A second timer circuit 25 establishes a threshold of a lamp voltage detecting means 24 to be less than the voltage of direct current input 1 during a second predetermined period shorter than the first predetermined period from power supply turning on and establishes the threshold to be more than the voltage value of a direct current input voltage 1 after the passage of the second predetermined period. 第2のタイマー回路25は、電源オン時から第1の所定時間より短い第2の所定時間の間、ランプ電圧検出手段24のしきい値を直流入力電圧1の電圧値未満に設定し、第2の所定時間経過後は前記しきい値を直流入力電圧1の電圧値以上に設定する。 - 特許庁
At transfer, a change-over circuit 12 is controlled to drive one of a transfer voltage control unit 14 and a transfer current control unit 16 and one of the primary input voltage, and the primary input current of a transformer 50 is controlled to be constant to obtain a prescribed value of the output of a half-wave rectifying circuit 51. 転写時には、切り替え回路12を制御して、転写電圧制御部14及び転写電流制御部16の何れかを駆動させて、トランス50の一次側入力を定電圧又は定電流制御して、トランス50の2次側の半波整流回路51の−出力を所定の大きさになるようにする。 - 特許庁
Decision is made whether the digital converter is in a continuous mode where the input current to the coil breaks off during control cycle or in discontinuous mode where the input current to the coil ceases in the way of a control cycle based on measurement in one measurement cycle for a plurality of control cycles, and the PWM control is performed according to different algorithm based on the decision result. コイルへの入力電流が制御サイクル中に途切れない連続モードか、制御サイクルの途中で途絶える不連続モードかを、複数の制御サイクルに一回の計測サイクルでの計測値に基づいて判定し、その判定結果に基づく異なるアルゴリズムで更新されたPWM制御を行う。 - 特許庁
A resistor is arranged in a path of current caused to flow to a differential input part of a differential output buffer, the value of current caused to flow to the resistor is changed on the basis of a difference input signal to change common mode voltage, a common mode detection buffer detects a change in the common mode voltage, and the difference signal is reconfigured and outputted. 差動出力バッファの差動入力部に流れる電流の経路に抵抗を配置し、差動入力信号に基づいてこの抵抗に流れる電流値を変えてコモンモード電圧を変化させ、このコモンモード電圧の変化をコモンモード検出バッファで検出して、差動信号を再構成して出力するようにした。 - 特許庁
An emitter grounded circuit 18 having a single circuit analog signal input system converts a voltage signal J1 inputted from an input terminal 18a into a current signal, and is so structured that a signal output from a high frequency oscillator circuit 20 is added to the current signal of the emitter grounded circuit 18 at the time of regeneration. 一系統のアナログ信号入力を備えるエミッタ接地回路18は、入力端子18aから入力された電圧信号J1を電流信号に変換するとともに、再生時に高周波発振回路20から出力される信号がエミッタ接地回路18の電流信号に加算するように構成する。 - 特許庁
The induction heating rice cooker includes capacitance detection means 11 for detecting the change in a capacitance in the resonant capacitor 3 by input from current detection means 8 for detecting an input current supplied by the AC power source 5 and voltage detection means 7 for detecting a peak voltage applied to the switching means 4. 交流電源5より供給される入力電流を検知する電流検知手段8とスイッチング手段4に印加されるピーク電圧を検知する電圧検知手段7からの入力により共振コンデンサ3の静電容量の変化を検知する静電容量検知手段11を備える。 - 特許庁
A sensor output processing part 2 has the current voltage conversion circuit 5 constituted such that the conversion resistor R1 is connected between an inverting input terminal and an output terminal of an operational amplifier OP1, and outputs output voltage Vout which varies according to variation of input current Iin from a photodiode PD. センサ出力処理部2は、演算増幅器OP1の反転入力端子と出力端子との間に変換抵抗R1が接続された構成の電流電圧変換回路5を有し、フォトダイオードPDからの入力電流Iinの変動に応じて変動する出力電圧Voutを出力する。 - 特許庁
The converter sets the amplitude ratio of input current peak value in the discontinuous mode and the continuous mode, and the switching timing of the discontinuous mode and the continuous mode by circuit constants such that the input current from the AC power supply to the full-wave rectifier circuit has a desired two stage waveform. そしてコンバータは、交流電源から整流回路への入力電流波形が所望の2段電流波形となるように、不連続モード時の入力電流のピーク値と連続モード時の入力電流のピーク値との振幅比及び不連続モードと連続モードの切替えタイミングを回路定数により設定する。 - 特許庁
