In this object measuring device by the variable natural oscillation cantilever, the natural frequency of the cantilever 201 due to the application of light energy from the outside is controlled to be varied in the predetermined range, and characteristics of a substance as a sample are measured by controlling the natural frequency of the cantilever 201. 固有振動可変型のカンチレバーによる測定対象物の計測装置において、外部からの光エネルギーの付加によるカンチレバー201の固有振動数を所定幅で可変になるように制御し、このカンチレバー201の固有振動数の制御によって試料としての物質の特性を計測する。 - 特許庁
When a diesel engine is operated in a high-load range at highlands, the increase of NOx is suppressed by increasing the recirculated flow amount of exhaust gas and a gear shift ratio in a continuously variable transmission is changed to a low speed side at a constant output to shift the rotational speed of the engine to a high rotation side where exhaust gas particulates are hard to occur. 高地でディーゼルエンジンが高負荷域で運転されているときには、排気還流量を増加させることでNOxの増大を抑止し、かつ、出力一定で無段変速機における変速比を低速側に変更して、エンジンの回転速度を排気微粒子が発生しにくい高回転側にシフトさせる。 - 特許庁
To enable an AC motor driven by an alternating-current which has been converted by an electric power converter to perform variable speed control stably by keeping a current control stable even if the AC motor accelerates or decelerates abruptly or a load is rapidly changed in a range where an output voltage of the electric power converter becomes saturated. 電力変換器により変換された交流により駆動される交流電動機が、電力変換器の出力電圧が飽和する領域において、急に加減速したり負荷が急変した場合であっても、電流制御を安定に保つことにより、交流電動機を安定に可変速制御できるようにする。 - 特許庁
Thereby, when the excitation light power of the excitation light outputted from the excitation light source 1a is made low, excitation light absorbing quantity of the rare earth added optical fiber 1c is made large, and the excitation light source 1a stably operates upon the minimum gain and a wide gain variablerange can be obtained in the Raman amplifier 1. これにより、励起光源1aから出力される励起光の励起光パワーが小さくなると、希土類添加光ファイバ1cの励起光の吸収量が大きくなり、ラマン増幅器1は、最小利得時に励起光源1aが安定して動作するとともに、広範囲の利得可変範囲を得ることができる。 - 特許庁
To provide a sodium-sulfur battery module capable of allowing the temperature of a gas sump of a variable conductance heat pipe to rise when the operation is started upon attaining the rated output from a large-output operation, lowering the cooling ability of the heat pipe, preventing the battery temperature to drop, maintaining the proper operating temperature range, and yielding the desired output and energy efficiency. 高出力運転から定格出力にして運転した際には可変コンダクタンス型ヒートパイプのガス溜めの温度を上昇させ、ヒートパイプの冷却能力を低下させ、電池温度が低下することを防止し、適正な運転温度領域を維持して、所望の出力とエネルギー効率を出すことにある。 - 特許庁
A valve 6 for variable control of the opening of the bypass passageway 7 and an oxidation catalytic maniverter 8 are mounted on the bypass passageway 7, thereby retaining the temperature of the exhaust supplied to the oxidation catalytic converter 5 within the active temperature range of catalyst by the bypass exhaust with an increased temperature due to an oxidation process by the maniverter 8. バイパス通路7の開度を可変制御するバルブ6および酸化触媒タイプのマニバータ8をバイパス通路7に設けたことにより、マニバータ8による酸化作用で温度上昇したバイパス排気で酸化触媒コンバータ5に供給される排気の温度を触媒の活性温度範囲内に保持させるようにした。 - 特許庁
