To provide a semiconductor memory device equipped with a transistor disposed as a current limiter to limit a current between a bit line precharge power source and a bit line, wherein a leaked current via a current limiter in the circuit of a defective column can be suppressed to a minimum. ビット線プリチャージ用電源とビット線との間に電流を制限するカレントリミッタとしてのトランジスタを備えた半導体記憶装置における不良カラムの回路中のカレントリミッタを介したリーク電流を最小限に抑制することが可能な半導体記憶装置を提供する。 - 特許庁
Consequently, the electric current flows from a direct current electric power source in a state where the cutting tip 112 and the standard member 92 make contact with each other through the electrically conductive film, and contact of the cutting tip 112 and the standard member 92 is detected as an electric current detector 100 detects the electric current. それにより、切削チップ112と標準部材92とが導電膜を介して互いに接触する状態で直流電源から電流が流れ、電流検出器100がその電流を検出することにより切削チップ112と標準部材92との接触が検出される。 - 特許庁
To obtain a power current of a proper waveform by suppressing increase of a harmonic current of a specific order by influence of a shunt current to a capacitor, in a configuration having the capacitor connected between a load device connected to a power source and a detector of a load current thereof. 電源に接続された負荷装置とこの負荷電流の検出器との間にコンデンサが接続された構成において、そのコンデンサへの分流電流の影響による特定次数の高調波電流の拡大を抑制することによって、適正波形の電源電流を得ること。 - 特許庁
To provide driving equipment, which makes current of each light emitting diode circuit containing the light emitting diode that is a light source for illumination so that it may be switching-controlled by a bipolar transistor, which is the transistor with small current capacity, utilizing a constant current circuit and a current mirror circuit effectively. 定電流回路及びカレントミラー回路を有効に活用して、照明用光源である発光ダイオードを含む各発光ダイオード回路の電流を、電流容量の小さなトランジスタであるバイポーラトランジスタでもって、スイッチング制御するようにした発光ダイオード用駆動装置を提供する。 - 特許庁
Mixing of the fundamental colors is performed by flowing a pulse current to a variable wavelength light emission diode 30 from a pulse power source 28, wherein the pulse current has a predetermined number of peak current values, and a cycle between pulse groups including the pulses of different peak current values is a predetermined pulse cycle or less. 基本色の混合は、波長可変発光ダイオード30にパルス電源28から所定の個数のピーク電流値を有するパルス電流であって、異なるピーク電流値のパルスを含むパルス群間の周期が所定のパルス周期以下であるパルス電流を流すことにより行なう。 - 特許庁
During charging before leakage current measurement of a capacitor 4, a charging voltage where an alternating voltage va is superimposed on a direct voltage Vp of a measuring direct current power source 1 is applied to converge a dielectric absorption current in a short time, so that a true leakage current is measured in a short time. コンデンサ4の漏れ電流測定前の充電期間中に測定用直流電源1の直流電圧Vpに交流電圧vaを重畳させた充電電圧を印加し、誘電吸収電流を短時間に収束させることにより、真の漏れ電流を短時間で測定する。 - 特許庁
Electric charges at the gate terminal are pulled out at a fixed current value by the current of the switchable current source 52, even when the gate voltage of the NMOS transistor 15 of the output buffer 8 varies within a range of variations of a threshold voltage Vth. 前記SW機能付電流源52の電流は、前記出力バッファ8のNMOSトランジスタ15のゲート電圧が閾値電圧Vthのばらつき範囲内でばらついても、一定の電流値でゲート端子の電荷を引き抜く。 - 特許庁
The drive circuit adjusts the white balance of the display panel, by changing the current value of constant current or the width of pulse current supplied to the light source which emits a light of a prescribed color, with a specified ratio with respect to the lighting time. 前記駆動回路は、所定の色の光を発光する光源に供給する定電流の電流値又はパルス電流の幅を、点灯時間に対し、一定の割合で変化させることにより表示パネルのホワイトバランスを調整する。 - 特許庁
In the same way, in a state with PC 11 connected, when the current consumption amount becomes a predetermined value or larger, a current detection means 10 notifies the power source control circuit 7 that the current consumption has reached a predetermined value or larger. 同様に、PC11が接続された状態において、電流の消費量が所定値以上になると、電流検出手段10は、電源制御回路7に消費電流が所定値以上に達したことを伝える。 - 特許庁
