The control part 7 estimates the state of the housing, based on the temperature characteristic of the housing 15, and selects the input value of the supply current supplied to the pressure detecting element, so as to offset the effect of the state of the housing on a measured value of the pressure. 制御部7は、ハウジング15の温度特性に基づいてハウジングの状態を推定し、ハウジングの状態が圧力測定値に及ぼす影響を相殺するように圧力検知素子へ供給される供給電流の入力値を選択する。 - 特許庁
A switching element 3 for power ON/OFF is connected in series between the DC power supply 1 and an input terminal of a voltage converting circuit 2, and this switching element 3 is maintained in OFF in the power OFF condition to cut off leak current from the DC power supply 1. 直流電源1と電圧変換回路2の入力端子間にパワーオン・オフ用スイッチング素子3を直列に接続し、パワーオフ時には、このスイッチング素子3をオフ状態に保ち、直流電源1からのリーク電流を遮断する。 - 特許庁
When there is no difference between the input voltage and the output voltage of the switching element 3 and the value of lamp current is larger than the threshold value, a lamp-protection means 17 turns on a thyristor 18, short-circuits the output of a chopper circuit 2 and protects the discharge lamp 12. ランプ保護手段17はスイッチング素子3の入力電圧と出力電圧に差がなく、しかもランプ電流がしきい値より大きい場合には、サイリスタ18を導通させ、チョッパ回路2の出力を短絡して、放電ランプ12を保護する。 - 特許庁
When the intensity of a light beam is adjusted, a driving pulse current the period of which and ON time of each pulse of which are fixed is input into a semiconductor laser 211, a pulse beam is received by a light-receiving unit 51, and a detection signal is output by the light-receiving unit 51. 光ビームの強度調整の際には、周期および各パルスのON時間が一定である駆動パルス電流が半導体レーザ211に入力され、パルスビームが受光部51にて受光されて検出信号が出力される。 - 特許庁
To perform both the protection of an electric compressor and the prevention of the lowering of a refrigerating capacity when a power voltage varies by controlling the rotational speed variation rate of the electric compressor according to the input current of the electric compressor to a drive control device. 電動圧縮機の駆動制御装置への入力電流に応じて、電動圧縮機の回転数変化速度を制御することにより、電源電圧変動時に電動圧縮機の保護および冷凍能力の低下防止を両立させる。 - 特許庁
To provide such amplifier circuits adopting a configuration of a plural ity of stages having off-leak current interruption transistors (TRs) that input sensitivity is enhanced by noise prevention and a signal amplification characteris tic is improved by suppressing a deviation in a circuit threshold value among the amplifier circuits. オフリーク電流遮断用トランジスタを有する複数段構成の増幅回路において、ノイズの防止による入力感度の向上、及び、各増幅回路間における回路閾値のずれの抑制による信号増幅特性の向上を図る。 - 特許庁
The phase control circuit of DC trigger type measures the time difference between a zero cross point of input voltage and the zero cross point of the current in the closed circuit, and based on the time difference measured, the timing of switching off the drive voltage of the two-way switching element Q1 is determined. DCトリガ方式の位相制御回路は、入力電圧のゼロクロスと閉回路中の電流のゼロクロスとの時間差を計測し、計測された時間差に基づいて双方向スイッチング素子Q1の駆動電圧をオフさせるタイミングを決定する。 - 特許庁
A control section 110 controls the switches 140a to 140d connected in series with the first light sources 120a in response to an received input data signal to produce a multi-value optical signal at a low current equal to that with the case of driving one light source. 制御部110は、第1の光源120aと直列接続されたスイッチ140a〜140fを入力されたデータ信号に応じて制御することにより、多値光信号を光源1個を駆動する場合と同等の低電流で生成する。 - 特許庁
