In this traffic system, right turn information related to a right turn is provided to the on-vehicle machine 6 of a vehicle C in the intersection controlled by the right turn sensing about a right turn arrow of a traffic light device 2Aa according to a vehicle sensing signal from a vehicle sensor 13 installed in a right turn lane. 右折専用車線に設置された車両感知器3からの車両感知信号に応じて、信号灯器2Aaの右折矢について右折感応制御を実施する交差点において、前記右折矢に関する右折表示情報を車両Cの車載機6に提供する。 - 特許庁
Then, if receiving the weighting information including a weighted value based on transit time when the vehicle actually turns right or left at the intersection, the controller 10 re-searches a route in consideration of the received weighting information and starts route guidance (S33-S35). そして、センター側装置310から、実際に車両が交差点を右折又は左折したときの通過時間に基づいた重み値を含む重み付け情報を、受信すると、受信した重み付け情報を考慮して経路を再探索して、経路案内を開始する(S33〜S35)。 - 特許庁
A component-mounting face of a printed circuit board 1 is divided vertically and horizontally in grid at even intervals, the center of each chip component 5 is matched to the intersection of the parting line, and a width of the land section 3 is set to the width (a) or smaller of the chip component 5. プリント基板1の部品実装面を縦横に等ピッチ間隔で格子状に分割し、これら縦横の分割線の交点に各チップ部品5の中心を一致させて配置すると共に、ランド部3の幅寸法をチップ部品5の幅寸法a以下に設定した。 - 特許庁
When the current location of the user himself is searched, first the image group GG corresponding to the intersection, or the like, stored in the past is retrieved, and then the past locus to his own current position is followed, while the image groups GG corresponding to the other intersections, or the like, indicated by the pointer 12 are called. 自身の現在位置を探索する場合、過去に記憶している交差点等に対応する画像グループGGを先ず検索し、その後はポインタ12により示される他の交差点等に対応する画像グループGGを呼出ながら、自身の現在位置までの過去の軌跡を辿る。 - 特許庁
After the distance between the vehicle and the obstacle necessary for lateral traveling is secured, longitudinal following is set, and the intersection of the minimum turning radius of the following vehicle and a straight line drawn from the center of a preceding vehicle with the vector of the following vehicle is set as a target point to the inter-vehicle distance of the longitudinal following. 横移動に必要な障害物間の距離を確保した後、処理を縦追従に切り替え、縦追従の車間距離に追従車両の最小旋回半径と追従車両のベクトルで先行車中心から引いた直線の交点を目標点として設定する。 - 特許庁
A cutting face 14 of each of the bits 13A, 13B forms an acute angle α to an orthogonal line P to a straight line Q extending forward in the rotating direction of the pipe body 11 from an intersection T of the cutting face 14 and the straight line Q intersecting an axis Z of the pipe body 11, on the outside of the orthogonal line P. 各ビット13A,13Bの削面14は、管体11の軸心Zに交差する直線Qと削面14との交点Tから管体11の回転方向前方に延びる直線Qとの直交線Pに対し、この直交線Pの外側において鋭角αをなしている。 - 特許庁
This OLED, constituted of at least one layer of organic layer pinched by a positive electrode 11 and a negative electrode 16 on a translucent substrate, and at a luminous point Py which, is the intersection point of the positive electrode 11 and the negative electrode 16, a defective part Z is installed which will not present light emission. 透光性の基板上に陽極11と陰極16とで挟んだ少なくとも1層以上の有機層で構成される有機電界発光素子であって、陽極11と陰極16との交差個所である発光個所Pyに発光を呈しない欠損部分Zを設ける。 - 特許庁
There is provided the holding material for the catalytic converter which is for the catalyst carrier having an ellipse cross section, and which has a first portion in contact with a region of the catalyst carrier, corresponding to 40 to 95% of a major axis centering on an intersection of an ellipse and a minor axis in the catalyst carrier, larger than a second portion in contact with any other region of the catalyst carrier. 断面が楕円の触媒担体用であって、触媒担体の、楕円と短径との交点を中心にして長径の40〜95%に相当する領域と接する第1部分が、他の領域と接する第2部分よりも坪量が大きい触媒コンバーター用保持材。 - 特許庁
