「input- current」を含む例文一覧(4743)

<前へ 1 2 .... 61 62 63 64 65 66 67 68 69 .... 94 95 次へ>
  • The current detection circuit 6 is configured to input a voltage Vs corresponding to the value of supply currents I from a high order side system 200, and to obtain an output voltage Vc by performing the inversion amplification of the voltage Vs.
    電流検出回路6は、上位側システム200からの供給電流Iの値に応じた電圧Vsを入力とし、この電圧Vsを反転増幅して出力電圧Vcとする。 - 特許庁
  • As an image signal input to a pixel from a source signal line, a desired potential is applied to a gate of a diode-connected transistor for supplying the electric current to the display device.
    ソース信号線より画素に入力される映像信号は、表示素子に電流を供給するためのトランジスタをダイオード接続とし、当該ダイオード接続されたトランジスタのゲートに所望の電位が印加される。 - 特許庁
  • To provide a current output digital/analog converter that suppresses variations in output impedance by a digital input code, has a small amount of error in analog output and linearity, and can be operated at a high speed.
    ディジタル入力コードによる出力インピーダンスの変動を抑え、アナログ出力の誤差が少なく、直線性を有する高速動作可能な電流出力型ディジタル・アナログコンバータを提供する。 - 特許庁
  • The optical receiver 26 further comprises a DC power supply 38 for operating the optoelectronic converter 34, based on a DC current transmitted from the input side of the amplifier 2 through the coaxial cable 24.
    同軸ケーブル24を介して増幅器2の入力側から伝送された直流電流に基づいて光−電気変換器34を作動させる直流電源38も、光受信機26は有している。 - 特許庁
  • Then a resistor 6 for buffering is interposed between P type transistors M201, M211, M221, and M231 included in the reference current circuit 2, input circuit 3, and output circuit 4, and a next-stage circuit.
    そして、基準電流回路2、入力回路3、出力回路4に含まれるP型トランジスタM201、M211、M221、M231とその次段の回路との間に緩衝用の抵抗6が挿入される。 - 特許庁
  • The tuning amplifier circuit has a first input transistor subjected to cascade connection, a first cascode transistor and a first transistor for bias current control, and a serially connected tuning element.
    同調増幅回路は、従属接続される第1の入力トランジスタ、第1のカスコードトランジスタおよび第1のバイアス電流制御用トランジスタと、直列に接続される同調素子とを有する。 - 特許庁
  • Moreover, a reversed connection protecting means 5 is set for preventing an input current from being fed to a load, when the DC power source is detected by the polarity- determining means 3 to be inputted with a reversed polarity.
    また、極性判別手段3によりDC電源が逆極性入力されていることを検知したときに、入力電流の負荷側への供給を阻止する逆接続保護手段5を有する。 - 特許庁
  • When the input voltage is low or the output load current is small, the voltage induced in the bias windings and the switch circuit 46 is therefore turned on to increase the supplied bias voltage.
    また、入力電圧が低いか、出力負荷電流が少ない状態では、バイアス巻線に誘起される電圧が低くなるため、スイッチ回路46をオンして供給されるバイアス電圧を上げる。 - 特許庁
  • The constant-current generating circuit 11 has a resistance having large temperature dependence therein, and generates a bias voltage BIASN changed by the ambient temperature to input it to the bias voltage adjusting circuit 12.
    定電流発生回路11は、温度依存性の大きい抵抗を内部に有し、周囲の温度によって変化するバイアス電圧BIASNを発生させてバイアス電圧調整回路12へ入力させる。 - 特許庁
  • A DC/DC conversion circuit 1 which boosts and outputs an input direct current voltage comprises a plurality of capacitors C1-C4 and a connection device 10 which connects these in parallel or in series.
    入力された直流電圧を昇圧して出力するDC/DC変換回路1であって、複数のキャパシタC1〜C4と、これらを並列又は直列に接続する接続装置10とを備える。 - 特許庁
  • To increase an output displacement for input current and improve linearity in an actuator device, in which an ultra magnetorestrictive element and a motor are combined, to realize fine operation having multiple degrees of freedom.
    多自由度の精密動作を実現するために、超磁歪素子とモータを組み合わせたアクチュエータ装置において、入力電流に対する出力変位の増大と線形性の向上を図る。 - 特許庁
  • Consequently, a voltage of 5 V is applied from a voltage setting circuit 3 to the input terminal Ref of a driver IC 4 which thereby supplies a current of 1.5 A to the stepping motor M1.
    これによって、ドライバIC4の入力端子Refには電圧設定回路3から5Vの電圧が印加され、ドライバIC4からステッピングモータM1に供給される電流値は1.5Aとなる。 - 特許庁
  • Specifically, when an input voltage is high or an output load current is large, the voltage induced in the bias windings is increased and the switch circuit 46 is therefore turned off to reduce the bias voltage.
