The semiconductor device has a non-volatile memory cell including a write transistor which includes an oxide semiconductor and has small leakage current in an off state between a source and a drain, a read transistor including a semiconductor material different from that of the write transistor, and a capacitor. 酸化物半導体を用い、オフ状態でのソースとドレイン間のリーク電流(オフ電流)が少ない書き込み用トランジスタ、該書き込み用トランジスタと異なる半導体材料を用いた読み出し用トランジスタ及び容量素子を含む不揮発性のメモリセルを有する半導体装置を提供する。 - 特許庁
The light source device 1 includes: a lamp 3 for generating ozone from the oxygen of surrounding atmosphere by containing ultraviolet in radiation wavelength; and a fan 11 for generating a current of air into spaces 13 and 15 for removing ozone generated in lamp arrangement spaces 13 and 15 in which the lamp 3 is arranged. 光源装置1は、放射波長に紫外線を含んで周辺雰囲気の酸素からオゾンを発生させるランプ3と、ランプ3が配置されるランプ配置空間13,15で発生したオゾンを空間13,15から除去するために空間13,15内に風を送るためのファン11を備えている。 - 特許庁
A phase compensation characteristics control circuit 16 changes its multiplying factor, by varying the tail current of a voltage control power source constituting the multiplier 15, or changes it by varying a resistance value by its gate potential, when a resistor is constituted by an MOS-FET. 位相補償特性制御回路16は、キャパシタンスマルチプライヤ15を構成する電圧制御電流源のテール電流を変化させることにより倍率を変更し、あるいは、抵抗がMOS−FETで構成される場合、そのゲート電位により抵抗値を変化させることによって倍率を変更する。 - 特許庁
To provide a planar ferrite core that shortens the total length of a coil, reduces Joule heat caused by the flow of a current, mounts electronic devices in a free area resulting from by coil miniaturization, and achieves power source miniaturization and high density. コイルの総延長距離を短くすることが可能であり、流れる電流によって生じるジュール熱の低減と、コイルの小型化によって生じる面積部分に電子部品の実装を可能とし、電源の小型化および高密度かが可能なプレーナー型フェライトコアを提供すること。 - 特許庁
I will quote a statement made by the Prime Minister: "The source of trust in the state and society is a sense of safety. In light of the people's concern about and dissatisfaction with the current status of social security, it is necessary to quickly carry out meticulously-thought-out measures that foster a sense of safety and reflect the people's viewpoints.
総理からは、「国家や社会に対する信頼の源は安心であり、今日の社会保障の現状に対して国民が抱く不安や不満を踏まえ、安心につながる、国民の目線に立ったきめ細かな対策を速やかに実行に移していく必要がある。 - 金融庁
The power factor of total electric heater is improved by managing N units of electric heaters as a group by a central processing device and a power source control device, and by controlling the load and volume of the alternating current flowing through the electric heaters so that the phase angle of respective electric heater becomes continuous with each other. 中央処理装置と制御用電源装置とによってN個の電熱ヒータを群管理して、これら電熱ヒータに流れる交流電流の負荷と制御量とを、各電熱ヒータ相互の位相角が連続するように制御して、電熱ヒータ全体の力率を改善させるようにする。 - 特許庁
The liquid food heating device 1 is composed of a coil 7 connected with an alternate current power source 14, a case 8 with the coil wound, a metal body 9 to be a heat-radiating body fitted inside the case 8, and paths 4, 5 connected in front and at the rear of the case 8 for liquid food to pass through. 液状食品加熱装置1は、交流電源14に接続されたコイル7と、コイル7が巻かれたケース8と、ケース8内に設置された発熱体となる金属体9と、ケース8の前後に接続された、液状食品が通過する通路4・5とで構成される。 - 特許庁
To prevent a propagation of a high frequency noise due to a high frequency current to a power source line, in a discharge lamp lighting unit in which: two discharge lamps are serially connected; and two output line lead portions corresponding to each of the discharge lamps are arranged in a facing side of a printed circuit board. 2灯の放電灯が直列接続され、かつ、各放電灯に対応した2つの出力線口出し部がプリント配線基板の対辺に配置される放電灯点灯装置において、高周波電流に伴う高周波ノイズの電源ラインへの伝搬を防止する。 - 特許庁
