「rectifier」を含む例文一覧(2043)

<前へ 1 2 .... 25 26 27 28 29 30 31 32 33 .... 40 41 次へ>
  • The output of the first divisional winding 22a is rectified and outputted by a first rectifier 24, and the output of the second divisional winding 22b is rectified and outputted by a second rectidier 25.
    そして、第1分割巻線22aの出力が第1の整流器24により整流されて出力され、第2分割巻線22bの出力が第2の整流器25により整流されて出力される。 - 特許庁
  • To provide a switching power supply device that can reliably reduce reverse voltage applied to a rectifier element connected to a secondary winding of a transformer and minimize increase of loss as a whole device.
    トランスの2次巻線に接続される整流素子に加わる逆方向電圧を確実に低減するとともに、装置全体としての損失の増加も抑えることができるスイッチング電源装置を提供する。 - 特許庁
  • To improve a crest factor of a load current by suppressing, at a zero cross point of an AC power supply, the resonance voltage of a capacitor connected to output terminals of a rectifier to reduce higher harmonics of the input current.
    入力電流高調波の低減のために整流器の出力端に接続されたコンデンサの共振電圧を、交流電源のゼロクロス付近で抑制して、負荷電流の波高率を改善する。 - 特許庁
  • To prevent break of a rectifier element, etc., by reducing the output current of a DC-DC converter when the output impedance of the converter drops due to short-circuiting, etc., in the load of the converter and, in addition, to reduce the power loss in the converter.
    DC−DCコンバータの負荷短絡等による出力インピーダンス低下時の出力電流を低減して整流素子等の破壊を防止すると共に電力損失を低減する。 - 特許庁
  • To obtain a zero-current zero-voltage switching cell that reduces a loss caused by the reverse recovery of a boost rectifier, and at the same time can eliminate the switching loss of main and auxiliary switches.
    ブースト整流器の逆回復に起因する損失を低減するとともに、メインスイッチ及び補助スイッチのスイッチング損失をなくすことができるゼロ電流ゼロ電圧スイッチング型セルを提供する。 - 特許庁
  • A connector 202 connected to a downstream side of a rectifier circuit 212 in a first circuit substrate 210 and a connector 302 connected to upstream side of a power factor improving circuit 310 are connected by wiring 401.
    第1回路基板210の整流回路212の下流側に接続されたコネクタ202と力率改善回路310の上流側に接続されたコネクタ302とを配線401により接続する。 - 特許庁
  • A rectifier 6 for the AC generator for vehicle has a positive-pole side radiator fin and the negative-pole side radiator fin 68 facing each other apart in the axial direction interposing a terminal board 61.
    この車両用交流発電機の整流装置6は、端子台61を挟んで軸方向に離間して対向配置された正極側放熱フィンと負極側放熱フィン68を備えている。 - 特許庁
  • To provide a three-phase rectifier that reduces pulsation of DC voltage and harmonic waves of input current even if a capacitor or a reactor having a small capacity is used.
    容量の小さいコンデンサやリアクトルを使用した場合でも、直流電圧の脈動や入力電流の高調波を低減することが可能な3相整流器を提供することを目的とする。 - 特許庁
  • To provide a rectifier bridge circuit by which, even in the case of a load dump, that is, sudden cut-off of a load, the load dump energy is evenly distributed to all the diodes.
    本発明の課題は、ロードダンプの場合、すなわち負荷の遮断の急に行われる場合にも、ロードダンプエネルギが全てのダイオードに均等に分配される整流器ブリッジ回路を提供することである。 - 特許庁
  • To provide a reliable alternator wherein vibration in a terminal to which an external load is connected is prevented from being transmitted to a semiconductor device attached to the cooling plate of a rectifier instrument.
    外部負荷が接続されるターミナルの振動を整流装置のクーリングプレートに装着される半導体素子へ伝達されるのを阻止して、信頼性の高い交流発電機を提供することにある。 - 特許庁
  • When the voltage of the power generator rises and the voltage of a thyristor rectifier 2 to which power is supplied from the power generator becomes higher than the voltage of the DC power supply 9, the thyristor switches 3a and 3b are turned off.
    発電機の電圧が立ち上がり発電機から電力が供給されるサイリスタ整流器2の電圧が直流電源9の電圧よりも高くなったらサイリスタスイッチ3a,3bをオフにする。 - 特許庁
  • To provide a synchronous rectifier-type converter capable of improving conversion efficiency and preventing the generation of an inverse converting operation (power regeneration).
    本発明は同期整流型コンバータに関し、変換効率を向上させることができ、かつ逆コンバート動作(電力回生)が発生しない同期整流型コンバータを提供することを目的としている。 - 特許庁
  • To provide a quantum dot diode type rectifier that can give the rectifying operation of current within a voltage range by utilizing the phenomenon of Coulomb blockade.
    量子ドット間の単電子トンネリングにおけるクーロンブロッケイド現象を利用することにより、ある電圧範囲内で電流の整流作用を持たせることができる量子ドットダイオード型整流器を提供する。 - 特許庁
  • To provide a control circuit for a three-phase PWM rectifier capable of reducing a DC ripple superposed to a DC output voltage and the variable component of a DC voltage.
