In case of the maximum gain upon no input and infinitesimal signal, as for the detecting wave circuit 3 output, only a detecting wave current of the variable gain amplifier 2 output restricted appears for the constant current I, the maximum gain of the variable gain amplifier 2 is restricted, the gain is increased compared with the case where no constant current I exists, and an excellent receiving sensitive characteristic is obtained without generating an output noise. 無入力,微小信号時に最大利得の場合、検波回路3出力は定電流Iの分、制限された可変利得増幅器2出力の検波電流のみ現れ、可変利得増幅器2の最大利得は、定電流Iが無い場合に比べて制限され利得が増大し、出力ノイズを発生させずに良好な受信感度特性を得る。 - 特許庁
Furthermore, the controller 37 executes torque variation zero control for controlling a current vector of the AC motor 14 so that the deviation between a first estimated torque, obtained from a motor detection current vector of the AC motor 14 and a second estimated torque, obtained from a command current vector for torque control becomes substantially zero, thereby preventing unpleasant torque variations in the transition of the input power control of the MG unit 30. 更に、交流モータ14のモータ検出電流ベクトルから求めた第1の推定トルクとトルク制御用の指令電流ベクトルから求めた第2の推定トルクとの偏差が略ゼロとなるように交流モータ14の電流ベクトルを制御するトルク変動ゼロ制御を実行することで、MGユニット30の入力電力制御の過渡時に不快なトルク変動を防止する。 - 特許庁
Because of the extreme increase of the current value when the electrolytic cleaning is performed with a large amount of a detergent remaining in the laundry caused by the accidental input of the detergent and the resultant increase of detergent concentration in washing water during the electrolytic washing cycle or the like, the operation of the electrolysis device is stopped halfway through the electrolytic washing because the power supply current exceeds the upper limit current value. この電解洗い行程において、使用者によって誤って洗剤が投入され、洗濯物に洗剤分が多く残ったまま電解洗いが行われ、洗い水の洗剤濃度が高くなるなどの原因により、通電電流値が非常に大きくなった場合には、通電電流が上限電流値を超えるため、電解洗いの途中で電解装置の動作が中止される。 - 特許庁
The driving circuit 3 sets off a semiconductor element when a cutoff circuit constituting the semiconductor device 4 with the overheat protection function cuts off input of the semiconductor element, changes the driving voltage to specified voltage so that the driving electric current exceeds the threshold value electric current and holds the driving voltage at the specified voltage while the detection signal is output from the electric current detection circuit 2. 駆動回路3は、過熱保護機能付き半導体装置4を構成する遮断回路が半導体素子の入力を遮断した場合には、半導体素子をオフするとともに、駆動電流がしきい値電流を超えるように、駆動電圧を所定の電圧に変化させ、電流検知回路2から検知信号が出力されている間は、駆動電圧を所定の電圧に保持する。 - 特許庁
Since the gain control and bias current control of the second variable gain amplification circuit 2 can be separately performed by this constitution, the consumption current can be reduced without deteriorating the input intercept point because the current of the second variable gain amplification circuit 2 is lowered as the gain of the first variable gain amplification circuit 1 of a front stage is lowered and output signal strength is lessened. この構成により、第2の可変利得増幅回路2の利得制御とバイアス電流制御を別々に行うことができるため、前段の第1の可変利得増幅回路1の利得が下がり出力信号強度が小さくなるにつれ第2の可変利得増幅回路2の電流を下げるため、入力インターセプトポイントを劣化させずに消費電流を低減することができる。 - 特許庁
A switching current idac is set for the sum of a luminescence current iη and an offset current iof by a DAC operating circuit 17, a second switch circuit 18 is turned on when a laser diode LD is lighting and turned off when the laser diode LD is unlighting by an external data signal Sd inputted from a DATA input terminal 33. DAC演算回路17によって、発光電流iηにオフセット電流iofを加えた電流にスイッチング電流idacが設定され、DATA入力端子33から入力される外部からのデータ信号Sdによって、レーザダイオードLDの点灯時は第2スイッチ回路18をONさせ、レーザダイオードLDの消灯時は第2スイッチ回路18をOFFさせる。 - 特許庁