In the backlight device, a heating component heating at a calorific value equivalent to that of an LED is arranged at a position close to the LED in each LED block, and either the LED or the heating component is continuously energized with a PWM control signal by means of a common constant current source. 各LEDブロックにおいてLEDに近接した位置にLEDと同等の発熱量で発熱する発熱部品を配置し、PWM制御信号でLEDと発熱部品のいずれか一方が、共通の定電流源により常時通電されるように構成することを特徴とする。 - 特許庁
The charging equipment 80 is composed of a three-phase power source 1, rectifying elements 2-7, a current limiting resistor 9, a smoothing capacitor 8, a switch 10, an instantaneous power failure signal generator 55, a reference voltage value setter 56, a first comparator 54, a first control circuit 70, and a second control circuit 71. 充電装置80は、3相の交流電源1、整流素子2〜7、限流抵抗9、平滑コンデンサ8、スイッチ10、瞬時停電信号発生器55、基準電圧値設定器56、第1の比較器54、第1の制御回路70、および第2の制御回路71から構成されている。 - 特許庁
When the AND circuit 4 is at the low level on the output, a current flows on the route from the power source to the output of the AND circuit 4 via the pull-up resistor group, and the switch set on, while the levels on the first ends of the switches S1-S8 are inputted to the CPU 2 via a gate circuit 8 and a data bus 7. アンド回路4の出力がローレベルになると、「電源→プルアップ抵抗群→オンに設定されているスイッチ→アンド回路4の出力側」の経路で電流が流れ、その時のスイッチS1〜S8の一端のレベルがゲート回路8とデータバス7を通ってCPU2に入力される。 - 特許庁
The cooling heating device performs cooling and heating of the interior of a room such that the direction of a current flowing to the Peltier element 10 is controlled by a power source 40 and heat is moved from the plate 20 in the heat discharging absorbing chamber to the heat discharging apparatus 30 and from the heat discharging apparatus 30 to the plate 20 in the heat discharging absorbing chamber. 冷暖房装置は、電源40がペルチェ素子10に流す電流の方向を制御して、放熱吸熱室内プレート20から排熱器30に、または排熱器30から放熱吸熱室内プレート20に熱を移動させて、室内を冷房または暖房する。 - 特許庁
The electric furnace for ceramic art is a furnace for ceramic art which is used by connecting to a power source in the home, and provided with a furnace 1 having a hot wire 10 inside as the heater, a temperature sensor 25 detecting the temperature inside the furnace, a temperature control device 15, and a current control device 17. この陶芸用電気窯は、家庭用の電源に接続されて使用される陶芸用の窯であって、内部に熱線10としてのヒータを有する炉1と、炉内部の温度を検出する温度センサ25と、温度制御装置15と、電流制御装置17とを備えている。 - 特許庁
Furthermore, an inductor L1 is coupled to the first fuse F1, the force-commutated synchronous rectifier S1 and the low side switch Q1, and a second fuse F2 is coupled to the inductor L1 and is operable to be coupled to a current source and to open in response to a second fault. さらに、インダクタL1が、第1のヒューズF1、強制転流式の同期整流器S1、およびローサイドスイッチQ1に結合され、また第2のヒューズF2が、インダクタL1に結合されて、電流源に結合されるように、かつ第2の障害に応答して開くように、動作可能である。 - 特許庁
In this method, a heat exchanger made of an Ni based corrosion resistant alloy containing ≥50 mass% Ni and placed in a high concentration hydrochloric acid environment is use as a cathode, and resin-impregnated carbon is used as an anode, to feed electric current between the anode and the cathode by an external power source. 高濃度塩酸環境下に置かれたNi:50質量%以上含むNi基耐食合金で構成された熱交換器を陰極とし、樹脂含浸炭素を陽極として陽陰極間に外部電源により電流を供給することを特徴とする。 - 特許庁
To provide an engine ignition device for performing the continuous current carrying avoiding control for forcibly stopping the ignition output from a power source in order to prevent the breakdown of an ignition coil to be a cause of the misfire of an engine, and provide a gas heat pump type air conditioner provided with this engine ignition device. エンジン失火を生じさせるイグニッションコイルの破壊を防ぐために、電源からの点火出力を強制停止させる連続通電回避制御を行うエンジン点火装置、及びこのエンジン点火装置を備えたガスヒートポンプ式空気調和機を提供すること。 - 特許庁
A DC power supply source having a power storage system with a capacity to process the current flowing into or out of the inverter is inserted in series to the ground side of the input of the inverter and the output voltage thereof is continuously controlled from zero to be added to the trolley voltage, which is then applied to the inverter. インバータの入力の接地側に、インバータに流入もしくは流出する電流を処理可能な容量の蓄電装置を有する直流電圧源を直列に挿入し、この出力電圧をゼロから連続的に制御して架線電圧に加算してインバータに印加する。 - 特許庁