    すなわち、入力電圧が高いか、出力負荷電流が大きい状態では、バイアス巻線に誘起される電圧が高くなるため、スイッチ回路46をオフして供給されるバイアス電圧を下げる。 - 特許庁
  • To provide a discharge lamp lighting device which reduces distortion of an alternating input current, and moreover can prevent fading out of a discharge lamp upon deep light dimmer, a luminaire and a light dimmer illumination system.
    交流入力電流を低歪化させるとともに、放電ランプの深調光時の立消えを防止できる放電ランプ点灯装置、照明器具および調光照明システムを提供する。 - 特許庁
  • An input current resistance for driving mainly a DC motor is measured and the output characteristics of the DC motor are decided to adjust and control the output of the DC motor based on the output characteristics.
    主に直流モーターを駆動する入力電気抵抗を測定し、該直流モーターの出力特徴を決定し、こうして該出力特徴に基づき該直流モーターの出力を調整、制御する。 - 特許庁
  • A gain of an amplifier-cum-amplification extraction device 17 can be reduced by the amplification of the optical signal received by the photodiode 101 in the current amplification circuit 102 to reduce effects of input noise.
    また、電流増幅回路102でフォトダイオード101の受光信号を増幅する分だけ、アンプ兼増幅抽出デバイス17のゲインを抑制でき、入力ノイズの影響を低減できる。 - 特許庁
  • When a cursor signal transmitted from a remote controller is input, the focus is transited along the transition path of the focus based on focus position information representing the current position of the focus and the remote control command set.
    リモコンから送出されたカーソル信号が入力した際、フォーカスの現在位置を表すフォーカス位置情報と前記リモコンコマンドセットとに基づき、前記フォーカスの遷移経路に沿ってフォーカスを遷移させる。 - 特許庁
  • The voltage of an adding transformer is added to the direct- current voltage of a converter through a diode stack according to fluctuation in supply voltage to stabilize the input voltage of an inverter and motor torque reduction is thereby prevented.
    コンバータ部の直流電圧に加算トランスの電圧を電源電圧の変動に対応してダイオードスタックを通じて加算し、インバータ部の入力電圧を安定化してモータの回転力低下を防止する。 - 特許庁
  • When the engagement is disengaged, since connection failures occur in the terminals 3a, 4a, etc., the current is not made to flow to the light-emitting diode D1, and the voltage in the input port IP5c becomes low level.
    嵌合が外れている場合は、端部の端子3a、4a等が接続不良となるため、発行ダイオードD1に電流が流れず、入力ポートIP5cにおける電圧はローレベルになる。 - 特許庁
  • A current i and an output (respectively input) voltage V of the amplifier and their phase shift are measured, and a complex impedance defined by V/i is deduced from the measured values.
    増幅器の電流iおよび出力(それぞれ入力)電圧Vならびにそれらの位相変移が測定され、V/iによって定義される複素インピーダンスがこれらの測定値から推定される。 - 特許庁
  • Consequently, even when the disturbance wave is input, no diode passing current is generated, so harmonics and higher distortion generated by applying a voltage between terminals of the diode can be prevented from being generated.
    これによって、妨害波が入力してもダイオード通過電流が発生しないので、ダイオードの端子間に電圧が加わることによって生じる高調波や高次歪の発生を防止することができる。 - 特許庁
  • The output side transistors Qo1 to Qo4 are PNP type bipolar transistors, and a base and an emitter are each commonly connected to those of the input side transistor Qi to form a current mirror circuit.
    出力側トランジスタQo1〜Qo4は、PNP型バイポーラトランジスタであって、ベース、エミッタがそれぞれ、入力側トランジスタQiのそれらと共通に接続されてカレントミラー回路を形成する。 - 特許庁
  • This program timer unit is provided with a synchronizing signal input unit which inputs a synchronizing signal to make the current time coincide with the external time, and a synchronizing signal output unit which outputs the synchronizing signals to the outside.
    プログラムタイマユニットは、現在時刻を外部の時刻と一致させる同期信号が入力される同期信号入力部と、前記同期信号を外部に出力する同期信号出力部と、を備える。 - 特許庁
  • It also include to estimate an input current command value, to estimate a power conversion efficiency, and the like, and to take account of the inductance of the AC power supply in the filter constant.
    出力電圧指令値から入力電流指令値を推定すること、電力変換効率等を含めて推定すること、フィルタ定数に交流電源のインダクタンス成分も考慮することなども含む。 - 特許庁
  • Consequently, without giving the danger of exceeding the maximum input dose rate, the whole of the length can be used by adjusting a required tube parameter (tube voltage, tube current, or a load).