Because the irradiation direction of the light irradiated from the attracting light source 2 is variable by the reflector 9 and the light illuminance in the irradiation object can be retained constantly, the illuminance necessary to attract insects to the adhesive sheet 8 can be obtained over the wide range without installing a plurality of attracting light sources 2. 誘引光源2から照射された光は反射板9により照射方向が可変であり、かつ照射対象における光照度を一定に保持できるので、誘引光源2を複数設けなくとも、虫を粘着シート8へ誘引するのに必要な照度が広範囲に渡って得られる。 - 特許庁
To avoid the situation that feedback control before lock release disturbs the lock release, in a variable valve timing controller having a function for locking a cam shaft phase at a middle lock position positioned at a nearly middle point in a controllable range of the cam shaft phase during a stop of an internal combustion engine or when starting the engine. 内燃機関の停止中及び始動時にカム軸位相をその調整可能範囲の略中間に位置する中間ロック位置でロックする機能を備えた可変バルブタイミング制御装置において、ロック解除前のフィードバック制御によりロック解除が妨げられる事態を回避できるようにする。 - 特許庁
When the high frequency power amplifier 5 is operated as a non-linear amplifier, the input level of the high frequency power amplifier 5 is changed according to the average output power of transmission signal using a variable gain amplifier 7 so that leak power is reduced for the wider control range of the transmission output power. さらに、高周波電力増幅器5が非線形増幅器として動作する時に、高周波電力増幅器5の入力レベルを可変利得増幅器7により送信信号の平均出力電力に応じて変化させることにより、リーク電力を低減して送信出力電力の制御範囲を広くとることができる。 - 特許庁
An optical level adjusting control unit 18 generates a control signal on the basis of a monitoring result within an input level range of a post-amplifier 12 so that optical levels of all wavelengths become the same, and performs control adjustment of the optical levels of the first and second optical variable attenuators 14, 15. 光レベル調整制御部18は、モニタ結果にもとづいて、ポストアンプ12の入力レベル範囲内で、かつ各波長の光レベルがすべて同一値となるように、制御信号を生成して、第1の光可変減衰器14及び第2の光可変減衰器15の光レベルの調整制御を行う。 - 特許庁
To provide a variable-pitch blade control device using a flexible rod which has very good resistance to mechanical fatigue brought about by repeated actuation and very high resistance to buckling, while at the same time having a flexibility that allows it easily to deform in torsion, in the entire range of rotation of a control ring. 反復動作により生じる機械的疲労に対して非常に良好な耐性を有すると共に、座屈に対しても非常に高い耐性を有し、同時に制御リングの全回転範囲において容易に捻り変形を可能とする柔軟性をも有する弾性ロッドを使用した可変ピッチブレード制御装置を提供する。 - 特許庁
To improve control response by reducing variable control start necessary pressure difference of swash plate angles and improve controllability by enabling to perform minute displacement change easily and accurately in a low displacement range in relation to control of a control valve in a swash plate compressor. 斜板式圧縮機において、制御弁による制御に関して斜板角度の可変開始必要差圧を低減することにより制御応答性の向上をはかるとともに、低容量域においては微小な容量変更を容易にかつ精度良く行うことができるようにして制御性の向上をはかる。 - 特許庁
This change gear ratio control method includes a target change gear ratio calculating step for calculating a target change gear ratio within the range from the minimum value to the maximum value of plural change gear ratios corresponding to plural preset engine operating modes, and a transmission control step for controlling the continuously variable transmission according to the target change gear ratio. 予め設定された複数個のエンジン作動モードに該当する複数個の変速比の最少値乃至最大値の範囲内で目標変速比を算出する目標変速比算出段階と;前記目標変速比に応じて無段変速機を制御する変速機制御段階とを含むことを特徴とする。 - 特許庁