To prevent the insulation of an input gate in an internal circuit from being destroyed by a voltage drop of a ground line caused by a surge current in an LSI adopting a ground line separation technology and a plurality of power sources thereto. 接地線分離技術および複数電源を採用したLSIにおいて、サージ電流による接地線の電圧降下に起因する内部回路の入力ゲートの絶縁破壊を防止する。 - 特許庁
To provide a broadcast receiver and broadcast display method with which user convenience is improved by enabling next program information of a current channel to be displayed on a screen without input operation by a user. ユーザによる入力操作無しで、現材のチャンネルの次番組情報を画面に表示するようにして、ユーザの利便性を向上させた放送受信装置および放送表示方法を提供する。 - 特許庁
A signal-amplifying means is mounted to a self-switching drive circuit and, a positive feedback circuit, a timing circuit, a feedback circuit and a current-control circuit are disposed in parallel and connected to an input part of the means. 自励方式のスイッチング駆動回路において、信号の増幅手段を設け、その入力部に正帰還回路、タイミング回路、フイードバック回路及び電流制限回路を並列して接続した。 - 特許庁
Input-side and output-side switching circuits 14 and 15 switch uses of the high-speed control circuit 12 and the low-current control circuit 13 according to a switching signal F. 入力側切替回路14および出力側切替回路15は、切替信号Fに応じて、高速用制御回路12を使用するか、または低電流用制御回路13を使用するかを切り替える - 特許庁
In addition, the power source of a voltage/current conversion circuit 18 on the device side contacting with the living body 26 of the main circuit 1 is turned on and off with an input signal of the device side generating the electrical stimulation signal. また、主回路1の、生体26に接触する装置側にある電圧・電流変換回路18の電源を、電気刺激信号を発生する装置側の入力信号によってオンオフするようにした。 - 特許庁
The input/output current and voltage of a battery are sampled at the lapse of each fixed time by a sensor (S150), and an experimental expression for predicting the battery voltage is obtained, based on the sampled time-series data (S160). 電池の入出力電流と電圧をセンサにより一定時間経過毎にサンプリングして(S150)、そのサンプリングした時系列データに基づいて、電池電圧を予測する実験式を求める(S160)。 - 特許庁
Then the magnetic material thin film 3 is coupled to a power supply unit 5 having an input terminal for supplying element current, and the detector 20 detects an output at both ends of the magnetic material thin film 3. そしてこの磁性体薄膜3に素子電流を供給する入力端子を備えた給電部5が接続され、検出部20において磁性体薄膜3両端の出力が検出される。 - 特許庁
When time inputted from the input means 51 by the clerk is coincident with the current time displayed in the second closing operation confirmation picture, the closing processing command is transmitted to respective play stand terminals. そして、係員が入力手段51から入力した時間が第2の閉店操作確認画面に表示している現在時間と一致すると、各遊技台端末に閉店処理指令を送信する。 - 特許庁
The potential difference between terminals of a series resistance 11 where the control current Ia of the variable attenuator 2 passes through, is received by voltage followers 12, 13 of high input impedance, and amplified by a differential amplifying part 14. 可変減衰器2の制御電流Iaが通過する直列抵抗11の端子間電位差を高入力インピーダンスのボルテージフォロワ12,13で受け、差動増幅部14により増幅する。 - 特許庁
To provide a resistor film type transparent analog touch panel capable of reducing power consumption by switching off a current during a stand-by state, and increasing resolution to locate the position of input. 入力位置分解能を高くするとともに、入力待機状態には電流を流さないようにして消費電力を低減することができる抵抗膜式透明アナログ型タッチパネルを提供する。 - 特許庁