To provide a reference current source circuit that outputs a constant reference current, even if surrounding environments such as temperature and power supply voltage change, in a power supply circuit operated in a minute current region in an order of nanoamperes. ナノアンペアオーダーの微小電流領域で動作する電源回路において、温度や電源電圧などの周囲環境が変化しても一定の基準電流を出力することができる基準電流源回路を提供する。 - 特許庁
The air conditioner AC comprises a crank case heater 26 connected between the N phase and an L1 phase of the AC power source 1, a first current transformer 28 and a second current transformer 29 which detect an electric current flowing through the N phase and the L1 phase, and a controller 12. 交流電源のN相とL1相との間に接続されたクランクケースヒータ26と、N相及びL1相に流れる電流を検出する第1の変流器28及び第2の変流器29と、コントローラ12を備える。 - 特許庁
This DC current stabilization power source unit is provided with an automatic gain control circuit (AGC circuit) 5 for detecting an output current Io to reduce a gain in a drive circuit 4 when the output current Io is great. 直流安定化電源装置において、出力電流Ioを検出して出力電流Ioが大きければドライブ回路4のゲインを小さくするオートゲインコントロール回路(AGC回路)5をドライブ回路4内に設ける。 - 特許庁
A multistage circuit is provided with a diode-connected transistor 415 serially connected with a resistor 414, and the resistor 414 and transistor 415 are supplied with a current by a current source 413 to generate a direct-current voltage potential at an E-point. 多段回路に、抵抗器414と直列に接続されたダイオード接続トランジスタ415を設け、電流源413により抵抗器414及びトランジスタ415に電流を供給することで、E点に直流電位を生成する。 - 特許庁
In a test mode, the current supply from a power supply voltage Vcc to the power source nodes 43a and 43b is stopped by current switches 102a and 102b and an externally adjustable test current is supplied. テストモード時には、電源ノード43a,43bに対しては、電流スイッチ102a,102bによって電源電圧Vccからの電流供給が停止される一方で、外部から調整可能なテスト電流Itが供給される。 - 特許庁
The first current source generates first current, and voltage derived from the first current at least partially comprises a cell position dependent temperature coefficient varying with the position of a memory cell in the string of bit cells connected with each other. 第1電流源は第1電流を生成し、第1電流から導出される電圧は、相互接続されたビット・セルのストリングにおけるメモリ・セルの位置と共に変化するセル位置依存温度係数を少なくとも部分的に含む。 - 特許庁
The detector has a return current zeroized node, electrically combined with the output and the reference of the AC voltage source, a ground node separately coupled electrically with the ground, a positive ion current sensor, and a negative ion current sensor. 検出回路は、AC電圧源の出力と基準とに電気的に結合されている戻り電流ゼロ化ノードと、別個に接地に電気的に結合されている接地ノードと、正イオン電流センサと、負イオン電流センサとを含む。 - 特許庁
This trouble detection method for the current detecting circuit detects a trouble in the current detecting circuit 1 connected to an electric power source 2 with positive and negative poles, and for outputting a voltage corresponding to a detecting current to an output terminal 3. 電流検出回路の故障検出方法は、プラスマイナスの電源2に接続されて、検出する電流に対応する電圧を出力端子3に出力する電流検出回路1の故障を検出する方法である。 - 特許庁
A part of the current from the constant-current sources IX1-IXn is prevented from flowing into the supply source VM of the reverse bias voltage via the parasitic capacity of the EL element of a non-scanning state due to the existence of the constant-current circuit IYO. 定電流回路IY0の存在により、非走査状態のEL素子の寄生容量を介し、定電流源IX1〜IXnからの電流の一部が逆バイアス電圧の供給源VM に流入するのが阻止される。 - 特許庁
The switching element 12 on synchronization side breaks the lower limit of the ripple current changing with the passage of time, and it is the current value at the time t12 when the switching element 11 on power source side is switched, and it is in the vicinity of the current value becoming zero. 時間経過とともに変化するリップル電流の下限は、同期側スイッチング素子12が遮断して、電源側スイッチング素子11が導通する時刻t12での電流値であり、電流値がゼロとなる付近である。 - 特許庁