The thermal printer has a thermal head 6, a constant current driving type motor for carrying paper, and a power source circuit 3 for impressing a voltage V1 regulated according to printing information to the thermal head 6 and the motor 8 in a printing state, and impressing a fixed voltage V2 for carrying to the motor 8 in a non-printing state. サーマルヘッド6と、用紙を搬送するための定電流駆動方式のモータと、印刷時に、印刷情報に応じて調節された電圧V1をサーマルヘッド6及びモータ8に印加し、非印刷時に、搬送用の固定電圧V2をモータ8に印加する電源回路3とを有する。 - 特許庁
This light source device 1 is equipped with an electrodeless discharge lamp 2 which discharges and emits light by passing a high frequency current, and an optical integrator 3 including a first and second lens arrays 21, 22, and a PS converter 8 including a conductive reflecting film 8d are disposed on the opening part 6a side in a casing part 5. 光源装置1は、高周波電流を流すことで放電発光する無電極放電ランプ2を備えており、筐体部5内における開口部6a側に、第1・第2レンズアレイ21,22を含む光インテグレータ3、導電性の反射膜8dを含むPSコンバータ8、等を配置している。 - 特許庁
The sizes of the transistors M1 and M2 constituting the differential pair and the transistors P1 and P2 for the load are appropriately designed, the transistors M1 and M2 are provided with a bypass current source as the need arises, the common mode gain can thereby be suppressed, and a filter circuit that has high linearity and is stable can be realized. 差動対をなすトランジスタM1,M2及び負荷用トランジスタP1,P2のサイズを適宜設計し、また必要に応じてトランジスタM1,M2にバイパス電流源を設けることによって同相ゲインを抑制でき、線形性がよくかつ安定したフィルタ回路を実現できる。 - 特許庁
To provide a safety enclosed compressor free from the increase of the leaked current even in inverter driving using a power source of high frequency, and using a refrigerant mainly composed of R32 of low insulating performance, and free from the electrical leak and the possibility of the electric shock, and to provide a refrigerating cycle device using the compressor. 高周波電源を使用するインバータ駆動や絶縁性能の低いR32を主成分とした冷媒を使用しても、漏れ電流の増加が無く、漏電や感電の恐れの少ない安全な密閉型圧縮機及びこれを使用した冷凍サイクル装置を提供すること。 - 特許庁
This water-purifying device D of a culture pond 1 comprises a water-receiving tank 2, a decoloration tank 3, a filtration tank 10, a precipitation tank 8, a pair of electrodes 4, 4, a direct electric source (not drawn) for supplying an electric current to the electrodes 4, 4, an incurrent pipe 6, a circulation pump 7, and an excurrent pipe 12. 養殖池1の水浄化装置Dは、水収納槽2、脱色槽3、濾過槽10、沈殿槽8、一組の電極4・4、電極4・4に電流を供給するための直流電源(図示略)、流入管6、循環ポンプ7、流出管12を備えてなる。 - 特許庁
At the same time, when a control signal ϕ3 is made 'H', a transistor Q3 is made on, the voltage which is almost doubly boosted is supplied to the light emitting diodes LW1, LB1 and LG1 and, on the other hand, the source voltage is directly supplied to LR1, an electric current flows through all the diodes and the light emitting thereof occurs. それと同時に、制御信号φ3を“H”とすると、トランジスタQ3がオンとなり、ほぼ2倍に昇圧された電圧が発光ダイオードLW1、LB1、LG1に供給され、一方電源電圧が直接LR1に供給され、共に電流が流れて発光する。 - 特許庁
When a bit line BL is defective due to short-circuiting to the line of the ground potential GND, the P-channel MOS transistor 34 is made non-conductive, the current is prevented from leaking from the line of a power source potential VCC to the line of the ground potential GND through the defective bit line BL. ビット線BLが接地電位GNDのラインにショートした不良ビット線である場合は、PチャネルMOSトランジスタ34は非導通になり、電源電位VCCのラインから不良ビット線BLを介して接地電位GNDのラインに電流がリークすることが防止される。 - 特許庁
When the transfer voltage of the transfer device for yellow 40Y is decided, for example, the transfer roller 42Y of the transfer device 40Y is connected to a constant current power source 43Y and the transfer rollers 42M-42K of the other transfer devices 40M-40K are set in a floating state. 例えば、イエロー用の転写装置40Yにおける転写電圧を決定する場合には、転写装置40Yの転写ローラ42Yを定電流電源部43Yに接続し、他の転写装置40M〜40Kの転写ローラ42M〜42Kはフロートの状態にしておく。 - 特許庁