The focus offset dependence at one point of the spherical aberration correction value is measured with respect to the evaluation indexes 1, 2, approximated straight lines L1, L2 are calculated from the result and the stored information, and the optimum values of the spherical aberration correction value and the focus offset are detected from an intersection point thereof. そして球面収差補正値の一点におけるフォーカスオフセット依存性を評価指標1、2に関して測定し、この結果と記憶している情報から近似直線L1、L2を算出し、その交点から球面収差補正値及びフォーカスオフセットの最適値を検出する。 - 特許庁
Geometrical changes produce a blade having a plurality of slanted surfaces at the working end of the blade at one obtuse angle in the range of 93 degrees to 97 degrees, and the other working end at an acute angle that forms an offset point between the cleaning edge and the intersection of the two angles. 幾何学的変化により、93度から97度までの範囲内の鈍角にあるブレードの作業端において、およびクリーニングエッジとこれらの2つの角の交点との間にオフセット点を形成する鋭角のもう1つの作業端において、複数の傾斜面を有するブレードが生成される。 - 特許庁
The second delay addition part calculates the reference propagation time to the reference point 17 from each of the intersections 23, the focus propagation time to each reception focus from each intersection 23 to compute the difference from the reference propagation time for each determined focus propagation time, thereby carrying out the delay addition processing. 第2の遅延加算部は、各交点23から基準点17までの基準伝搬時間と、各交点23から各受信焦点までの焦点伝搬時間とを算出し、各焦点伝搬時間について基準伝搬時間との差を算出して遅延加算処理を行う。 - 特許庁
This electrophoretic device 1 is provided with an introduction flow passage 11 for making the sample flow from one end side toward the other end side, and the analytical flow passage 10 crossed with the introduction flow passage 11, and for separating the sample in an intersection part 8 from an introduction flow passage 11 side to be electrophoresed. 試料を一端側から他端側へ向けて流動させる導入流路11と、導入流路11に交差して、この交差部8の試料を導入流路11側から分離して電気泳動させる分析流路10と、を備えた電気泳動装置1である。 - 特許庁
The liquid crystal display device comprises a liquid crystal display matrix 300 in which a liquid crystal display pixel is formed in correspondence with the intersection of a scan line L and a data line D, a scan line driving circuit 100 for driving a scan line D, and a data line driving circuit 200 for driving a data line D. 液晶表示装置は、走査線Lとデータ線Dの交点に対応して液晶表示画素が形成されている液晶表示マトリックス300と、走査線Dを駆動する走査線駆動回路100と、データ線Dを駆動するデータ線駆動回路200とを有する。 - 特許庁
A detected speed and a specified vehicle location are recorded to be made correspond to each other in a traveling history recording part 50, and the confirmation location where the driver should confirm the surroundings when entering the intersection is decided based on information recorded in the traveling history recording part 50. 走行履歴記録部50には、検出された車速と、特定された車両位置とが対応づけて記録されており、この走行履歴記録部50に記録された情報に基づいて、交差点への進入時にドライバが周囲確認すべき確認位置が判定される。 - 特許庁
To provide a gusset bag which prevents load or stress from being concentrated on an intersection of an inclined welded portion of a gusset and a welded portion provided on one side of the bag if a wide article is put in the gusset bag and the widths of the article and the gusset do not match. この発明はガゼット袋に幅のある品物を入れた時、この品物と前記ガゼット部の幅が一致しないときでも、前記のガゼット部の傾斜溶着部と袋の一辺に設けた溶着部との交点に荷重乃至応力の集中しない袋を提供する。 - 特許庁
The electrical measuring instrument is provided with an inclined first surface 1a and an inclined second surface 1b; an upper surface 2 provided for an intersection part of the first surface 1a and the second surface 1b; and meters 4a and 4b each provided for the first surface 1a and the second surface 1b. それぞれ傾斜している第1の面1aと第2の面1bと、第1の面1aと第2の面1bの交差部分に設けられた上面2と、第1の面1a及び第2の面1bにそれぞれ設けられたメータ4a,4bとを備える電気計測器である。 - 特許庁
An anchor board 7 provided with the anchor material 8 in one side and increasing its thickness into a protrusion state in the board thickness direction is manufactured separately with its form matched with the form of the board joint intersection of the aright material and the anchor board 7 is integrally welded in executing the airtight material so that the efficiency of the execution is enhanced. 又、一方側にアンカー材8を備えて板厚方向に隆起状に増厚するアンカー板7を、気密材の板継ぎ交点の形態に合わせて別途に製作しておき、気密材の施工時にアンカー板7を一体に溶接することで、施工の効率化を図っている。 - 特許庁