An FCD on-vehicle machine re-samples a traveling route of traveling with measuring a position in a re-sampling section length set in conformation to the radius of curvature range of a road, represents the position information of a sampling point by a parameter having a statistical deviation, encodes the value of the parameter in variable length, and transmits it to an FCD collection device. FCD車載機は、位置を計測しながら走行した走行経路を、道路の曲率の範囲に対応付けて設定したリサンプル区間長でリサンプルし、サンプリング点の位置情報を統計的に偏りを持つパラメータで表し、このパラメータの値を可変長符号化してFCD収集装置に送信する。 - 特許庁
The continuously variable automatic transmission mechanism has a pulley member formed by a pair of opposed half pulleys 4, 6 on an input shaft 2 for inputting the power of a motor 1 and includes an input-side slide regulating means 60, 7a for regulating at least the half pulley 6 to slide within a predetermined range only in a direction parallel to the axial direction of the input shaft. モータ1の動力を入力する入力軸2上において1対の対向するハーフプーリ4・6でプーリ体を形成し、少なくとも一方のハーフプーリ6が該入力軸の軸方向と平行な方向にのみ所定の範囲内で摺動するように規制する入力側摺動規制手段60・7aを備える。 - 特許庁
Then, a control signal corresponding to the instruction opening degree θ is output to the variable turbocharger to control the opening degree (S18) while the instruction opening degree θ is increased and decreased within a range demarcated by a lower limit opening degree and an upper limit opening degree (S13 to S17) so that the temperature T of exhaust flowing in the DPF approaches a prescribed temperature. そして、DPFに流入する排気温度Tが所定温度に近づくように、下限開度及び上限開度で画定される範囲内で指示開度θを増減させつつ(S13〜S17)、可変ターボチャージャに対して指示開度θに応じた制御信号を出力して開度を制御する(S18)。 - 特許庁
A signal strength control circuit 140 controls the gain of a variable gain amplifier 120 into value capable of effectively using a bit resolution within a range not to exceed the allowable signal strength of the input signal of an A/D converting circuit 60 and also controls the signal strength of an up signal from a subscriber side modem 40. 信号強度制御回路140は、A/D変換回路60の入力信号の信号強度許容値を越えない範囲で、かつビット分解能を有効に使用できる値になるように、利得可変アンプ120の利得を制御し、加入者側モデム40からの上り信号の信号強度を制御する。 - 特許庁
An SMR welding determining portion 162 changes a voltage command value VL*, which is a target value when a converter drops a motor operation voltage in a VL constant control, to a lower pressure side and a higher pressure side than the variablerange of a DC voltage VL acquired in advance when the battery is connected. SMR溶着判定部162は、VL一定制御においてコンバータがモータ動作電圧を降圧するときの目標値である電圧指令値VL*を、予めバッテリを接続した状態にて取得されている直流電圧VLの変動範囲よりも低圧側および高圧側に変動させる。 - 特許庁
When a shift lever is put into the low-speed range during the snow removing operation, changing-over into the motor shift mode is made in which gear shifting is performed by transmitting to a running device the differential output formed from a constant output of the HST (hydrostatic type continuously variable transmission device) and the output complying with the shift lever turning amount (angle) of the electric motor. 除雪作業中は、変速レバーが低速域に入力された場合、HST(静油圧式無段変速装置)の一定出力と電動モータの変速レバーの操作量(変速レバー角度)に応じた出力との差動出力を走行装置に伝達して変速するモータ変速モードに切り換える。 - 特許庁
In a Pachislot machine 1, when a special game state is achieved, special stop control is executed which selects derivable symbols within the range of second maximum delay time shorter than first maximum delay time which is the maximum delay time in a normal game state in a specified display column, derives the selected symbols and stops variable display. パチスロ1では、特別遊技状態になると、特定の表示列において通常遊技状態における最大遅延時間である第1の最大遅延時間よりも短い第2の最大遅延時間の範囲内で導出可能な図柄を選択し、選択した図柄を導出して変動表示を停止させる特別停止制御を行う。 - 特許庁
