「ctl1」を含む例文一覧(31)

  • A controller CTL1 counts the charging time of the capacitor by its counter.
    制御部CTL1は、そのカウンタでキャパシタの充電時間をカウントする。 - 特許庁
  • A control circuit 100 outputs a signal for the control signal line CTL1.
    制御回路100は、制御信号線CTL1の信号を出力する。 - 特許庁
  • The control signals CTL1, CTL2 are independent of each other.
    制御信号CTL1と制御信号CTL2とは互いに独立している。 - 特許庁
  • An oscillating frequency control voltage VCTL is supplied to the control terminal CTL1 of equipment 22 through the oscillating frequency control terminal 24 of the oscillator 2.
    遅延補間器22の制御端子CTL1は、電圧制御発振装置2の発信周波数制御端子24を介して、発振周波数制御電圧VCTLを供給される。 - 特許庁
  • The circuit 42 decides whether or not to supply an operation instruction ib to an operating part 20 based on these signals and 1st and 2nd control signals CTL1 and CTL2 supplied externally.
    これらの信号と外部から供給される第1,第2の制御信号CTL1,CTL2とに基づいてイネーブル回路42は、演算命令ibを演算部20に供給するか否かを決定する。 - 特許庁
  • The control signal CTL1 is used for controlling a composition ratio of individual image of a plurality of basic depth model types.
    制御信号CTL1は、複数の基本奥行きモデルタイプの各画像の合成比率を制御する。 - 特許庁
  • A control signal CTL1 operates a QPSK modulation section 214 and an offset synthesizer 213.
    コントロール信号CTL1により、QPSK変調部214、オフセットシンセサイザ213を動作状態にする。 - 特許庁
  • The first disconnection circuit 18 is provided on a path of a control signal CTL1 to be inputted to the delay circuit 16 to disconnect the control signal CTL1 while the reset signal POROUT is active.
    第1の遮断回路18は、遅延回路16に入力される制御信号CTL1の経路上に設けられ、リセット信号POROUTが活性状態の間、制御信号CTL1を遮断する。 - 特許庁
  • A control signal generating circuit 5 delays the signal CTL2 behind the signal CTL1 when switching is made from emission to quenching, and delays the signal CTL1 behind the signal CTL2 when switching is made from quenching to emission.
    制御信号生成回路5は、発光から消光への切替時は信号CTL1よりも信号CTL2を遅延させ、消光から発光への切替時は信号CTL2よりも信号CTL1を遅延させる。 - 特許庁
  • The second disconnection circuit 19 is provided on a path of the control signal CTL1 outputted from the delay circuit 16 to disconnect the control signal CTL1 while the reset signal POROUT is active.
    第2の遮断回路19は、遅延回路16から出力される制御信号CTL1の経路上に設けられ、リセット信号POROUTが活性状態の間、制御信号CTL1を遮断する。 - 特許庁
  • The signal PGMA is set to a low level, the signal PGMB is set to a high level, and the signals CTL1, CTL2 are set to a low level in the normal operating mode.
    通常動作モードではPGMAをローレベル、PGMBをハイレベル、CTL1およびCTL2をローレベルにする。 - 特許庁
  • The delay circuit 105 has terminals CTL1, CTL2 for setting the delay time and can select the terminal as the need arises.
    遅延回路105には遅延時間設定用の端子CTL1、CTL2があり、必要に応じ選択することができる。 - 特許庁
  • The voltage converting section P1 is turned on by variation of its control signal CTL1 to deliver an output voltage VOUT1.
    電圧変換部P1は、その制御信号CTL1の変化によってオンして出力電圧VOUT1を出力する。 - 特許庁
  • In the level shifter circuit, a control signal CTL1 controls a P channel MOS transistor MP1 and a control signal CTL2 controls an N channel MOS transistor MN1 respectively.
    Pチャネル型のMOSトランジスタMP1を制御信号CTL1で、Nチャネル型のMOSトランジスタMN1を制御信号CTL2で、それぞれ制御する。 - 特許庁
  • When the output voltage VOUT0 from the voltage converting section P0 reaches a specified voltage, a control signal generating section VM1 varies a control signal CTL1 actively.
    制御信号発生部VM1は、電圧変換部P0の出力電圧VOUT0が規定電圧に達すると、制御信号CTL1をアクティブに変化させる。 - 特許庁
  • Air pressure adjusting devices 220 and 222 are constituted to adjust air pressure of rear tires 210 based on control signals CTL1 and CTL2 from each ECU 230.
    空気圧調整装置220,222は、それぞれECU230からの制御信号CTL1,CTL2に基づいてリヤタイヤ210の空気圧を調整可能に構成される。 - 特許庁
  • Thus, the polarity inversion instruction signal REF does not need to be outputted from the controller CTL1, and this reduces the number of the output terminals and contributes to cost reduction.
    これにより、コントローラCTL1から極性反転指示信号REFを出力する必要がなく、出力端子数を減少させてコスト低減に寄与することができる。 - 特許庁
  • When the output circuits 8, 9 are brought into an on-off state according to the pulse width modulated signals CTL1, CTL2, the terminal of the filament 11a is connected to a lower potential side.
    出力回路8,9は、パルス幅変調信号CTL1,CTL2に応じてオフ状態となるとき、フィラメント11aの端子を低電位側に接続する。 - 特許庁
  • A binary counter 1, a comparator circuit 2, a counter 3, an inverter 4, and AND circuits 5, 6 output pulse width modulated signals CTL1, CTL2 of duty ratios in accordance with set data D0-D5.
