If an excitation current induced voltage produced at the transformer is superposed on an input direct-current voltage Vin and applied, it is detected, using a comparator 52 as to whether the voltage between the terminals of the switching element 20 exceeds a specified voltage. スイッチ素子20の端子間には、トランスで生じた励磁電流誘起電圧が入力直流電圧Vinに重畳されて印加される場合、コンパレータ52を用いてスイッチ素子20の端子間電圧が所定電圧を超えているか否かを検出する。 - 特許庁
The filter frequency bandwidth of an input signal of a crystal vibrator 3a of the bandwidth variable filter 1 is freely varied in response to a varied impedance and controlling a current to a PIN diode 3b by a current control section 5 varies this impedance. 帯域可変フィルタ1の水晶振動子3aは、インピーダンスの可変に応じて入力信号の濾過周波数帯域幅を可変自在であり、このインピーダンスはピンダイオード3bに対する電流を電流制御部5で制御して可変する。 - 特許庁
An encoder 100 comprises a segmenter 110 for segmenting an input information word into a plurality of coded segments and an encoder core 120 for calculating a redundancy bit for a current segment using a redundancy bit of an earlier segment than the current segment in the order. 符号器100は、入力情報語を複数のセグメントに分割するセグメンタ110と、今次のセグメントより順序が1つ先行するセグメントの冗長ビットを用いて今次のセグメントの冗長ビットを計算する符号器コア120を備える。 - 特許庁
The output circuit 5 successively supplies the returned DC current to a strobe line Strobe-B, the input circuit 7 further returns it through the terminating resistors RB1 and RB2 and the strobe line Strobe-XB to the output circuit 5 and the returned current is made to flow into the ground. 出力回路5は、前記戻ってきたDC電流を続けてストローブ線Strobe-Bに供給し、前記入力回路7は更に終端抵抗RB1、RB2及びストロー部線Strobe-XBを通じて出力回路5に戻し、この戻った電流はグランドに流される。 - 特許庁
To provide a diode rectifying circuit for generating a sine wave AC input current and reducing the generation of harmonics current of AC power supply frequency only with passive elements of simplified circuit structure, without using high-frequency switching elements. 高周波スイッチング素子を使用せず簡易な回路構成の受動素子だけで、ダイオード整流回路の交流入力電流を正弦波化し、交流電源周波数の高調波電流の発生を低減するダイオード整流回路を提供する。 - 特許庁
To provide a discharge lamp lighting device with a DC-DC converter requiring no input current detecting resistor or no current transformer, realizing miniaturization and a low cost, and capable of being properly controlled at the time of a start and during the stabilization time. 直流−直流コンバータを有した放電灯点灯装置において、入力電流検出用の抵抗あるいはカレントトランスを不要とし、小型化、低価格化を実現するとともに、始動時と安定時とで適正な制御ができるようにする。 - 特許庁
To improve performance, achieve size reduction and price reduction by enabling DC output voltage to be dropped, and dispensing with a rush current suppressing circuit for a smoothing capacitor, in a polyphase voltage type rectifier which turns an AC input current into sine waves. 交流入力電流を正弦波にする多相電圧形整流器において、直流出力電圧を降圧可能とし、かつ、平滑用コンデンサの突入電流抑制回路を不要にして性能を向上させ、小型化、低価格化を図る。 - 特許庁
A frequency ratio digitalization temperature sensor for generating a temperature output signal corrected in linearity has a frequency ratio ADC having an input generating circuit for receiving PTAT current and CTAT current, a data oscillator, and a reference oscillator. 線形性補正した温度出力信号を発生する周波数比デジタル化温度センサーが、PTAT電流とCTAT電流とを受取る入力発生回路及びデータオシレータと基準オシレータとを具備している周波数比ADCを有している。 - 特許庁
To eliminate the influence of the base current of a transistor to greatly reduce error components contained in difference signals in a difference signal detector for detecting the difference signal between two input current signals, using a transistor differential amplifier circuit. 2つの入力電流信号間の差信号をトランジスタ差動増幅回路を用いて検出する差信号検出装置において、トランジスタのベース電流による影響を無くし、差信号に含まれる誤差成分を著しく低減すること。 - 特許庁