Movement of a scattering-proof grid in a radiography instrument results in a continuous curve (CB) wherein its time coordinate is equal to a half of the above decribed exposure time (TP) and space differential of time variable on it is symmetric with respect to a point (SP) with two straight parts being symmetric with respect to a symmetric axis passing through the center in the range of movement of the grid. X線撮影装置中の散乱防止グリッドの移動は、その時間座標が前記露光時間(TP)の半分に等しく、かつそれについての時間変数の空間微分が、グリッドの移動範囲の中央を通る対称軸について対称な2つの直線部分を有する点(SP)について点対称となる連続曲線(CB)となる。 - 特許庁
When the lens unit 10 incorporating the CCD is set to the camera main body unit 20, the camera main body unit 20 takes in information indicating the photographing range from the lens unit 10 incorporating the CCD, and a visual field frame formed by a variable power lens 32 of the see-through finder 30 and a liquid crystal panel 35 is controlled based on this information by a finder control part 40. CCD内蔵レンズユニット10がカメラ本体ユニット20に装着されると、カメラ本体ユニット20はCCD内蔵レンズユニット10からその撮影範囲を示す情報を取り込み、この情報に基づいてファインダ制御部40によって透視ファインダ30の変倍レンズ32や液晶パネル35によって形成される視野枠を制御する。 - 特許庁
Even when identification image information formed by the last stop of the identification information after an identification information image displayed on a display device 32 shifts into a ready-to-win state, is a miss, if the identification information stopped last is an odd number, variable displays are repeatedly made until getting out of the prescribed condition range again in the ready-to-win state. 表示装置32において表示される識別情報画像がリーチ状態に移行した後、最後に識別情報が停止して構成された識別画像情報が外れであっても、その最後に停止した識別情報が奇数であれば再度リーチ状態で前記所定の条件範囲外になるまで繰り返し変動表示が行われるように構成する。 - 特許庁
To provide a PLL(Phase Locked Loop) control method and a PLL circuit which can solve a problem of an unstable output of a voltage controlled oscillator when the frequency of an input signal is not within a variablerange of the voltage controlled oscillator or when the input signal is absent and which can give a stable output even when the input signal includes sudden fluctuations. 従来の入力信号の周波数が電圧制御発振器の可変範囲でない場合や、入力信号がない場合に、電圧制御発振器の出力が安定しないという問題点を解決し、入力信号に突発的な変動があっても安定した出力を得られるPLL制御方法及びPLL回路を提供する。 - 特許庁
In the first variable power range, in a state where the first lens frame 70 is supported by the first cam barrel 10 and the second lens frame 80 is supported by the second cam barrel 20, they are moved back and forth along the optical axis L by the third cam barrel 30, whereby a distance between the first lens group 101 and the second lens group 102 is changed. 第1の変倍範囲においては、第1のレンズ枠70は第1のカム筒10により支持され、第2のレンズ枠80が第2のカム筒20によって支持された状態で第3のカム筒30によって光軸Lに沿って前後することにより、第1のレンズ群101と第2のレンズ群102との距離が変えられる。 - 特許庁
The performance determination means 132 selects, according to a lottery result of one or more ball entry reported by the information forenotice means 157, a performance pattern of a consecutive performance continued across a symbol variable display corresponding to the entry of one or more balls within a range reported by the information forenotice means 157. 演出決定手段132は、事前情報通知手段157により通知された1以上の入球に対する抽選結果にしたがって、事前情報通知手段157により通知された範囲における1以上の入球に対応する図柄変動表示に亘って継続される連続演出の演出パターンを選択する。 - 特許庁