    バイナリカウンタ1、比較回路2、カウンタ3、インバータ4及びAND回路5,6は、設定データD0〜D5に応じたデューティー比のパルス幅変調信号CTL1,CTL2を出力する。 - 特許庁
  • As a signal at a control signal line CTL1 becomes high so as to turn off a transistor Tr12, the organic light emitting diode OLED10 is cut off from a power supply line Vdd and turns off.
    制御信号線CTL1の信号がハイになるとトランジスタTr12がオフされて、OLED10と電源供給線Vddの間が遮断されて消灯する。 - 特許庁
  • A luminance adjustment part 110 of an image processor 100A corrects an input image signal Gin on the basis of a luminance control signal CTL1 to generate an output image signal Gout.
    画像処理装置100Aの輝度調整部110は輝度制御信号CTL1に基づいて入力画像信号Ginを補正して出力画像信号Goutを生成する。 - 特許庁
  • A control part CTL1 controls the power supply to the heaters HT1 to HT3 based on a detected voltage of the both-end voltage detection circuit by the voltage and the detected temperature from the temperature sensor TH21.
    制御部CTL1は、両端電圧検出回路の検出電圧と温度センサTH21の検出温度に基づいてヒータHT1〜HT3への電力供給を制御する。 - 特許庁
  • The control data generation section 320 generates the pieces of current control data, CTL1 to CTL3 so that the respective monitor current signals have the same current value, and supplies them to the drive modules DR1 to DR3.
    制御データ生成部320は、各モニタ電流信号の電流値が等しくなるように電流制御データCTL1〜CTL3を生成して駆動モジュールDR1〜DR3に供給する。 - 特許庁
  • The output circuits 8, 9 switches on-off a positive DC voltage Vfs supplied from a filament power source 7 according to the pulse width modulated signals CTL1 CTL2 and applies pulse-like output voltages F1, F2 to a filament 11a.
    出力回路8,9は、フィラメント電源7から供給される正の直流電圧Vfsをパルス幅変調信号CTL1,CTL2に応じてオン/オフし、パルス状の出力電圧F1,F2をフィラメント11aに印加する。 - 特許庁
  • A luminance degradation determination part 150 compares the target luminance La and the detected luminance Lb to determine a degree of degradation of an OLED element and generates the luminance control signal CTL1 so that the detected luminance Lb approximates to the target luminance La.
    輝度劣化判定部150は目標輝度Laと検出輝度Lbとを比較してOLED素子の劣化の程度を判定し、検出輝度Lbが目標輝度Laに近づくように輝度制御信号CTL1を生成する。 - 特許庁
  • The control signals CTL1-8b are outputted to buffers OB1-8, a singlar buffer is selected from the buffers B1-B8 and is set as a High-Z state, and the non-selected buffer is set as a non-High-Z state.
    制御信号CTL1〜8bをバッファOB1〜8に出力して、バッファOB1〜8のうち単数のバッファを選択してHigh−Zステートとし、選択していないバッファをnon−High−Zステートとする。 - 特許庁
  • The controller CTL1 judges the charging voltage of the capacitor CP1 based on an increase in the detected voltage by the voltage sensor during predetermined counting time by the counter, and controls the charging voltage by the charger PSU1 based on this judgment.
    制御部CTL1は、カウンタによる所定のカウント時間中における電圧センサによる検出電圧の増加に基づいてキャパシタCP1の充電電圧を判定し、この判定に基づいて充電器PSU1による充電電圧を制御する。 - 特許庁
  • A bias circuit 3a has a bias current control circuit 30 which controls supply and interruption of a bias current in response to the signal CTL1, a current source circuit 31, and a circuit current control circuit 32 which controls supply and interruption of a current by the circuit 31 in response to the signal CTL2.
    バイアス回路3aは、バイアス電流の供給と遮断を信号CTL1に応じて制御するバイアス電流制御回路30と、電流源回路31と、回路31による電流の供給と遮断を信号CTL2に応じて制御する回路電流制御回路32とを有する。 - 特許庁
  • The air-conditioning control part 44 executes operation and stop of the air conditioner according to air-conditioning requests (CTL1 and CTL2), and controls air conditioner to limit the operation of the air conditioner when the integrating result reaches a limit value for limiting discharge of the power storage device during the operation of the air conditioner.
    空調制御部44は、空調要求(CTL1,CTL2)に応じて、空調装置の動作および停止を実行するとともに、空調装置の動作中に積算結果が蓄電装置の放電を制限するための制限値に達した場合には、空調装置の動作が制限されるように空調装置を制御する。 - 特許庁
  • The equipment is provided with a control means CTL2 controlling the amount of the secondary fuel to be fed based on the outlet temperature of the mixed combustion furnace 2, and a safety means CTL1 reducing the amount of heat to the recycling furnace 1 when the outlet temperature of the mixed combustion furnace 2 exceeds a first standard value decided in accordance with the combustion capacity of the mixed combustion furnace 2.
    混焼炉2の出口温度に基づいて二次燃料の供給量を調整する調整手段CTL2と、混焼炉2の出口温度が、混焼炉2の燃焼能力に対応して決定されている第一基準値を越えたとき、リサイクル炉1への加熱量を減少させる安全手段CTL1とを備える。 - 特許庁
  • A modulation circuit 1 has a gate circuit 10 which controls supply and interruption of a modulation current in response to a burst circuit control signal CTL1, current source circuits 14-17, and a circuit current control circuit 18 which controls supply and interruption of a current by the circuits 14-17 in response to a current source circuit control signal CTL2.
    変調回路1は、変調電流の供給と遮断をバースト回路制御信号CTL1に応じて制御するゲート回路10と、電流源回路14〜17と、回路14〜17による電流の供給と遮断を電流源回路制御信号CTL2に応じて制御する回路電流制御回路18とを有する。 - 特許庁

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.