To provide a current output type DA converter which enables to reduce a placement location dependency of a current source and to output analog signals corresponding to the number of added current power supplies with stability. 電流源の配置場所依存性を軽減し、安定して加算された電流源の数に対応してアナログ信号を出力することのできる電流出力型DAコンバータを構成するものである。 - 特許庁
The detecting element is arranged inside a current passage between the current or voltage source and the one or more ignition element terminals, or arranged adjacent to the current passage. この検出素子は、上記電流または電圧源と上記少なくとも1つの点火素子端子との間の電流路内に配置されているか、あるいはその電流路に隣接して配置されている。 - 特許庁
The two transistors Q3, Q4 constituting the current source 100 are cascode-connected to reduce the effect of fluctuations in a power supply VCC on the current flowing through the current mirror circuit 200. 電流源100を構成する2つのトランジスタQ3,Q4をカスコード接続で構成することで、カレントミラー回路200に流れる電流に対する電源VCCの変動の影響を小さくする。 - 特許庁
To provide a method and a device for programming a non-volatile memory cell of which a current value of a current flowing in a cell is controlled through a current limiter coupled to a source node of a memory cell. セルの中を流れる電流の電流値が、メモリーセルのソース・ノードに結合した電流リミッターを通して制御される不揮発性メモリー・セルをプログラムするための方法と装置を提供する。 - 特許庁
The current-voltage conversion circuit 101 included in the light reception amplifier circuit 100 is provided with a current input section 104 and a current output section 105, and can be operated at a relatively low power-source voltage. 受光アンプ回路100に含まれる電流電圧変換回路101は、電流入力部104、電流出力部105を備えているので、比較的低い電源電圧で動作可能である。 - 特許庁
When a load is connected, a load current rises sharply, and an output voltage VOUT drops, the comparator 4 outputs a current boost signal SB1 indicating this effect to the current source 5. コンパレータ4は、負荷が接続されて負荷電流が急激に立ち上がって出力電圧VOUTが低下すると、その旨を示す電流ブースト信号SB1を可変電流源5に出力する。 - 特許庁
To provide a current detection circuit of a transformer capable of detecting a current in sufficient precision and achieving miniaturization of a power source circuit without using the transformer having a large current capacity. 電流容量の大きな変流器を用いることなく、十分な精度で電流を検出することができ、また電源回路の小形化を図ることができる変圧器の電流検出回路を提供する。 - 特許庁
The current mirror circuit CM1 allows a current corresponding to a current inputted from the output of the inverter circuit INV2 via the first resistor R1 to flow from a source of the level shift circuit MOS1 to a ground point. カレントミラー回路CM1は、第1の抵抗R1を介してインバータ回路INV2の出力から入力した電流に対応する電流をレベルシフト素子MOS1のソースから接地点に流す。 - 特許庁
At the time of recording at a lower speed than the maximum speed, a current source 2 controls for a specific period a current amount to drive the described recording head during the reversal of the current direction. 電流源2は、最高速度よりも低い速度で記録を行う場合には、電流方向逆転時に前記記録ヘッドに電流を駆動するための電流量を一定時間だけ抑制する。 - 特許庁
And a voltage supply circuit 7 which supplies electric voltage to the primary circuit of each starter circuit from the direct current power source 3 or the direct current-alternating current converting circuit 4 is made a common circuit for all the starter circuits. そして、直流電源回路3又は直流−交流変換回路4から各起動回路の1次側回路に対して電圧供給を行う電圧供給回路7を同じ回路とした。 - 特許庁
When a set current Im is supplied to the driving transistor T1 through a data line 15 by a current source 434, a voltage having a magnitude corresponding to the set current Im is stored in a holding capacitance element Ch. 電流源434がデータ線15を介して駆動トランジスタT1に設定電流Imを供給すると設定電流Imに応じた大きさの電圧が保持容量素子Chに記憶される。 - 特許庁
This discharge lamp lighting device boosts the input voltage from a direct current power source 1 by a direct current booster circuit 3, and converts to the alternating current by a DC-AC inverter 4 to supply the lighting power to a discharge lamp 6. 直流電源1からの入力電圧を直流昇圧回路3により昇圧し、DC−ACインバータ4により交流に変換して放電ランプ6に点灯電力を供給する。 - 特許庁