Power is supplied from a power source 700 on the side of the Pachinko game machine to the side of the card treatment machine so that a direct current rectified by a rectifier on the side of the card treatment machine causes the operation of a ball lending acceptance display 48d, a ball lending button 44c, a return button 42c, and switching circuits 710, 712. パチンコ遊技機側の電源700からカード処理機側へ電力が供給され、カード処理機側の整流器によって整流された直流電流によって、玉貸可表示器48d、玉貸ボタン44c、返却ボタン42c、スイッチ回路710,712が動作する。 - 特許庁
To provide an organic semiconductor thin-film transistor and a manufacturing method for the organic semiconductor thin-film transistor in which pentacene crystal axis misalignment at the source electrode end and the drain electrode end, which is an essential problem of an organic semiconductor thin-film transistor of a bottom gate/bottom contact type, is eliminated and hole current can be increased. ボトムゲート・ボトムコンタクト型の有機半導体薄膜トランジスタの本質的な課題であるソース電極端、ドレーン電極端でのペンタセン結晶軸不整合を解消し、正孔電流を増加させることのできる有機半導体薄膜トランジスタおよびその製造方法を得る。 - 特許庁
An information display device 10 is provided with a switching part 200 which switches, in a given cycle, between a state where a display panel driving power source 240 is connected to an electrode part and a state where a detection voltage and current generator 210 and a detector 220 are connected to the electrode part, using a controller 230. 情報表示装置10は、コントローラ230により表示パネル駆動電源240が電極部に接続された状態と、検出電圧/電流発生器210及び検出器220が電極部に接続された状態とを、所定の周期で切り替える切替部200を備える。 - 特許庁
Moreover, in ratios among currents (INA and INB) of constant current sources and sizes (WPA and WPB) of respective transistors of respective power source, the ratio (WPA/INA) in the VDLA is set to be smaller than the ratio (WPB/INB) in the VDLB. さらには、各電源回路の定電流源の電流(INAとINB)と各出力トランジスタのサイズ(WPAとWPB)との比率において、第1電源回路(VDLA)での比率(WPA/INA)を、第2電源回路(VDLB)での比率(WPB/INB)より小さく設定する。 - 特許庁
A judging part 16 stores in advance a spectrum reference value Po as a power limit value of the basic wave and judges the static power source current as abnormal if the power Pf exceeds the spectrum reference value Po or judges as normal and outputs the judged result to a CPU 11. 判定部16はこの基本波のパワー限界値たるスペクトル参照値Poを予め記憶しており、パワーPfがスペクトル参照値Poを越えていれば静止電源電流が異常と判定し、さもなければ正常と判定してその判定結果をCPU11へ出力する。 - 特許庁
To make a current collector small in size and improved in transmission efficiency and to prevent occurrence of errors and malfunctions on a rotation control by simplifying a power transmission from a rotary drive source. 回転駆動源からの動力伝達を単純化することにより小型化と伝動効率の向上を図るとともに、回転制御上の誤差・誤動作の発生を防止できる遊技機用回転摺接式集電装置と、それを用いた遊技機用配線基板の回転構造を提供する。 - 特許庁
A monitoring means 11 operating while using a protection current by a galvanic anode system as a power source is provided at a location where an operating state of the monitoring means can be checked from the ground, and a cathodic protection effect is monitored by checking the operating state of the monitoring means 11 from the ground. 流電陽極方式による防食電流を電源として作動する監視手段11を、その作動状態が地上から確認できる位置に設け、監視手段11の作動状態を地上から確認することにより電気防食効果を監視する。 - 特許庁
While, when end-to-end voltage of the capacitor 86 increases since the electric charge gathers in the capacitor 86, the transistor 85 is turned on, and the voltage outputted to the operational amplifier 7 from the tube electric current setting part 8 becomes a value V2 by dividing the source voltage by the resistance 81 and the resistance 82. 一方、コンデンサ86に電荷が溜まってコンデンサ86の両端の電圧が上昇すると、トランジスタ85がオンとなり、管電流設定部8から演算増幅器7へ出力される電圧は、抵抗81と抵抗82とで電源電圧を分圧した値V2となる。 - 特許庁