To provide an address comparator with decreased current consumption configured to allow current flow only for a short time, in an address signal pulse period, even when an address signal is input thereto for a repair operation. リペア動作のためのアドレス信号が入力されても、アドレス信号パルス期間のうちの短い時間にのみアドレス比較のための電流が流れ、それ以外には電流が流れないようにして、電流消費を減少させたアドレス比較回路を提供する。 - 特許庁
The variable voltage circuit 12 supplies the bias current to the LD 2 based on a supply voltage supplied from the main power source and an instruction signal which is input from a control circuit outside of the semiconductor laser drive circuit 1 to adjust the bias current. 可変電圧回路12は、主電源から供給される電源電圧と、半導体レーザ駆動回路1の外部の制御回路から入力されバイアス電流を調整するための指示信号とに基づいて、LD2にバイアス電流を供給する。 - 特許庁
To restrict a decrease of the effective printing speed of a printer to a minimum by a printing density limit method in which an AC input consumption current is restricted by making good use of characteristics of a change with time of a consumption current due to heating of a printing hammer. 印字ハンマの発熱による消費電流の経時変化する特性を活用し、交流入力消費電流を抑制する印刷密度制限方法により、印刷装置の実効印刷速度の低下を最小限に抑えることにある。 - 特許庁
When the half-wave current carrying is conducted with the same control signal, ON control is conducted with a constant frequency, having a cycle of about 55 Hz equivalent to intermediate of the input frequencies of 50 Hz and 60 Hz, and thereby, the halogen lamp 2 is controlled by half-wave current carrying. 次に同制御信号にて半波通電をする場合、一周期が入力周波数50Hzと60Hzの中間約55Hzの一定周波数でオン制御を行うことで、ハロゲンランプ2の制御を半波通電する。 - 特許庁
A current display position or current display area stored in the memory controller 5 is changed on the basis of an input from a remote controller or an operation part 12 such as a GUI and then the display position or display area can be changed. メモリコントローラ5内に記憶されている現在の表示位置又は現在の表示領域を、例えば、リモコン又はGUIなどの操作部12からの入力に基づいて変更することにより、表示位置又は表示領域の変更することができる。 - 特許庁
Either a first output transistor Q7 or a second output transistor Q8 is made to perform active operations corresponding to the input signal by a bias current corresponding to the difference in current that occurs, on the basis of the operations of the differential circuit 4 and the load circuit 5. この差動回路4と能動負荷回路5の動作に基づいて生じる電流差に相当するバイアス電流よって、第1と第2の出力トランジスタQ7、Q8のいずれか一方に、入力信号に応じた能動的な動作を行わせる。 - 特許庁
Drive pulses output from a drive circuit 18 are applied on the piezo-electric element 11, electric current flows through the electrode 15a being capacitively coupled to the moving member, and the amount (i) of current is detected by a detecting circuit 19 and input to a control circuit 17. 駆動回路18からの駆動パルスは圧電素子11に印加されると共に移動部材に静電容量結合している電極15aにも流れ、その電流iは検出回路19で検出され、制御回路17に入力される。 - 特許庁
The time constant is controlled by increasing the number of turns of the coil in a stepping motor and increasing the level of an input current to the stepping motor so that the chopping region is not used at the time of constant current driving thus reducing high frequency noise. ステッピングモータのコイルの巻線数を増加することにより、また、ステッピングモータに入力する電流値を増加することにより、時定数を操作して定電流駆動時のチョッピング領域を使用しないようにし、高域騒音を減少させる。 - 特許庁