In this convergence electron diffraction method for acquiring a disc-shaped diffraction figure, by making electron beams converge and irradiate to a sample, all of six (a, b, c, α, β, γ) lattice constants of a crystal can be measured from the microregion smaller than 10 nm, from the distance between the intersection points of HOLZ line appearing in a transmission disc. 試料に電子線を収束させて照射し、ディスク状の回折図形を得る収束電子回折法において、透過ディスク内に現れたHOLZラインの交点間の距離から、結晶の格子定数6つ(a、b、c、α、β、γ)全てを10nm以下の微小領域から測定することを可能にする。 - 特許庁
A cylinder bore is formed in a cylinder block so that the upper end side inclines to the left side with respect to a vertical line LN1 in a state of passing the center line CL of the cylinder bore through an intersection between a mating face SL and the vertical line LN1 passing through the center O of a crankshaft 21. シリンダボアの中心線CLが、当該合わせ面SLとクランクシャフト21の中心Oを通る垂直線LN1との交点を通過した状態で前記垂直線LN1に対して上端側が左側に傾斜するように前記シリンダボアを前記シリンダブロックに形成している。 - 特許庁
A grid created by a grid data creation part 7a is formed on the reference face, and a triangular face inside/outside determination part 7c determines whether an intersection between a straight line passing through the center of each grid on the reference face and is parallel to the Z axis, and the triangular face exists inside the triangular face. 格子データ生成部7aで生成した格子を基準面に形成し、基準面の各格子の中心を通りZ軸に平行な直線と3角形フェースの交点が3角形フェース内部に存在するかどうかを3角形フェース内外判定部7cで判定する。 - 特許庁
The vias of the multiple via cell section are on a grid line in an X direction and a grid line in a Y direction both of which are defined with a minimum wiring pitch, and all or part of the vias of the first multiple via cell section deviate from an intersection of the grid line in the X direction and the grid line in the Y direction. 多重ビアセル部のビアは最小配線ピッチで規定されるX方向のグリッド線とY方向のグリッド線に載り、前記第1の多重ビアセル部の全部又は一部のビアは前記X方向のグリッド線とY方向のグリッド線の交点からずれている。 - 特許庁
A vehicle number recognition device is attached to a traffic signal at a road intersection to recognize a passing vehicle, and additional data such as the signal state, the date of passage, and the place of the intersections is added to recognized vehicle information, and they are temporarily stored in a site data storage device incorporated in a signal control board. 車輌番号認識装置を道路交差点の交通信号機に取り付け、通過車輌を認識し、認識した車輌情報に信号状態、通過日時、交差点設置場所等の付加データを添えて信号機制御盤に内蔵した現場データ蓄積装置に一時的に蓄積する。 - 特許庁
The optical fiber cutting means 10 includes a first blade 11 which advances in cutting direction to cut the optical fiber 20, and a support member provided oppositely to the cutting direction for supporting the optical fiber 20 at its tip formed by the lines of intersection of two planes which intersect at an acute angle. 切断の向きに進行して光ファイバ20を切断する第1の刃11と、前記切断の向きに対向して設けられ、鋭角に交わる二つの面の交線から形成される先端部で前記光ファイバ20を支持する支持部材とを備えた光ファイバ切断手段10。 - 特許庁
In response to a guidance route set by the route search of a guidance route setting means 3, a signal pertinent to a direction where the vehicle passes the intersection is selected based on the received lighting display information, and a plurality of signal information corresponding to the direction is provided to a driver. 誘導経路設定手段3の経路探索によって設定された誘導経路に応じて、受信した点灯表示情報に基いて、車両が交差点を通過する方向に該当する信号機を選択し、この方向に応じた複数の信号機情報が運転者に提供される。 - 特許庁
A chip member 20 is provided on the intersection part of the two piezoelectric elements 10A, 10B arranged to make a prescribed angle (for instance, 90 degrees), and the chip member 20 is pressurized in contact on a rotor 40 by a pressurization member 45 together with a base member 30 holding the piezoelectric elements 10A, 10B. 所定角度(例えば90度)をなすように配置された2つの圧電素子10A、10Bの交差部分にチップ部材20を設け、圧電素子10A,10Bを保持するベース部材30と共に、加圧部材45によりチップ部材20をロータ40に加圧接触させる。 - 特許庁
