The voltage controlled oscillator includes an inductor circuit 110, C-coupling type variable capacitance circuits 120 and 140, a direct-coupling type variable capacitance circuit 130, and a negative resistance circuit 160, which are connected in parallel, and a reference voltage generating section 180 that generates reference voltages Vref1 and Vref2. 本発明の電圧制御発振器は、並列接続されたインダクタ回路110、C結型可変容量回路120及び140、直結型可変容量回路130、及び負性抵抗回路160と、基準電位Vref1及びVref2を生成する基準電位発生部180とを備える。 - 特許庁
When a variable gain control circuit 1 controlled by a gain control voltage V8 amplifies or attenuates an input signal, a rectifier circuit 2 rectifies an output signal of the variable gain control circuit 1, and a voltage comparator 3 compares an output signal of the rectifier circuit 2 with an optionally set voltage. 利得制御電圧V8により制御される可変利得制御回路1で入力信号を増幅しまたは減衰させるときに、可変利得増幅回路1の出力信号を整流回路2で整流し、整流回路2の出力信号と任意に設定した電圧とを電圧比較器3で比較する。 - 特許庁
In this frequency synthesizer device consisting of a phase comparator 1, a low-pass filter 2, a voltage-controlled oscillator 3, a variable frequency divider 4 and a frequency division ratio control circuit 5, the frequency division ratio of the divider 4 changes on time base in the control circuit 5, and its time average value is controlled so as to include values below the decimal point. 位相比較器1と、ローパスフィルタ2と、電圧制御発振器3と、可変分周器4と、分周比制御回路5とからなる周波数シンセサイザ装置において、分周比制御回路5で、可変分周器4の分周比が時間的に変化し、かつその時間平均の値が小数点以下の値を含むように制御する。 - 特許庁
A plurality of floodlights for irradiating a driver from above, below, right, or left or from a plurality of directions are provided in front of the driver's seat of an automobile, and irradiation intensities of light beams from the respective floodlights are controlled with a basic controlled variable set corresponding to the illuminance in the cabin (110 to 160). 自動車の運転席前方に、運転者を上方、下方、右方、左方の何れか若しくは複数方向から照射するための複数の投光器を設け、車室内の照度に応じて設定した基本制御量にて、各投光器からの光の照射強度を制御する(110〜160)。 - 特許庁
It is determined that a throttle valve reaches the opener regulating opening, when the throttle valve temporarily almost stops before reaching the target throttle opening while the throttle valve is so driven as to stride over the opener regulating opening, and when a code of the value (I controlled variable) of an integral member out of the controlled variables of a drive motor for the throttle valve is reversed. スロットルバルブがオープナ規制開度を跨ぐように駆動される期間に、スロットルバルブが目標スロットル開度に到達する前に一時的にほぼ停止して、スロットルバルブの駆動モータの制御量のうちの積分項の値(I制御量)の符号が反転したときに、スロットルバルブがオープナ規制開度に到達したと判断する。 - 特許庁
To stably converge an engine speed to a target value in an internal combustion engine in which an intake pipe negative pressure is controlled by an electronic control throttle while the intake air quantity of the engine is controlled by the operation of a variable valve train that can change the lift characteristics of an intake valve continuously. 吸気バルブのリフト特性を連続的に変更可能な可変動弁機構の動作によって機関の吸入空気量を制御しつつ、電子制御スロットルによって吸気管負圧を制御する内燃機関において、機関回転速度を目標値に対して安定的に収束させることができるようにする。 - 特許庁
The lubricant application blade is controlled to have a variable contact pressure to an image support, and before imaging, the magnitude of contact pressure of the lubricant application blade is controlled to avoid an unsuitable case depending on the magnitude of a photoreceptor drum static torque (or depending on the device not under that condition). 潤滑剤塗布ブレードを、像担持体への当接圧を可変に制御可能に構成し、作像前に感光体ドラム静トルクの大きさに対応して(または、そのような条件下に装置がなったことに対応して)、不適切な場合を回避すべく潤滑剤塗付ブレードの当接圧の大きさを制御する。 - 特許庁
Furthermore, an oscillation circuit of the voltage controlled oscillator is provided with the voltage variable capacitive element 3 to control the oscillating frequency of the oscillation circuit and by combining interdigitally regions of the source and the gate in the voltage controlled oscillator the channel resistance is reduced. また、この電圧可変容量素子3を発振回路中に具備し、前記発振回路の発振周波数を制御した電圧制御発振器において、さらに、前記ソースと前記ゲートとを形成する各領域を櫛歯状にして噛み合わせることによって前記チャンネル抵抗を小さくした構成とする。 - 特許庁
