When the bus-tie circuit breaker 3 is turned 'OFF' and the simultaneous protection relay 14 operates, an input current from the bus-time current transformers 4, 5 is forcibly set to zero with a divided protection relay software process 17. 母線1、2間を連絡するブスタイ回路に設けられた遮断器3の片側に母線保護用のブスタイ変流器4、5を設置し、上記母線を一括保護および分割保護方式により保護する母線保護継電装置において、ブスタイ遮断器3「切」で且つ一括保護リレーが動作14したとき、上記ブスタイ変流器4、5からの入力電流を分割保護リレーソフトウェア処理17によって強制的に零にするようにした。 - 特許庁
To soft-start a pad so that the pad acts on a floor surface with a low torque at the time of operation start, to keep a motor torque and a motor current in a flat stable state in a following real use rotation area, namely, in a high speed area, and to control the input current of a motor and an inverter into low value at the time of motor start and motor lock. 操作開始時にはパッドが低トルクで床面に作用するようにパッドをソフトスタートさせ、その後の実使用回転領域、即ち、高速領域に於いてはモータートルクとモーター電流をフラットな安定状態に維持し、且つ、モーター起動時とモーターロック時には、モーター及びインバーターの入力電流が低い値になるように制御することができるように工夫した床面艶出清掃機用モータ駆動制御装置を提供する。 - 特許庁
The phase comparator 2a has a phase comparison circuit 7 for generating a signal corresponding to the phase difference between a reference signal of a predetermined frequency inputted to an input terminal 1 and a signal based on the oscillation signal, and a charge pump circuit 8 which outputs a charge pump current whose current value changes to the loop filter 3a, on the basis of a signal outputted from the comparison circuit 7. 位相比較器2aは、入力端子1に入力される所定周波数の基準信号と前記発振信号に基づく信号との位相差に応じた信号を生成する位相比較回路7と、位相比較回路7から出力される信号に基づいてチャージポンプ電流をループフィルタ3aに出力し且つ前記チャージポンプ電流の電流値が可変するチャージポンプ回路8とを有する。 - 特許庁
A navigation control circuit 1 detects a current position of an own vehicle on the basis of map data from a map data input unit 3 and a detection signal from a position detector 2 so as to determine whether or not the own vehicle is now travelling in the passing lane of the highway (step S1). ナビ制御回路1は、自車両が高速道路の追い越し車線を走行中であるか否かを判定するために、地図データ入力器3からの地図データ及び位置検出器2からの検出信号に基づいて自車両の現在位置を検出する(S1)。 - 特許庁
In the AD converter 9, the output signal Vout is sampled twice in a transition response period of the output signal Vout with respect to the input current Iin, the instantaneous values of the output signal Vout in respective timings serve respectively as the first and second measured value. AD変換器9では、入力電流Iinに対する出力信号Voutの過渡応答期間に2度出力信号Voutのサンプリングを行い、各サンプリングタイミングでの出力信号Voutの瞬時値をそれぞれ第1および第2の計測値とする。 - 特許庁
When an on-off operation of an air conditioner switch 38, and a start/end of acceleration-cut control change the input value of current to the coil 51, a control computer 37 performs switching control to switch the on-off switch 40 over alternately between the on and off-positions. 制御コンピュータ37は、エアコンスイッチ38のオン操作時及びオフ操作時、加速カット制御の開始時及び終了時のそれぞれにおいて、コイル51に対する入力電流値を変更する際には、オン・オフスイッチ40をオン位置とオフ位置とに交互に切換動作させるスイッチング制御を行なう。 - 特許庁
Detection of the leak current is enabled by adding high impedance loads to the gate electrode of the transistor, the input terminal of the logical gate circuit and the open/close control terminal of the switching circuit and fixing the potential of each of the electrodes/terminals to potential between a power supply voltage and a ground voltage. トランジスタのゲート電極・論理ゲート回路の入力端子・スイッチ回路の開閉制御端子にハイインピーダンス負荷を付加し、それぞれの電極・端子の電位を電源電圧からグランド電圧の間の電位に固定することにより、リーク電流の検出を可能にする。 - 特許庁
With an analog switch 4 being set to off, a current determined by an input resistance Ri connected to an output voltage of the shift means 7 flows across an integral capacitor Ci to drop an output voltage of an operational amplifier 1, which then rises with the switch when turned on. アナログスイッチ4がオフの場合、レベルシフト手段7の出力電圧と接続する入力抵抗Riによって決まる電流が積分コンデンサCiに流れて演算増幅器1の出力電圧が下降し、オンの場合、演算増幅器1の出力電圧が上昇する。 - 特許庁