Upon the end of the welding, the welding current I reduces at a fixed ratio from a welding position X3, a termination current IE is retained from a welding position X4, and the heat input to the base metal 100 progresses in a state of being short compared with the stationary state. 溶接終了時には溶接位置X3から溶接電流Iが一定の割合で減少し溶接位置X4からは終端電流IEが維持され母材100への入熱が定常状態に比して不足する状態で推移する。 - 特許庁
In addition, a superposed control circuit 42 which makes an electric current flow to the superposed circuit 2 by turning on a phototransistor 46 only when the circuit 42 becomes a lightload or high-input voltage state and the current flowing to the circuit 2 becomes smaller than a set value is provided. また、回路が軽負荷や高入力電圧の状態となり、回路電流が設定の電流値よりも低下したときのみフォトトランジスタ46をスイッチオンさせ、重畳回路2に電流を流す重畳制御回路42が設けられる。 - 特許庁
An inductor 4 stores magnetic energy by the current from an input power supply 1 when the switch element 2 is in the conducting state and discharges the magnetic energy by a current being outputted from the diode 3 when the switch element 2 is in the interrupted state. インダクタ4は、スイッチ素子2が導通状態のときに入力電源1からの電流によって磁気エネルギーを蓄積し、スイッチ素子2が遮断状態のときにダイオード3が出力する電流によって当該磁気エネルギーを放出する。 - 特許庁
The control part 4 inputs a voltage and a current generated at a tertiary winding 53 of the transformer 5, and controls a base current of the switching element 3 on the basis of the input value so that at least either of the amplitude or the frequency of a secondary winding 52 of the transformer 5 is varied. 制御部4は、トランス5の3次巻線53で発生する電圧、電流を入力し、この値に基づき、トランス5の2次巻線52の振幅と周波数の少なくとも一方が変化するよう、スイッチング素子3のベース電流を制御する。 - 特許庁
The auxiliary machine ambient temperature in an engine room is measured by a water temperature sensor or an outside air temperature sensor, and a carrying electric current is estimated by predicting a resistance change in the electromagnetic coil 23, and the duty ratio of an input electric current to the electromagnetic coil 23 is calculated. 水温センサまたは外気温センサでエンジン室内の補器周囲温度を測定して、電磁コイル23の抵抗変化を予測することにより通電電流を推定し、電磁コイル23への入力電流のデューティ比を算出する。 - 特許庁
Reference circuits (A2, Q3, Q4) are provided with first and second resistive elements (RH, RL) for applying the reference current to the second input node (75) of the differential amplifier to provide a reference value to be compared with the sense current to determine the state of the memory cell (RM). 基準回路(A2,Q3,Q4)は、差動増幅器の第2の入力ノード(75)に基準電流を加えるための第1と第2の抵抗素子(R_H,R_L)を備え、メモリセル(R_M)の状態を判定するためにセンス電流と比較される基準値を提供する。 - 特許庁
Thus, the gate voltage control circuit detects drain current when non-input is detected as idling current, makes it match with the normal value and can automatically return the characteristic to an original one even if it is changed with the lapse of time. したがって、ゲート電圧制御回路は、無入力が検出されたときのドレイン電流をアイドリング電流として検出し、それを規定値に一致させ、時間の経過による変化があっても特性を自動的に元に戻すことができる。 - 特許庁
The current value after the rectification treatment and the ground fault detection level output from a ground fault detection level calculator 73 are input into a comparator 74, and in the comparator 74, the ground fault detection level and the current value after the rectification treatment are compared to output the result of comparison. 前記整流処理後の電流値と地絡検出レベル演算器73から出力される地絡検出レベルが比較器74に入力され、比較器74では、地絡検出レベルと整流処理後の電流値を比較し、その結果を出力する。 - 特許庁