A current table group is configured to store an output voltage value of a cell in each elapsed time of a plurality of elapsed times from the change start time of an input voltage to be applied to the cell for each cell, and stored in a storage device which is accessible by a design support device. 電流テーブル群は、セルへ与える入力電圧の変化開始時からの複数の経過時間の各経過時間でのセルの出力電圧値をセルごとに保持し、設計支援装置がアクセス可能な記憶装置に記憶されている。 - 特許庁
On the other hand, if 'speed priority' mode is selected, all paper sizes, which are common to each printer that belongs to a current selected group, such as 'B5' and 'A4', are displayed in the paper size input pull-down menu MN2 as a menu of choices. 一方、「速度優先」のモードが選択されている場合には、用紙サイズ入力用のプルダウンメニュMN2に、現在選択されているグループに属する各プリンタに共通な用紙サイズである、例えば「B5」、「A4」を選択肢として表示する。 - 特許庁
To prevent voltage input to a circuit chip, which is mounted on a glass substrate of a liquid crystal panel by a COG method, from being changed even when a current allowed to flow into the circuit chip is changed and to prevent the generation of flicker on a picture when a still image is displayed. 液晶パネルのガラス基板上にCOG工法で実装された回路チップに流れる電流が変化しても、回路チップに入力される電圧が変化することがないようにし、静止画を表示させたときの画面チラツキを防止する。 - 特許庁
A pulse density modulating inverter as a power conversion device is caused to exercise control, and the sum of the period of power supply from the inverter to a load and the period of power supply stop takes a value obtained by multiplying the period of the fundamental waves of an input alternating-current power supply by an even number. 電力変換装置としての前記インバータから負荷への給電期間と停止期間の合計周期と、入力交流電源の基本波の周期との間に偶数倍の関係を持たせた制御を該インバータに行わせる。 - 特許庁
On the other hand, the span correcting amount is converted into a current by means of another V/I conversion circuit 12 after the amount is converted into a voltage by means of a D/A conversion circuit 9 for span correction and inputted to the reference input terminal Iref of the conversion circuit 4. 一方、スパン補正量は、スパン補正用D/A変換回路9により電圧に変換された後、V/I変換回路12により電流に変換されてA/D変換回路4の基準入力端子Irefに入力される。 - 特許庁
The voltage variation interference is decreased, by controlling to reduce the power supply to the load such as the fixing heater or other components, when changes, such as increase or decrease in the input current in the image forming apparatus, continues for a preset prescribed time or longer. 画像形成装置の入力電流の増加または減少の変化が予め定められた所定時間以上継続した時に定着ヒータや他の部品などの負荷への通電を下げるように制御し、電圧変動妨害を低減する。 - 特許庁
When a gate voltage is input to a switching element Q2 at the time of preheating, a charge current flows from the gate of the switching element Q2 to a capacitor C4 via a resistor R5, a diode D3, a capacitor C5 and a resistor R6, and the capacitor C4 is charged. 予熱時においてスイッチング素子Q2にゲート電圧が入力されると、スイッチング素子Q2のゲートから抵抗R5、ダイオードD3、コンデンサC5及び抵抗R6を介してコンデンサC4に充電電流が流れ、コンデンサC4が充電される。 - 特許庁
In the driving circuit using the solid-state relay 16, the resistance element 12 arranged on the input side has a positive temperature coefficient whose gradient is gentle, and can reduce a value of a current applied to the light emitting element when a temperature is high. このソリッドステートリレー16を使用した駆動回路において、入力側に配置した抵抗素子12は、ゆるやかな傾きの正の温度係数を有するものであり、高温時に発光素子に流す電流値を少なくすることができる。 - 特許庁
The differential amplifier circuit 20 includes N-channel MOS transistors 23, 24 to which an input signal and a reference signal are inputted, and switches 18-1-3, 18-2-3 select connection points (P1, P2) from which a differential output current should be taken out. 差動増幅回路20は、入力信号と基準信号が入力されるNチャンネルMOSトランジスタ23、24を備え、スイッチ18−1−3、18−2−3により差動出力電流を取り出すべき接続点(P1、P2)を選択する。 - 特許庁