One of a plurality of correction current profiles is selected on the basis of the set light quantity, and an electric current, which is corrected on the basis of the selected correction current profile, is supplied to a light source. この設定された光量に基づいて、複数の補正電流プロファイルのうちの1つを選択し、当該選択した補正電流プロファイルに基づいた補正を行った電流を光源に供給する。 - 特許庁
To provide a power source unit, a method of electrification, an electri fying device, and an image forming device wherein a current value control method of a constant current method is used which is advantageous in cost and can accurately control the current. 精度よく電流制御し、コスト的にも有利な定電流方法の電流値制御方法を用いた、電源装置、帯電方法、帯電装置および画像形成装置を提供する。 - 特許庁
To provide a fixed current circuit capable of reducing the output currents of a current source generated due to the fluctuation of a threshold and a module including this fixed current circuit and a transmitter and a receiver. しきい値のばらつきによって発生する電流源の出力電流の変動を抑えることのできる定電流回路及びこれを含むモジュール並びに送信装置及び受信装置を提供する。 - 特許庁
In order to improve the current source 12 regarding the quality of the output signal, the controllable current source 12 further includes replicas T1', T2' of the current routes T1, T2 in a non-control state and a replica output terminal Kout' thereof is connected to the output terminal Kout through current mirrors T5-T8. 出力信号の品質に関して電流源12を改良するために、制御可能な電流源12は、更に、非制御状態における電流経路T1,T2のレプリカT1′,T2′を有しており、そのレプリカ出力端子Kout′はカレントミラーT5乃至T8を介して出力端子Koutへ接続している。 - 特許庁
To enable a mean current as a current command value of an uninterruptible power source during a parallel operation to be double calculated and checked each other, and to enable the mean current of a direct power supply circuit and mean current when the uninterruptible power source of a stand-by state is operated in parallel to be calculated. 並列運転中の無停電電源装置の電流指令値となる平均電流を二重に算出して相互チェックを可能にすると共に、直送給電回路の平均電流と、スタンパイ状態にある無停電電源装置が並列運転する際の平均電流が算出できるようにすることにある。 - 特許庁
Therefore, since the exciting current of the coil for electromagnetic stirring becomes a superimposed current with the high frequency current supplied from the high frequency electric source device and the low frequency current supplied from the low frequency electric source device, the outside ridge part and the center part of the electric conductive molten material are efficiently stirred. 従って、電磁攪拌用コイルの励磁電流は高周波数電源装置から供給される高周波数電流と低周波数電源装置から供給される低周波数電流とが重畳された電流となるため、導電性溶融物の外縁部および中心部が効率よく攪拌される。 - 特許庁
That is, since an input current Iin is drawn from the power source AC in the period T3, the part of a load current IL_1 can be used also as the input current Iin, and the harmonic distortion can be reduced by decreasing the level of the input current Iin at the zero-crossing point of a power source voltage Vs. すなわち、期間T3においてのみ交流電源ACから入力電流Iinを引き込むため、負荷電流I_L1の一部を入力電流Iinと兼用することが可能であり、電源電圧Vsのゼロクロス点における入力電流Iinのレベルを低減して高調波歪を低減することができる。 - 特許庁
The size of a constant current I4 formed by the constant current source circuit 7 is changed corresponding to an output voltage VOUT by feeding back the output voltage VOU, and when the output voltage VOUT is small, the constant current source circuit 7 is turned OFF to reduce the constant current I4 to zero. 出力電圧VOUTをフィードバックすることで定電流源回路7が形成する定電流I4の大きさを出力電圧VOUTに応じて変化させるようにし、出力電圧VOUTが小さい場合には、定電流源回路7をOFFさせて定電流I4がゼロとなるようにする。 - 特許庁
When a current supplied to a power amplifier 13 from a first power source Vcc1 exceeds a second maximum current Ix which is lower than a first maximum current Imax by a margin current m, an overcurrent detecting circuit 11 turns off a power FET 12 to stop the supply of the first DC power source Vcc1 to the power amplifier 13. 第1電源部Vcc1からパワーアンプ13に供給される電流が第1最大電流Imaxよりマージン電流mだけ低い第2最大電流Ixを超えるとき、過電流検出回路11がパワーFET12をオフしてパワーアンプ13への第1直流電源Vcc1の供給を停止させる。 - 特許庁