The architecture has a DC loop for removing DC offset from a signal component, a digital variable gain amplifier (DVGA) for providing a gain range, an automatic gain control (AGC) loop for performing a gain control relating to the DVGA and an RF/analog circuit, and a serial bus interface (SBI) unit for providing control to the RF/analog circuit via a serial bus. 信号成分からDCオフセットを除去するDCループと、利得レンジを提供するデジタル可変利得増幅器(DVGA)と、DVGAとRF/アナログ回路に対して利得制御を行う自動利得制御(AGC)ループと、シリアルバスを介してRF/アナログ回路に対して制御を提供するシリアルバスインターフェイス(SBI)ユニットとを有する。 - 特許庁
To provide a toroidal type continuously variable transmission which prevents a moment force from being generated to a drive piston, and for reducing influence on a moving range of the power roller, while it is possible to rotationally control a sun gear for controlling an inclination angle of a power roller by a hydraulic servo provided on an outer peripheral side of both disks. 両ディスクの外周側に設けられた油圧サーボによってパワーローラの傾斜角度を制御するためのサンギヤを回転制御することが可能でありながら、駆動ピストンにモーメント力が生じることを防ぐと共に、パワーローラの移動範囲に対する影響も少なくすることが可能なトロイダル式無段変速装置を提供する。 - 特許庁
A phase lock detector 11 detects the presence of an intermediate frequency signal, an output of a low frequency oscillator 10 is given to a 2nd control terminal 18 of a VCO 3 when no intermediate frequency signal is received to trace the frequency from an upper limit to a lower limit of an oscillated frequency from the VCO within its variablerange. 中間周波数信号の存在の有無を位相ロック検出器11が検出し、中間周波数信号が入力されていないときは、低周波発振器10の出力がスイッチ21によりVCO3の第2の制御端子18に接続され、VCO3の発振周波数を可変範囲の上限から下限までトレースする。 - 特許庁
Since an optical image is formed on an image pickup element 4 through a transmission filter 3 whose optical transmission factor is selectively variable a dynamic range of the image pickup element is fully utilized by decreasing the transmission factor of the transmission filter 3 partially for only a component of an image with high luminance thereby decreasing a contrast difference from a component with low luminance. 光学像が、選択的に光透過率を変更可能な透過フィルタ3を経て、撮像素子4に結像されるようになっているので、たとえば画像の高輝度な領域だけ部分的に透過フィルタ3の透過率を低くして、それにより低輝度の領域とのコントラスト差を小さくし、撮像素子のダイナミックレンジをフルに活用することができる。 - 特許庁
This reader reads magnetic information by giving priority to an area whose range of a setting amount is wide from piercing areas where punch holes are made in the balance punch hole part E3 of a prepaid card 6 being a processing object, and discriminates whether it is matched with piercing balance information contained in variable information of the card. 読書装置は、処理対象のプリペイドカード6について、残高パンチ孔部E3においてパンチ孔が穿孔されている穿孔領域のいずれか1つから、設定されている金額の範囲が広い領域を優先して、磁気情報を読み取り、そのカードの可変情報に含まれる穿孔残高情報と一致するか否かを判別する。 - 特許庁
In general, in a system provided with a variable valve timing apparatus, the actual valve timing is prevented from getting out of a range in which the engine can start by executing the valve timing maintaining control during the period in which the actual valve timing cannot be calculated in engine start, since actual valve timing is controlled to a position fit for engine start right before engine stop. 一般に、可変バルブタイミング装置を備えたシステムでは、エンジン停止直前に実バルブタイミングをエンジンの始動に適した位置に制御しておくため、エンジン始動時に実バルブタイミングを算出できない期間に、バルブタイミング維持制御を実行することで、実バルブタイミングがエンジンの始動可能な範囲から外れてしまうことを防止することができる。 - 特許庁