The terminal comprises a current position measuring unit 241, and a manual input unit 213 inputting a mode for navigating a person or a mode for navigating a car wherein map information is displayed on the screen of a display 231 while being varied depending on the mode. 現在位置測定装置241と、人が歩くマンナビ用のモード表示とするかまたは車でのカーナビ用のモード表示とするかの手動入力装置213を有し、モード表示により、地図情報を変えて、表示装置231の画面に表示する。 - 特許庁
When a voltage detection circuit 23 detects corrosion of the contact 14, a timing generation means 24 changes over a corrosion prevention current-carrying part 22 arranged on the same input terminal 17 as that of the voltage detection circuit 23 into a corrosion prevention state. 電圧検出回路23が接点14の腐食を検出すると、タイミング生成手段24が前記電圧検出回路23と同一の入力端子17に設けられる腐食防止電流通電部22を腐食防止状態に切替える。 - 特許庁
The motor includes an inverter circuit 20 for supplying a driving current to each phase of a coil group, and a control circuit 30 for controlling the inverter circuit 20 by a PWM method according to a predetermined input signal to drive a rotor 3 at a predetermined rotating speed. コイル群の各相に駆動電流を供給するインバータ回路20、所定の入力信号に従ってインバータ回路20をPWM方式により制御し、ロータ3を所定の回転速度で駆動する制御回路30を備える。 - 特許庁
By a heat control and temperature monitoring system (HCTMS), a jointing temperature of components is monitored using a temperature sensor (403), and an applied power is increased so that a self heating characteristics is enhanced by a zero input leakage current specific to the component (404). 熱制御&温度監視システム(HCTMS)により、コンポーネントの接合温度は温度センサを用いて監視され(403)、コンポーネントに固有の零入力漏れ電流により自己加熱特性を増強するように、印加電力が増加される(404)。 - 特許庁
To set current attenuation speed to be low and to discharge energy without quenching a superconducting coil at the time of a stop when abnormality such as an input power loss of an excitation means does not exist in the superconducting coil and energy is not necessary to be discharged rapidly. 励磁手段の入力電源喪失など、超電導コイルに異常がなく、急速に放電する必要のない停止時には、電流減衰速度を低速に設定し、超電導コイルをクエンチすることなく、エネルギーを放電することにある。 - 特許庁
When the input terminal is switched to an Lo level, a P_D2 is turned on, and since a high voltage is still applied to the output terminal of the output element N_O5, the N1 is also turned on, and the current driving capability of the output element No5 is turned on though in a low state. 入力端子をLoレベルに切替えると、P_D2はオン、N_O5の出力端子には未だ高電圧が印加されているので、N1もオンの状態となり、N_O5の電流駆動能力は低い状態ではあるが、オン状態となる。 - 特許庁
A control unit (5) controls each of the switching elements (Srp, ..., Stn) so that line voltages between a basis phase and the other phases are output to the two DC link sections (L1, L2), in time division, assuming one phase of the input three-phase alternate current to be the basis phase. また、制御部(5)は、入力三相交流の1つの相を基準相として、基準相と他のそれぞれの相との線間電圧が時分割で2つの直流リンク部(L1,L2)に出力されるように、それぞれのスイッチング素子(Srp,…,Stn)を制御する。 - 特許庁
In addition to that, this invention makes the output voltage of the generator 1 variable by adjusting the field current, and uses an induction motor 2 for a motor to obtain the same motion as by an inverter since the torque speed is variable following the input voltage. さらに、発電機1の出力電圧を界磁電流を調整することにより可変とすることと、電動機として誘導電動機2を用い、入力電圧によりトルク速度が可変出来ることによりインバータと同等の動作を行わせる。 - 特許庁
The rectifying control logic 32 synthesizes the input signals, generates a gate drive signal that contains a modulation pulse and has a prescribed energizing angle for outputting to an inverter 12 via a gate drive part 34, and controls the PWM current of the motor 10. 整流制御ロジック32はこれらの入力信号をシンセサイズして変調パルスを含んだ所定の通電角度のゲート駆動信号を発生しゲート駆動部34を介してインバータ12に出力しモータ10のPWM電流制御を行う。 - 特許庁
