「negative zero」を含む例文一覧(174)

<前へ 1 2 3 4
  • When the write polarity controlling signal PN is "H", the odd-numbered output terminals and the even-numbered output terminals apply a reset voltage to be a positive polarity zero gradation voltage to the pixel electrodes in the first half "on" period and a negative polarity data voltage to the pixel electrodes in the latter half"on" period.
    また、書込極性制御信号PNが”H”時に、奇数出力端子及び偶数出力端子は、前半オン期間中には正極0階調であるリセット電圧を画素電極に印加し、後半オン期間中には負極データ電圧を画素電極に印加する。 - 特許庁
  • A controller prescribes the zero level of the movable body for the reference frame in at least one "x" or "z" direction by making a scan along the first grating, and the alignment marker causes both first positive and negative orders to shift in phase of response between scan stages.
    コントローラは、xおよびzの少なくとも1方向にて基準フレームに対する可動物体のゼロレベルを、第1グレーティングに沿ったスキャンを実行することによって規定し、スキャン段階の間にアライメントマーカが第1の正および負の次数両方の応答の位相に変化を引き起こす。 - 特許庁
  • A simulation body 10 performs simulation calculation by discretion of a differential equation showing a time change quantity of material concentration in an activated sludge model in a period of calculation distortion width Δt, and corrects, when a material concentration having a negative value appears in the calculation process, it to zero.
    シミュレーション本体10は、活性汚泥モデルにおける物質濃度の時間変化量を表す微分方程式を離散化して計算歪み幅Δtの周期で計算し、計算過程で負の値をとる物質濃度が現れたときにそれをゼロに補正したシミュレーションを行う。 - 特許庁
  • That is, when a write polarity controlling signal PN is "L", odd-numbered output terminals and even-numbered output terminals apply a reset voltage to be a negative polarity zero gradation voltage to the pixel electrodes in the first half "on" period and a positive polarity data voltage to the pixel electrodes in the latter half "on" period.
    即ち、書込極性制御信号PNが”L”時に、奇数出力端子及び偶数出力端子は、前半オン期間中には負極0階調であるリセット電圧を画素電極に印加し、後半オン期間中には正極データ電圧を画素電極に印加する。 - 特許庁
  • The controller of the communication center retrieves the balances of the prepaid communication charges on a call origination side and a call termination side (S1 and S4), when a call is terminated, and when even one of them is negative or zero, the call origination (S2 and S5) is denied and reports that effect to a call origination side (S3 and S6).
    通信センタの制御装置は、発信があったときに、発信側及び着信側の前払い通話料金の残高を検索し(S1,S4)、いずれか一方でもマイナスもしくはゼロであれば、発信を拒否する(S2,S5)と共に発信側にその旨を報知する(S3,S6)。 - 特許庁
  • Since the load ΔW1 is increased by moisture adsorbed/moisture absorbed on the force coil 12 part of an electromagnetic force balancing mechanism part 1 for balancing the load with the electromagnetic force, and thereby, zero-point drift in the negative direction is generated, a humidity correction member 6 for canceling it is fixed onto the under side of a measuring pan 17.
    荷重と電磁力の平衡をとる電磁力平衡機構部1のフォースコイル12部分に吸着、吸湿する水分によって荷重△W1が増加しこれによりマイナス方向のゼロ点ドリフトが生じるので、これを打消す湿度補正部材6を測定皿17の下側に固着する。 - 特許庁
  • To provide an image display device using a spacer 103 which can significantly reduce an effect of charging to an electron orbit without depending on electroconductivity of the spacer 103 itself, and a characteristic of a material by making effectual charging quantity zero by controlling positive and negative charge distributions generated on a surface of the spacer 103.
    スペーサ103表面に生じる正負の帯電分布を制御することで、実効的な帯電量をゼロとし、スペーサ103自身の導電性や、材料の特性によることなく、帯電が電子軌道に与える影響を大幅に低減することができるスペーサ103を用いた画像表示装置を提供する。 - 特許庁
  • (1) The flying object consists of a lightweight sheet and lightweight aggregate, has face structure capable of maintaining its shape, (2) has a main plane having a positive or zero camper and a dihedral angle and a horizontal tail plane having a negative angle of elevation and (3) a tensile center of string for flying it as a kite is located in front of an aerodynamic center.
    (1)軽量のシートと軽量の骨材からなり、自形を維持できる面構造体であり、(2)正または零のキャンパーを有し上反角を有する主翼と、負の迎角を有する水平尾翼とを有し、(3)凧として飛行させるための糸の張力中心が、空力中心より前方に位置する飛翔体。 - 特許庁
  • A CPU judges that a toner replenishing motor 104 is faulty when the rotational amount of a screw 103 detected by a detector 106 is zero despite of that the driving of the motor 104 is switched to negative rotation by the CPU when the screw 103 gets in an abnormal stopping state.