To provide a thermoelement of light weight in which installation to a heat source etc. which has unevenness on the surface is easy, processing is easy, neither rare element nor toxic element is necessarily included, practically sufficient voltage and/or practically sufficient current are securable, and which is tough to vibration and thermal stress. その表面に凹凸がある熱源等への設置が容易であり、軽量かつ加工が容易で、希少元素や毒性元素を必ずしも含まず、実用上十分な電圧及び/又は電流を確保することができ、振動や熱応力に対して強い熱電素子を提供すること。 - 特許庁
Also, the control part 20 creates an intermediate interphase voltage of the load side interphase voltages Vuv, Vvw, Vwu by controlling the bidirectional switch for connecting a phase for making the voltage to the intermediate interphase voltage and a phase, in which an intermediate interphase voltage of the alternating current power source side interphase voltages Vrs, Vst, Vtr. また、制御部20は、負荷側相間電圧Vuv,Vvw,Vwuのうち中間の相間電圧を、当該中間の相間電圧にする相と交流電源側相間電圧Vrs,Vst,Vtrのうち中間の相間電圧が入力される相との接続を行う双方向スイッチを制御して生成する。 - 特許庁
As a result, since the voltage obtained by adding the potential difference (Ie×Re) and the output voltage Va of the acceleration voltage power source 9 becomes the actually intended acceleration voltage to be impressed on the electron gun, the emission current can be measured correctly, without exerting effects of the voltage drop on the acceleration voltage. これにより、電位差(Ie×Re)と加速電圧電源9の出力電圧Vaを加算した電圧が実際の電子銃に印加される所望の加速電圧となるので、加速電圧に電圧降下の影響を及ぼすことなくエミッション電流を正しく計測できる。 - 特許庁
When the level detecting signal is greater than a reference signal of a reference signal source 26, on the basis of a switching signal from a comparator 24, the driver section 8 brings the gain control section 6 into the attenuated state, and the driver section 14 increases the operating current of the high frequency amplification stage 10, 12. レベル検出信号が基準信号源26の基準信号よりも大きいとき、比較器24からの切換信号に基づいてドライバ部8がゲインコントロール部6を減衰状態とし、ドライバ部14が高周波増幅段10、12の動作電流を増加させる。 - 特許庁
When the DC voltage is not applied from the power source 100 due to the power interruption or the like and supply of the current from the circuit 150 to the circuit 103 is stopped, the power is automatically supplied from the cell 151 to the circuit 103 via a diode D2. 停電等により制御回路用電源100からDC電圧が印加されず、充電回路150からLEDドライブ回路103への電流の供給が停止すると、自動的に二次電池151からダイオードD2を介してLEDドライブ回路103へ電力が供給される。 - 特許庁
A semiconductor device includes a power source line 4, a ground line 6, a signal line 5 for transmitting signals, a signal pad 2 connected to the signal line 5, a thyristor 7 provided between the signal line 5 and the ground line 6, and a trigger circuit 8 for passing a trigger current I_trigger to the thyristor 7. 半導体装置が、電源線4と、接地線6と、信号を伝送する信号線5と、信号線5に接続された信号パッド2と、信号線5と接地線6との間に設けられたサイリスタ7と、サイリスタ7にトリガ電流I_triggerを流すためのトリガ回路8とを具備する。 - 特許庁
The semiconductor device includes a first pad 1 for current source connection, a via chain which has one end connected to the first pad 1 and the other end connected to a substrate 20 via a diffusion layer 21 of the same conductivity type as the substrate 20, and a second pad 2 and a third pad 3 for voltage measurement. 本発明による半導体装置は、電流源接続用の第1パッド1と、一端が、第1パッド1に接続され、他端が、基板20と同じ導電型の拡散層21を介して基板20に接続されたヴィアチェーンと、電圧測定用の第2パッド2及び第3パッド3とを具備する。 - 特許庁
To reduce dispersion and change with time of characteristics of an emission current to a drive voltage for each electron source, in a display device in which a plurality of electron sources utilizing field emission or the like is arranged in a matrix form and the electrons from the electron sources are made to radiate against a fluorescent material to emit light. 電界放出等を利用した複数の電子源をマトリクス状に配列し、該電子源からの電子を蛍光体に射突させて発光させる表示装置において、その駆動電圧対エミッション電流特性の電子源毎のばらつき及び経時変化を低減する。 - 特許庁
In this invention, the fluctuation of the distance on welding between the tip and the welded article is detected by the change of current detecting signal Iwa, depending on this change value, the electrical source for welding corrects the setup signal ηs for short-circuit time rate previously established to control output voltage Vo. 本発明は、溶接中のチップ・被溶接物間距離の変動を電流検出信号Iwaの変化によって検出して、その変化値に応じて予め設定した短絡時間率設定信号ηsを修正して出力電圧Voを制御する溶接電源装置である。 - 特許庁