    本発明は、直流出力電圧に重畳される直流リップルや直流電圧の変動成分を低減することができる三相PWM整流器の制御回路を提供することにある。 - 特許庁
  • When a control circuit 24 is kept on standby, the Schottky diode 22 handles a reverse current that appears in a synchronous rectifier, so that intrinsic body diode effects of the vertical conduction MOSFET 21 are removed.
    制御回路24の「待機」状態のときに同期型整流装置に見られる逆方向電流をショットキーダイオード22が扱うので、垂直導通MOSFET21の固有ボデーダイオード効果を除去する。 - 特許庁
  • The rectifier cell unit 50 comprises a bypass diode 52 for reverse current prevention being connected with the two corresponding terminal boards 30, respectively, and a metal clip 53 for holding the bypass diode 52 resiliently.
    整流素子ユニット50は、対応する二つの端子板30の夫々に接続される逆流防止用のバイパスダイオード52と、このバイパスダイオード52を弾性的に抱持する金属性のクリップ53とからなる。 - 特許庁
  • A switching power supply includes a primary resonance capacitor connected in parallel to a primary switching element or a primary winding of a transformer and a secondary resonance capacitor connected to a secondary winding or a secondary rectifier diode.
    スイッチング電源装置は、一次スイッチング素子又はトランスの一次巻線と並列に接続された一次共振コンデンサと、二次巻線又は二次整流ダイオードに接続された二次共振コンデンサとを含む。 - 特許庁
  • Therefore, the game ball P is supplied from the rectifier 301 onto the shooting rail 304, whereby the shooting hammer 302 can eject the game ball P and shoot the same to the game area of the game board.
    そのため、整流器301から発射レール304上に遊技球Pが供給されており、発射槌302は当該遊技球Pを弾き出して遊技盤の遊技領域に発射することができる。 - 特許庁
  • To provide a rectifier which is achieved in high-accuracy current balance between parallel power semiconductors without selecting electric characteristics of the parallel-connected power semiconductors, and a rectifying method.
    並列接続された電力半導体の電気的特性を選別することなく、並列電力半導体間の高精度な電流バランスを実現する整流装置および整流方法を提供する。 - 特許庁
  • To provide a compact, reliable motor control device that miniaturizes a rectifier circuit portion and can cope even with both the constitutions using a position sensor and no position sensor.
    整流回路部分を小型化すると共に、位置センサを用いた構成および位置センサレスの構成のいずれの構成でも対応することが可能な小型で信頼性の高いモータ制御装置を提供すること。 - 特許庁
  • A DC voltage outputted from a rectifier circuit 103 is branched by a shunt resistor 106 and the DC voltage value branched by the shunt resistor 106 is converted into digital data by an AD converter 107.
    整流回路103から出力された直流電圧を分圧抵抗106で分枝し、分圧抵抗106で分枝された直流電圧の値をADコンバータ107でデジタルデータにする。 - 特許庁
  • The main operations of the fuel pump 15, fuel injection valve 10, and ignition device 27 are distributed into the half-wave waveforms different from each other among the half-wave waveforms of the power rectified by the rectifier 25.
    燃料ポンプ15、燃料噴射弁10、および点火装置27のそれぞれの主動作は、整流器25で整流された電力の半波波形のうち、互いに異なる半波波形内に配分される。 - 特許庁
  • While using the continuous casting device equipped with the immersion nozzle, and energizing between the rectifier 12b and a molten metal passing through the inner face thereof, the molten metal is supplied into a mold.
    この浸漬ノズルを備える連続鋳造装置を用い、整流部12bとその内部を通過する溶融金属との間に通電しながらタンディッシュ内の溶融金属を鋳型に供給する。 - 特許庁
  • To provide a rectifier in a game machine capable of preventing a ball sending member from erroneously oscillating by an electromagnet, reducing the magnetic attraction force, and smoothly oscillating the ball sending member.
    球送り部材が誤って揺動することを防止し、電磁石による磁気吸引力を小さくでき、円滑に球送り部材を揺動させることができる遊技機における整流器を提供すること。 - 特許庁
  • Inverters 16a and 16b are connected between the output terminals 6a and 6b of the rectifier circuit 6 under a connection state selected among a plurality of connection states by a connection circuit 10 based on a connection designation signal.
    インバータ16a、16bを整流回路6の出力端子6a、6b間に、接続回路10が複数の接続状態のうち接続指示信号によって選択されたものに接続する。 - 特許庁
  • This invention further includes a method of generating an adjusted voltage from first and second supply voltages by two high-side switching transistors and one low-side rectifier device.
    本発明はさらに、2つのハイサイドのスイッチング・トランジスタおよび1つのローサイドの整流デバイスによって、第1の供給電圧および第2の供給電圧から調節された電圧を発生させる方法を含む。 - 特許庁
  • A sound signal from a stereo microphone is converted into a DC signal by a rectifier-filter, and the gains of variable amplifiers 13, 14 are controlled by this DC signal in a control voltage generating circuit 16.
