. 実装ユニット上の目標位置に精度よく、間違いなく不良マーキングを行うことができ、IC実装時などにおいて、不良マークの位置ずれによる認識不良が低減可能な電子部品実装用フィルムキャリアテープ、および電子部品実装用フィルムキャリアテープの不良マーキング方法の提供。 - 特許庁
In this exercise support method, because movement is performed from a present position to a destination through a route determined based on target calorie consumption, blood sugar level information, and an action history or the like in a route determination step (S107), the user can arrive at the destination by certain arrival time, and performs proper exercise in a pulsation range for aerobic exercise, for example. 経路決定ステップ(S107)で、目標消費カロリー、血糖値情報、および行動履歴などをもとにして決定された経路により、現在位置から目的地へ移動するので、ユーザーが必着時刻までに目的地へ到達できるとともに、たとえば有酸素運動のための脈拍範囲で適正な運動を行う。 - 特許庁
To optimize the form and distribution state of a graphite in a refractory to maximumly exhibit characteristics such as excellent thermal shock resistance and corrosion resistance possessed by the graphite and to target the long-time resistance of the graphite-containing refractory as a lining brick for a converter or the refractory for continuous casting. 転炉内張れんがや連続鋳造用耐火物としての黒鉛含有耐火物の長時間耐用を目的に、黒鉛のもつ耐熱衝撃性、耐食性に優れるという特性を最大限発揮するための耐火物中における黒鉛の形態及び黒鉛の分布状態の最適化を図る。 - 特許庁
To provide a fan control method and a fan controller for changing setting of a fan operation target value for stirring air in a space in which a cold temperature heat source exists at a food store so that electric energy in a predetermined time of an air conditioner is reduced. 食料品店舗などの冷温熱源が存在する空間において、空調機の所定時間内での電力量が減少するように、空間内空気攪拌用のファン運転目標値を設定変更することにより、空調機電力量を節約することができるファン制御方法及びファン制御装置を提供すること。 - 特許庁
To solve a problem that connections concentrate on a specific wireless base station and to suppress waste of time and radio resources by simplifying a communication procedure to identify a target wireless base station to be connected in a wireless LAN system, comprising a plurality of wireless base stations and dispersing connections from wireless terminals. 複数の無線基地局を設置し無線端末からの接続を分散する無線LANシステムにおいて、特定の無線基地局に接続が集中するという問題を解決するとともに、接続すべき無線基地局を特定するまでの通信手順の簡易化によって無線リソースと時間の浪費を抑制することを目的とする。 - 特許庁
To provide a means capable of quickly updating and adding retrieval target data in parallel with retrieving and quickly performing a degeneration operation even when a retrieval processing fails about a full text retrieval system of a character string collation system for retrieving a large amount of data in a short period of time by using a plurality of processors. 本発明は、複数処理装置を用いて大量データを短時間に検索する文字列照合方式の全文検索システムに関し、検索対象データの更新、追加を検索と並行して行うことが可能で、検索処理装置が故障しても、縮退運転を迅速に行える手段を提供することを課題とする。 - 特許庁
During correlation intervals, while a window function is time shifted, the window function is applied to a first signal and a second signal of a pair of radio signals, received at a pair of passive sensors from a target object, to produce a first windowed signals and a second windowed signals for each application. 相関間隔の間、窓関数をタイムシフトさせつつ、目標物体から一対のパッシブセンサで受信された一対の電波信号の内の第1の信号および第2の信号に上記窓関数を繰り返して適用して、各適用ごとに、第1の窓化信号および第2の窓化信号を生成する。 - 特許庁
When the deceleration operation number (frequency) Gn or the deceleration operation time (duration) Gt by a set/coast (deceleration) switch is large, the target deceleration Xgs is set to be large according thereto to enable the traveling speed control of the subject vehicle to meet the request for deceleration of a driver who wishes to rapidly reduce the speed. セット/コースト(減速)スイッチによる減速操作回数(頻度)Gnや減速操作時間(継続時間)Gtが大きいときには、それらに応じて目標減速度Xgsを大きく設定し、速やかに減速したい運転者の減速要求に則した自車両の走行速度制御を可能とする。 - 特許庁