To provide a patch type magnetic therapeutic device promoting the blood circulation by magnetism generated from a magnet, enabling a wide-range of therapy while avoiding from growing accustomed thereto by making the magnet movable and forming a variable magnetic field, eliminating discomfort such as pain due to a long period of use, and surely retaining the adhesion. 磁石から生じた磁気により血行を促進するとともに、磁石を移動可能として変動磁場を形成させ広範囲の治療を可能としつつなれを回避することができ、且つ、長時間の使用によっても痛み等の違和感を生じさせず粘着を確実に維持することができる貼付用磁気治療器を提供する。 - 特許庁
A sensor ECU 3 of the sensor signal processing apparatus 6 sets the gain of a variable-gain amplifier 9, which amplifies and outputs analog sensor signals, adds information on the setting of the gain as a range bit to data of sensor signals converted from analog into digital form by an A/D converter 10, and outputs it to an ECU 4 for airbags and an ECU 5 for VSC. センサ信号処理装置6のセンサECU3は、アナログのセンサ信号を増幅して出力する可変ゲインアンプ9のゲインを設定すると共に、A/D変換器10によりA/D変換されたセンサ信号のデータに、前記ゲインの設定に関する情報をレンジビットとして付加し、エアバッグ用ECU4やVSC用ECU5に出力する。 - 特許庁
To provide an optical equipment realizing the variable power and the focusing of an optical system by a single driving source and a driving mechanism by moving the rear group lens frame along an optical axis by the movement of the moving barrel and preventing the movement of a rear group lens frame in a fixed moving range when the direction of the movement of a moving barrel is changed. 移動筒の移動により後群レンズ枠を光軸に沿って移動させ移動筒の移動の方向が変化したときに一定の移動範囲において後群レンズ枠の移動を行わないようにすることにより、単一の駆動源及び駆動機構により光学系の変倍とフォーカシングが行える光学機器を提供すること。 - 特許庁
A gain calculation section 108 estimates an average received signal level at the outside of a dynamic range of the analog/digital converter 102 on the basis of the number of clipping/underflow times within a prescribed period counted by a clipping count section 105 and an underflow count section 106 on the occurrence of the clipping/underflow and adjusts a gain of a variable gain amplifier 101 on the basis of the estimated level. 利得算出部108は、クリッピング/アンダーフロー発生時に、クリッピングカウント部105とアンダーフローカウント部106にてカウントされた一定期間内でのクリッピング/アンダーフロー回数に基づき、A/D変換器102のダイナミックレンジ外における平均受信信号レベルを推測し、それに基づき可変利得アンプ101の利得を調整する。 - 特許庁
The game machine stops or temporarily stops re-variable-patterns on a prescribed range on the valid line and variably displays the patterns on the valid line again at a prescribed timing after stopping or temporarily stopping of the re-variable-pattern to inform the player of getting a special game condition. 始動入賞を受け、特別遊技状態に移行させるか否かを大当り判定プログラムにて決定し、特別遊技状態への移行に係る図柄を所定時間変動表示させた後に有効ライン上に所定数揃えて特別遊技状態に至る否かの旨を遊技者に報知する遊技機であって、有効ライン上の所定領域に、再変動図柄を停止又は仮停止させ、再変動図柄の停止又は仮停止後に、その有効ライン上の図柄を所定のタイミングで再度変動表示させ、特別遊技状態に当選したとの旨を報知することを特徴とする。 - 特許庁
b. The lamp light of said lamp units shall be a constant light in variable white. However, in the case where it is installed within a range either the shorter of one-third of the total runway length or 600 meters from the runway farther threshold (which refers to the farther threshold of a runway as seen from an aircraft intending to land; hereafter the same shall apply as seen from an aircraft intending to land), the light shall be in yellow.