To stably converge an engine speed to a target value in an internal combustion engine in which an intake pipe negative pressure is controlled by an electronic control throttle while the intake air quantity of the engine is controlled through the operation of a variable valve train that can change the lift characteristics of an intake valve continuously. 吸気バルブのリフト特性を連続的に変更可能な可変動弁機構の動作によって機関の吸入空気量を制御しつつ、電子制御スロットルによって吸気管負圧を制御する内燃機関において、機関回転速度を目標値に対して安定的に収束させることができるようにする。 - 特許庁
A current controlled variable operating part 51 calculates a current command value to be supplied to the electromagnet corresponding to a target position signal of the moving element determined on the basis of the valve clearance length by a target control position determining part. このバルブクリアランス長さに基づいて目標制御位置設定部54が設定した可動子の目標位置信号に応じて、電流制御量演算部51が電磁石に通電すべき電流指令値を計算する。 - 特許庁
To set an appropriate steering controlled variable in a case of controlling the steering using the both of a vehicle motion target value according to the steering operation of a driver and a vehicle motion target value by an automatic steering. 運転者の操舵操作に応じた車両運動目標値と自動操縦による車両運動目標値との両方を使って転舵制御する場合においても、適正な転舵制御量を設定する。 - 特許庁
To provide a voltage-controlled oscillator, suitable for downsizing where an equivalent series resistance component of a capacitor in a resonator circuit section is small and the temperature characteristic of a variable capacitance diode is corrected and to provide its adjustment method. 共振回路部内のコンデンサの等価直列抵抗成分が小さく、バリキャップダイオードの温度特性が補正され、且つ小型化に適した電圧制御型発振器及びその調整方法を提供する。 - 特許庁
The voltage controlled quartz oscillator is provided with a crystal resonator 2, an inverting amplifier 1, DC cut capacities 3, 4, a control voltage input terminal 12, bias resistors 5, 6 and voltage variable capacity elements 7, 8. 電圧制御水晶発振器は、水晶振動子2、反転増幅器1、直流カット容量3、4、制御電圧入力端子12、バイアス抵抗5、6、及び電圧可変容量素子7、8を備えている。 - 特許庁
A metal belt 19 is wrapped around across a primary pulley 17 and a secondary pulley 18, and the groove widths of the respective pulleys 17, 18 are controlled by hydraulic pressure so that the continuously variable transmission 15 continuously changes the transmission gear ratio. 無段変速機15は、プライマリプーリ17とセカンダリプーリ18との間に金属ベルト19を掛け渡し、油圧により各プーリ17,18の溝幅を制御することで変速比を連続的に変化させる。 - 特許庁
From the results of the display on the normal pattern display devices a-d, mobile pieces 81a-81d of the corresponding normal variable prize ball devices A-D are opened and controlled to offer a first state advantageous for the game players. 普通図柄表示装置a〜dの表示結果によって、対応する普通可変入賞球装置A〜Dの可動片81a〜81dを開放し、遊技者にとって有利な第1の状態に制御する。 - 特許庁
In this PLL synthesizer, a closed loop is composed of a reference signal generator 1, a variable frequency divider 2 for reference signal, a phase comparator 5, a loop filter 6, a voltage controlled oscillator 3 and a frequency divider 4 for oscillation signal. 基準信号発生器1、基準信号用可変分周器2、位相比較器5、ループフィルタ6、電圧制御発振器3、及び発振信号用分周器4により閉ループを構成するPLLシンセサイザ。 - 特許庁
The control device for a power transmission device is applied to a vehicular power transmission device having a motor, an electric motor, a stepped shifting part, and a continuously variable shifting part wherein a differential state is controlled by the electric motor. 動力伝達装置の制御装置は、原動機と、電動機と、有段変速部と、前記電動機により差動状態が制御される無段変速部と、を有する車両用の動力伝達装置に適用される。 - 特許庁
The oscillation circuit 11 is a Colpitts type oscillation circuit or a Pierce type oscillation circuit, and the frequency-voltage controlled circuit 12 comprises a circuit including a capacitor and an inductor and at least one variable capacitor. 発振回路11は、コルピッツ型発振回路、又はピアース型発振回路であり、周波数電圧制御回路12は、容量素子とインダクタと少なくとも1つの可変容量素子とを有する回路からなる。 - 特許庁