Further, input protective circuits 17, electrically connected to the internal circuit 10 and the pads 12 for inspection while preventing the inflow of an excessive current from the pads 12 for inspection into the internal circuit 10, are formed in the scribe region Rs and the vicinity of the same. さらに、スクライブ領域Rs及びその近傍部に、内部回路10及び検査用パッド12のそれぞれと電気的に接続されており且つ検査用パッド12から内部回路10に過剰な電流が流れ込むことを防止する入力保護回路17が形成されている。 - 特許庁
The driving method comprises a first step for detecting gradation of a data current based on the display data input from the outside; and a second step for discharging the data lines D1 to D4 up to the discharge level corresponding to the display data on the basis of the detected gradation. そして、その駆動方法は、外部から入力される表示データに従うデータ電流の階調を検出する第1段階と、前記検出された階調によって前記データラインを前記表示データに対応する放電レベルまで放電させる第2段階とを含む。 - 特許庁
A dimming circuit 330 forming a controller 331 receives the input signal VIN with the conduction angle, and converts into a DC signal correlated with the conduction angle, and determines luminance of a LED by controlling current passing through a LED circuit 35 on the basis of the DC signal. 制御器331を構成する調光回路330は、導通角度を有する入力信号VINを受信し、導通角度と相関関係がある直流信号に変換し、その直流信号に基づいてLED回路35を通る電流を制御することによってLEDの輝度を決める。 - 特許庁
A direct current power source 2 and an LED display unit 1 are serially connected between an input terminal 1N of the three terminal regulator 4 and a ground terminal GND, and the variable resistor circuit 5 is connected between an output terminal OUT of the three terminal regulator 4 and the ground terminal GND. 3端子レギュレータ4の入力端子INと接地端子GNDとの間に、直流電源2とLED表示ユニット1とを直列に接続すると共に、この3端子レギュレータ4の出力端子OUTと接地端子GNDとの間に可変抵抗回路5を接続した構成とする。 - 特許庁
Then an input signal from a CCD 58 is analyzed, a deviation of the optical axis of light projected from an AF auxiliary light device 10 from an object is calculated and current supply to the piezoelectric element sheet 20 is controlled so as to move the projection lens 14 on the basis of the calculated result. そして、CCD58からの入力信号を解析し、AF用補助光装置10から投光される光の光軸の被写体に対するずれを算出して、算出結果に基づいて投光レンズ14を移動するように圧電素子シート20への通電を制御する。 - 特許庁
The circuit 4B1 for adjusting the color of an input image employs the frequency of histogram for counting the number of pixels judged to be identical substantially in color comparison with a specified color as a parameter related to the color of a previous frame image inputted before a current frame image. 入力画像の色を調整する本調整回路4B1は、現フレーム画像より前に入力された前フレーム画像における色に関するパラメータとして、たとえば、指定色との色比較で略同一と判断された画素数をカウントするヒストグラムの度数を用いる。 - 特許庁
Since the potential difference appears in an amplified state by using the differential amplifier circuit, when the potential of the input signal exceeds the potential level of the limit voltage, a switching element (such as an NMOS transistor 5 or a PMOS transistor 6) is speedily turned on and the current can flow to the resistor 1. 差動増幅回路を用いることで電位差が増幅して現われるため、入力信号の電位が、リミット電圧の電位レベルを超えると速やかスイッチング素子(NMOSトランジスタ5またはPMOSトランジスタ6)をオンさせて、抵抗1に電流を流すことができる。 - 特許庁
Each of high-pass filters 10 and 15 removing DC offset of a signal received and having a converted frequency has a CR filter, and includes a bootstrap circuit 36 increasing input impedance of the high-pass filter by selectively increasing a current flowing to a resistive element of the CR filter. 受信して周波数変換された信号のDCオフセットを除去するハイパスフィルタ(10,15)は、CRフィルタを有し、CRフィルタの抵抗素子に流れる電流を選択的に増やすことによってハイパスフィルタの入力インピーダンスを大きくするブートストラップ回路(36)を備える。 - 特許庁
Thereby, the voltage between the gate G and drain D of the field-effect transistor Q1 becomes the same AC potential, therefore no current is generated through the stray capacitance, and the input impedance of the field-effect transistor Q1 can be made high in the same way as the case that the feedback capacitor is used. これにより、電界効果トランジスタQ1のゲートGとドレインDとの電位が交流的に同一になり、この間の浮遊容量を通じての電流が生じず、帰還コンデンサを用いていた場合と同様にして、電界効果トランジスタQ1の入力インピーダンスが高められる。 - 特許庁
