「rectification」を含む例文一覧(1431)

<前へ 1 2 .... 9 10 11 12 13 14 15 16 17 .... 28 29 次へ>
  • The request for renewal shall be rejected if, even after rectification or comments, it still does not comply with the requirements stated in the invitation.
    更正又は意見の後もなお更新請求が当該求めに記載された要件を満たしていない場合は,更新請求は拒絶される。 - 特許庁
  • The Commissioner must, as soon as practicable, send a copy to the owner of the registered trade mark of an application by another person for rectification.
    局長は,できる限り速やかに,登録商標の所有者に対して,他人による更正申請書の写しを送付しなければならない。 - 特許庁
  • Subject to subsection (2), any person having a sufficient interest may apply for the rectification of an error or omission in the register.
    (2)に従うことを条件として,十分な利害を有する何人も,登録簿における誤り又は脱漏の更正を申請することができる。 - 特許庁
  • If the application does not fulfill these requirements, the Norwegian Competition Authority shall grant a reasonable period of time for rectification.
    当該請求がこれらの要件を遵守していない場合は,ノルウェー競争庁は,不備を更正するための適切な期間を付与するものとする。 - 特許庁
  • A full-wave rectification circuit 1, connected to an external AC power 100 via a resistive element 8, charges a capacitate element 3 for smoothing.
    抵抗素子8を介して外部交流電源100に接続された全波整流回路1は平滑用容量素子3を充電する。 - 特許庁
  • An obtained synchronous rectification function is very sensitive to electric current, while a very small number of parts are being used with little complexity.
    得られた同期整流機能は、複雑さが低い構成で非常に少ない部品を使用しながら電流に対して極めて敏感である。 - 特許庁
  • The CPU 21 determines the load condition of a motor, and performs the synchronous rectification of the first transistor Q1 and the second transistor Q2 when the motor is in a high load condition.
    CPU21は、モータの負荷状態を判定し、モータが、高負荷のときは、第1トランジスタQ1、第2トランジスタQ2を同期整流する。 - 特許庁
  • When current supply is started from the battery 4, FETs Q6-Q8 of a rectification part 51 are turned off to stop output of a power generator 3.
    バッテリ4から電流供給が開始されたならば、整流部51のFETQ6〜Q8をオフにして発電機3の出力を停止する。 - 特許庁
  • There is adopted the immersion nozzle 1 having a rectification projecting part 4 provided on the bottom face 3 on the inside of the immersion nozzle 1, wherein the center in the elongated direction is narrowed.
    浸漬ノズル1の内側底面3に延在方向中央が狭窄された整流突部4を設けた浸漬ノズル1を採用する。 - 特許庁
  • To improve power conversion efficiency by shortening the conduction period of a body diode of a MOSFET for synchronous rectification.
    同期整流用MOSFETのボディダイオードの導通期間を短縮し、導通損失を低減させて電力変換効率を向上させる。 - 特許庁
  • A forced off circuit 50 monitors the switching voltage Vsw and turns the synchronous rectification transistor M2 off forcibly when it exceeds the ground potential.
    強制オフ回路50は、スイッチング電圧Vswをモニタし、接地電位を上回ると同期整流用トランジスタM2を強制的にオフする。 - 特許庁
  • To provide a wire used for a detector element that performs the detection or rectification even in a high frequency range, and stably operates even at high temperature.
    高い周波数領域での検波や整流が可能な、高温でも安定して動作する、検波素子等に応用可能な細線を提供する。 - 特許庁
  • The AC of a transformer T is subjected to full-wave rectification at a diode bridge D1, and is smoothed to be a DC by an electrolytic capacitor C3.
    トランスTからの交流は、ダイオードブリッジD1により全波整流されて電解コンデンサC3により平滑されて直流とされる。 - 特許庁
  • At least either of a pair of the electrode plates 21 has a formed rectification plate 213 standing toward the other electrode plate 21.
    一対の電極板21の少なくともいずれか一方には、他方の電極板21に向かって立設する整流板213が形成されている。 - 特許庁
  • A power source rectifier circuit 1 inputs AC voltage from an AC power source AC and, after full-wave rectification, generates a pulsating voltage and outputs it.
    電源整流回路1は、交流電源ACから交流電圧を入力し、全波整流して脈流電圧を生成し、出力する。 - 特許庁
  • Each microwave field-detecting needle assembly includes one or more rectifier elements capable of detecting microwave field intensity via rectification.
    各マイクロ波場検出ニードルアセンブリは、整流によってマイクロ波場強度を検出することができる1つまたは複数の整流素子を含む。 - 特許庁
  • The number of partitems and production cost can be reduced by making common the inductance of the port 38 and the diodes 34a, 34b for rectification.
    ポート38のインダクタンスと、整流用のダイオード34a,34bを共用することにより、部品点数の削減、コストの削減が達成される。 - 特許庁
  • The half wave rectifier circuit 6 is, for example, a circuit using a diode or the like and performs half-wave rectification to output an AC voltage of 60 Hz.