A differential circuit 5a comprises a different pair of transistors N1 and N2, and a tail current source 68 that supplies a tail current switchable so that the amount of current flowing through the different pair of transistors N1 and N2 is switched in at least two levels. 差動回路5aは、差動対トランジスタN1,N2と、差動対トランジスタN1,N2に流れる電流量が少なくとも2つのレベルで切替わるように、切替可能なテール電流を供給するテール電流源68とを備える。 - 特許庁
An AC power supply unit 1 is connected to a first LED light source unit 3 via a constant-current power supply circuit 2, and a current-limiting resistor 5a and an electricity storage unit 4 via the constant-current power supply circuit 2 and a lighting control unit 7. 交流電源部1は、定電流電源回路2を介して第1LED光源部3と、定電流電源回路2から点灯制御部7を介して電流制限抵抗5aから蓄電部4に接続されている。 - 特許庁
A current flowing primary windings 2-a1 and 20a2 of a pulse transformer 20a is controlled constant by a constant current source 20d and the controlled current is negatively fed back to a switching part 20c via a negative feedback resistance Rf and a negative feedback capacitor Cf to constitute a linear amplifier. パルストランス20aの一次巻線20a1、20a2に流れる電流を定電流源20dで一定に制御し、負帰還抵抗Rfと負帰還コンデンサCfを介して前記制御された電流をスイッチング部20cに負帰還してリニアアンプを構成する。 - 特許庁
Voltage is applied to an attracting roll 25 from an attracting roll power source 30, and a current is made to flow to a metallic roll 26 via paper and a paper carrying belt 3, and further a current is made to flow to the ground via a current detection circuit 27. 吸着ロール電源30から吸着ロール25に対して電圧を印加し、用紙及び用紙搬送ベルト3を介して金属ロール26に電流を流し、更に電流検出回路27を通して接地に電流を流す。 - 特許庁
In an apparatus main body 3, a monitor current for calculating the resistance value at a room temperature of the heat generation elements 21 (21a-21c) is controlled by a monitor current control circuit 101 and outputted from a monitor constant current power source 102. 装置本体3において、発熱素子21(21a〜21c)の室温時の抵抗値を算出するためのモニタ電流は、モニタ電流制御回路101によって制御され、モニタ定電流電源102から出力される。 - 特許庁
In a normal read operation, read voltage is applied to the control gate of the main body cell MC and the control gates of the reference cells RC03, RC13, RC23 of the reference current source circuit 32, reference current values for read-out Iread01, Iread12, Iread23 are compared with a cell current. 通常の読み出し動作では、本体セルMCの制御ゲートと、基準電流源回路32の参照セルRC03,RC13,RC23の制御ゲートに読み出し電圧を印加し、読み出し用基準電流値Iread01,Iread12,Iread23とセル電流を比較する。 - 特許庁
First coils 1, 2 wound in a substantially 8-shape, to which alternating current or pulse current is applied from an alternating current source (not shown) through a transformer, connecting wires 1a, 2a, and the like, are located on the side of a human body (not shown). 第1のコイル1,2は、ほぼ8の字状に巻き回され、図示されない交流電源から変圧器および接続線1a,2aを介して交流電流またはパルス電流が通電され、図示されない人体側に配置される。 - 特許庁
The current source executes the current supply operation to the first transistor during a starting state of the voltage-controlled oscillator and stops the current supply operation to the first transistor during a normal state of the voltage-controlled oscillator. 電流源は、電圧制御発振器の起動状態時に第1トランジスタに対する電流供給動作を実施し、電圧制御発振器の定常状態時に第1トランジスタに対する電流供給動作を停止する。 - 特許庁
In a transistor Q12, a current compensating circuit 11, and a signal-current source 13, an electric signal Vin of a digital signal to be transmitted is inputted thereto to generate a signal current Io caused by compensating the frequency band of the electric signal Vin. トランジスタQ12、電流補償回路11および信号電流源13において、伝送すべきディジタル信号の電気信号Vinを入力し、電気信号Vinを帯域補償させた信号電流I0 を生成する。 - 特許庁
A current detection part has negative input offset voltage characteristics, detects a first sense current when being connected to a power source and the sense MOS, and detects a second sense current when being connected to the sense MOS and the load MOS. 電流検出部は、負の入力オフセット電圧特性を有し、電源とセンスMOSに接続されたときの第1のセンス電流を検出し、センスMOSと負荷MOSに接続されたときの第2のセンス電流を検出する。 - 特許庁
The operational amplifier is provided with an idling current control section 4 that controls an idling current Id of the output transistor by controlling a collector current of the source side output transistor T1 based on the base potential of the sink side output transistor T2. シンク側出力トランジスタT2のベース電位に基づいて、ソース側出力トランジスタT1のコレクタ電流を制御することにより、出力トランジスタのアイドリング電流Idを制御するアイドリング電流制御部4が備えられる。 - 特許庁