A vehicle control unit 12d controls various devices 50 and an output device 30 in such a manner that the degree of danger of the determined vehicle is reduced (for example, outputting a pre-announcement informing the vehicle of the interest is under the access to the intersection to the driver from a loudspeaker 31, if the danger level is 2). 車両制御部12dは、判定された車両の危険性を減ずるように各種機器50や出力装置30を制御する(例えば、危険レベルが2であれば、相手の車が交差点に進入している旨の予報をスピーカ31から運転手に出力する)。 - 特許庁
The demand rate ρ of each incoming route having a passage right under specific indication among incoming routes at a self-intersection is calculated, and (1) the indication time T is determined according to a relationship between the predetermined demand rate ρ and the indication time T based on any of the calculated demand rates ρ. (1)現示時間Tは、自交差点の流入路のうち、特定現示で通行権が有る各流入路の需要率ρを算出し、算出した各需要率ρの何れかをもとに、予め定められた需要率ρと現示時間Tとの関係に従って決定する。 - 特許庁
When it is determined that a support starting point, immediately before the intersection is reached (S20: YES), provided information is received from a road side machine installed on the road and other vehicles around own vehicle; and on the basis of that, the driving support image (initial field of view) is displayed (S50). ここで、交差点手前の支援開始ポイントに到達したと判定した場合(S20:YES)、路上に設置されている路側機及び自車両周辺の他車両から提供情報を受信し、これに基づいて運転支援画像(初期視界)の表示を開始する(S50)。 - 特許庁
To provide a safety drive support system for highly effectively support safety drive at any intersection irrespective of whether safety drive support is adopted, while preventing a driver from feeling any overconfidence or distrust in the safety drive support system. 安全運転支援が実施される交差点と実施されない交差点が混在している場合であっても、ドライバが安全運転支援システムに過信や不信を抱かないように、実効性の高い安全運転支援を行うことができる安全運転支援システムを提供する。 - 特許庁
To provide an emergency vehicle priority control system for controlling a signal indication of a signal so that an emergency vehicle pass across an intersection preferentially, regardless of the running status of the emergency vehicle, and also to provide a control device and an image processing device constituting the emergency vehicle priority control system. 緊急車両の走行状態に拘わらず、交差点を緊急車両が優先的に通過するように信号機の信号表示を制御する緊急車両優先制御システム並びに該緊急車両優先制御システムを構成する制御装置及び画像処理装置を提供する。 - 特許庁
To provide a joint member which is smaller in size and more excellent in water cutoff performance than before, exerts high adhesion strength to concrete, and brings about enhanced water cutoff function at a joint of a building when arranged at an intersection point between the joints. 従来よりも小型化した目地部材であって従来よりも止水性に優れ且つコンクリートに対する付着強度が高い目地部材であって、目地の交差部分に配設されることで建築物の目地における止水機能を高めることができる目地部材を提供する。 - 特許庁
A torque transmitting ball 7 is installed between a track groove 5 of an outer ring 1 and a track groove 6 of the inner ring 3 and is held by a retainer 8, and a chamfer 12 is formed at the intersection of the inside surface of the inner ring track groove 6 with a spherical outside surface 4 formed on the inner ring 3. 外輪1のトラック溝5と内輪3のトラック溝6間にトルク伝達ボール7を組込み、そのトルク伝達ボール7を保持器8で保持し、前記内輪トラック溝6の内面と内輪3に形成された球形外面4の交差部にチャンファ12を形成する。 - 特許庁
Between the slide rail and each of the sides of two end caps joined to a slide block and a scraper set on the slide rail, the circulation space is designed for joining the intersection type circuit and the separation type circuit into one unit, to form a circulation system wherein two independent circuits exist opposing each other. スライド・レールと、スライド・レールにセットされたスライド・ブロック及びスクレーパに接合された二つのエンドキャップの両側間に、それぞれ交差式循環径路及び分離式循環径路を結合して一体とした循環空間を設計し、二つの独立し、経路が相反する循環システムを構成する。 - 特許庁
When it is judged that the bicycle is approaching the intersection based on the ID data of the RFID tag 300 supplied from the RFID read/write part B220 and the RFID read/write part A210, the display unit 100 warns by displaying notification information constituted of predetermined characters or graphics. 表示器100は、RFIDリードライト部B220およびRFIDリードライト部A210からそれぞれ供給されるRFIDタグ300のIDデータに基づいて自転車が交差点に接近していると判断した場合、所定の文字や図形からなる通知情報を表示して警告する。 - 特許庁