Each inspection unit includes an inspection contactor for contacting a corresponding battery, and a measurement circuit which is connected to the contactor and generates an analog measurement signal by measuring at least one of an electric current, electric voltage, and temperature based on input from the contactor. 検査部の各々は、対応する電池に接触するための検査用の接触子と、接触子に接続されており該接触子からの入力に基づき電流、電圧、及び温度の少なくとも1つを計測してアナログ計測信号を生成する計測回路と、を含む。 - 特許庁
A slow start judging value smaller than an overcurrent judging value is compared with current flowing through a FET 7 by a comparator 22, and the conduction of a transistor 34 is controlled in accordance with the result of judgment by the comparator 22 to change the circuit time constant of an input signal processing circuit 13. コンパレータ22によって過電流判定値よりも小なる値のスロースタート判定値とFET7を介して流れる電流とを比較し、そのコンパレータ22の判定結果に応じてトランジスタ34を導通制御し入力信号処理回路13の回路時定数を変更する。 - 特許庁
The converter 62 has a predetermined threshold value with respect to the magnitude of the output terminal voltage V_out, and a current having a magnitude depending on a magnitude relation between the magnitude of the output terminal voltage and the predetermined threshold value is supplied to an inverted input terminal of the operational amplifier. 変換部62は、出力端子電圧V_outの大きさに対する所定のしきい値を有しており、そしてその出力端子電圧の大きさと前記所定のしきい値との間の大小関係に依存した大きさの電流を、演算増幅器の反転入力端子に供給する。 - 特許庁
To surely prevent a malfunction in a phase control element due to a phase advance current flowing in a parallel capacitor C1 without increasing a power loss in a power supply with the parallel capacitor C1 connected between AC input terminals applied with a phase-controlled AC voltage. 位相制御された交流電圧を印加される交流入力端子間に並列コンデンサC1を備える電源装置において、電力ロスを殆ど増大させることなく、並列コンデンサC1に流れる進相電流による位相制御素子の誤動作を確実に防止する。 - 特許庁
Power is supplied from a power source 700 on the side of the Pachinko game machine to the side of the card treatment machine to input a direct current rectified by a rectifier on the side of the card treatment machine to the side of the Pachinko game machine, whereby switching circuits 710, 712 are operated. パチンコ遊技機側の電源700からカード処理機側へ電力を供給し、カード処理機側の整流器によって整流された直流電流がパチンコ遊技機側に入力され、その入力された直流電流によって、スイッチ回路710,712が動作する。 - 特許庁
To provide a power converter, assuring compatibility of improvement in power conversion efficiency and reduction of power supply harmonics, by realizing a system for reducing harmonics included in an AC input current waveform, without having to raise the switching frequency of an AC/DC power converter. 交直電力変換装置のスイッチング周波数を高めることなく交流入力電流波形に含まれる高調波成分を低減することができる方式を実現し、電力変換効率向上と電源高調波低減の両立が可能な電力変換装置を提供する。 - 特許庁
And since the frequency multiplier 10 is the current exciting frequency multiplier, the first and second resonance circuits 12, 13 are constituted of an LC serial resonance circuit and its first and second resonance circuits 12, 13 are serially connected between the input terminal 11 and the output terminal 16. そして、電流励振型の周波数逓倍器であるため、第1及び第2の共振回路12,13がLC直列共振回路からなり、その第1及び第2の共振回路12,13が入力端子11と出力端子16との間に直列接続される。 - 特許庁
To provide a flying capacitor type cell voltage detection apparatus capable of improving reliability by preventing a short-circuit current by a simple circuit constitution which occurs when an input-side sampling switch and an output-side sampling switch, which are not normally simultaneously on, are simultaneously on. 通常は同時にオンしない入力側サンプリングスイッチ、出力側サンプリングスイッチがともにオンすることで発生する短絡電流を簡素な回路構成で防止し、信頼性を向上することができるフライングキャパシタ式電圧検出装置を提供することを目的とする。 - 特許庁