    CPUは、スクリュー103の異常な停止状態時に、CPUによるトナー補給モータ104の駆動を負回転に切り換え設定した後、この切り換え設定にも拘らず、ディテクタ106によって検知されたスクリュー103の回転量が0であるときにはトナー補給モータ104が故障していると判断する。 - 特許庁
  • The ECU 30 determines whether or the turbine rotational sensor NT is a negative rotational frequency when a throttle opening TH detected by a throttle opening sensor 46 is zero, a brake pedal 36 is ON, and a wheel speed VW detected by the wheel speed sensor 34 is a value when the vehicle 1 is substantially stopped.
    ECU30は、スロットル開度センサ46が検知したスロットル開度THが0であり、ブレーキペダル36がオンし、車輪速センサ34が検知した車輪速VWが車両1が実質的に停止した状態のときの値である場合に、タービン回転数NTが負の回転数か否かを判定する。 - 特許庁
  • A wide angle projection lens comprises: a first lens group G1 which has a negative refractive power and has at least one aspheric surface; a second lens group G2 which has a substantially zero refractive power and in or near which an aperture stop is provided; and a third lens group G3 which has a positive refractive power.
    広角投映レンズは、少なくとも1つの非球面を有する、負の屈折力の第1のレンズ群G1と、屈折力が実質的に0であり、内部またはその近傍に開口絞りがある第2のレンズ群G2と、正の屈折力の第3のレンズ群G3とを含み、以下の条件(1)〜(3)を満足する。 - 特許庁
  • In controlling the internal combustion engine, if specified operation conditions are established for allowing retard restriction on ignition timing, and at the same time, either of a rate of change of the command torque and a rate of change of estimated torque is negative, then, the amount of retard of the ignition timing is set at zero, even in such a state that the estimated torque is higher than the command torque.
    点火時期の遅角を制限することが許容される所定の運転条件が成立しており、かつ、目標トルクの変化率又は推定トルクの変化率の何れかが負の場合には、推定トルクが目標トルクよりも大きい状況であっても点火時期の遅角量はゼロに設定する。 - 特許庁
  • In the cam device 1 which can change the displacement stroke length of the follower 9 by using the oscillating cam 7 oscillated by the rotation cam 5 to thereby displace the follower 9, the follower 9 is so arranged as to be lifted when the value of the oscillating acceleration of the oscillating cam 7 is zero or negative.
    回転カム5によって揺動し、この揺動により従動節9を変位させる揺動カム7を用いて、上記従動節9の変位行程長を変更可能なカム装置1において、上記揺動カム7の揺動加速度が、ゼロまたは負の値にあるときに、上記従動節9がリフトするように構成されている。 - 特許庁
  • The in-phase indicator lamp drive circuit extracts timing signals in a region changing from a negative electrode to a positive electrode, using as the center the zero-point voltage crossing region of the highest inclination in the voltage change, with respect to the phase change in the alternating current sine waves of the power source inputs input, respectively from the first and second input ends, and compares these two timing signals.
    同相表示灯駆動回路は、第1および第2の入力端からそれぞれ入力する電源入力である交流正弦波に対し位相変化に対する電圧変化傾斜の最も大きいゼロボルトを中心とし、正極から負極に変化する領域のタイミング信号をそれぞれ抽出し、これら2つのタイミング信号を比較する。 - 特許庁
  • The inverter 200 has first and second main switches which are interposed in series between two positive and negative power lines extended from a common rectifier 100 and are turned on and off by turns, and a soft switching unit which controls switching so that voltage at both ends of the first and second main switches becomes zero to flow no current when the first and second main switches are turned on.
    インバータ200は、共通整流器100から延びる正負2種類の電源ラインの間に直列に挿入されて交互にオン/オフされる第1および第2の主スイッチと、これらの主スイッチをオンするときにその両端電圧が0Vであって流れる電流が0Aとなるように制御するソフトスイッチング部とを有する。 - 特許庁
  • The displacement sensor 10 includes a control part 16 for successively reading light receiving signals, secondarily differentiating the light receiving signals by a time to generate second order differential signals, setting a light receiving signal level of pixels in a threshold at a zero cross point changed from a positive value to a negative value with the second order signals, and setting a pixel range of the threshold or more in a calculation range.
    変位センサ10は、受光信号を順次読み込み、受光信号を時間で二次微分して二次微分信号を生成し、その二次微分信号が正値から負値に変化するゼロクロス点における画素の受光信号レベルをしきい値に設定し、そのしきい値以上の画素範囲を演算範囲に設定する制御部16を備える。 - 特許庁
  • A characteristic of the torque commands for suppressing the roll back of the car stored in the torque map 12, is a forward characteristic which has a positive torque command, when the rotational speed of the motor is zero, and increases gradually in the positive direction as the rotational speed of the motor increases in the negative direction, when the wheels are driven by the motor in the forward direction.
    トルクマップ12に記憶された車両のロールバックを抑制するためのトルク指令値の特性は、モータが車輪を前進方向に駆動するようにされている場合においては、モータの回転速度が0のときはトルク指令値が正の値で回転速度が負方向に増加するにつれて正方向に次第に増加する前進側特性である。 - 特許庁
  • Further, reception signals and image signals of transmission signals, both having the intermediate frequency A and being contained in these transmitted signals, are respectively converted into reception signals having the intermediate frequency B and image signals having the intermediate frequency C, both having positive and negative carrier frequencies symmetrical to a direct current component having a frequency of zero and being represented as a complex number, by a quadrature detector 18.