A dividing part divides an axis of the ordinate of a correction light amount curve in steps of setting light amount units A by a dividing line parallel to a main scan direction (step S12) and undergoes block division by a block sectioning line which passes an intersection between the dividing line and the correction light amount curve and is perpendicular to the dividing line (step S13). 分割部は補正光量曲線の縦軸を設定光量単位A刻みで主走査方向と平行な分割線で分割し(ステップS12)、この分割線と補正光量曲線の交点を通り、分割線に垂直なブロック区切り線でブロック分割する(ステップS13)。 - 特許庁
A D/A converting circuit has gate lines 8 and diffusion layers 9 which are arranged in a lattice shape and when an arbitrary MOS transistor Q1 arranged at an intersection of a gate line 8 and a diffusion layer 9 turns on, diffusion layers 9 on the right and left sides of the position of the above MOS transistor Q1 conduct through the MOS transistor Q1. D/A変換回路は、格子状に配置されるゲート線8と拡散層9を有し、ゲート線8と拡散層9の交差位置に配置された任意のMOSトランジスタQ1がオンすると、その場所の左右にある拡散層9がMOSトランジスタQ1を介して導通する。 - 特許庁
To each planar part 21, 23, 26, each inclined plane part 22, 24 and a vertical plane part 25, coloring treatment is applied so that the lightness of each colored layer applied onto each mutually-adjacent plane is different, and the boundary between both colored layers of each adjacent plane agrees with the line of intersection between both planes. 文字盤2を形成する各平面部21、23、26、各斜面部22、24、垂直面部25に対して、互いに隣り合う各面に施された着色層の明度が異なるように着色処理を施し且つ隣り合う各面の両着色層の境界を両面の交線と一致させている。 - 特許庁
In pressurizing and clamping the pin part 3 with the upper and lower arms 9, 11, the center of the pin part 3 is located in an intersection point P of the rotating locus M of the clamping central part of the upper and lower arms and the rotating locus N of the center of the pin part 3 around the journal part 5 of the crankshaft 1. ピン部3を上下各アーム9,11で加圧挟持する際に、ピン部3の中心を、上下各アーム9,11の挟持中心部の回転軌跡Mと、クランクシャフト1のジャーナル部5を中心としたピン部3の中心の回転軌跡Nとの交点Pに位置させる。 - 特許庁
Since a screen displayed in the front-side mode M11 can correspond to various statuses such as the vehicle approaching an intersection at a crossover point, passing near another vehicle, moving toward the roadside or the like, the statuses of the necessary regions in the vicinity of the vehicle 9 can be confirmed without changing over the display mode by the user. 前側方モードM11で示される画面は、交差点への進入、すれ違い、幅寄せなどの想定される様々な状況に対応可能であることから、ユーザは表示モードを切り替えることなく、車両9の周辺の必要な領域の状況を確認することができる。 - 特許庁
The maximum stoppable speed VS capable of stopping the vehicle before the vehicle enters the intersection is further calculated, then the activation of control for avoiding the collision is suppressed even if the present speed is lower than the passing speed VT when the present speed VN of the vehicle is lower than the stoppable speed VS. また、車両が交差点に進入するまでに停止可能な最大速度VSを算出し、車両の現在の速度VNが該停止可能速度VSより小さいときには、該現在の速度が通過可能速度VTより小さくても、衝突回避のための制御の発動を抑制する。 - 特許庁
In the sheet type sliding member 6, the proceeding of wear in a woven cloth due to rubbing between respective threads is suppressed by performing heat treatment in a state of the cloth woven with threads containing the fibers of fluorocarbon resin at a temperature equal to or higher than the melting point of the fluorocarbon resin to induce fusion at the intersection of respective threads. フッ素樹脂の繊維を含む糸で織られた布の状態で当該フッ素樹脂の融点以上の温度で加熱処理を施すことにより糸と糸の交点において融着を起こさせ、糸同士の擦れ合いによる織布の摩耗の進行を抑えたシート状摺動部材6である。 - 特許庁
A position obtained by projecting a position of the target 3 to a horizontal surface deviates by R1 from an intersection of a straight line L1 extended in the direction of the search target 3 when viewed from the camera 2 and the horizontal surface since the search target 3 is located at a height H from the horizontal surface. 目標物3の位置を水平面に投影した位置は、捜索目標物3が水平面から高さHの位置に有るので、カメラ2から見て捜索目標物3の方向に延ばした直線L1と、水平面との交点からR1だけずれた位置となる。 - 特許庁