An allocation means 7 allocates one communication resource for which a free area of the communication resource stored in the storage unit 2 satisfies, regarding the access interval target value and the average elapsed time for each web server, a predetermined condition to each web server, and stores, in the storage unit 2, a result of the allocation as a communication resource allocation state to each web server. 割り当て手段7は、記憶部2に記憶させた通信リソースの空き容量が、Webサーバごとのアクセス間隔目標値および平均経過時間に対して、所定の条件を満たす通信リソースを各Webサーバに1つ割り当て、割り当てた結果を各Webサーバへの通信リソース割り当て状態として記憶部2に記憶させる。 - 特許庁
To provide a device for ultrasonic video inspection in which focusing and gain adjustment are automatically executed to an inspection target part of an object to be inspected, work such as the focusing is executed simply and in a short time, and which can confirm whether a C scope image obtained by measurement is a focusing point or not, and a detecting method of a focal position thereof. 被検体の検査対象部に対し自動的に焦点合せとゲイン調整を行い、焦点合せ等の作業を簡単かつ短時間に行い、測定で得たCスコープ像が合焦点か否かを確認できる超音波映像検査装置とその焦点位置検出方法を提供する。 - 特許庁
To prevent light emission elements from making their luminous energy lower than target luminous energy and prevent an abnormal image such as an image irregularity from occurring at the time when APC ends at the point when the influence of return light does not disappear in a case where the return light occurs, and making luminous energy received by light-receiving elements higher than in a normal condition. 戻り光が発生して受光素子の受光量が通常の状態よりも増大してしまうような場合において戻り光の影響が消えない時点でAPCが終了された場合に、発光素子が狙いの光量よりも低下してしまうことを防止し、画像ムラなどの異常画像の発生を防止する。 - 特許庁
In the image sensor, a ramp signal formation portion compares a digital target code with a references code, and the comparison result forms the ramp signal and feeds back generated ramp signal VRAMP to a CDS circuit array in a main single inclination ADC and a single inclination ADC in a ramp signal generating portion, at the same time. イメージセンサでは、ランプ信号生成部が、デジタル目標コードと基準コードとを比較して、その比較結果によってランプ信号を生成し、生成されたランプ信号VRAMPをメイン単一傾斜ADC内のCDS回路アレイと、ランプ信号生成部内の単一傾斜ADCとに同時にフィードバックする。 - 特許庁
To solve the problem wherein limit of change speed is needed since effect on a combustion state is large at the time of cold engine if intake valve open timing IVO is changed by a variable valve gear, and that combustion state is transitionally deteriorated or duration for reaching a target gets longer in former examples in which change speeds are fixed. 吸気弁開時期IVOを可変動弁装置により変化させると、冷機時には、燃焼状態への影響が大きいので、変化速度を制限する必要があるが、一定の変化速度とする従来例では、過渡的に燃焼状態が悪化し、あるいは目標に到達するまでの所要時間が長くなる。 - 特許庁
Immediately after oiling, target exhaust recirculating amount GEGR is decreased as compared with usual (S15), and a second DPT map corresponding to an average cetane number is selected as a map for calculating particulate discharging amount DPT per unit time (S14), thereby calculating collected particulate amount QPT of DPF 32. 給油直後は、目標排気還流量GEGRを通常より減量する(S15)とともに、単位時間当たりのパティキュレート排出量DPTを算出するマップとして、平均的なセタン価に対応する第2DPTマップを選択し(S14)、DPF32の捕集パティキュレート量QPTを算出する。 - 特許庁
The said plan set forth a numeric target to improve 10% of capacity of the international supply chain by 2015 from the viewpoints of time, cost and assuredness, and it also includes actions to improve 8 problems on strengthening the connection of international supply chain such as shortage in transport infrastructure and inefficient custom clearance. 同計画は、2015 年までに国際物流能力を時間・費用・確実性の観点から10%改善するとの数値目標を掲げるとともに、輸送インフラの不足や通関の非効率など、国際物流の連結強化に関する8 つの問題点の改善を図るための行動が盛り込まれている。 - 経済産業省