    その結果、最大の入力線量率を超過する危険性を与えることなしに、その長さ全体が所望の管パラメータ(管電圧、管電流、又は負荷)を調整することによって使用されうる。 - 特許庁
  • In addition, the driving section 15 supplies a driving current in such a range that the maximum output light level of the semiconductor optical amplifier 13 does not exceed the maximum input light level of the light receiving element 12.
    また、駆動部15は、半導体光増幅器13の最大出力光レベルが、受光素子12の最大入力光レベルを超えない範囲で駆動させるに相当な駆動電流量を供給する。 - 特許庁
  • To provide a power converter capable of avoiding giving any interference to a load such as a power system or a motor by obtaining sinewaves without any distortion in an input current waveform and an output voltage waveform.
    入力電流波形及び出力電圧波形に歪みのない正弦波を得ることにより、電源系統や電動機等の負荷に障害を与えない電力変換装置を提供する。 - 特許庁
  • When it is used, the diode 430 lowers a gate voltage output from the gate drive chip applied to the gate input of the wide bandgap semiconductor junction gate transistor via the gate current limit resistor 445.
    使用時に、ダイオード430は、ゲート電流制限抵抗器445を介してワイドバンドギャップ半導体接合ゲートトランジスタのゲート入力に印加され、ゲート駆動チップからのゲート電圧出力を低下させる。 - 特許庁
  • To provide a high frequency heating device restraining overshoot of an input current in an instant of switching from starting to normal state, thereby preventing an IGBT and a magnetron from damage.
    起動から定常に切り替わった瞬間に入力電流のオーバーシュートを抑えることができ、したがって、IGBTおよびマグネトロンの損傷を防止できる高周波加熱装置を提供する。 - 特許庁
  • A current Id flowing in the component of a basic capacity value Cd out of the capacity sensor 8 with the input of AC voltage Vin is supplied from the second AC voltage generator 15 via the second capacitor 12.
    交流電圧Vinを入力し、容量センサのうち基礎容量値Cd分に流れる電流Idを、第2コンデンサ12を介して第2交流電圧発生器15から供給する。 - 特許庁
  • Thus, even if the value of the output signal voltage V_out is increased correspondingly to increase in a value of the input signal current I_in, without waveform distortion or speed deceleration, signal equivalent processing can be performed.
    これにより、入力信号電流I_inの値の増加に対応して出力信号電圧V_outの値が増加したときであっても、波形歪みや速度低下なく、信号等価処理をすることができる。 - 特許庁
  • The controlled voltage circuit 5 includes a plurality of MOSFET transistors 60 connected in series, a unity gain operational amplifier 30, and a constant current source 20 provided with an input terminal and an output terminal.
    被制御電圧回路5は、直列接続された複数のMOSFETトランジスタ60と、ユニティゲイン演算増幅器30と、入力端子と出力端子を備える定電流源20とを含む。 - 特許庁
  • The solenoid part 42 increases the set intake pressure as the input current value to the coil 51 becomes smaller, and sets the set intake pressure at a maximum value when the coil 51 is not energized.
    ソレノイド部42は、コイル51への入力電流値が小さくなるに連れて設定吸入圧力を高くし、コイル51の無通電時には設定吸入圧力を最高値とする構成である。 - 特許庁
  • An external characteristic function circuit ERF, containing a plurality of the external characteristics, takes a welding current detection signal id as an input and outputs an output voltage setting signal Er of welding power source.
    外部特性関数回路ERFは、複数子の外部特性を内蔵しており、溶接電流検出信号idを入力として溶接電源の出力電圧設定信号Erを出力する。 - 特許庁
  • The ground voltage is applied to the test terminal 10, and the current application voltage measurement is performed to the signal wiring 23, to thereby also detect the mounting defect of the input/output terminal 6.
    また、テスト端子10にグランド電圧を与えるとともに、信号配線23に対して電流印加電圧測定を行うことにより、入出力端子6の実装不良を検出することも可能である。 - 特許庁
  • The project manager calculates a risk value based on the current risk evaluation and outputs a graph, and the input of the risk evaluation after the measures for the studying items with the high risk values is accepted from the project manager.
    そして、現在のリスク評価にもとづくリスク値を算出してグラフを出力し、そのリスク値が高い検討項目についての対策後のリスク評価の入力をプロジェクト管理者から受け付ける。 - 特許庁
  • To provide an overcurrent alarm device which is reduced in the size of its case and arranged at the arbitrary position of a branch circuit using a small space, and in which an input line of a current transformer can be shortened.
    ケースを小型化することができ、分岐回路の任意の位置に少ないスペースで配設することができ、変流器の入力線を短くすることができる過電流警報装置を提供する。 - 特許庁
  • Since an NMOS transistor 14 is in interrupted state, when the input signal transits from the power supply voltage level to the reference voltage level, a through- current will not flow through an NMOS transistor 12.