An NPN transistor 4 is provided where a base is connected to an input side of a current amplifier circuit 2 which amplifies an input current to supply it to the base of a transistor 3 at an output stage, an emitter is connected to a ground, and a collector is connected to an output terminal OUT, with a structure comprising a parasitic PNP transistor 5. 入力電流を増幅して出力段のトランジスタ3のベースに供給する電流増幅回路2の入力側にベースが、エミッタがグランドに、コレクタが出力端子OUTにそれぞれ接続されたNPN型のトランジスタ4を設けるとともに、このトランジスタ4をPNP型のトランジスタ5が寄生する構造とする。 - 特許庁
A current path P1 is formed by serially connecting a diode 11 and a resistor 12 (resistor R1) from an input terminal 14A side, a second current path P2 is formed by serially connecting a diode 13, a resistor 14 (resistor R2) and a resistor 15 (resistor R3) from the input terminal 14A side. 電流経路P1は、入力端子14A側から見て、ダイオード11、及び抵抗12(抵抗R1)を直列接続して形成され、第2の電流経路P2は、入力端子14A側からダイオード13、抵抗14(抵抗R2)及び抵抗15(抵抗R3)を直列接続して形成される。 - 特許庁
The electrostatic breakdown protection circuit has: a thyristor for allowing a surge current to flow from an input terminal to the second power terminal; and a bipolar transistor for allowing a surge current to flow from the first power terminal to the input terminal. 静電破壊保護回路は、第1の電源端子、第2の電源端子及び入出力端子を有する半導体装置の静電破壊保護装置であって、前記入力端子から前記第2の電源端子にサージ電流を流すサイリスタと、前記第1の電源端子から前記入力端子にサージ電流を流すバイポーラトランジスタとを有する。 - 特許庁
Even when the level of the DC voltages V1a-V1d is switched, since the same current flows to the 4 terminals 4a-4d, the noise is smaller than a conventional receiver where a current flowing to the signal input output terminals 4a-4d is fluctuated. 直流電圧V1a〜V1dのレベルが切換えられても4つの端子4a〜4dには同一値の電流が流れるので、信号入出力端子に流れる電流が変動していた従来に比べノイズが小さい。 - 特許庁
During charging, the power source circuit charges a capacitor C4 through a resistor R11 by using the input current Ib and controls the charging current, by controlling the turn-on time of the switching transistor Q1 by charging and discharging the capacitor C4. また、充電中に上記入力電流により抵抗R11を通してコンデンサC4を充電し、このコンデンサC4の充放電によってスイッチングトランジスタQ1のオン時間を制御し、充電電流の制御を行う。 - 特許庁
Hereby, since an application current Icc flowing in a resistance R7 is nor fluctuated, even if the current consumption I1 of the signal processing circuit 12 is fluctuated based on the signal level of the input signal Sig1, a voltage drop ΔV can be fixed constant. これにより、入力信号Sig1の信号レベルに基づいて信号処理回路12の消費電流I1が変動しても、抵抗R7を流れる通電電流Iccは変動しないので、電圧降下ΔVを一定にできる。 - 特許庁
In the case that an input current to an inverter device 4 exceeds a specified threshold current at power running, this controller controls a system so that it may supply an inverter device 4 with energy accumulated in an EDLC 7 by switching on a chopper device 6. 力行時において、インバータ装置4への入力電流が所定のしきい値電流を超える場合に、チョッパ装置6をオン状態にして、EDLC7に蓄えられたエネルギーをインバータ装置4に供給するように制御する。 - 特許庁
Current/voltage converting circuits by an arithmetic amplifier and an I/V converting resistance are provided for the necessary number of ranges, and the respective input terminals of the current/voltage converting circuits are separated from each other by the resistance to realize the range switching function. 演算増幅器とI/V変換抵抗による電流/電圧変換回路を必要レンジ数分設け、それらの各電流/電圧変換回路の入力端子間を抵抗で分離してレンジ切り替え機能を実現する。 - 特許庁
A first current controller feeds a current to an output node in response to a first logic level of a first signal and buffers an input voltage to provide an output on the output node in response to a second logic level of the first signal. 第1電流制御部は、第1信号の第1論理レベルに応答して電流を出力ノードに供給し、第1信号の第2論理レベルに応答して入力電圧をバッファリングして出力ノードに出力する。 - 特許庁
To provide set standby radio equipment, capable of observing and performing time coincidence of the delay times that occur in a current/standby system according to the input point of a transmission change-over switch, and to provide its current/standby switching method. 現用/予備系の送信部で発生する遅延時間を送信切替スイッチの入力点相当で観測および時間一致をすることができるようにしたセット予備無線装置およびその現用予備切替方法を提供する - 特許庁