The adder 14 adds the horizontal parabola signal HP1 given by the parabola modulation circuit 12 and the pulse signals P1a, P2a given by the pulse modulation circuit 13 and gives an output signal AD indicating the addition result to one input terminal of a correction current output amplifier 7. 加算器14は、パラボラ変調回路12により与えられた水平パラボラ信号HP1およびパルス変調回路13により与えられたパルス信号P1a,P2aを加算し、加算結果を示す出力信号ADを補正電流出力アンプ7の一方の入力端子に与える。 - 特許庁
Therefore, silicon oxide is used, in place of a bulk of silicon dioxide, which is usually used as the material for the formation of a gate dielectric layer, and a semiconductor device capable of reducing leakage current is provided, while an input FET capacitance is made to increase. よって、ゲート誘電体層形成の材料として従来使用されていた二酸化シリコン製バルクの代替材料として酸化シリコンを用いることにより、入力FETキャパシタンスを増加させながら、リーク電流を減らすことを可能とする半導体デバイスを提供することを特徴とする。 - 特許庁
The gate-off voltage generator increases the gate-off voltage applied to the switching element to a voltage, obtained by adding an offset voltage having a specified level to increase the amount of a current flowing between the output terminal and the input terminal of the switching element. 前記ゲートオフ電圧生成部は、駆動電源が遮断される時、前記スイッチング素子に印加される前記ゲートオフ電圧を所定の大きさのオフセット電圧が加えられた電圧に高くし、スイッチング素子の出力端子と入力端子との間に流れる電流量を増加させる。 - 特許庁
The frequency converter is provided with a local oscillator 11 for generating a local signal having signal amplitude proportional to the temperature and a mixer circuit 12 which operates by bias current proportional to the temperature, multiplies an input signal by the local signal and obtains an output signal whose frequency is converted. 周波数変換器は、温度に比例する信号振幅を持つローカル信号を発生するローカル発振器11と、温度に比例するバイアス電流により動作し、入力信号とローカル信号との乗算を行って周波数変換された出力信号を得るミキサ回路12とを有する。 - 特許庁
The buffer BUF is configured so as to switch, corresponding to the control signals, an enable state wherein the differential signal corresponding to the differential signal inputted to the differential input terminal Di is outputted and a disable state wherein current consumption practically becomes zero and the differential output terminal becomes high impedance. バッファBUFは、差動入力端子Diに入力される差動信号に応じた差動信号を出力するイネーブル状態と、消費電流が実質的にゼロとなり、その差動出力端子がハイインピーダンスとなるディスエーブル状態と、が制御信号に応じて切りかえ可能に構成される。 - 特許庁
The current mode switching regulator 100 includes a higher-order transistor QH and a lower-order transistor QL, a switching output circuit 180 that generates output voltage Vout1 in proportion to input voltage Vin1, and an output terminal 190 for outputting the output voltage Vout1. 電流モード型スイッチングレギュレータ100は、上位トランジスタQH及び下位トランジスタQLと、入力電圧Vin1に比例した出力電圧Vout1を生成するスイッチング出力回路180と、出力電圧Vout1を出力する出力端子190を備える。 - 特許庁
To provide a lightning arrester that stably supplies a predetermined voltage to a protected circuit-side terminal without incurring trouble due to an induced lightning surge by suppressing magnetic saturation of cores with simpler constitution and effectively reducing an impulse current flowing in from an input-side terminal. より簡素な構成で、コアの磁気飽和を抑制して、入力側端子から侵入するインパルス電流を効果的に低減し、誘導雷サージによる障害を生じることなく被保護回路側端子へ所定の電圧を安定して供給できる避雷器を提供することを目的とする。 - 特許庁
The pulse width modulation circuit 1 includes a current bypass circuit 4 for bypassing charging voltages J1, J2 by supplying clamp voltages Vk1, Vk2 to the input terminals of inverters INV1, INV2 when charging voltages Vc1, Vc2 of the capacitors C1, C2 increase to threshold voltage Vth of the inverters INV1, INV2. パルス幅変調回路1はコンデンサC1,C2の各充電電圧Vc1,Vc2がインバータINV1,INV2のスレシホールド電圧Vthに上昇すると、クランプ電圧Vk1,Vk2をインバータINV1,INV2の入力端に供給して充電電流J1,J2をバイパスさせる電流バイパス回路4を備える。 - 特許庁
A soft-stop overvoltage protection circuit 90, into which a soft-stop overvoltage detection voltage Vfb proportional to a direct current output voltage is input, reduces the output of a multiplier 24 in accordance with the soft-stop overvoltage detection voltage Vfb when the soft-stop overvoltage detection voltage Vfb exceeds a first threshold value. ソフト過電圧保護回路90は、直流出力電圧に比例するソフト過電圧検出電圧Vfbが入力され、ソフト過電圧検出電圧Vfbが第1の閾値を超えたときソフト過電圧検出電圧Vfbに応じて乗算器24の出力を低下させる。 - 特許庁