To provide an oxide sintered compact containing zinc oxide as a main component, aluminum, and gallium and its manufacturing method, a target capable of forming a film continuously for a long time without causing an abnormal discharge in a sputtering method or the like, a transparent electroconductive film of high quality with a low resistance and a high transparency obtained by using it, and a solar cell having a high conversion efficiency. 酸化亜鉛を主成分とし、さらにアルミニウムとガリウムを含有する酸化物焼結体とその製法、スパッタリング法などで異常放電が全く発生せず、連続で長時間成膜できるターゲット、それを用いた低抵抗で高透過性の高品質な透明導電膜、高変換効率の太陽電池を提供。 - 特許庁
To reduce a load caused by collecting attribute information to a monitoring target network and to shorten a processing time required to collect device information when collecting the attribute information of the device from an information processor to be monitored in a system for monitoring the information processor via the network. ネットワークを経由して情報処理装置の監視を行うシステムにおいて監視対象の情報処理装置から装置の属性情報を収集する際に、属性情報の収集によって生じる監視対象ネットワークへの負荷を軽減するとともに装置情報の収集にかかる処理時間を短縮する。 - 特許庁
To provide an apparatus for treating a lesion part in a celom utilizing a self-expansion type stent whose side face is covered with a film, allowing comparatively easy and accurate insertion and arrangement operations up to a target indwelling section of the stent to be performed, and scarcely shutting off blood flow at the time of indwelling operation. 側面が膜により被覆された自己拡張型ステントを利用するものであって、ステントの目的留置部位までの挿入、配置操作が比較的容易且つ正確に行うことができ、更に留置操作時に血流を遮断することがほとんどない体腔内病変部治療用器具を提供する。 - 特許庁
A compiler for compiling a source program to an execution program generates a name reference and solution calling instruction for calling a name solution procedure for solving a name which can be solved only at the time of program execution and an instruction without any side effect having name identification information for identifying the name which can be solved only at the time of program execution and the number of a target register for storing a solved name. 本発明は、ソースプログラムを実行プログラムにコンパイルするコンパイラにおいて、プログラム実行時にしか解決することのできない名前を解決するための名前解決手続きを呼び出す名前参照解決呼び出し命令と、プログラム実行時にしか解決することのできない名前を識別するための名前識別情報及び解決した名前をストアするための目的レジスタの番号を有する副作用のない命令とを生成する。 - 特許庁
A radio base station BTS includes a prediction unit 13 configured to predict the time when a buffer of a mobile station UE as a scheduling target becomes empty based upon TEBS reported by the mobile station UE, and a transmission unit 15 configured to transmit "Zero Grant" instructing the mobile station UE to stop transmitting a data signal through an E-DPDCH based upon the predicted time. 本発明に係る無線基地局BTSは、スケジューリング対象の移動局UEによって通知されたTEBSに基づいて、移動局UEのバッファが空になる時刻を予測するように構成されている予測部13と、移動局UEに対して、予測された時刻に基づいて、E-DPDCHを介したデータ信号の送信を停止するように指示する「Zero Grant」を送信するように構成されている送信部15とを具備する。 - 特許庁
A retrieval display part 2302 makes a display terminal 310 display alarm information generated or restored prior to the time when the checked message has been transmitted as a checked alarm, and makes the display terminal 310 display the alarm information generated or restored posterior to the time when the checked message has been transmitted as an unchecked alarm among the alarm information generated or restored by a monitoring target facility 110 stored in the database 220. 検索表示部2302は、データベース220が記憶する監視対象設備110で発生または復旧した警報情報のうち、確認済みメッセージが送信された時刻以前に発生または復旧した警報情報を確認済み警報として表示端末310に表示させ、確認済みメッセージが送信された時刻より後に発生または復旧した警報情報を未確認警報として表示端末310に表示させる。 - 特許庁