According to a panel current which is the total current to be supplied to each pixel, the image data are corrected so that a correction error can be reduced considering a voltage drop due to flowing of the panel current to the resistance component on the power source line. また、各画素へ供給される電流の合計であるパネル電流に応じ、電源ラインにおける抵抗成分にパネル電流が流れることによる電圧降下を考慮し、補正誤差が低減するように画像データを補正する。 - 特許庁
A constant current is made to flow from a constant current source 12 to an (N+M)-diode series-connection circuit and then a constant current is made to flow to an N-diode series-connection circuit, so that voltages VT1 and VT2 are developed at respective terminals. N+M個のダイオード直列接続回路に定電流源よりI1の一定電流を流し、N個のダイオード直列接続回路にI2の一定電流を流すと、各端子に電圧VT1と電圧VT2が現れる。 - 特許庁
When the motor current Im further increases, a power generation voltage Vf decreases so as to increase a power generation current If, while the first source current Ibse is maintained at the upper limit value, and therefore a fuse 25 is prevented from being melted. モータ電流Imがさらに増加した場合には、発電電流Ifが増加するように発電電圧Vfが減少するが、第1ソース電流Ibseは上限値に保持されるので、ヒューズ25の溶断が防止される。 - 特許庁
A second current source 114 outputs a second current based on the input voltage to a second input terminal b, and is set to be capable of controlling change in variation of the second current to the input voltage. 第2の電流源114は、第2の入力端子bへの入力電圧に応じて第2の電流を出力すると共に、入力電圧に対する第2の電流の変化量の変更制御が可能に設定される。 - 特許庁
The CMOS constant current circuit is constituted so that a MOS transistor MP10 in which an interval between a gate and a source is short-ciruited is connected to an output edge of the CMOS constant current circuit and it is stably operated using leak current generated in the MOS transistor at high temperature. CMOS定電流回路の出力端に、ゲート・ソース間を短絡したMOSトランジスタMP10を接続し、高温時にMOSトランジスタに発生したリーク電流を利用して安定動作させる構成とした。 - 特許庁
Thus the output current range of the current source for outputting small amounts of currents as a single body is made narrower so that the decrease of voltage in a resistance can be made larger, and current precision in outputting a small amount of currents can be improved. この工夫により、少電流出力用の電流源では、単体での出力電流範囲が狭まるために、抵抗での電圧降下を大きく出来、少電流出力時の電流精度を改善することが可能である。 - 特許庁
Then, the values voltage to be supplied from a variable power source to the above two pixel parts are corrected so that the measured drive current becomes a reference value by measuring drive current in the pixel part for measuring the drive current of the OLED. OLEDの駆動電流を測定するための画素部において駆動電流を測定し、測定した駆動電流が基準の値になるように、可変電源から上記2つの画素部に供給される電圧の値を補正する。 - 特許庁
A MOS transistor(TR), M101 and a MOS TR M102 configure a current mirror circuit and the drain-source resistance of the MOS TR M102 is changed so that the current i101 is equal to the current i102. MOS型トランジスタM101およびMOS型トランジスタM102はカレントミラー回路を構成しており、電流i101と電流i102が等しくなるようにMOS型トランジスタM102のドレイン−ソース抵抗が変化する。 - 特許庁
Because information about a requested voltage value and current value is included in the request information transmitted from the source device 110 to the sink device 120, the source device 110 receives the power of the required voltage value and current value from the sink device 120. ソース機器110からシンク機器120に送信する要求情報に、要求する電圧値、電流値の情報を含めることで、ソース機器110は、シンク機器120から、必要とする電圧値、電流値の電源の供給を受ける。 - 特許庁
In a standby state, a photo diode circuit 110 and a current amplifier 112 in the first stage are supplied with a power source voltage to operate, and current amplifiers 114 and 116 in the second stage or later are not supplied with a power source voltage and prevented from operating. スタンバイ状態の際には、フォトダイオード回路110と初段の電流アンプ112に電源電圧を供給して動作させるが、2段目以降の電流アンプ114及び116に電源電圧を供給せずに動作させない。 - 特許庁