This structure reduces leakage current from the rear surface of the chip, reduces on-resistance, reduces loop current between a gate and a source, and reduces parasitic inductance at a source wiring side, thereby preventing oscillation of a gate voltage via parasitic capacitance between the gate and the source. これにより、チップ裏面からのリーク電流を減らし、オン抵抗を低減するとともに、ゲート−ソース間のループ電流を減らし、ソース配線側の寄生インダクタンスを低減することで、ゲート−ソース間の寄生容量を介したゲート電圧の発振を抑制する。 - 特許庁
As the first power source 17a and second power source 17b of the power source part 17, the constant current of 50μA is supplied and the one having a voltage limit function for performing limitation so as not to output current having voltage higher than 50V is used respectively. 電源部17の第1電源17a及び第2電源17bとして、50μAの定電流を供給し、しかも、それぞれ50Vより高い電圧を有する電流が出力されないように制限する電圧リミット機能を有するものを使用する。 - 特許庁
A source and a gate of a transistor(TR) T3 are connected to each other, and the source and gate of a Tr T3 are connected respectively to the source and drain of an output current side TR T2 of a conventional current mirror circuit consisting of the two TRs T1, T2 whose gates and drains are short-circuited. ゲート及びソースをそれぞれ互いに接続し、一方はさらにゲートとドレインとを短絡した二個のトランジスタT1,T2からなる従来のカレントミラー回路の出力電流側トランジスタT2のソース、ドレインに、トランジスタT3のソース、ゲートをそれぞれ接続する。 - 特許庁
To provide an EL display device capable of obtaining a bright display by supplying a current which is to be intrinsically supplied to EL element while suppressing a lowering of power source current due to resistance of driving power source line which is caused by distance from a driving power source input terminal. 駆動電源入力端子からの距離に起因する駆動電源線の抵抗による電源電流の低下を抑制し、本来供給されるべき電流がEL素子に供給して、明るい表示を得ることができるEL表示装置を提供する。 - 特許庁
A state of an overvoltage of one power-source unit A1 is determined thus by observing a state that an output current Io2 of the power-source unit A2 drops lower than the average of output currents Io1, Io2 of all power-source units A1, A2 in a current circuit 31 of the unit. 他の電源ユニットA1の過電圧状態は、自機の電流分担回路31において全ての電源ユニットA1,A2の出力電流Io1,Io2の平均値に対し自機の電源ユニットA2の出力電流Io2が低くなることで判断できる。 - 特許庁
This source follower circuit comprises a MOS transistor M3 which is applied with the analog signal Vin at its gate and has its source connected to the bulk terminal B_1 of the MOS transistor M_1 and a current source 12 which supplied a bias current to the MOS transistor M3. このソースフォロワー回路は、ゲートにアナログ信号Vinが印加されると共に、ソースがMOSトランジスタM1のバルク端子B1に接続されたMOSトランジスタM3と、MOSトランジスタM3にバイアス電流を供給する電流源12とから構成される。 - 特許庁
Even after detecting the deteriorated exciting light source element 11a, using a drive current common target value calculation means 27, the target value of a driving current to be supplied to respective exciting light source elements 11a is set to the same value in respective exciting light source elements 11a. また、劣化した励起光源素子11aが検出された後も、駆動電流共通目標値算出手段27を用いて各励起光源素子11aへ供給する駆動電流の目標値を各励起光源素子11aで同一とする。 - 特許庁
To maintain constant an optical output from a laser light source by correcting a threshold current and an addition current of the laser light source in a short time by simple circuit configuration and control even when a differential efficiency of the laser light source changes due to surrounding environment and secular change. 周囲環境や経時変化によってレーザ光源の微分効率が変化した場合であっても、簡単な回路構成及び制御でもって、短時間でレーザ光源の閾値電流及び加算電流を補正して、レーザ光源からの光出力を一定に保つ。 - 特許庁
To provide a method for controlling a video display apparatus with a multiple signal source which changes over a current mode to a power-saving mode when a power-saving instruction is inputted from a computer and a signal source is selected by the computer, and which continues the current mode when a signal source is not selected by the computer but from another signal source. コンピューターから節電命令が入力される場合,信号源選択状態がコンピューターであると現在モードを節電モードに転換し,信号源選択状態がコンピューターではない他の信号源であると,現在モードを持続させる多重信号源を有する映像表示機器の制御方法を提供すること。 - 特許庁