To provide a current detecting circuit capable of performing integration by lowering the accuracy of a voltage dividing ratio required for a voltage dividing resistor that converts an input voltage to an amplifying circuit into a positive value corresponding to a negative value even if a voltage across a sense resistor deflects to the negative value. センス抵抗の両端電圧が負の値に振れた場合でも増幅回路への入力電圧をその負の値に対応する正の値に変換する分圧抵抗に求められる分圧比の精度を下げることができ、集積化の実現を可能とした電流検出回路を提供する。 - 特許庁
By generating the pulse patterns of a second inverter 15 with correcting reference waves, obtained by dividing sine-wave reference waveforms in a control circuit by a second inverter input voltage waveforms and carrier waves, a high-speed and high-precision output current feedback circuit is made unnecessary in phase response and transfer characteristics. 制御回路内の正弦波基準波形を第2インバータ入力電圧波形で除算して得た補正基準波と、搬送波とで第2インバータ15のパルスパターンを生成することにより、位相特性と増幅特性において高速且つ高精度の出力電流フィードバック回路を不要とする - 特許庁
To obtain a condenser microphone which has a maximum output level and a maximum allowable input sound pressure level raised with any supply voltage by automatically changing a bias of a current amplifier circuit in emitter-follower connection immediately after an impedance converter in accordance with switching of a phantom supply voltage. ファントム電源電圧の切り換えに応じてインピーダンス変換器の直後にあるエミッターフォロワー接続による電流増幅回路のバイアスが自動的に変化して、どの電源電圧であっても、最大出力レベルと最大許容入力音圧レベルが高くなるコンデンサーマイクロホンを得る。 - 特許庁
For measurement by the laser beam for the measurement, the laser beam for the measurement oscillated by an injection current modulated by sine waves is used, electric signals photoelectrically converted in a light receiver are input to a lock-in amplifier, and secondary differentiation processing is performed with the sine waves as reference signals. 測定用レーザ光による測定が、正弦波で変調された注入電流により発振された測定用レーザ光を用い、受光器で光電変換された電気信号をロックインアンプに入力し、前記正弦波を参照信号として二次微分処理を行うものである。 - 特許庁
Since the nonuniformity of the operating state of the amplifying element 4 is detected and the abnormal amplifying element 4 is specified from the plurality of the amplifying elements 4, the aptitude range of the bias current information is made variable according to the input level information 8 irrespective of the number of the composite. 増幅素子4の動作状態の不均一性を検出し、複数の増幅素子4の中から異常な増幅素子4を特定するものであるため、合成数にとらわれることはなく、バイアス電流情報の適性範囲を入力レベル情報8に応じて可変にしている。 - 特許庁
A retrieval object position decision unit 303 sends an active signal to a line 114 when the current picture number of the input image is the same as the picture number in the retrieval object position information buffer 306, but sends an inactive signal to the line 114 when not. 検索対象位置判定器303は、入力画像の現在のピクチャ番号が検索対象位置情報バッファ306のピクチャ番号と等しい場合には線路114にアクティブ信号を送る一方、等しくない場合には線路114にインアクティブ信号を送る。 - 特許庁
To provide a step-up and step-down chopper type DC/DC converter circuit capable of preventing erroneous operation at stepping up or stepping down, obtaining stable operation by preventing excessive internal current, and meeting input voltage of wide range with one coil. 本発明の課題は、昇降圧時における誤動作を防止しすると共に、余分な内部電流を防止することで安定動作を得ることができ、一つのコイルで広範囲な入力電圧に対応した昇降圧チョッパ方式DC−DCコンバータ回路を提供することである。 - 特許庁
The preamplifier circuit provided with an amplifier 2 and a feedback resistor 3 and converting a current signal into a voltage signal, is provided with a control circuit 4 that changes an open loop gain simultaneously with a resistance of a feedback resistor 3 in response to a level of an input signal as its control. 増幅器2と帰還抵抗3とを備え、電流信号を電圧信号に変換する前置増幅回路において、入力信号のレベルに応じて増幅器2のオープンループ利得および帰還抵抗3を同時に変化させる制御を行う制御回路4を備えている。 - 特許庁