When a value from the BPF 310 is a minus value or a plus value, it is decided that a frequency is shifted from an original frequency, and capacitance of a variable capacitor 302 is controlled such that the frequency becomes the proper frequency. BPF310からの値が、マイナスの値、またはプラスの値の場合、周波数が本来の周波数よりずれていると判断され、適切な周波数になるように、可変容量コンデンサ302の容量が制御される。 - 特許庁
A spark ignition type gasoline engine provided with a variable compression ratio mechanism for changing a top dead center position of a piston is basically controlled to a high compression ratio in a low load region and to a low compression ratio in a high load region. ピストンの上死点位置を変化させる可変圧縮比機構を備えた火花点火式ガソリン機関であって、基本的に、低負荷域では高圧縮比に、高負荷域では低圧縮比に制御される。 - 特許庁
This voltage drop is variable according to the current value of the source 52 controlled by the element 13, and an output signal level at the terminal 61 can be regulated according to the voltage applied to the terminal 13. この電圧降下は制御端子13で制御される電流源52の電流値によって可変であり、制御端子13に印加する電圧によって端子61における出力信号レベルを調整できる。 - 特許庁
To obtain a process controlling method that can quickly and precisely track a controlled variable outputted from a controlling object to a target value, and can improve process throughput, and to provide a method for manufacturing electronic device. 制御対象から出力される制御量を迅速、且つ正確に目標値へ追従させることができ、プロセスのスループットを向上させることができるプロセス制御方法並びに電子デバイス製造方法を得る。 - 特許庁
Capacity values of the variable capacitors 4a and 4b and the oscillation frequency of the voltage-controlled SAW oscillation circuit are adjusted based upon an oscillation frequency control signal inputted to the oscillation frequency control terminal 5. 発振周波数制御端子5に入力される発振周波数制御信号に基づいて可変容量4a、4bの容量値及び電圧制御SAW発振回路の発振周波数を調整する。 - 特許庁
As a result, the light illumination device 17 can be certainly horizontally maintained relative to the support member 2 and an illumination direction of the light from the light illumination device 17 can be correctly and certainly variable-controlled. この結果、光照射装置17を支持部材2に対して確実に水平に維持することができ、光照射装置17からの光の照射方向を正確にかつ確実に可変制御することができる。 - 特許庁
According to the level of a low tone component of input signals, the booster circuit changes the cutoff frequency of a cutoff frequency variable low tone pass filter 4 and the amplification gain of a voltage controlled amplifier circuit 6 at the same time. 入力信号の低音域成分のレベルに応じて、カットオフ周波数可変型低音域通過フィルタ4のカットオフ周波数と電圧制御型増幅回路6での増幅利得とを同時に変化させる。 - 特許庁
Opening of a flow rate variable valve 22 is controlled, to continuously change cooling water flow, according to the temperature of cooling parts 25, 26 of the vacuum pump P for smoothly controlling the temperature of the cooling part of the vacuum pump. 真空ポンプPの冷却部25、26の温度に応じて流量可変バルブ22の開度を制御して冷却水流量を連続的に変化させ、真空ポンプの冷却部の温度をなめらかに制御する。 - 特許庁
The capacity of the variable displacement pump 1 is controlled in response to the highest load pressure out of load pressure of the brake clutch circuit 19 in the downstream of the flow-control circuit 35, load pressure of the steering circuit 22, and load pressure of the working device circuit 21. 流量制御回路35の下流側におけるブレーキクラッチ回路19の負荷圧と、ステアリング回路22の負荷圧と、作業機回路21の負荷圧とのうちで最高圧の負荷圧に応じて、可変容量ポンプ1の容量を制御する。 - 特許庁
Thus, a circuit in which a circuit Q is higher and an energy loss is smaller can be realized in comparison with the case where an oscillation frequency is controlled by using a variable capacitance diode such as the conventional Colpitts oscillation circuit. これにより、従来のコルピッツ型の発振回路のように可変容量ダイオードを用いて発振周波数を制御する場合と比較して、回路Qが高く、エネルギー損失が少ない回路を実現できる。 - 特許庁
A voltage-controlled oscillator comprises a parallel resonance circuit including an inductor circuit, a variable capacitance circuit, and a high-frequency switching circuit, a negative resistance circuit, a frequency control section, and a frequency tuning sensitivity control section. 電圧制御発振器は、インダクタ回路と可変容量回路と高周波スイッチ回路とで構成された並列共振回路と、負性抵抗回路と、周波数制御部と、周波数感度制御部とを備える。 - 特許庁