The non-contact IC card makes the hysteresis width of a comparator 16 vary in accordance with the level of an input signal to the comparator 16, in actuality, in accordance with the output voltage value of a full wave rectifying circuit 12 or a value of current passing through a shunt regulator 15. 非接触式ICカードおいて、コンパレータ16への入力信号のレベルに応じて、実際には全波整流回路12の出力電圧値やシャントレギュレータ15で流れ出る電流値に応じて、コンパレータ16のヒステリシス幅を変動させる。 - 特許庁
Emitter currents are determined at relatively low potentials by a transistor 65; and when the difference of values of currents flowing to transistors 63 and 64 are generated, a current, corresponding to the portion of the change is supplied to the inversion input terminal of an operational amplifier 30. そして、トランジスタ65によって、エミッタ電位は比較的低い電位に確定され、トランジスタ63,64を流れる電流の値の差異が生じた際にその変化分に対応する電流がオペアンプ30の逆相入力端子に供給される。 - 特許庁
Moreover, this detects the current on the side of AC input of a converter and sends it out to a PWM controller thereby controlling the DC voltage of each single phase of inverter unit via the PWM controller. またコンバータの交流入力側の電流を検出してPWMコントローラに送出し、PWMコントローラを介して各単相インバータユニットの直流電圧を一定に制御するよう構成したことにより直流電圧の制御も可能とした。 - 特許庁
An early effect cancelling circuit includes an early voltage detector 22 that has the same connection and the same structure as a driver circuit 21 and is connected in parallel to the driver circuit 21, and detects a current flowing in an input transistor Q9 of the early voltage detector 22. ドライバ回路21と同一接続・同一構成を有し、当該ドライバ回路21と並列接続されるアーリー電圧検出部22を備え、当該アーリー電圧検出部22の入力トランジスタQ9に流れる電流を検出する。 - 特許庁
When the contact sensor 45 does not detect the contact with the bottom of the bag body 22 of the dust collection bag 8, it is determined that the dust collection bag 8 is not sufficiently expanded, and a control part increases the input current to an electric fan 6. 接触センサ45が集塵袋8の袋体22の底部との接触を検知していない場合には、集塵袋8が充分に拡がっていない状態と判断して、制御部が電動送風機6の入力電流を増加させる。 - 特許庁
To provide an electrical apparatus which can operate consumer electrics in a time zone when power rate is low during the time from current time to a prescribed time even when a user does not input a desired end time of the operation for a timer reservation operation so as to improve user convenience. タイマー予約運転でユーザが終了希望運転時刻を入力しなくても、現在時刻から所定時間までの時刻において電力料金の安い時間帯に家電機器を運転することができ、ユーザの利便性を向上させる。 - 特許庁
The latch circuit 50 is kept in a concucted condition by a current flowing in the input circuit 12 to bring a low impedance condition, and the MOSFET transistor 32 is maintained thereby in an OFF-condition to bring the starter 10 into an unoperated condition after the initial pulse. 入力回路12を流れる電流によって、ラッチ回路50を導通状態に維持して、低インピーダンス状態にし、これによりMOSFETトランジスタ32をオフ状態に維持し、スタータ10を最初のパルス62の後は不動作状態にする。 - 特許庁
As the completion of setting the bias current of the image forming apparatus is detected based on the light quantity input through the integrating circuit 95, the next operation can be immediately started, thereby reducing the FCOT (First Copy Output Time). 積分回路95を介して入力された光量に基づいて、画像形成装置のバイアス電流の設定完了を検知することにより、速やかに次の処理を開始することが可能となり、FCOT(First Copy Output Time)の短縮を果たすことが可能となる。 - 特許庁
When an FET 13 is put in an ON state, constant currents I2 are supplied from a constant current source 2 to a resistance element 5 according to an input signal VIN, and currents running through the gate of an FET 13 are determined by an output side mirror pair 19. FET13をON状態とする場合、入力信号VINに応じて抵抗素子5に定電流源2による定電流I2を供給し、出力側ミラー対19によりFET13のゲートを介して流れる電流を決定する。 - 特許庁