Alternatively, a correction plate having a thickness of 0.8 times or more and 1.0 time or less the target thickness is arranged in the through hole of the work carrier 2 and the grinding pads have a hardness of 70 or more. また、加工キャリアの貫通孔内に配された被処理物の両面を研磨パッドを用いて目標厚みに研磨する平面研磨加工方法であって、該加工キャリアの貫通孔内に、該目標厚みの0.8倍以上1.0倍以下の厚みを有する修正プレートを配し、該研磨パッドが、硬度70以上を有することを特徴する平面研磨加工方法を提供する。 - 特許庁
In this gas turbine device wherein the air-fuel mixture is combusted, and the combustion gas generated in the combustion is supplied to the turbine 1 to rotate and drive the turbine, the acceleration of the turbine 1 is continuously changed along a predetermined target value for a predetermined time from the start of the change of speed, when the rotating speed of the turbine 1 is changed. 空気と燃料との混合気を燃焼させ、該燃焼により発生した燃焼ガスをタービン1に供給することによりタービン1を回転駆動するガスタービン装置において、タービン1の回転数を変速させる際、該変速が開始された時点から所定時間の間は、タービン1の加速度を所定の目標値に沿って連続的に変化させる。 - 特許庁
When the initial state is detected, until an absolute value of a target current Im* becomes a determination current Im0 or less or during a predetermined time T1 is passed after the initial state is detected, initial proportional gain Kp2 and initial integration gain Ki2 smaller than usual proportional gain Kp1 and usual integration gain Ki1 are set. 初期状態を検出した時に、目標電流Im*の絶対値が判定電流Im0以下となるまで、若しくは、初期状態を検出してから所定時間T1を経過するまでの間に、通常比例ゲインKp1及び通常積分ゲインKi1よりも小さな初期比例ゲインKp2及び初期積分ゲインKi2を設定する。 - 特許庁
When a state wherein a vehicle has not more than a prescribed acceleration or deceleration continues for a prescribed time with the brake stepped on in a state where the inertial traveling of the vehicle on the downward slope is detected by an inertial traveling detection means, a change ratio limit on a lower limit value of a target rotation speed for the inertial traveling of the input-side rotation body is forbidden. 慣性走行検出手段により車両が降坂路を慣性走行していることを検出した状態のもとで、ブレーキが踏み込まれ、かつ所定の加減速度以下の状態が所定時間継続したときには、入力側回転体の慣性走行用目標回転数の下限値にかかる変化率制限を禁止する。 - 特許庁
To reduce the smoke amount in an exhaust gas, while maintaining the acceleration performance in response to the accelerator operation at the acceleration start time of a vehicle favorably, in an exhaust gas circulating control device A which can control an exhaust gas circulating amount and keep an air-fuel ratio to a prescribed target value in order to reduce both NOx and smoke in the exhaust gas. 排気中のNOx及びスモークを両方共に低減させるべく、排気還流量を制御して空燃比を所定の目標値に保つようにした排気還流制御装置Aにおいて、車両の加速開始時にアクセル操作に対応する加速性能を良好に維持しつつ、排気中のスモーク量の低減を図る。 - 特許庁
A setting apparatus 44F sets D^*utymf=D^*utyf to a pressure intensifying pump (motor) target manipulated variable Dutymf as it is when torque shortage is not determined, and increases Dutymf for correction by a one-shot pulse signal with a prescribed time width, when torque shortage is determined, so as to prevent a low frequency fluctuation in fluid pressure with torque shortage. 設定器44Fは、トルク不足の判断がない場合、増圧ポンプ(モータ)目標操作量Dutymfに上記のD^*utymf=D^*utyfをそのままセットするが、トルク不足の判断がある場合、Dutymfを所定時間幅のワンショットパルス信号により増大補正して、トルク不足に伴う液圧の低周波変動を防止する。 - 特許庁
A major axis end point detecting part 34, a front view minor axis end point detecting part 36 and a side view minor axis end point detecting part 38 detect the end points of the respective major and minor axes on the basis of the major axis/minor axis set in the ellipsoid axis setting parts 32 and the surface image of target tissue at every time phase outputted from an edge extraction part 24. 長軸端点検出部34、正面図短軸端点検出部36および側面図短軸端点検出部38は、楕円体軸設定部32において設定された長軸・短軸、および、エッジ抽出部24から出力される各時相ごとの対象組織表面画像に基づいて長軸・短軸それぞれの端点を検出する。 - 特許庁