This information processing system receives the input of the contract contents of the current insurance of the customer and the attributes of the customer, and selects the contract contents of the new insurance according to the inputted contract contents of the current insurance based on the correspondence information. 情報処理システムは、顧客の現在の保険の契約内容および顧客の属性の入力を受け、対応情報に基づき、入力された現在の保険の契約内容に応じて、新しい保険の契約内容を選択する。 - 特許庁
A current control transistor operating in a linear area is disposed serially with the driving transistor, and a video signal for transmitting a signal of emission or non-emission of the pixel is input to a gate of the current control transistor via a switching transistor. 前記駆動用トランジスタと直列に線形領域で動作する電流制御用トランジスタを配し、スイッチング用トランジスタを介して画素の発光、非発光の信号を伝えるビデオ信号を前記電流制御用トランジスタのゲートに入力する。 - 特許庁
Since current-voltage conversion is performed, using an FET for resistance substitution to memory effect of current mode which uses a GTO thyristor, a device is made smaller than S-RAM, in terms of the occupancy area and also is made shorter than D-RAM, in terms of data input/output time. [解決手段]GTOサイリスターを使って電流モードのメモリ効果を抵抗代用のFETで電流−電圧変換する事でS−RAMよりも占有面積を小さく、また、D−RAMよりもデータ入出力時間を縮くする。 - 特許庁
The lamp discriminating circuit 7 is provided with an input current detecting means composed of a current transformer CT and a resistance R3, and a comparator CP1 for comparing end-to-end voltage VR3 of the resistance R3 with a reference voltage value determined by a DC voltage source E1. ランプ判別回路7は、カレントトランスCT、抵抗R3などからなる入力電流検出手段と、抵抗R3の両端電圧V_R3と直流電圧源E1により決まる基準電圧値とを比較する比較器CP1とを備える。 - 特許庁
The first part of current flows through a large size induction coil (L50) and the first rectifier (Gm), while the second part of current is tapped before it flows the large induction coil in the input side and flows through the second rectifier (Ga). 電流の第1の部分は、大きい誘導コイル(L50)及び第1の整流器(Gm)を介し流され、電流の第2の部分は、入力側において大きい誘導コイルを通る前にタップされ第2の整流器(Ga)を介し流される。 - 特許庁
Also, when a control signal for instructing the stop of the reproducing operation is received from the operation input part 14, the supply of the sense current by the sense current supply part 11 is stopped, and the driving of the drum motor 34 is stopped to stop the rotary drum 31. また、操作入力部14からの再生動作停止を命令する制御信号を受信すると、センス電流供給部11によるセンス電流の供給を停止させ、ドラムモータ34の駆動を停止させて回転ドラム31を停止させる。 - 特許庁
To provide an overcurrent protection circuit and a DC power supply device which is hardly affected by the fluctuation of a process or device, wherein the drop of an input voltage and an output voltage can be reduced, and the maximum current value and a short-circuit current value can be set. 本発明は、プロセスやデバイスのばらつきに影響を受け難く、入力電圧と出力電圧のドロップが小さく、最大電流値、短絡電流値を設定可能な過電流保護回路及び直流電源装置を提供する。 - 特許庁
An input resistance R1 has its resistance value set corresponding to the current value of a standby current of the two-wire type sensor 3, so even when the two-wire type sensor 3 is off, electric power which is large enough to drive the two-wire type sensor 3 is supplied. 入力抵抗R1は、二線式センサ3の待機電流の電流値に応じた抵抗値に設定されているから、二線式センサ3がオフ状態のときでも、その二線式センサ3が駆動するのに必要な電力を供給される。 - 特許庁
When the latitude/longitude information of the current location and the retrieval conditions of the nearest facility are input from a user, a retrieval range with the current location as a center is expressed with the character string constituted of "0" and "1" based on the location of the mesh partition on the mesh-shaped map. ユーザから現在位置の緯度経度情報と最寄り施設の検索条件が入力されると、現在位置を中心とした検索範囲を、メッシュ状の地図のメッシュの区画の位置に基づいた“0”と“1”からなる文字列で表す。 - 特許庁