An input voltage signal VIN input into a gate terminal of a PMOS transistor M1 is converted into a voltage value shifted by a voltage between a gate and a source of the PMOS transistor M1, in a source terminal, in response to a bias current I1 flowing via the source terminal of the PMOS transistor M1 by a constant current source IS. PMOSトランジスタM1のゲート端子に入力される入力電圧信号VINは、定電流源ISによりPMOSトランジスタM1のソース端子を介して流されるバイアス電流I1に応じて、ソース端子においてPMOSトランジスタM1のゲート・ソース間電圧でレベルシフトされた電圧値に変換される。 - 特許庁
Since, as the power supply voltage VDD of the constant current circuit, the addition voltage of one voltage between the drain and source and one voltage between the gate and source becomes necessary and no addition voltage of one voltage between the drain and source and two voltages between the gate and source becomes unnecessary, the minimum operation supply voltage of the constant current circuit becomes low. 定電流回路の電源電圧VDDとして、1つのドレイン・ソース間電圧と1つのゲート・ソース間電圧との加算電圧が必要になり、1つのドレイン・ソース間電圧と2つのゲート・ソース間電圧との加算電圧は必要ならないので、定電流回路の最低動作電源電圧が低くなる。 - 特許庁
The imaging apparatus further includes a constant current source 35 for forming a source follower circuit together with the amplification transistor AMP during the read operation of the amplification transistor AMP, and a current control part 36 for variably controlling the output current value of the constant current source 35 during the read operation of the amplification transistor AMP according to supplied control signals ϕA and ϕB. 撮像装置は、更に、増幅トランジスタAMPの読み出し動作時において増幅トランジスタAMPと共にソースフォロワ回路を形成する定電流源35と、増幅トランジスタAMPの読み出し動作時における定電流源35の出力電流値を、供給される制御信号φA,φBに応じて可変に制御する電流制御部36と、を更に備える。 - 特許庁
A conductive layer 120 is placed between the first source/drain regions of the respective MOSFET and they introduce current to the first source/drain regions 14 from one first source/drain regions 152. 導電層120は、各MOSFETの第1のソース/ドレイン領域の間に置かれて、1つの第1のソース/ドレイン領域152から他の第1のソース/ドレイン領域154に電流を導く。 - 特許庁
The backlight device 120 includes a power source line 200 of an anode side, a power source line 210 of a cathode side, and a plurality of current paths 220, 222, 224 connected in parallel between the power source lines. 本発明に係るバックライト装置120は、アノード側の電源ライン200と、カソード側の電源ライン210と、電源ライン間に並列に接続された複数の電流経路220、222、224とを含む。 - 特許庁
These power source drivers supply a current to correspondent sense power source lines SPL 0-SPLn+1 at the time of activation according to control voltage from active sense power source/control circuit 11a and 11b. これらの電源ドライバは、アクティブセンス電源/制御回路(11a,11b)からの制御電圧に従って活性化時対応のセンス電源線(SPL0−SPLn+1)へ電流を供給する。 - 特許庁
A feedback circuit reduces a channel current of an input MOS transistor and reduces a gate-source voltage of the input MOS transistor as a source voltage of the input MOS transistor of a source follower circuit increases. 本発明では、帰還回路は、ソースフォロワ回路の入力用MOSトランジスタのソース電圧が高いほど、入力用MOSトランジスタのチャネル電流を小さくし、そのゲート−ソース間電圧を小さくする。 - 特許庁
A first light source control part 51 supplies driving power to a first light source group 52 and adjusts its current value to control irradiation timing and illuminance of the first light source group 52. 第1光源制御部51は、第1光源群52に対して駆動電力を供給し、その電流値を調整することにより、第1光源群52の照射タイミングおよび照度を制御する。 - 特許庁
A second light source control part 53 supplies the driving power to a second light source group 54 and adjusts its current value to control irradiation timing and illuminance of the second light source group 54. 第2光源制御部53は、第2光源群54に対して駆動電力を供給し、その電流値を調整することにより、第2光源群54の照射タイミングおよび照度を制御する。 - 特許庁