When an alternating current is input to the first and the second electrodes 11 and 12, an electric field is generated at the inner part of the dielectric 10 and an alternating current is output, because the electric field makes the third and the fourth electrodes 13 and 14 generate electric potentials. 第一第二電極11,12に交流が入力されると誘電体10の内部に電界が発生し、この電界が第三第四電極13,14に電位を発生させるので交流が出力される。 - 特許庁
An input control means 18a controls the frequency difference between the high frequency current flowing through the heating coil 10a corresponding thereto and the frequency of the high frequency current flowing through the other heating coil 10b to become higher than an audible frequency. 入力制御手段18aは、対応する加熱コイル10aに流れる高周波電流周波数と、他の加熱コイル10bに流れる高周波電流の周波数差が可聴周波数以上となるよう制御する。 - 特許庁
After a filter circuit 25 processes a discharge current detection signal output from the current probe 24 and a low frequency capacity component and a high frequency noise component are taken out from the signal, the signal is input to a PWM circuit 26. この電流プローブ24から出力される放電電流検出信号をフィルタ回路25で処理して該信号から低周波の容量成分や高周波のノイズ成分を取り除き、PWM回路26に入力する。 - 特許庁
On the basis of the input signal to the base, the NPN junction transistor 108 causes a current supplied from a 5V voltage power source 110 as an amplification current to flow from the collector to the emitter, and it is outputted to an output terminal 109. このベースの入力信号に基づいてNPN接合型トランジスタ108が、増幅電流として5V電圧電源110から供給される電流を、コレクタからエミッタに流し、出力端子109に出力させる。 - 特許庁
As a result, the H level of the PWM signal input in an error amplifier 68 via an RC filter 8 can be made constant, enabling control of the current value to a load, even when the output current to the load 7 becomes a fine value. これにより、RCフィルタ8を介してエラーアンプ68に入力されるPWM信号のHレベルを一定とすることができるため、負荷7への出力電流が微少な値となるときも制御することができる。 - 特許庁
To provide a load driving device of digital control type, capable of using a microcomputer allowing only the input of positive voltage values through simple circuitry, even when the voltage value of a current signal detected at a current detection circuit is a negative value. 簡易な回路構成により、電流検出回路で検出される電流信号の電圧値が負の値であっても、正の値の電圧値しか入力できないマイコンの使用が可能なデジタル制御式負荷駆動装置を提供する。 - 特許庁
A weighting-factor compensating section for compensating a weighting factor, with respect to shaft-torque detection calculated by a mechanical system is provided so as to add an output signal of each compensation section and to input it as a torque current command to a current control section. また、機械系で算出された軸トルク検出に対する重み係数を付与する重み係数補償部を設け、各補償部の出力信号を加算してトルク電流指令として電流制御部に入力する。 - 特許庁
To provide a high-efficiency switching power supply circuit which is capable of precisely performing a constant current control of an output current against fluctuations in input voltage or output voltage in spite of a simple circuit configuration. 簡単な回路構成でありながら、入力電圧あるいは出力電圧の変動に対して出力電流の定電流制御を精度良く行うことが可能であり、かつ効率が高いスイッチング電源回路を提供する。 - 特許庁
A compensation resistor is coupled between an output of the current limit amplifier and the second input of the feedback amplifier for adjusting the reference signal, to compensate for variation in output current of the power conversion circuit. 補償抵抗器は、電流制限増幅器の出力とフィードバック増幅器の第2の入力との間に結合されることによって、基準信号を調節し、電力変換回路の出力電流の変動に対して補償する。 - 特許庁
To solve such a problem that exact detection can not be made owing to saturation when the current of an element is detected by an AC-DC conversion circuit using an ACCT while improving the power factor of AC input current by using a semiconductor switch element. 半導体スイッチ素子を用いて、交流入力電流を高力率化しながら、交流−直流変換する回路で、ACCTを用いて素子の電流を検出すると、飽和により正確な検出ができない。 - 特許庁