Current/voltage information signals of a system input via an auxiliary transformer are converted into digital information signals by analog-digital converters AD1, AD2 via analog filters af1, af2 and then inputted into central processing units CPU1, CPU2 via photocouplers PC1, PC2 for operation. 補助変成器を介して入力された系統の電流電圧情報信号はアナログフィルタaf1,af2を経てアナログ・ディジタルコンバータAD1,AD2でディジタル情報信号に変換され、フォトカプラPC1,PC2を介して中央演算装置CPU1,CPU2に入力され演算される。 - 特許庁
A buffer member 18b absorbing the minor torque fluctuation produced in the pilot clutch mechanism 10e caused by the minor fluctuation in the input current to the pilot clutch mechanism 10e is disposed between the pilot clutch mechanism 10e and an outside rotating member 10a constituting the driving force transmission device. 駆動力伝達装置を構成するパイロットクラッチ機構10eと外側回転部材10aとの間に、パイロットクラッチ機構10eへの入力電流の微小な変動に起因してパイロットクラッチ機構10eに生じる微小なトルク変動を吸収する緩衝部材18bを配設した。 - 特許庁
A map information arithmetic processing part 3 reads map data corresponding to a current position or an optional position detected by a vehicle position detection part 1 from a map data storage part 4, automatically controls respective display elements on the basis of the number set by the input part 2 and prepares deformed map data. 地図情報演算処理部3は車両位置検出部1によって検出された現在地又は任意の位置に対応する地図データを地図データ記憶部4から読み出し、入力部2で設定された個数に基づいて各表示要素を自動的に制御し、デフォルメ地図データを作成する。 - 特許庁
The direct current characteristic measuring circuit 17 outputs an integrated waveform as to the input waveform, and a CPU 11 inputs the integrated waveform to find a difference between voltage values of the integrated waveforms in the first and second waveforms. 直流特性測定回路17は入力波形に対する積分波形を出力し、CPU11が当該積分波形を入力することによって第1の波形と第2の波形の積分波形の電圧値の差を求め、2つの波形の実際の遅延時間を算出する。 - 特許庁
A noise detection circuit 6 is provided with a comparator with hysteresis, voltage-converts an input spark noise-superposed current, compares it by a comparator (operational amplifier OP1), and outputs, to a thyristor 5, a low signal when it is higher than a reference voltage, and a high signal when it is lower than a voltage hysteresis line. ノイズ検出回路6は、ヒステリシス付きコンパレータを備え、入力されたスパークノイズ重畳の電流を電圧変換して、コンパレータ(オペアンプOP1)で比較して、リファレンス電圧よりも高ければLow信号を、電圧ヒステリシスラインよりも低ければHi信号をサイリスタ5に出力する。 - 特許庁
To provide a vertical upward welding method which is excellent in wear resistance of a slidable copper backing surface in contact with a steel plate and capable of performing the welding for a long time even when performing the vertical upward welding under the welding conditions of the large heat input, the high current and the high speed of a thick steel plate. 厚鋼板の大入熱溶接や高電流で高速度の溶接条件での立向上進溶接をする場合においても、鋼板と接する摺動銅当金面の耐摩耗性が優れ、長時間溶接が可能な立向上進溶接方法を提供する。 - 特許庁
A DC power supply source having a power storage system with a capacity to process the current flowing into or out of the inverter is inserted in series to the ground side of the input of the inverter and the output voltage thereof is continuously controlled from zero to be added to the trolley voltage, which is then applied to the inverter. インバータの入力の接地側に、インバータに流入もしくは流出する電流を処理可能な容量の蓄電装置を有する直流電圧源を直列に挿入し、この出力電圧をゼロから連続的に制御して架線電圧に加算してインバータに印加する。 - 特許庁
To interrupt a through current in a shorter time than the case in a conventional semiconductor device in the case where a potential higher than a power potential on the side of a high potential in a semiconductor device is applied to elements in this semiconductor device comprising an interface circuit for conducting the input/output of a signal between the inerface circuit and other circuit. 他の回路との間で信号の入出力を行うインターフェース回路を含む半導体装置において、この半導体装置の高電位側の電源電位よりも高い電位が端子に印加された場合に、従来よりも短時間で貫通電流を遮断する。 - 特許庁