    半波整流回路6は、たとえばダイオードなどを用いた回路であり、60Hzの交流電圧を半波整流して出力する。 - 特許庁
  • The main rectification circuit 22 is downstream of the relay 5 to rectify an AC voltage from the external power supply 20 before input to the main power circuit 4.
    メイン整流回路22は、リレー5の後段に在り、外部電源20からの交流電圧を整流してメイン電源回路4に入力する。 - 特許庁
  • A rectification section 2 connects an input terminal thereof with terminals 10, 11 of a triac 1 and fully rectifies AC power from an AC power source AC.
    整流部2は、入力端がトライアック1の端子10,11と接続し、交流電源ACからの交流電力を全波整流する。 - 特許庁
  • To stabilize performance of a motor while suppressing a spark discharge by actualizing excellent rectification without reference to the degree of wear of a brush body.
    ブラシ本体の磨耗度合いを問わずに、良好な整流を実現して火花放電を抑制しつつ、モータの性能を安定させることである。 - 特許庁
  • To improve a rectification by a magnetic flux change in an extended part formed at an end of a magnet and to reduce cogging due to a magnetic flux change of the magnet.
    マグネットの端部に形成した延長部における磁束変化により整流を改善し、かつ、マグネットの磁束変化によるコギングを低減する。 - 特許庁
  • The driver circuit 20 reduces the number of segments where the switching transistor M1 and the transistor M2 for the synchronous rectification drive, as they go into a light-load condition.
    ドライバ回路20は、軽負荷状態となるに従い、スイッチングトランジスタM1および同期整流用トランジスタM2の駆動するセグメント数を減少させる。 - 特許庁
  • A rectifier circuit 10 is provided with a smoothing capacitor C and supplies the electric power taken out by means of the unit 111 to a load 121 after rectification.
    整流回路10は、平滑用コンデンサCを備え、受電ユニット111により取り出された電力を整流して負荷121へ供給する。 - 特許庁
  • PWMIC circuit creates RWM output voltage, of which power factor is improved by adjusting direct current voltage rectified by rectification part in way in of pulse width modulation(PWM).
    PWMIC回路部は整流部により整流された直流電圧をパルス幅変調(PWM)方式で変調して力率が改善されたPWM出力電圧を生成する。 - 特許庁
  • The rectification circuits 3a-3d have DC reference potentials and high frequency reference potentials made common by respective grounds 6a-6d.
    整流回路3a〜3dは、それぞれグランド6a〜6dによって直流に対する基準電位と高周波に対する基準電位を共通とする。 - 特許庁
  • The output voltage V_29 of the auxiliary rectification smoothing circuit 29 is applied to a control circuit 4 as a power supply voltage through a control power supply feeder path 30.
    補助整流平滑回路29の出力電圧V_29は電源電圧として制御電源供給路30を介し制御回路4にも印加する。 - 特許庁
  • MALFUNCTION DETECTION/DIAGNOSIS METHOD AND DEVICE FOR SERVO CONTROL SYSTEM, AND AUTOMATIC RECTIFICATION METHOD AND DEVICE THEREFOR
    サーボ制御システムの異常検出・診断方法および自動適正化方法、並びにサーボ制御システムの異常検出・診断装置および自動適正化装置 - 特許庁
  • A third harmonic generator 23 generates a third harmonic selected by determining a level with reference to a DC output voltage Vdc of a rectification circuit 1.
    第三調波発生器23において整流回路1の直流出力電圧Vdcを基準にしてレベル判定して選択した第三調波を得る。 - 特許庁
  • Also, near the pressure sensors 12_a and 12_b a rectification section is prepared to reduce turbulence generated by head wind during movement of vehicles.
    また、圧力センサ12a、12bの近傍には、車両走行時の前方からの風により発生する乱流を低減させる整流部が設けられている。 - 特許庁
  • The microcomputer 6 receives the signal from the rectification circuit 5 at its control port 9 through a smoothing circuit 7, and performs the load control and the like.
    マイクロコンピュ−タ6は、上記整流回路5からの信号を平滑回路7を介して制御用のポート9で受けて、負荷制御等も行っている。 - 特許庁
  • The amount of protrusion of the fine rectification fins 6, 8 from the inner surface of the metal pipe ranges falls in the range of 0.005 to 0.05 mm with the bottom width ranging from 0.005 to 0.05 mm.
    微小整流フィン6、8の金属管内面からの突出量は0.005〜0.05mmであり、底幅は0.005〜0.05mmである。 - 特許庁
  • The full-wave rectification unit 21 rectifies a supply voltage Vac from an alternating-current power source 10 inputted to first and second input terminals s2, t2.
    全波整流部21は、第1及び第2入力端子s2,t2に入力された交流電源10からの電源電圧Vacを整流する。 - 特許庁
  • To achieve size reduction, cost reduction, and conversion efficiency improvement by directly connecting the side of a resonance circuit and the side of a rectification smoothing circuit without using a transformer for separation.
    共振回路側と整流平滑回路側とを分離用トランスを使用することなく直接接続して小型化、コストダウン、変換効率を改善する。 - 特許庁
  • By electrically connecting a gate electrode and the drain electrode of the thin-film transistor, a nonlinear element having a more favorable rectification property can be obtained.