When the short-circuit current flows in the sensor input circuit 22, the high potential route LH is set to be in an opening state by stopping an operation of the relay RY based on the output of the short-circuit detecting circuit 50. このセンサ入力回路22において短絡電流が流れた場合、短絡検出回路50の出力に基づいて、リレーRYの動作が停止して高電位経路LHが開いた状態となる。 - 特許庁
To prevent an abnormal through-current from flowing in an input output circuit that converts a voltage level of a signal that is given/received between circuits driven by respective power supplies with two different voltage levels. 異なる二つの電位レベルの電源電圧で駆動される回路間で授受される信号の電圧レベル変換を行う入出力回路において、異常な貫通電流が流れるのを防ぐこと。 - 特許庁
When a second transistor Tr12 is selected according to the control signal SW, the second transistor Tr12 amplifies a second input signal IN2, so that a current flows in a first resistor RLC1. 制御信号SWにより第2のトランジスタTr12が選択されると、第2のトランジスタTr12が第2の入力信号IN2を増幅し、第1の抵抗RLC1に電流が流れる。 - 特許庁
To sufficiently exhibit the power consumption reduction effect at light load by enabling the estimation (detection) of a load current by so arranging the constitution as not to be affected by input voltage in a switching power unit. スイッチング電源において、入力電圧の影響を受けないようにして負荷電流の推定(検出)を可能とし、軽負荷時における消費電力の低減効果を十分に発揮できるようにする。 - 特許庁
A maintenance person rushes to a block where the detector 5 detected an abnormality and detects an abnormal unit by applying a removable current sensor to the input line of the units sequentially. 検出器が異常を検出したブロックへ保守要員が急行し、順次ユニットの入力線に着脱式の電流センサーを装着してどのユニットに異常があるかを検出するようにした。 - 特許庁
To provide a receiving front end circuit of low current consumption in which an IF output level is not remarkably lowered even under an unexpected strong input condition, and a receiving circuit for not generating errors in receiving level detection. 想定外の強入力条件下でもIF出力レベルが著しく低下しない、低消費電流の受信フロントエンド回路と、受信レベル検出で誤差が生じない受信回路を提供する。 - 特許庁
The potential of the capacitive element (19) is input to a gate potential of the drive transistor (Tr10) in a light emission element drive period to control the brightness of the capacitive element (9) with the value of current flowing at this time. 発光素子駆動期間にその容量素子(19)の電位を駆動トランジスタ(Tr10)のゲート電位に入力し、そのときに流れる電流値で発光素子(9)の輝度を制御する。 - 特許庁
To provide a level shift circuit, which prevents a through-current from generating in a circuit at a latter stage, due to shifting to a middle level, even when the drop in the power voltage for giving an input signal level. 入力側の信号レベルを与える電源電圧が低下しても、中間レベルに起因して後段側の回路で発生する貫通電流を防止することができるレベルシフト回路を提供すること。 - 特許庁
Despite this, there is no need for a general user to manually input the current location data PP to the portable communication terminal 100, nor for the portable communication terminal 100 to indispensably have the GPS function. それでいて、その現在位置データPPを一般ユーザが携帯通信端末100に手動入力する必要がなく、携帯通信端末100がGPS機能を必須とすることもない。 - 特許庁
An Nch MOS transistor at an input side of a current mirror 70 is functioned as a voltage operating point setting section to always stabilize a level of a pixel signal (a voltage of a horizontal signal line 20) around a GND level. カレントミラー70の入力側のNchMOSトランジスタQ71を電圧動作点設定部として機能させ、画素信号線電位(水平信号線20の電圧)をGND付近で常に安定にする。 - 特許庁
To obtain a CMOS inverter circuit in which off-leak current of individual transistors is prevented, while achieving power consumption, by sensing an input signal and controlling the substrate potential of a transistor forming a CMOS invertet section in real time. 入力信号を感知しリアルタイムにCMOSインバータ部を形成するトランジスタの基板電位を制御し、トランジスタ個々のオフリーク電流を防止するとともに、低消費電力化を実現する。 - 特許庁