    また、入力信号が電源電圧レベルから基準電圧レベルへと遷移するとき、NMOSトランジスタ14は遮断状態であるので、NMOSトランジスタ12には貫通電流は流れない。 - 特許庁
  • A DC offset elimination circuit 105 extracts a DC offset voltage with a differential output of the VGA 104 as an input and outputs a differential current proportional to the DC offset voltage.
    直流オフセット除去回路105は、VGA104の差動出力を入力として直流オフセット電圧を抽出するとともに、直流オフセット電圧に比例した差動電流を出力する。 - 特許庁
  • To provide an input circuit and a semiconductor memory device suitable for reducing deterioration of a signal level due to the signal interference in which a signal level in the past interferes with a current signal level.
    過去の信号レベルが現在の信号レベルと干渉する信号間干渉による信号レベルの劣化を低減することに適した入力回路及び半導体記憶装置を提供する。 - 特許庁
  • A power switching device Q1 responds to a switching signal to control an output of an input DC power supply, and an inrush current rushing into the switching device Q1 is interrupted by a diode D1.
    パワースイッチング素子Q1はスイッチング信号に応答して、入力される直流電源の出力を制御し、ダイオードD1により、パワースイッチング素子に突入される突入電流を遮断する。 - 特許庁
  • Source electrodes of differentially connected NMOSs 13 and 14 with small amplitude data inputted from an external part are connected to input terminals 1 and 2 in common and grounded through an NMOS 11 for current supply.
    入力端子1,2に外部からの小振幅データが入力される差動接続されたNMOS13,14のソース電極を共通接続し、電流供給用NMOS11を介して接地する。 - 特許庁
  • All circuit elements existing in current routes supplying an analog voltage from an analog voltage input part to a drain line DL in a drain driver 3 are constituted of analog switches containing analog multiplexers.
    本発明では、ドレインドライバ内でアナログ電圧入力部からドレイン線にアナログ電圧を供給する電流経路にある回路素子が、全てアナログマルチプレクサを含むアナログスイッチによって構成されている。 - 特許庁
  • To propose a PFC power conversion controller capable of providing a constant average output current, a constant average output voltage, and a constant power factor regardless of the amplitude of a full-wave rectification input voltage.
    全波整流入力電圧の振幅に関係無く、一定の平均出力電流、一定の平均出力電圧、一定の力率を提供可能なPFC電力変換制御装置を提案する。 - 特許庁
  • This current detection circuit 20 is provided with a variable gain amplifying circuit 22 capable of changing gain, and its output signal is inputted into an A/D conversion input port 11 of a microcomputer 10.
    この電流検出回路20は、ゲインの変更が可能な可変ゲイン増幅回路22を備えており、その出力信号は、マイクロコンピュータ10のA/D変換入力ポート11に入力される。 - 特許庁
  • A circuit comprises N type transistors Q1 and Q2 as input means, P type transistors Q3 and Q4 constituting an active load, a constant-current source IO, and a voltage difference detecting means DA.
    入力手段となるN型トランジスタQ1およびQ2、能動負荷を構成するP型トランジスタQ3およびQ4、定電流源I0、電圧差検出手段DAから構成されている。 - 特許庁
  • To make input of drop-off station simple when retrieving transfer information in a transfer guidance providing system and provide the transfer information corresponding to a user's current position.
    乗換案内提供システムにおいて、乗換情報を検索する際に降車駅等の入力を簡便なものにし、また、ユーザの現在位置に対応した乗換情報を提供できるようにする。 - 特許庁
  • To lessen the number of input terminals of a detection processor for detecting the values of currents flowing to a plurality of inductive loads in a current detector for controlling the currents of the inductive loads.
    複数の誘導性負荷の電流制御に用いられる電流検出装置において、各誘導性負荷に流れる電流値を検出する検出処理部の入力端子数を少なくする。 - 特許庁
  • When an input signal Sin changes from a high level to a low level, the impedance of an n-type MOS transistor MN11 is decreased attended with increase in a current I3, and a voltage at an output node Nout is decreased.
    入力信号Sinがハイレベルからローレベルへ変化する場合、電流I3の増加に伴ってn型MOSトランジスタMN11のインピーダンスが減少し、出力ノードNoutの電圧は低下する。 - 特許庁
  • The control circuit part 104 calculates a voltage value and a current value of both ends of the heater resistance through AD conversion input terminals AD1 and AD2, and calculates heater electric power as the product of these values.
    制御回路部104は、AD変換入力端子AD1とAD2を介して、ヒータ抵抗両端の電圧値と電流値を算出し、それらの積としてヒータ電力を算出する。 - 特許庁
<前へ 1 2 .... 61 62 63 64 65 66 67 68 69 .... 94 95 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.