When a power source section wherein the current value exceeds the limit value exists, an alarm signal is generated, and the power supply from a power source supply section 22 to the power source section wherein the abnormality occurs is stopped. 電流値がリミット値を超えている電源部が存在する場合には、アラーム信号を発生させ、電源供給部22この異常が発生した電源部への電源の供給を停止させる。 - 特許庁
To provide a vehicular light unit suppressing the breakage of a light source, in a structure driving the light source by a constant-current circuit and carrying out light control of the light source by PWM control. 定電流回路により光源が駆動されると共にPWM制御により光源の調光制御が行われる構成において、光源の破損を抑制できる車両用灯具を提供すること。 - 特許庁
Moreover, when a computer system 10 is driven while a commercial power source is being supplied, the system is driven using the power source split from the current-splitting circuit 7 in place of the power source from the battery. また、商用電源が供給されながらコンピュータシステム10を駆動する時には、バッテリからの電源供給ではなく、分流回路7より分流された電源を用いてシステム駆動する。 - 特許庁
The transistor 10 is configured to be a so-called source follower circuit wherein a constant current is supplied to the source of the transistor 10 and the same potential level is applied to the gate and the drain, and the transistor 10 outputs the source potential level as the output voltage. トランジスタ10は、ソースに定電流が供給され、ゲートとドレインに同電位が印加され、ソース電位を出力電圧として出力する、いわゆるソースフォロワ回路として構成されている。 - 特許庁
The adjusting circuit 52 is connected to a power source line 2 set to power source voltage VCC, and supplies a stable bias current IP to the bias section 12 even if temperature and power source voltage VCC are fluctuated. 調整回路52は、電源電圧V_CCに設定された電源線2に接続され、温度および電源電圧V_CCが変動しても安定したバイアス電流I_P をバイアス部12に供給する。 - 特許庁
To provide a liquid crystal module having a linear light source as a backlight light source, in which a leakage current due to a stray capacitance generated in the linear light source can be reduced at low cost. バックライト用光源として線状光源を備える液晶モジュールにおいて、線状光源において生じる浮遊容量に基づく漏れ電流を低コストで低減可能な液晶モジュールを提供する。 - 特許庁
As the result, the mechanical component 4 short-circuited with the GND, other output voltage or the like is intercepted from a direct current electric source part 2 for mechanical driving/controlling part (S7) and a direct current electric source part 1 is protected from an overcurrent state. そのため、GNDや他の出力電圧等と短絡しているメカ部品4がメカ駆動/制御部用直流電源部2と遮断(S7)され、直流電源部1が過電流状態から保護される。 - 特許庁
The drain of the PMOS 1 is connected to a first constant current source 1 through a third switching element SW 3 and also connected to a second constant current source 3 through a fourth switching element SW 4. PMOS1のドレインは、第3のスイッチング素子SW3を介して第1の定電流源1と接続されており、また、第4のスイッチング素子SW4を介して第2の定電流源3と接続されている。 - 特許庁
To achieve a circuit cooperation analysis in a low frequency area requiring no consideration of a displacement current, with respect to a circuit model where an arbitrary impedance and a current source or a voltage source are arranged between conductors. 変位電流を考慮する必要のない低周波の領域において、導体間に任意のインピーダンスや電流源もしくは電圧源を配置した回路モデルについての回路連携解析を行えるようにする。 - 特許庁
When the power source is connected to a power supply voltage terminal Tv1, a circuit starting part 1 supplies a current for starting a bias voltage generating part 2 and a constant current supply part 3 by fetching a voltage from the power source. 電源電圧端子Tv1に電源が接続されると、回路起動部1は、電源から電圧を取り込んでバイアス電圧生成部2と定電流供給部3を起動するための電流を供給する。 - 特許庁
In the discharge lamp lighting circuit 1, if a value of an input power source voltage decreases to less than 100V (for example, a 90V of an effective voltage), a current volume of a tube current decreases by the decreased value of the input power source voltage. 放電灯点灯回路1では、入力電源電圧の値が100V未満に(例えば実効電圧90Vに)低下した場合、入力電源電圧の値が低下した分、管電流の電流量が低下する。 - 特許庁