A recalculation part 30 retrieves measurement data relevant to date data from the pertinent date data in a data storage part 21 to the current date data through a storage data management part 25 based on the input date data and a recalculation instruction. 再演算部30は、入力された日時データ及び再演算指令に基づいて、データ保存部21内の該当する日時データから現在の日時データまでの日時データに関連する計測データを保存データ管理部25を介して検索する。 - 特許庁
To provide the parallel operation controller of power sources which is provided with an outer control voltage input terminal capable of controlling an output voltage for preventing the over current output of each power source when operating plural power sources to be singularly used in parallel. 出力電圧を制御可能な外部制御電圧入力端子を備え、単体で使用される電源を複数台並列運転する場合、各電源における過電流出力を防止する電源の並列運転制御装置を提供する。 - 特許庁
To provide a multi-phase power factor improved converter, capable of forming current running through respective converting parts into a sine wave by connecting converting parts between the phases of multi-phase AC input, and restraining the degradation of fluctuation efficiency due to the fluctuations in inter-phase voltage. 多相交流入力の相間に変換部を接続し、各変換部を流れる電流を正弦波状にすることができるとともに、相間電圧の変動による変換効率の低下が抑制できる多相力率改善形コンバータを得る。 - 特許庁
If the terminals 13, 14, 15 of respective customs brokers and a maritime company input the logistics information including a current location , the quantity and handling expenses of the commodity, the server 11 modifies the logistics information on a warehousing due date and an importer's cost price of offshore inventory. 各乙仲及び船会社の端末13、14、15が、商品の現在地、数量、及び取扱い費用を含む物流情報を入力すると、サーバ11は、洋上在庫の物流情報、入庫予定日及び輸入者原価を修正する。 - 特許庁
Also, since the time during which current flows is shortened, the channel width of a MOS transistor for constituting the NAND gates or the like is increased by a certain degree, impedance on the input side of an inverter 30 is lowered and thus, the influence of the noise is reduced. また、その電流の時間を短縮できるため、NORゲートなどを構成するMOSトランジスタのチャネル幅をある程度大きくしてインバータ30の入力側のインピーダンスを下げることができ、これによりノイズの影響を低減できる。 - 特許庁
This taxi fare system device acquires data at a current location from a GPS to retrieve a path to the input destination, and acquires congestion information from VICS information to calculate a predicted tax fare by time distance combined use fare system, and presents it to a user. GPSから現在位置のデータを得て、入力された目的地までの経路を検索するとともに、VICS情報から渋滞情報を得て、時間距離併用運賃制による予測タクシー料金を算出して、利用者に提示する。 - 特許庁
A switching power supply apparatus 6 includes a current transformer 12, a switching circuit 13, a rectification circuit 15, a smoothing circuit 16, an input voltage detection circuit 18, a control section 19, an output voltage detection circuit 22, and a PWM signal generation section 30. スイッチング電源装置6は、カレントトランス12と、スイッチング回路13と、整流回路15と、平滑回路16と、入力電圧検出回路18と、制御部19と、出力電圧検出回路22と、PWM信号生成部30とを備えている。 - 特許庁
Since the transistor has extremely low off current, the transistor is turned off after data is input to a node, which is a connection point between the transistor and the capacitor element, and can hold the data for a long time even after the stop of power supply voltage. 当該トランジスタは、オフ電流が極めて低いため、トランジスタと容量素子の接続点であるノードにデータが入力された後、トランジスタがオフ状態となり、電源電圧の供給が停止しても、長期間にわたりデータを保持することができる。 - 特許庁
This is semantically equivalent to >word 2>&1 Here Documents This type of redirection instructs the shell to read input from the current source until a line containing only word (with no trailing blanks) is seen.