In a control section 18 where the dropped welding voltage is detected, the welding current for controlling the heat input quantity constant with respect to the welding voltage is read from the welding voltage-welding current map previously stored in a memory section 19. また低下した溶接電圧を検出した制御部18において、記憶部19に予めメモリした溶接電圧−溶接電流マップから溶接電圧に対して入熱量を一定に制御する溶接電流を読み取る。 - 特許庁
A differential amplifier circuit is configured so as to detect a sense current flowed by a sense transistor, and therefore performs overcurrent protection before an occurrence of output voltage drop even when an input-output voltage difference is small and an output current is large. センストランジスタの流すセンス電流を、差動増幅回路で検出する構成としたので、入出力電圧差が小さく出力電流の多い状態で、出力電圧が降下しなくても過電流保護をかけることができる。 - 特許庁
To provide a voltage controlled oscillation circuit in which manufacturing process variation of an oscillation frequency (bias current) offset which occurs when using a depression type MOS transistor for control voltage input of a voltage/current converting part is corrected. 電圧電流変換部の制御電圧入力用MOSトランジスタにデプレッション型を使用した際に発生する発振周波数(バイアス電流)オフセットの製造プロセスばらつきが補正された電圧制御発振回路を提供する。 - 特許庁
A current-voltage converter circuit 1 converts an input current signal into a voltage signal, and a single-differential converter circuit 2 converts this voltage signal into a differential signal and outputs it. ローパスフィルター3及び4はシングル−差動変換回路2からの出力Q及びQBをそれぞれ入力とし、電圧−電流変換回路5はローパスフィルター3及び4からの出力電圧の差分を電流信号に変換する。 - 特許庁
In an output power limiting circuit 7, a control signal based on a mean value of an ac voltage source from an AC input averaging circuit 6 and currents from current detector circuits 5, 13 is supplied to current limiting circuits 8, 14. 出力電力制限回路7では、AC入力平均化回路6からの交流電圧源の平均値と、電流検出回路5、13からの電流とに基づいた制御信号が電流制限回路8、14へ供給される。 - 特許庁
The DC component removing circuit 28 is structured in such a way as to remove from a current control signal ICs a DC component that causes the DC offset portion to be generated in the AC input current of a controlling and rectifying device 3. 直流成分除去回路29は、制御整流装置3の交流入力電流に発生する直流のオフセット分の発生原因となる直流成分を電流制御信号Icsから除去するように構成する。 - 特許庁
The current flowing between the collector and the emitter of a switching element SW is detected indirectly as a voltage drop amount, caused by a minute current outputted from a sense terminal ST, and is applied to an inversion input terminal of a comparator 30. スイッチング素子SWのコレクタ及びエミッタ間を流れる電流は、センス端子STから出力される微少電流による電圧降下量として間接的に検出され、コンパレータ30の反転入力端子に印加される。 - 特許庁
To provide a vertical deflection circuit capable of generating a vertically deflecting current which linearly changes, even if there is distortion in linearity of input/output characteristics of a D/A converter when a vertically deflecting current is generated digitally. 垂直偏向電流をディジタル的に生成する場合に、D/Aコンバータの入出力特性の直線性に歪みがあっても、直線的に変化する垂直偏向電流を生成できる垂直偏向回路を提供する。 - 特許庁
Then, a reset signal for resetting actions of a constant current control circuit driving a first transistor which supplies current to the LED with an input enable-signal is generated by the protection circuit on the basis of detected results. そして、その検出の結果に基づいて、保護回路により、入力されたイネーブル信号によりLEDに電流を供給する第1のトランジスタを駆動する定電流制御回路の動作をリセットするリセット信号を生成する。 - 特許庁
The input terminal has such a voltage threshold value for the voltage reference terminal that the voltage threshold value is different from the voltage at the current detection terminal by an amount equivalent to the product of the second impedance and the second threshold value for current. この入力端子は、電流検知端子における電圧と比べて第2のインピーダンスと第2の電流しきい値との積に相当する量だけ異なっているような、電圧基準端子に対する電圧しきい値を有している。 - 特許庁
The current control part 30 outputs adjustment current for adjusting Gm values corresponding to each transconductance amplifier to the first Gm-C filter part 32 using a signal output from a central control part 20 as input. 電流制御部30は、中央制御部20から出力された信号を入力として、第1Gm−Cフィルタ部32に対し、それぞれのトランスコンダクタンスアンプに対応した、Gm値を調整するための調整電流を出力する。 - 特許庁