By having the diode 44 provided, the input IGBT is turned on, and an electric current flows to the diode 44 that would have passed from the drift region 54 to the source region 61 of the NMOS via a p-well 60. ダイオード44を設けることにより、入力IGBTがオンしてドリフト領域54からP−ウエル60を介してNMOSのソース領域61に流れる電流が、ダイオード44を流れる。 - 特許庁
A charge-period determination part 18 compares a crank angle with a charge period so as to input a charge control signal to an AND gate 104, when it is determined that a current crank angle lies within a scheduled charge period. 充電期間判定部18は、クランク角と充電期間とを比較して現クランク角が予定の充電期間であると判断したときに充電制御信号をアンドゲート104に入力する。 - 特許庁
To detect whether a switch sub-station supplies a drive current to an input coil of a zone switch when the zone switch for a power distribution line is set to automatic mode from manual mode. 配電線用区分開閉器を手動モードから自動モードに切り換えたときに、開閉器子局が区分開閉器の投入コイルに駆動電流を流しているか否かを検出することができるようにする。 - 特許庁
For the custom IC 10, the current supply capacity of a pull-up circuit 11 is set sufficiently large for the number of switches SW_1-SW_M performing status determination (i.e., the number of input terminals 10b). カスタムIC10は、状態判定を行うスイッチSW_1 〜SW_M の数(即ち、入力端子10bの個数)に対してプルアップ回路11の電流供給能力を十分に大きく設定しておく。 - 特許庁
To provide a method of calculating power in power control devices capable of determining I/O power values without using current detectors of input units and voltage detectors of output units. 入力部の電流検出器、出力部の電圧検出器を用いることなく入/出力電力値を求めることができる電力制御装置における電力算出方法を提供する。 - 特許庁
Thus, since the current is prevented from flowing in a choke coil L inserted between the DC power supply 4 and the inverter 3, a variation in an input supply voltage of the inverter 3 is suppressed in a conduction stop. これにより、通電停止時に、直流電源4とインバータ3との間に挿入されたチョークコイルLに電流を流さないようにし、インバータ3の入力電源電圧の変動を抑制する。 - 特許庁
Thus, both the difference between the collector currents of the NPN transistors Q_1, Q_3 and the difference between the collector currents of the NPN transistors Q_6, Q_8 are equal to the current of a balanced high-frequency input. こうして、npnトランジスタQ_1とQ_3の各々のコレクタ電流の差と、npnトランジスタQ_6とQ_8の各々のコレクタ電流の差とが、いずれも、平衡な高周波入力の電流に等しくなる。 - 特許庁
To provide a built-in phase control digital protection relay device in which phase control and phase synchronization control can be realized by processing input signals of a current digital protection relay device. 現状のディジタル保護リレー装置の入力信号を処理することで位相制御や位相同期制御などを実現することができる位相制御内蔵ディジタル保護リレー装置を提供する。 - 特許庁
A tracking servo control circuit contains a first operation mode for setting the output current of the tracking actuator driving circuit to generally zero and a second operation mode for supplying a predetermined potential to the input. トラッキングサーボ制御回路に、トラッキングアクチュエータ駆動回路の出力電流を略0にする第1の動作モードと、その入力に所定の電位を供給する第2の動作モードを設ける。 - 特許庁
The switching regulator (100) comprises a transconductance error amplifier (110) which compares an output voltage (VOUT) with a reference voltage (VF), and outputs its differential input voltage (Vi) as a current (i110). スイッチングレギュレータ(100)は、出力電圧(VOUT)を基準電圧(VF)と比較して、その差動入力電圧(Vi)を電流(i110)として出力するトランスコンダクタンス誤差増幅器(110)を備える。 - 特許庁
A time averaging part 10 of the image signal processor 1 uses an input image signal Sin(t) of a plurality of frames up to a current frame to generate a time averaged image signal <Sin(t)>. 画像信号処理装置1の時間平均化部10は、現フレームまでの複数フレームの入力画像信号Sin(t)を用いて、時間平均化された画像信号<Sin(t)>を生成する。 - 特許庁