これは次のものと同じ意味です:>word 2>&1ヒアドキュメント(Here Documents)この形式のリダイレクトを用いると、シェルは現在のソースから入力を読み込みます。 この読み込みはwordを単独で含む行 (末尾にブランク文字があってはいけません)が現われるまで続きます。 - JM
The drive circuit comprises a 1st circuit 1 connected to an input terminal 4 to extract a base current, a 2nd mirror circuit 2 connected to the 1st circuit 1, a switch S connected to the 2nd mirror circuit 2, and a driver 3 connected to the 2nd mirror circuit 2. 入力端子4に接続されベース電流を取り出す第1回路1と、第1回路1に接続される第2のミラー回路2と、第2のミラー回路2に接続されるスイッチSと、第2のミラー回路2に接続されるドライバ3で構成される。 - 特許庁
To provide a filament lamp capable of making a large current flow even when power input to a filament is increased, while having, at the sealing portion, a metal foil connected with an internal lead which is connected to each filament independently capable of supplying power. 各々のフィラメントに独立に給電可能に連結された内部リードが接続する金属箔を封止部に備えつつも、フィラメントへの電力入力を高めたときでも、大電流を流すことが可能なフィラメントランプを提供すること。 - 特許庁
The temperature characteristics compensation circuit 21, in accordance with an operating temperature of the MOSFET 12, controls a voltage to be supplied to the body and adjusts, based on a relation between a body voltage and a gate voltage, a resistance value of a current flowing between the input terminal and the output terminal. 温度補償回路21は、MOSFET12の動作温度に応じて、ボディに供給する電圧を制御して、ホディ電圧とゲート電圧との関係で入力端子及び出力端子間に流れる電流の抵抗値を調整する。 - 特許庁
To provide a switching control circuit in which a timer is constituted of the counter having a small number of stages and then a desired brownout operation signal is obtained from the timer by generating a clock signal from an alternating current (AC) input signal and using it for the clock signal to a counter. 交流(AC)入力信号からクロック信号を生成してそれをカウンタへのクロック信号に用いて少ない段数のカウンタでタイマーを構成し、該タイマーから所望のブラウンアウト動作信号を得るスイッチング制御回路を提供する。 - 特許庁
When an input switch is operated, a microcomputer 4 acquires the current operation state of the vehicle according to the state transition table X stored in the storage device 3 and transmits the acquired operation state to the management center B through a radio transmission line. 入力スイッチが操作されると、マイコン4は記憶装置3に記憶された状態遷移表Xにしたがって現在の車輌の運行状態を取得し、取得した運行状態を無線伝送路を通じて管理センターBに伝送する。 - 特許庁
A battery voltage of the secondary battery 3 is controlled by a step-up circuit 4 so as to become higher than an AC adaptor voltage on the AC adaptor 2 side, and made to be a DC input voltage via a diode 11 which performs switching so that the current flows from a higher voltage side. ACアダプタ2側のACアダプタ電圧より二次電池3のバッテリ電圧が高くなるように昇圧回路4で電圧を制御し、電圧の高いほうから電流が流れるように切り替えるダイオード11でDC入力電圧とする。 - 特許庁
Copyright (c) 2001 Robert Kiesling. Copyright (c) 2002, 2003 David Merrill. The contents of this document are licensed under the GNU Free Documentation License. Copyright (C) 1999 JM Project All rights reserved.