b 灯光は、航空可変白の不動光であること。ただし、着陸しようとする航空機から見て、滑走路終端(着陸しようとする航空機から見て先方にある滑走路末端をいう。以下同じ。)から滑走路の全長の三分の一又は六百メートルのいずれか短い長さの範囲内にあるものにあつては、航空黄であること。 - 日本法令外国語訳データベースシステム
A control part of a digital multifunction machine sets an image read scale factor and a final image printing scale factor (final image formation scale factor) corresponding to a preset variable power processing mode according to a read operation instruction, subsequently checks a preset read range setting mode, and detects an original size if the mode is an original size mode or an original size plus an error mode. デジタル複合機の制御部は、読み取り動作の指示により、予め設定された変倍処理モードに対応する画像読み取り倍率および最終画像印刷倍率(最終画像形成倍率)を設定した後、予め設定された読み取り範囲設定モードをチェックし、そのモードが原稿サイズモード又は原稿サイズ+誤差モードであれば、原稿サイズを検出する。 - 特許庁
When a motor 45 and a suction fan 44 of a belt platen mechanism 104 are driven at each frequency (rotational frequency) within a variablerange, a vibration signal indicating the vibration of the belt platen mechanism 104 is acquired from an output signal of an acceleration sensor 48, and the acquired driving signal is speedily Fourier-transformed to generate a frequency spectrum of a vibration level of the belt platen mechanism 104. ベルトプラテン機構部104のモータ45やサクションファン44を可変範囲内の各周波数(回転数)でそれぞれ駆動したときの、ベルトプラテン機構部104の振動を示す振動信号を、加速度センサ48の出力信号から取得し、取得した駆動信号を高速フーリエ変換して、ベルトプラテン機構部104の振動レベルの周波数スペクトルを生成する。 - 特許庁
To obtain a direct down converting receiver architecture having a DC loop for removing a DC offset from a signal component, a digital variable gain amplifier (DVGA) for providing a gain range, an automatic gain control (AGC) loop for performing gain control relating to the DVGA and RF/analog circuits, and a serial bus interface (SBI) unit for providing control relating to the RF/analog circuits via a serial bus. 信号成分からDCオフセットを除去するDCループと、利得レンジを提供するデジタル可変利得増幅器(DVGA)と、DVGAとRF/アナログ回路に対して利得制御を行う自動利得制御(AGC)ループと、シリアルバスを介してRF/アナログ回路に対して制御を提供するシリアルバスインターフェイス(SBI)ユニットとを有するダイレクトダウンコンバート受信機アーキテクチャを提供する。 - 特許庁
To provide a control device for an internal combustion engine having a function to change relative operation characteristics of an intake valve and an exhaust valve with respect to the rotating operation of a crankshaft of the internal combustion engine and a mechanism for fixing the operation characteristics in the middle of the variablerange, and capable of suitably suppressing deterioration in engine operation performance caused by a malfunction of the mechanism. 内燃機関のクランクシャフトの回転動作に対し吸気バルブや排気バルブの相対的な動作特性を変更する機能を有して、且つ、当該動作特性をその可変範囲の中間で固定する機構を備えた装置において、当該機構の誤作動による機関運転性能の低下を好適に抑制することのできる内燃機関の制御装置を提供する。 - 特許庁
A rasterizer module 2013 outputs layout data in which the range of cutting out in image data, the variable magnification of image data and the printing area of the image data on a printing medium are laid out in a manner that makes them the same between image data equal in size on the basis of printing medium information and layout pattern information and generates printing data on the basis of the layout data. ラスタライザモジュール2013は、印刷媒体情報および割り付けパターン情報を基に、画像データにおける切り出し範囲と、画像データの変倍率と、画像データの印刷媒体上の印刷面積とが画像サイズの等しい画像データ間において同様となるように割り付けた割り付けデータを出力して、その割り付けデータに基づき印刷データを生成する。 - 特許庁
To provide an in-cabin illumination device realizing illumination of the whole in a cabin by effectively utilizing a monitor light of a monitor system for indoor illumination, capable of emitting a light with an optional amount of light and free color tone in a variablerange as a light for illumination and enjoying illumination direction adjusted to occupant's (user) feeling and atmosphere. モニタシステムのモニタ光を室内の照明に有効利用することで、車室内全体の照明が可能になると共に、機能上、可変可能な範囲での任意の光量および自由な色あいで照明用として発光させることができ、搭乗者(利用者)の気分・雰囲気に合わせた照明演出を楽しむことができる車室内照明装置を得る。 - 特許庁