The location of the maximum inductive coupling of the radio frequency to the plasma is mainly determined by the output capacitor, while the input capacitor is mainly used to adjust current magnitude into each coil. プラズマへの高周波の最大誘電結合の場所は、主として出力側コンデンサによって決定され、入力側コンデンサは、主として各コイルへの電流の大きさを調整するために使用される。 - 特許庁
A SBW-ECU 31 controls a driving current to be supplied to a motor 33 at one of a plurality of set values with a shift range selecting pattern input from a range selector 14. SBW−ECU31は、レンジセレクタ14から入力されるシフトレンジの切換パターンによってモータ33へ供給する駆動電流の大きさを複数の設定値のいずれかに制御している。 - 特許庁
When the print key is operated, from the manufacturing date and a current date input from a calendar device 22, the number of days elapsed D is computed, a maximum density fluctuation is obtained for each of Y, M and C. プリントキーを操作すると、前記製造年月日とカレンダー装置22から入力される現在の日付とから製造経過日数Dが算出され、Y,M,C毎の最大濃度変動量が求められる。 - 特許庁
For harmonic current restraining reactors 5a, 5b provided for respective rectifying the filtering circuits 4a, 4b, by selectively and individually setting the inductance that the peaks of input currents do not overlap. 各々の整流平滑回路4a、4bに設けられる高調波電流抑制リアクトル5a、5bは、入力電流のピークが重ならないようなインダクタンス値を個別に選択して設定される。 - 特許庁
The addition circuit 4 comprises one or more MOS transistors and has a function to add the output signal from the output terminal 2a of the current amplifier GM1 and the input signal X. 加算回路4は、1つ以上のMOSトランジスタによって構成され、電流アンプGM1の出力端子2aからの出力信号と入力信号Xとが足し合わされる機能を有する。 - 特許庁
A differential amplifier circuit 12 amplifies a difference voltage between an input voltage Vin and an output voltage Vout, and an output circuit 17 outputs a current in response to an output voltage Va of the differential amplifier circuit 12. 差動増幅回路12は、入力電圧Vinと出力電圧Voutとの差電圧を増幅し、出力回路17は差動増幅回路12の出力電圧Vaに応じた電流を出力する。 - 特許庁
To provide a method for manufacturing a nonaqueous electrolyte secondary battery electrode plate which has high adhesion between a current collector and an electrode active material layer and high long-term storage ability and excels in output-input characteristics. 集電体と電極活物質層との密着性、長期保存性が高く、かつ出入力特性に優れる、非水電解液二次電池用電極板の製造方法を提供すること。 - 特許庁
A reference voltage setting circuit 27 varies the value of reference voltage Vr according to the current detection signal Vd and supplies an obtained reference voltage signal Vr1 to the input end (-) of a comparator 121. 基準電圧設定回路27は、電流検出信号Vdにより、基準電圧Vrの値を変え、得られた基準電圧信号Vr1を、比較器121の入力端(−)に供給する。 - 特許庁
An ignition signal input terminal G, a primary coil connecting terminal C, a GND terminal E and a primary current detection signal output terminal S for connecting to a chip outside are disposed on one chip 100. ワンチップ100に、チップ外部と接続するための点火信号入力端子G,一次コイル接続端子C,GND端子E,一次電流検出信号出力端子Sが配設されている。 - 特許庁
The semiconductor switch 103 becomes the ON state upon input thereto of the Hi-level power switching signal 112, and direct current power supply from a power source 106 to a load device 120 is started. 半導体スイッチ103にHiレベルの電源切換信号112が入力されるとON状態となり、電源106から負荷装置120への直流電源の供給が開始される。 - 特許庁
When the input signal SIN is at e.g. logical 'H', the saturation current of the FET 22 flows to ground GND via the gate and the source of the FET 22 and also flows to a resistor 21. ここで、入力信号S_INが例えば“H”のとき、FET22の飽和電流が該FET22のゲート及びソースを介してグランドGNDに流れるが、この飽和電流は抵抗21にも流れる。 - 特許庁
Two output signals of the sensor 12 are input into a differential ampififying circuit 30, and an output signal is detected by a synchronous detection circuit 32 to be amplified thereafter by a direct current amplifying circuit 34. 角速度センサ12の2つの出力信号を差動増幅回路30に入力し、その出力信号を同期検波回路32で検波した後、直流増幅回路34で増幅する。 - 特許庁