To provide a variable wavelength distribution compensation system for analog optical transmission in which distribution compensation on a fiber transmission line can be controlled with high accuracy by detecting a quantity directly corresponding to a transmission quality in analog optical transmission. アナログ光伝送における伝送品質に直接対応した量を検知し、ファイバ伝送路の分散補償制御を高精度に行えるアナログ光伝送用可変波長分散補償システムを提供する。 - 特許庁
The voltage converter comprises an amplifier circuit with a variable gain controlled such that the gain applied for the generation of the voltage signal is adjusted to the input voltage range of the analog/digital converter according to a transfer function. 電圧変換器は、電圧信号の発生のために印加される利得が伝達関数によりアナログ/デジタル変換器の入力電圧範囲に調整される可変利得を有する増幅回路を含んでいる。 - 特許庁
To perform clock control in dejittering, while satisfying a predetermined drift rate and to shorten the time until a clock-controlled variable in dejittering is approximately converged and the clock control can be performed, while satisfying the predetermined drift rate. デジッタリングにおけるクロック制御において、所定のドリフトレートを満足しながら制御し、かつ、デジッタリングのクロック制御量がほぼ収束して所定のドリフトレートを満足しながら制御できるまでの時間を短くする。 - 特許庁
A hydraulic motor 11 is rotated by pressure oil from a variable displacement piston pump 5 controlled by an operation bar 2, and the rotating speed and rotating direction of the blade 12 connected directly to the hydraulic motor 11 is adjusted. 操作レバー2によって制御される可変容量形ピストンポンプ5からの圧油にて油圧モータ11を回転させ、油圧モータ11に直結されているブレード12の回転数および回転方向を調整する。 - 特許庁
When the wavelength of a laser beam of a wavelength variable laser is controlled (step S0), an optical system or a hologram recording medium is moved (step S1), and a state where a light beam is made incident on a wavelength control pattern is made. 波長可変レーザのレーザ光の波長を制御する際(ステップS0)には、光学系ないしはホログラム記録媒体を移動して(ステップS1)、波長制御パターンに光ビームが入射される状態にする。 - 特許庁
The microcomputer 11 sets a control resolution, at the time when the microcomputer 11 controls the electronic throttle 1 with the output of the controlled variable DUTY, to be higher than an input resolution during input of the actual opening TA. マイコン11は、実開度TAを入力するときの入力分解能に対して、マイコン11が制御量DUTYの出力により電子スロットル1を制御するときの制御分解能を高く設定している。 - 特許庁
To provide an operating speed control device for an electropneumatic positioner, capable of preventing sudden and great operation of a control valve when an actuator controlled variable is greatly changed in accordance with a PID control signal. PID制御の信号に基づきアクチュエータ制御量が大幅に変更された場合でも、調整弁が急峻かつ大幅に作動されるのを防止できる電空ポジショナの作動速度制御装置を提供する。 - 特許庁
A plurality of Peltier modules 1 overlappedly arranged vertically, and a temperature variable operation for the temperature-controlled object 9 arranged on an upper end in the uppermost stage of Peltier module 1 is carried out with control by the temperature controller. ペルチェモジュール1を上下に重ね合わせて複数配置し、最上段のペルチェモジュール1の上端上に配置した被温度制御対象物9の温度可変動作を温度制御装置の制御により行う。 - 特許庁
To produce a semiconductor integrated circuit, in which a PLL circuit having a desired frequency variable range is packaged while using the voltage controlled oscillator(VCO) of an LC resonance type improved in phase noise characteristics, with high yield. 位相雑音特性の優れたLC共振タイプの電圧制御発振器を使用し、且つ、所望の周波数可変範囲を有するPLL回路を搭載した半導体集積回路を、高歩留まりで製造可能にする。 - 特許庁
In a device and a method for estimating the rotational speed ω of an electromotor in an idling state, a motor is controlled by a variable speed driver which generates reference AC voltages Va, Vb. 空転状態の電動機の回転速度ωを推定する装置および方法に関し、その方法は基準交流電圧Va、Vbを発生させることによって電動機を制御する可変速駆動装置で実行される。 - 特許庁