In a fixed point observation is performed at prescribed time intervals to observe the secular change of the buildings, the automatic tracking total station 1 is set in an optional position PM allowing the observation operation, and successively turned to track each observation target point Pi on the basis of each point observation order and each point coordinate of the basic data to obtain a fixed point observation coordinate data for each point Pi. 建造物の経年変化をみるために所定期間をおいて定点観測を行う際には、観測動作可能な任意位置PMに自動追尾トータルステーション1を設置し、基本データの各点観測順序及び各点座標に基づいて、各観測目標点Piに、順次、旋回追尾させて各点Piの定点観測座標データを取得する。 - 特許庁
The portable back stop disposed in the rear of a target at the time of training shooting in order to prevent penetration of bullet and to collect the bullet comprises a bulletproof film 3 having a decelerating material provided removably like a blind on the front face of a pyramidal back stop frame 7 and removably on the opposite side faces and the ceiling face of the pyramidal frame. 射撃訓練時に、標的後方に設置した弾丸貫通防止用及び弾丸回収用の可搬型のバックストップとして、四角柱状のバックストップ枠体7の正面に減速材を備えた防弾膜3を簾状に着脱自在に設ける他、四角柱状の枠体の両側面、天井面に着脱自在に配置したバックストップ2を用いる。 - 特許庁
In the vehicle provided with the engine 1 with exhaust turbocharger and the fluid transmission device including the lock-up clutch 23, when a connecting condition of the lock-up clutch is established, operation for reducing a rotating speed target value of the engine for a fixed time is executed prior to lock-up to avoid surging associated with the drop of engine speed in lock-up. 排気ターボチャージャ付きエンジン1を搭載するとともに、ロックアップクラッチ23をそなえ流体伝動装置を有する車両において、ロックアップクラッチの接続条件の成立時に、ロックアップに先立ち一定時間エンジンの回転数目標値を低下させた運転を実施し、ロックアップ時のエンジン回転数降下に伴うサージングの発生を回避する。 - 特許庁
To provide a reinforcing structure for a concrete building capable of permitting easy execution of the work in a short period of time, offering good appearance of the building after the work, and also achieving effective reinforcement by using small quantity of members and small amounts of materials, which can be applied also to an existing building such as a multiple dwelling house wherein relatively narrow target surfaces to be reinforced exist intermittently. 短時間で容易に施工することができ、施工後の美観性が良好であり、比較的狭い補強対象面が断続的に存在する集合住宅等の既設建築物に対しても適用することができ、さらには、少量の部材および材料で効果的な補強をなし得る、コンクリート建築物の補強構造を提供する。 - 特許庁
In the hybrid hot water supplier, a first control device 100 raises the heating capacity of a heat pump unit 1 to the value of the upper stage if the difference between the target outlet temperature of a heating medium of a heat exchanger 4 for heat radiation and the outlet temperature of the heating medium of the heat exchanger 4 for heat radiation is ≥5°C continuously for the first prescribed time. ハイブリッド式給湯装置によれば、第1の制御装置100は、放熱用熱交換器4の熱媒体目標出口温度と放熱用熱交換器4の熱媒体出口温度との差が、第1の所定時間以上継続して5℃以上である場合には、ヒートポンプユニット1の加熱能力をより上段の能力値に上げる。 - 特許庁
In the deposition of the film of dielectric material, the plasma emission intensity of at least one element in the plasma emission spectrum emitted by plasma is fluctuated by changing the distance between the substrate 41 and a target 71 by the vertical movement of a substrate holder 72 by means of the operation of a driving device 85, over the whole length of the deposition time of the dielectric material. 誘電体材料の成膜時において、該誘電体材料の成膜時間全体に亘って、プラズマが発するプラズマ発光スペクトル中における少なくとも1つの元素のプラズマ発光強度を、駆動装置85の作動による基板ホルダー72の上下移動により基板41とターゲット71との間の距離を変化させることで変動させる。 - 特許庁