The inductive load driving circuit is constituted by mutually connecting a current control circuit 1, a control voltage generation circuit 2b, a discharge circuit 3 and a level detection circuit 4 between an external control input terminal IN and a current output terminal OUT. 外部制御入力端子INと電流出力端子OUTの間に電流制御回路1、制御電圧発生回路2b、放電回路3、レベル検出回路4を相互に接続して誘導性負荷駆動回路を構成する。 - 特許庁
The entire part of the circuit is divided into input circuits 60, 70 and an output circuit 80 and dividing positions are provided respectively on voltage routes of a first current mirror circuit 11 and a third current mirror circuit 21. また、この発明は、回路全体を入力回路60、70と出力回路80に分割し、その分割位置を、第1カレントミラー回路11および第3カレントミラー回路21のそれぞれの電圧経路上に設けるようにした。 - 特許庁
To enhance voltage boost effect and to reduce power loss when using a method to drive light emitting diodes (LEDs) with a current mirror, especially when driving white light emitting diodes by boosting the voltage at the input end with a current mirror. 電流鏡で発光ダイオード(LED)を駆動する方法に関し、特に、電流鏡で入力端の電圧を増強して白色光ダイオードを駆動するに際し、昇圧効果を向上し、及びパワーの損失を低減する。 - 特許庁
To lessen the current dependence of the output waveform of an optical transmitter, the input amplitude in a light emitting element drive stage according to the pulse current, to thereby stabilize the output waveform and enable low-voltage operation. 本発明は、光送信器の出力波形の電流依存性を減らすため、パルス電流に応じて発光素子駆動段の入力振幅を制御することにより出力波形の安定化を図り、低電圧動作可とする。 - 特許庁
In the logarithmic amplifier, voltage-current conversion of input voltage Vin is performed by a circuit constituted of a differential amplifier 1, a resistor R1 and a MOS transistor Q1 and the transformed current is made to flow in a transistor Q3. この発明は、差動増幅器1、抵抗R1、およびMOSトランジスタQ1からなる回路により、入力電圧Vinの電圧−電流変換を行い、この変換電流がトランジスタQ3に流れるようになっている。 - 特許庁
The gain of the voltage subjected to logarithmic extension with respect to the input voltage is made proportional to a ratio of the 2nd current to the 1st current, so as to provide a gain which is inversely proportional to the absolute temperature. 前記入力電圧に対する前記対数伸長された電圧のゲインを前記第1の電流に対する前記第2の電流の比に比例したものとすることで、絶対温度に反比例したゲインを持つようにしている。 - 特許庁
In registering a password, an image as a hint in registering an authentication password is displayed in a hint image region 701 for authentication in order to let a user to recall a current password to be inputted to a current password input region 702. パスワードを登録する際に、現パスワード入力領域702に入力すべき現パスワードを想起させるために、認証パスワードを登録した際にヒントとしたイメージを、認証用ヒントイメージ領域701に表示する。 - 特許庁
To provide an electronic circuit that limits an inrush input current inside a power source and that limits a short-circuit current, when an DC output of the power source is short-circuited, while suppressing cost and/or complexity of the electronic circuit. 電子回路のコスト及び複雑性の一方又は両方を低減しながら、電源内の突入入力電流を制限し且つ電源の直流出力の短絡時の短絡電流を制限する電子回路を提供すること。 - 特許庁
The class-AB output circuit (80) has a current buffer circuit which inputs the first and second signals as a differential input and amplifies it, and controls a phase compensation capacitance and a current that flows in the phase compensation capacitance. AB級出力回路(80)は、第1信号および前記第2信号を差動入力として増幅し、位相補償用容量および位相補償用容量に流れる電流を制御する電流バッファ回路を備える。 - 特許庁
To provide a current output circuit which stably outputs current signals corresponding to input voltage signals independent of impedance value of an external load containing signal lines, and prevents generation of heat in the output circuit. 信号ラインを含む外部負荷のインピーダンス値に係わらず入力電圧信号に対応した電流信号を安定して出力し、かつ、出力回路における発熱を抑えることのできる電流出力回路を提供する。 - 特許庁
To avoid consumption of useless power and to prevent overheat of a transistor(TR) when a DC voltage at an input terminal is comparatively high by eliminating a delay in an interrupting current of the TR that amplifies a current. 電流増幅するトランジスタの遮断電流の遅延をなくすることにより、無駄な電力の消費をなくすることができ、入力端子の直流電圧が比較的高い場合におけるこのトランジスタの過熱を防止できること。 - 特許庁