    更に、この信号に含まれる中間周波数Aの受信信号と送信信号のイメージ信号とを、直交検波器18により、周波数ゼロの直流成分に対称な正負の搬送波周波数を持つと共に複素数で表された中間周波数Bの受信信号と中間周波数Cのイメージ信号とへそれぞれ変換する。 - 特許庁
  • A voltage comparator CP output of which becomes a zero level and a high level respectively when a magneto coil 1 generates a positive half-wave output voltage and when the magneto coil generates a negative half- wave output voltage, and a transistor TR3 which conducts when output of the comparator CP is at a high level, to prevent output of a signal coil 2 from being given to a CPU 5, are provided.
    発電コイル1が正の半波の出力電圧を発生しているとき及び負の半波の出力電圧を発生しているときにそれぞれ出力が零レベル及び高レベルになる電圧比較器CPと、比較器CPの出力が高レベルになっているときに導通して信号コイル2の出力がCPU5に与えられるのを阻止するトランジスタTR3 とを設ける。 - 特許庁
  • The in-phase indicator lamp drive circuit extracts timing signals in a region changing from a negative electrode to a positive electrode, using as the center the zero-point voltage crossing region of the highest inclination in the voltage change, with respect to the phase change in the alternating current sine waves of the power source inputs input respectively from the first and second input ends, and compares these timing signals to determine the in phase.
    同相表示灯駆動回路は、第1および第2の入力端からそれぞれ入力する電源入力である交流正弦波に対し位相変化に対する電圧変化傾斜の最も大きいゼロボルトを中心とし、負極から正極に変化する領域のタイミング信号を抽出し、これらタイミング信号を比較することにより同相を判定する。 - 特許庁
  • Since the temperature-dependency of the center wavelength is determined by the difference between temperature-dependencies of equivalent refractive indexes, any of filters having positive, zero, and negative temperature-dependencies of the center wavelength respectively can be achieved regardless of signs of temperature-dependencies of equivalent refractive indexes by controlling the relation between the temperature-dependency of an equivalent refractive index in a fundamental mode and that in a first-order mode.
    等価屈折率の温度依存性の差により中心波長の温度依存性が決定されるため、基本モードの等価屈折率の温度依存性と1次モードの等価屈折率の温度依存性の大小関係を制御することにより、等価屈折率の温度依存性の符号にかかわらず、中心波長の温度依存性が正、ゼロ、負のいずれのフィルタも実現することができる。 - 特許庁
  • In an iron or utility golf club set comprising a plurality of clubs whose loft angle gets larger as a number gets larger, an offset amount is almost zero for one club (reference club) in the middle of the numbers, the offset amount is negative for the club whose number or loft angle is smaller than that, and the offset amount is positive for the club whose number is larger than that.
    番手が大きくなるほどロフト角が大きくなる複数本のクラブよりなるアイアン又はユーティリティゴルフクラブセットにおいて、番手の途中の1本のクラブ(基準クラブ)は、オフセット量がほぼゼロであり、それよりも番手又はロフト角が小さいクラブはオフセット量が負であり、それよりも番手が大きいクラブはオフセット量が正であることを特徴とするゴルフクラブセット。 - 特許庁
  • At the automatic start from the idling stop, an intake air quantity is controlled by changing intake valve closing timing IVC by a variable valve train when the flag fFMBSH is set to zero, and intake pipe negative pressure is increased by controlling an intake air quantity by an throttle opening with the intake valve closing timing IVC set near the bottom dead center when the flag fFMBSH is set to 1.
    そして、アイドリングストップからの自動始動において、フラグfFMBSHに零がセットされている場合には、可変動弁機構によって吸気バルブの閉時期IVCを変化させることで、吸入空気量を制御させ、フラグfFMBSHに1がセットされている場合には、吸気バルブの閉時期IVCを下死点付近に固定し、スロットル開度で吸入空気量を制御させ、吸気管負圧を増大させる。 - 特許庁
  • The ionizer utilizing the soft X-ray comprises: a head part for generating the soft X-ray in order to make a potential of a charged object zero by either one or more of positive ions, negative ions, and electrons generated from ionized gas, wherein the gas in air is ionized by the soft X-ray discharged to the charged object; and a control part for controlling the one or more head parts.
    この発明は、帯電物体に向けて軟X線を放出し、放出された軟X線によって空気中のガスを電離させ、電離されたガスから発生されるプラスイオン、マイナスイオン及び電子のうちの何れか1つ以上によって前記帯電物体の電位を0にするために軟X線を生成させるヘッド部と、1つ以上の前記ヘッド部を制御するための制御部とを具備してなる軟X線を利用したイオナイザーに関するものである。 - 特許庁
<前へ 1 2 3 4

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.