Respective values of resistance R_DS between a drain and the source of the second and third MOS transistors Q2 and Q3 are changed by changing a supply current from a current source I1 to the first MOS transistor Q1 in order to perform a control gain. 電流源I1による第1のMOSトランジスタQ1への供給電流を変化させることにより、第2および第3のMOSトランジスタQ2,Q3それぞれのドレイン−ソース間抵抗R_DSの値を変化させ、利得制御を行う。 - 特許庁
The injection hole plate 40 of Ni-Co alloy is formed on the bottom part outer wall 15 of the valve body 12 by electrocasting by connecting an anode of a direct current electric power source 90 to a Ni electrode 92 and connecting a cathode of the direct current electric power source 90 to the valve body 12. 直流電源90の陽極をNi電極92と接続し、直流電源90の陰極を弁ボディ12と接続すると、弁ボディ12の底部外壁15にNi−Co合金の噴孔プレート40が電鋳により形成される。 - 特許庁
A first reference voltage ACLVref is outputted from an intermediate point between the first resistor R3 and the first constant current source 12, and a second reference voltage ABLVref is outputted from an intermediate point between the second resistor R4 and the second constant current source 14. 第1抵抗R3と第1定電流源12の中間点から第1基準電圧ACLVrefを出力し、第2抵抗R4と第2定電流源14の中間点から第2基準電圧ABLVrefを出力する。 - 特許庁
A substrate 1 on which a wiring 3 is formed, is electrically connected to the cathode of a direct current source and an electrode electrically connected to the substrate 1 and the anode of the direct current source is dipped in a resist tank filled with colloid electrodeposition resist liquid. 配線3の形成された基板1を直流電源の陰極と電気的に接続し、基板1およびその直流電源の陽極と電気的に接続した電極をコロイド状の電着レジスト液で満たされたレジスト槽に浸す。 - 特許庁
The threshold voltage source 22 includes a reference transistor M2 of the same type as the switching transistor M1 and having a first terminal to which a fixed voltage GND is applied, and a constant current source 26 for supplying a predetermined constant current Ic1 to the reference transistor M2. しきい値電圧源22は、スイッチングトランジスタM1と同型であって、第1端子に固定電圧GNDが印加される基準トランジスタM2と、基準トランジスタM2に所定の定電流Ic1を供給する定電流源26と、を含む。 - 特許庁
To write information into one of the memory cells MC1-MC3, the 1st terminal A1 of the 1st conductor line LB1 is connected with a current source Q1, and the 2nd terminal A2 of the 2nd conductor line LB2 is connected with another current source Q2. 情報をメモリセルMC1〜MC3の1つへ書き込むため、第1の導体路LB1の第1の端子A1は電流源Q1と接続されており、第2の導体路LB2の第2の端子A2は別の電流源Q2と接続されている。 - 特許庁
A current source 102 is provided as a common power source for the semiconductor light sources 101-1 to 101-K to supply the driving currents of the semiconductor light sources 101-1 to 101-K according to the result of addition of the current command values N_1 to N_K. 電流源102は、半導体光源101−1〜101−Kの共通電源として設けられ、半導体光源101−1〜101−Kの駆動電流を、電流指令値N_1〜N_Kの加算の結果に応じて供給する。 - 特許庁
The cylindrical electrode 13 is connected to direct-current electrolyte power source 10 through a lead wire 14, and the carbon matter material 15 is hung from a support rod 16 through a clamp 17, and further, connected to the direct- current electrolyte power source 10 through the lead wire. 円筒電極13はリード線14を介して直流電解電源10に接続され、炭素物質材料15はクランプ17を介して支持棒16に吊り下げられ、更にリード線を介して直流電解電源10に結線される。 - 特許庁
A transistor Q2 has a base current flow to form an ON state if the output voltage of the power source device 1 is a rated voltage, and has no base current flow to form an OFF state if the output voltage of the power source device 1 is a standby voltage. トランジスタQ2は、電源装置1の出力電圧が定格電圧である場合には、ベース電流が流れてON状態になり、電源装置1の出力電圧が待機電圧である場合には、ベース電流が流れずOFF状態になる。 - 特許庁
A control part 13 causes a current having a first value larger than 0 and a current having a second value larger than the first value to flow to a light source 11 in accordance with data accepted by an acceptance part 12, and data are transmitted by visible light emitted from the light source 11. 、制御部13は、受付部12が受け付けたデータに応じて、0より大きい第一の値の電流と、第一の値より大きい第二の値の電流とを、光源11に流して、光源11が発光する可視光でデータを送信する。 - 特許庁