    また、薄膜トランジスタのゲート電極とドレイン電極を電気的に接続することで、さらに整流特性の良い非線形素子を実現することができる。 - 特許庁
  • The anode terminals of the first and second diodes D22, D23 are respectively connected to the first and second input terminals s2, t2 of the full-wave rectification unit 21.
    第1及び第2ダイオードD22,D23の各アノード端子は、それぞれ全波整流部21の第1及び第2入力端子s2,t3に接続されている。 - 特許庁
  • The AC voltage induced to an auxiliary coil L3 of the transformer TR is rectified by an auxiliary coil rectification smoothing section 16, and fed as the power of the control section 15.
    トランスTRの補助コイルL3に誘起される交流電圧は、補助コイル整流平滑部16で整流し制御部15の電源として供給する。 - 特許庁
  • To realize a power generator attached automatic faucet device capable of reducing a manufacturing cost by forming a bearing section in the central part of a rectification member.
    整流部材の中央部に軸受部を形成させることで製造コストの低減が図れることの可能な発電装置付自動水栓装置を実現する。 - 特許庁
  • An operation blocking circuit 22 turns the synchronous rectification element TR2 off when an output voltage from the separate power supply 16 is not higher than a predetermined level at the time of starting, for example.
    起動時などで別電源16の出力電圧が所定値以下の場合に、同期整流素子TR2をオフさせる作動阻止回路22を設ける。 - 特許庁
  • To provide a synchronous rectification DC-DC converter that has a soft start function capable of a smooth start regardless of whether there is an output residual voltage.
    出力残電圧の有無にかかわらずスムーズに起動できるソフトスタート機能を有する同期整流式のDC−DCコンバータを提供する。 - 特許庁
  • When a shunt resistor current I12 increases beyond a threshold value ITH, the switching operation of a transistor Q11 as a synchronous rectification element is started.
    シャント抵抗電流I12がしきい値ITHを超えて上昇すると、同期整流素子であるトランジスタQ11のスイッチング動作が開始される。 - 特許庁
  • Between a rectification circuit 59 and a smoothing circuit 63, there is provided a capacitor 2 of which capacity is larger than that of a capacitor 57 as a parasitic element of a diode 58.
    整流回路59と平滑回路63との間に、ダイオード58の寄生素子であるコンデンサ57の容量よりも容量が大きいコンデンサ2を設ける。 - 特許庁
  • To provide a performance test for an overvoltage protection circuit in a power supply unit using a synchronous rectification element by applying an external voltage to an output terminal.
    同期整流素子を用いた電源装置の過電圧保護回路の動作試験を、出力端子に外部電圧を印加する方法で実現する。 - 特許庁
  • Steam is heated to form superheated steam in a rectification process, and impurity solid granule is removed by filtration by means of superheated steam passing through a microporous membrane.
    精留プロセスで、蒸気を加熱して過熱蒸気を形成し、過熱蒸気が微小孔のある膜を通して不純物固体顆粒を濾過で除去する。 - 特許庁
  • An offset voltage in a reverse direction to an output voltage of the 31m long wiring is produced from the 51m wiring using a rectification circuit 52 and a Zener diode 54.
    整流回路52とツエナーダイオード54を用いて巻線51mから巻線31mの出力電圧と逆向きのオフセット電圧を作る。 - 特許庁
  • After normalization of a level of a reproduced RF signal, a frequency component of recorded data is eliminated, and plus and minus defect are put in the same quadrant by performing full-wave rectification.
    再生RF信号のレベルを正規化後、記録データの周波数成分を除去し、全波整流してプラスとマイナスのディフェクトを同一象限にする。 - 特許庁
  • A switching power supply device 1 relating to the present invention comprises a transformer 3, a switching element 4, a first rectification smoothing circuit 5, and an output voltage generating circuit 6.
    本発明に係るスイッチング電源装置1は、トランス3と、スイッチング素子4と、第1整流平滑化回路5と、出力電圧生成回路6とを備える。 - 特許庁
  • The synchronous rectification parts 15-1, 15-2 rectify synchronously the output signal So from the voltage conversion part 10 respectively by the frequencies f1, f2.
    同期整流部15−1、15−2は、電圧変換部10の出力信号Soをそれぞれ周波数f1またはf2により同期整流する。 - 特許庁
  • It also comprises an auxiliary switch element 14 for driving the rectification switch element 6 and a Zener diode 13 connected to the control terminal of the auxiliary switch element 14.
    整流用スイッチ素子6を駆動する補助スイッチ素子14と、補助スイッチ素子14の制御端子に接続されたツェナーダイオード13とを備える。 - 特許庁
  • The rectification member 51, while the one end engaged with the dented portion 52 is arranged between the metallic support frame 50 and the metallic separator 60b.
    整流部材51は、その一端が、へこみ部52に係合されている状態で、金属製支持フレーム50と金属製セパレータ60bとの間に配置されている。 - 特許庁
<前へ 1 2 .... 9 10 11 12 13 14 15 16 17 .... 28 29 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.
  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.