A variable displacement control device having an actuator mechanism connected to a swash plate of the fluid transitional move device to be controlled by a proportional valve unit is used for controlling displacement of the fluid transitional move device. 本発明は、流体並進運動装置のスウォッシュプレートに連結されかつ比例弁装置によって制御されるアクチュエータ機構を有する可変変位制御装置を用いて、流体並進運動装置の変位を制御する。 - 特許庁
If the noise is high and the transmission signal is not detectable by the phase comparator, the frequency of the noise varies rapidly to result in that the phase of the variable oscillator cannot be followed up and controlled within a certain range. 一方、前記雑音が大きく、伝送信号を位相比較器で検出不可能となると、雑音の周波数は高速で動くため可変発振器の位相を一定の範囲内に追従制御することが不可能となる。 - 特許庁
An imaging unit acquires multiple image data for generating panorama image data by imaging as panorama shooting, while a variable mechanism of an imaging visual field for panning or tilting, or the like is driven and controlled to change the imaging visual field. パン・チルト等の撮像視野の可変機構を駆動制御して撮像視野を変化させながら、パノラマ撮像として撮像部に撮像によるパノラマ画像データの生成用の複数の画像データの取得を実行させる。 - 特許庁
Thus, variable resistance circuits (R41-R4n) are inserted into the feedback loop and ON/OFF of switching transistors T61-T6n is selectively controlled, such that impedance of the feedback loop is adjusted, resonance is eliminated and stabilization is attained. そこで、帰還ループに可変抵抗回路(R41〜R4n)を挿入しておき、スイッチングトランジスタT61〜T6nを選択的にオンオフ制御するすることにより、帰還ループのインピーダンスを調整して、共振をなくし安定化を図る。 - 特許庁
When the double-sided printing is consecutively performed and the temperature of the secondary transfer roller rises, the determining processing of the controlled variable of the resist is performed, so that the color shift is effectively prevented. これにより、両面印刷が連続して実行されて2次転写ローラの温度が上昇した場合には、レジスト制御量の制定処理が実行されるため、色ずれを効果的に防止することが可能となる。 - 特許庁
When the pressure of gas supplied to the combustion chamber Ea reaches a predetermined set value, the valve timing variable mechanism 53 is controlled by the control computer C to make the intake valve 51 perform early closing or late closing. 燃焼室Eaに供給する気体の圧力が予め設定された値に達すると、吸気弁51に早閉じ又は遅閉じを実行させるべく制御コンピュータCによってバルブタイミング可変機構53が制御される。 - 特許庁
This device has the shape variable mirror which has one or plural piezoelectric elements deformed by each of the piezoelectric elements by the control voltage impressed to the electrodes for the plural piezoelectric elements and is controlled in the shape of a mirror finished surface. 複数の圧電素子用電極に印加される制御電圧によって、圧電素子用電極ごとに変形される1又は複数の圧電素子を有する、鏡面の形状が制御される形状可変鏡を有する。 - 特許庁
Oscillation frequency (switching frequency) of the self-excited oscillation drive circuit is variably controlled, by making the impedance of the parallel resonant circuit variable, corresponding to a level change in a secondary DC output voltage. そして、二次側直流出力電圧のレベル変動に応じて上記並列共振回路のインピーダンスが可変されるようにすることで、自励発振駆動回路の発振周波数(スイッチング周波数)を可変制御する。 - 特許庁
The focusing or the variable power operation and paradox correction are controlled by a single mechanism, the binocular magnifier 10 is made into light weight and small size, the mechanism is simplified, and the binocular magnifier is inexpensively manufactured. 焦点調節または変倍操作とパララックスの補正とを単一の機構で制御することができ、双眼拡大鏡10を軽量、小型にするとともに機構を簡略化して安価に製造することができる。 - 特許庁
To precisely correct the main scanning magnitude of a light beam even when the write-in clock of a light beam is controlled on the basis of counted number of a clock obtained by measuring at two points in a region where a variable phase control is unapplicable. 位相可変制御を適用できない領域で2点間計測して得たクロックのカウント数に基づいて光ビームの書込みクロックを制御しても、光ビームの主走査倍率を精密に補正できるようにする。 - 特許庁
When an operation of a virtual mechanism model interlocked with a controller 103 is started to be calculated, a driving control part 108 of the controller 103 calculates a controlled variable for a target value according to a control program 109. 制御装置103と連動する仮想機構モデルの動作計算を開始すると、制御装置103の駆動制御部108は、目標値に対する制御量を制御プログラム109により算出する。 - 特許庁