A corrected current Ic adjusted so that two monitored currents I1 and I2 having a predetermined ratio are generated in a corrected current generating circuit 5, and input to one end of a series circuit Nk of resistors 12-1 to 12-(k-1). 補正電流生成回路5において、当該モニタされた2つの電流I1およびI2が所定の比を有するように調節した補正電流Icが生成されて、抵抗12−1〜12−(k−1)の直列回路の一端Nkに入力される。 - 特許庁
A bias voltage BIAS to be input to the clamp NMOS transistor 102 can be set high and the drain voltage of the memory cell 101 can also be high, and hence a current value of the memory cell 101 becomes larger and the speed of sensing a current of a sense amplifier circuit 104 is improved. クランプ用NMOSトランジスタ102のバイアス電圧BIASが高く設定ででき、メモリセル101のドレイン電圧も高くなるので、メモリセル101の電流値が多くなり、センスアンプ回路104の電流センス速度が向上する。 - 特許庁
A bias circuit 36 adjusts bias voltage impressed on an input terminal of the amplifier 26 so that bias current is converged to a fixed value by a predetermined time coefficient to fluctuation of the bias current in an output terminal of the amplifier 26. バイアス回路36は、増幅器26の出力端子におけるバイアス電流の変動に対して、このバイアス電流を所定の時定数で一定値に収束させるように増幅器26の入力端子に印加するバイアス電圧を調整する。 - 特許庁
This suppresses the variation in the current I0 flowing in the series circuit, and regardless of the variation in input voltage VI, a value of the current I0 of the series circuit is held approximately constant, and a constant voltage VO can be outputted. これにより、直列回路に流れる電流I0の変動が抑制され、入力電圧VIの変動に拘らず直列回路の電流I0の値がほぼ一定に保持され、一定の出力電圧VOを出力することができる。 - 特許庁
When a user touches a sensor of the sensor module 60a, the control part 100 carries current only to the touched sensor and sensors in the vicinity thereof to receive an input from the user, and does not carry current to the remaining sensors on the same sensor module. ユーザがセンサモジュール60aのセンサに触れると、制御部100は、触れているセンサとその近傍のセンサだけに通電して、ユーザからの入力を受け付けるようにし、同一センサモジュール上の残るセンサについては通電しないようにしたものである。 - 特許庁
To provide a semiconductor device including a starting circuit for starting an object circuit when input voltage reaches a designated threshold and an input voltage detecting circuit for detecting and determining the input voltage, that can reduce the chip size and consumption current without lowering of input voltage detection accuracy. 本発明は、入力電圧が所定の閾値に達してから対象回路に起動をかける起動回路と、入力電圧の検出判定を行う入力電圧検出回路と、を有して成る半導体装置において、入力電圧検出精度を低下させることなく、チップサイズ縮小や消費電流低減を図ることが可能な半導体装置を提供することを目的とする。 - 特許庁
Or, the denominator and the numerator of the function are respectively composed by output currents of a MOS differential pair and a quadritail cell (four transistors are driven by a common tail current; outputs of two transistors to which the differential input voltage is input, are commonly connected; and outputs of two transistors, to which the common mode voltage of the differential input voltage is input, are connected in common). あるいは、前記関数の分母および分子がそれぞれMOS差動対とクァドリテールセル(4つのトランジスタが共通のテール電流で駆動され、差動入力電圧が入力される2つのトランジスタの出力が共通接続され、差動入力電圧のコモンモード電圧が入力される2つのトランジスタの出力が共通接続される)の出力電流から構成される。 - 特許庁
This amplifier circuit comprises a first operational amplifier having a negative input terminal, a positive input terminal and an output terminal, a photodiode connected to the negative input terminal, a first resistor inserted between the output terminal and the negative input terminal, and a second resistor inserted between the output terminal and the positive input terminal, and a current is outputted from the output terminal through the second resistor. 本発明の増幅回路は、負入力端子と正入力端子と出力端子とを有する第1の演算増幅器と、前記負入力端子に接続されたフォトダイオードと、前記出力端子と前記負入力端子の間に挿入された第1の抵抗と、前記出力端子と前記正入力端子の間に挿入された第2の抵抗とを備え、前記出力端子から前記第2の抵抗を介して電流を出力する。 - 特許庁