Meanwhile, the potential difference between the substrate 3 and negative electrode 4 is detected by a voltage detecting element 11, and the current source 6 is turned off by a control part 12 when the potential difference detected by the element 11 begins to decrease to finish the anodization. また、電圧検出部11は、n形単結晶シリコン基板3と負極4との間の電位差を検出し、制御部12は、電圧検出部11により検出した電位差が低下し始めた時点で電流源6をオフさせることにより陽極酸化を終了させる。 - 特許庁
In the lighting device 100 having the organic EL element 10 as a light source, a plurality of organic EL element regions 10a, 10b formed on an identical substrate and a driving means 20 which supplies a forward current one by one for each organic EL element region are provided. 有機EL素子10を光源とする照明装置100において、同一基板上に形成された複数の有機EL素子領域10a、10bと、各有機EL素子領域10a、10b毎に、順次、順方向電流を供給する駆動手段20と、を設ける。 - 特許庁
The optical disk device is provided with a laser diode 1, a monitor diode 2 for detecting its light emission amount, a switch for switching electricity to the monitor diode 2 to constant current source 4 and a temperature measuring part 7 for measuring a temperature based on a voltage detected from the monitor diode 2 before the operation of an optical pickup. レーザダイオード1と、その発光量を検出するモニタダイオード2と、モニタダイオード2への通電を定電流源4に切り換える切換スイッチ8と、光ピックアップの動作前に、モニタダイオード2から検出される電圧に基づいて、温度を計測する温度計測部7を有する。 - 特許庁
The image display device 10 includes a light source lamp 23 for expanding and projecting an input image to outside; an instantaneous power cutoff detecting section 22 for outputting a detection signal, by detecting instantaneous cutoff of commercial alternating current input power; and a supply power adjusting section 13. 画像表示装置10を、入力画像を外部に拡大投射するための光源ランプ23と、商用交流入力電力の瞬断を検知して、その検知信号を出力する瞬断検出部22と、供給電力調整部13とを備える構成にする。 - 特許庁
A control portion of the current control portion 11 indicates abnormality of the communication portion 7 through visible light communication such that when a failure in reception of the control signal by the communication portion 9 is recognized, the light circuit is controlled to blink the light source 7 in short cycles enough not to feel the blinking with the human's eyes. 電流制御部11の制御部は、通信部9による制御信号の受信ができないことを認知したときに、点灯回路を制御して光源7を人の目には感じない短い周期で点滅させる可視光通信により、通信部7の異常を報知する。 - 特許庁
An abnormal current is detected by a transformer 14 coupling a primary winding wire 14a, disposed between speakers 6, 6_1-6_7, from output amplifiers 3, 3_1-3_7 to a high frequency coil 14b inside a switching power source circuit 18, and the speakers and the output amplifiers are protected via a CPU 22. スイッチング電源回路18内の高周波コイル14bに出力増幅器3、3_1〜3_7からスピーカ6、6_1〜6_7間に配した1次巻線14aをカップリングさせたトランス14によって異常電流を検出し、CPU22を介してスピーカ及び出力増幅器のプロテクトを行う。 - 特許庁
As the superheated steam generator 300, a superheated steam generator of electromagnetic induction type equipped with a tank inside of which a member comprising a ceramic material is installed and through which the steam passes with contacting to the member and a coil installed outside of the super heated tank and connected to a high frequency alternate current power source is used. また、過熱蒸気発生装置300として、内部に磁性体からなる部材を配置し、蒸気がこの部材と接触しながら通過するタンクと、この過熱タンクの外側に高周波交流電源に接続したコイルとを備えた電磁誘導方式の過熱蒸気発生装置を用いる。 - 特許庁
The plating apparatus has a plurality of plating tanks 414a, 414b and 414c, and the plated film is formed on a surface of a substrate sequentially in different plating tanks, while a single plating power source 416 passes an electric current between the substrate and an anode of the plating tank in which the substrate has been stored. 複数のめっき槽414a,414b,414cを備え、基板の表面に異なるめっき槽で順次めっきを行うめっき装置において、基板と該基板が入れられためっき槽のアノードとの間で単一のめっき電源416から通電してめっきを行う。 - 特許庁