To provide an inexpensive and highly reliable magnetron with a simple structure capable of obtaining powerful microwaves having a desired frequency with a rapid response corresponding to an outside electric signal without using a mechanical means having a movable part, and capable of obtaining a broadly variable oscillation frequency range without arranging a switch element inside a bulb without inhibiting productivity. 可動部を持つ機械式手段によらず、簡単な構造で、外部からの電気信号により所望の周波数の高出力マイクロ波が極めて速いレスポンスで得られ、またスイッチ素子を管球内部に配置することなく、広い可変範周の発振周波数を得ることができ、生産性を阻害することもなく、低価格で信頼性の高いマグネトロンを提供する。 - 特許庁
The docking guide device 10 includes: a guide display board 1 which has a display screen 1a having a horizontally long rectangular shape which is disposed toward the sea side and displaying a variable guide pole 11 changeable in position within a range of its horizontal length; and a fixed guide pole 2 disposed at the front center of the display screen away from the screen surface by a predetermined distance. 着岸誘導装置10が、横長方形の表示画面1aを有し、表示画面が海側に向けて配置され、表示画面にその横長の範囲で位置が変化される可変誘導柱11が表示される誘導表示盤1と、表示画面の前面中央に画面表面から所定距離離間されて配置される固定誘導柱2とを備える。 - 特許庁
A direct downconversion receiver architecture has a DC loop to remove DC offset from the signal components, a digital variable gain amplifier (DVGA) to provide a range of gains, an automatic gain control (AGC) loop to provide gain control for the DVGA and RF/analog circuitry, and a serial bus interface (SBI) unit to provide controls for the RF/analog circuitry via a serial bus. 信号成分からDCオフセットを除去するDCループと、利得レンジを提供するデジタル可変利得増幅器(DVGA)と、DVGAとRF/アナログ回路に対して利得制御を行う自動利得制御(AGC)ループと、シリアルバスを介してRF/アナログ回路に対して制御を提供するシリアルバスインターフェイス(SBI)ユニットとを有するダイレクトダウンコンバート受信機アーキテクチャとした。 - 特許庁
The direct downconversion receiver architecture includes: a DC loop to remove DC offset from signal components; a digital variable gain amplifier (DVGA) to provide a range of gains; an automatic gain control (AGC) loop to provide gain control for the DVGA and RF/analog circuitry; and a serial bus interface (SBI) unit to provide controls for the RF/analog circuitry via a serial bus. 信号成分からDCオフセットを除去するDCループと、利得レンジを提供するデジタル可変利得増幅器(DVGA)と、DVGAとRF/アナログ回路に対して利得制御を行う自動利得制御(AGC)ループと、シリアルバスを介してRF/アナログ回路に対して制御を提供するシリアルバスインターフェイス(SBI)ユニットとを有するダイレクトダウンコンバート受信機アーキテクチャ。 - 特許庁
The communication apparatus for coding transmission data, based on a parameter group for processing the transmission data, comprises a coding unit which adaptively selects a coding operation algorithm according to the width of an allowable range of a parameter variable during communication (a parameter not needed to send change information with a message between apparatus), contained in the parameter group. 本発明の通信装置は、送信データを加工するためのパラメータ群に基づいて、送信データを符号化する通信装置であって、前記パラメータ群に含まれる通信中に変化可能なパラメータ(装置間でメッセージによる変更通知が不要なパラメータ)が取り得る範囲の広さに応じて、符号化演算アルゴリズムを適応的に選択する符号化部、を備える構成とした。 - 特許庁
To provide a wireless apparatus by optimizing a control voltage for varying a transmission output applied to a drive amplifier and a final amplifier so as to operate the drive amplifier and the final amplifier at an optimum operating point by each transmission output at all times thereby improving a transmission efficiency, saving power and taking a wide variablerange of the transmission output. ドライブアンプとファイナルアンプに供給される送信出力可変用の制御電圧を最適化して、ドライブアンプとファイナルアンプが各送信出力で常に最適動作点で動作するようにすることにより、送信効率の向上を図って省電力化が可能になるとともに、送信出力の可変範囲を広くとることができる無線機を提供すること。 - 特許庁