On the other hand, when the power source input and output ends connected to a power source voltage detecting end REF- has a positive polarity, the switch SW passes the current flowing from the secondary battery B to the power source input and output ends through the resistor R. 一方、電源電圧検出端REF−が接続された方の電源入出力端が正極性であるとき、スイッチSWに、二次電池Bから抵抗器Rを介してこの電源入出力端へと流れる電流を通過させる。 - 特許庁
To provide an input circuit in which a high level of an output signal voltage is set around a power supply voltage of a CMOS inverter when an output signal of the CMOS inverter at an input first stage is at a high level and a through-current is decreased. 入力初段のCMOSインバータの出力信号がハイレベル時の当該出力信号電圧をCMOSインバータの電源電圧程度にすることができると共に、貫通電流を小さくすることができる入力回路を提供する。 - 特許庁
The electromagnet 70 is arranged outside a wall part 23a formed in the input rotary member 20, and moves in the axial direction by magnetic attraction force acting between the wall part 23a of the input rotary member 20 and itself by current-carrying to a coil 72. 電磁石70は、入力回転部材20に形成された壁部23aの外側に設けられ、コイル72への通電により入力回転部材20の壁部23aとの間で作用する磁気吸引力により軸線方向に移動する。 - 特許庁
After that, operations of the semiconductor circuit to be verified are simulated by using the circuit diagram data and the input data in steps S2 to S10 and everchanging voltage values, current values in input terminals, etc., of the respective circuit elements are stored on the memory. その後、ステップS2〜S10において前記回路図データと入力データとを用いて被検証半導体回路の動作をシミュレーションし、各回路素子の入力端子などでの時々刻々の電圧値、電流値を前記メモリ上に格納する。 - 特許庁
When the level of the input signal is increased exceeding a prescribed value, the attenuator 3 is connected to input signal lines 9a and 9b, the signal level is lowered by the attenuator 3, the base voltage of transistors 8a and 8b is raised and a base current is increased. 入力信号のレベルが所定値を超えて上昇したとき、減衰器3を入力信号線路9a、9bに接続し、減衰器3によって信号レベルを下げると共にトランジスタ8a、8bのベース電圧を上げてベース電流を増す。 - 特許庁
The first and second input legs have non-complementary structures having associated therewith a variable parameter, e.g., a variable resistance, variable current or variable voltage, having a value that is a function of a corresponding input signal. 第1および第2の入力枝は、お互いに対して非相補構造を有し、非相補構造は各々、それと関連して、対応する入力信号の関数となる値を有する可変パラメータ、例えば可変抵抗、可変電流、可変電圧を有する。 - 特許庁
A non-inversion input terminal of the comparator CMP 1 of the reverse current prevention circuit 5 is connected to the correction voltage source V_CC1 outputting correction voltage V_C1 lower than GND, and an inversion input terminal is connected to the output part of the switching circuit 3. 逆電流防止回路5のコンパレータCMP1の非反転入力端子は、GNDよりも低い補正電圧V_C1を出力する補正電圧源V_CC1に接続され、反転入力端子はスイッチング回路3の出力部に接続されている。 - 特許庁
To prevent the generation of an excessively large input current when a pantograph is reattached to an overhead wire even if capacities of input filter capacitors are increased in order to elongate a power-supply possible time when the pantograph is separated from the overhead wire. パンタグラフが架線から離線した場合の電力供給可能時間を延長するために入力フィルタコンデンサの容量を増加した場合でも、パンタグラフが架線に再着線した場合に過大な入力電流を防止することである。 - 特許庁