The cleaning sheet for the fixing member is formed of nonwoven fabric where all aromatic polyamide fiber is fixed by polyester resin solidified in a non-fiber state at a fiber intersection, and a crystallizing peak is not drawn on a DSC curve drawn by measuring the nonwoven fabric in terms of differential scanning heating value. 本発明の定着部材用クリーニングシートは、全芳香族ポリアミド繊維が繊維交点に非繊維状態で凝固したポリエステル樹脂によって固定された不織布からなり、この不織布を示差走査熱量測定して描いたDSC曲線に結晶化ピークが描かれないことを特徴とする。 - 特許庁
The transient wire portion 3b connecting the two winding portions 3a crosses a coil end 3c led out from the winding portion 3a of one field coil 3A, and the intersection X is set at a position separated from the winding portion 3a of the field coil 3A not to overlap the winding portion 3a. この二つの巻線部3aを接続する渡り線部3bは、一方の界磁コイル3Aの巻線部3aから引き出されたコイル端部3cと交差しており、その交差部Xが一方の界磁コイル3Aの巻線部3aと重ならない様に、巻線部3aから外れた位置に設定されている。 - 特許庁
When a congestion line 29 of vehicles to be turned right extends from a right-turn shunt lane 30 to a straight through lane 32 at an intersection, congestion information is transmitted from a vehicle-to-vehicle communication device of an in-vehicle navigation system of the backmost vehicle 31 to a vehicle 33 traveling posteriorly. 交差点において、右折するための渋滞車列29が右折待避レーン30から直進レーン32にまで延びると、最後尾車両31が車載ナビゲーション装置の車々間通信機により、後方を走行する車両33に対して渋滞情報を発信する。 - 特許庁
The keyboard controller 11 includes a first set of pins 100-115 connected to the vertical connecting cables, a second set of pins 200-207 connected to the lateral connecting cables, and a keyboard identification output pin 300 connected to the keyboard identification connecting cable to receive the switch states of the second intersection points 16. キーボードコントローラ11は、縦の接続ケーブルに接続される第1組ピン100〜115、横の接続ケーブルに接続される第2組ピン200〜207及びキーボード識別接続ケーブルに接続され、第2交差点16のスイッチ状態を受信するキーボード識別出力ピン300を備える。 - 特許庁
The angle θ of intersection of laser light 65 with a reference line 66 perpendicular to an exposed surface 30a of the recording paper sheet is so set that 0.5°≤θ≤2° and thus the shift in exposure position due to the influence of reflected light 65 and feed irregularity of the conveying mechanism is suppressed. レーザー光65は、記録紙シート30の露光面30aに垂直な基準線66と交差する交差角度θが、0.5°≦θ≦2°に設定されており、反射光65による影響、及び搬送機構の送りムラによる露光される位置のずれを抑制している。 - 特許庁
A navigation unit 30 transmits intersection data of an ID0001 to an A/T unit 10 via a communication line 70, and a gateway 50 for permitting communications of data having the ID0001 from an information system network B to a control system network A is provided between the units 10 and 30. ナビゲーションユニット30はID0001の交差点データを通信線70を介してA/Tユニット10へ送信し、ユニット10,30間にはID0001を有するデータを情報系ネットワークBから制御系ネットワークAへ通信許可するゲートウェイ50が設けられている。 - 特許庁
The system is constituted such that when a voltage is impressed between metal tube 3 and metal plating 41 in the discharge tube 4, while making oxygen flow to the fillet parts 20 made in the intersection of the metal plates 2 and the discharge tube 4, ozone is generated by generating creeping discharge at the fillet part 20. 金属板2と放電管4との交差部に構成される隅部20に酸素を流しながら、金属管3と放電管4内部の金属めっき41との間に電圧を印加して隅部20にて沿面放電を起こさせることによりオゾンを発生するようになっている。 - 特許庁
Consequently, the focus given by the intersection between axes 302 and 304 in the photographing directions of the cameras 201 and 202 is variably adjusted on the basis of the extent of movement of the hinge 101 because the photographing directions of the cameras 201 and 202 are varied in accordance with movement (folding operation) of the hinge 101. したがって、第一および第二カメラ201および202の撮影方向はヒンジ101の動き(折畳み動作)に連動して変化するので、ヒンジ101の動き量に基づいてカメラ201と202の撮影方向の軸302と304の交点で示される焦点は可変に調整される。 - 特許庁