    ステレオマイクから取り出した音声信号を平滑整流器で直流に変換し、この直流信号によりコントロール電圧発生回路16で可変増幅器13,14のゲインを制御する。 - 特許庁
  • In the power unit, a charging circuit 30 for charging a capacitor 2 includes a transformer 32, a rectifier circuit 34, a switching element 36, an inductance coil 38, and a reflux diode 40.
    この電源装置において、コンデンサ12を充電するための充電回路30は、トランス32、整流回路34、スイッチング素子36、インダクタンスコイル38および還流ダイオード40を含んでいる。 - 特許庁
  • To improve the efficiency of operating a light-emitting element and reduce the possibility of flicker, even when a rectifier circuit output is supplied to a drive circuit in pulsating flow waveforms.
    整流回路の出力を脈流波形のまま駆動回路に供給する場合にも、発光素子の使用効率の改善を図ることができ、かつ、ちらつきが発生する可能性を低減すること。 - 特許庁
  • The power unit 2 comprises a simple constant voltage circuit comprising a full wave rectifier 24, a Zener diode 26 and a resistor 27, and contributes to the miniaturization of the whole electric screwdriver unit 1 and the improvement of operability.
    電源装置2は、全波整流器24とツェナーダイオード26と抵抗器27とからなる簡単な定電圧回路からなり、電動ドライバユニット1全体の小型化および操作性向上に寄与する。 - 特許庁
  • The DC-DC converter and the DC-AC inverter are connected in parallel, and one end each is connected to the output end of the rectifier/filter, and the other end each outputs power required for a system.
    DC−DCコンバータ、DC−ACインバータは並列され、一端は共に整流器/フィルタの出力端に接続され、もう一端は、システムが必要とする電源をそれぞれ出力する。 - 特許庁
  • While controlling a motor 39 with a computer 43 through a cable 41, the propeller 37 is rotated with the motor 39 to set up an optional current inside of the water tank 3, and it is made to pass through the rectifier plate 13.
    ケーブル41を介してコンピュータ43でモータ39を制御しつつ、モータ39でプロペラ37を回転させて、水槽3内に任意の水流を起こし、整流板13を通過させる。 - 特許庁
  • A high-frequency transformer 6, which is also used as a common part in the rectifier part and the inverter part, is structured with a plurality of secondary windings, provided for each of an upper arm and one secondary winding, provided in common in the bottom arm.
    高周波トランス6は、順変換部と逆変換部に共通にし、上側のアーム別に設けた複数の二次巻線と、下側のアームに共通に設けた1つの二次巻線をもつ構成とする。 - 特許庁
  • For a PWM rectifier circuit 6, the switching frequency of a PWM rectifying circuit 2 is set to be approximately three times the switching frequency of a PWM inverter 4 by a PWM inverter controller 7.
    PWM整流回路制御部6は、PWM整流回路2のスイッチング周波数を、PWMインバータ制御部7によるPWMインバータ4のスイッチング周波数の3倍に設定している。 - 特許庁
  • To obtain an alternator for vehicle which can reduce the number of parts and improve assembling characteristics by supporting a rectifier and a voltage regulator, using a single support member and then mounting these elements to a bracket.
    この発明は、整流器と電圧調整器とを単一の支持部材で支持させてブラケットに取り付けるようにし、部品点数を削減して、組立性を向上できる車両用交流発電機を得る。 - 特許庁
  • An electronic equipment main body 1 receiving the radio wave by a power receiving antenna 13 converts it into a standby power source by a rectifier 14 to supply electric power to circuits 8, 9, and 10 receiving a power-on signal.
    電気機器本体1では、この電波を受電アンテナ13で受信すると、整流器14により待機電源に変換し、パワーオン信号を受信する回路8,9,10に電力を供給する。 - 特許庁
  • Voltage clamping circuitry 125 may include a rectifier circuit 225 comprising inputs 227 and outputs 229, the inputs 227 being in parallel communication across operational circuitry; an electronic active switching device 205 in parallel communication with the outputs 229 of the rectifier circuit 225; and at least one Zener diode 210 in parallel communication with the electronic active switching device 205.
    電圧クランプ回路構成125は、入力227および出力229を備えた整流器回路225であって、入力227は動作回路構成に渡って並列に連絡する整流器回路225と、整流器回路225の出力229と並列に連絡する電子能動スイッチング素子205と、電子能動スイッチング素子205と並列に連絡する少なくとも1つのツェナー・ダイオード210と、を備えていても良い。 - 特許庁
  • At power running, by limiting an input current I of a power converter CNV, a DC voltage Vd drops in the case that a load over its limitation value is applied to it, and power is supplied from a power diode rectifier REC, and the power diode rectifier REC (equivalent to six phases) and the voltage type self-excited power converter CNV (equivalent to six phases) are operated in parallel.
    力行運転時は、電力変換器CNVの入力電流I_cを制限することにより、その制限値を超える負荷がかかった場合、直流電圧Vdが低下し、電力用ダイオード整流器RECから電力が供給されるようになり、電力用ダイオード整流器REC(6相相当)と前記電圧形自励式電力変換器CNV(6相相当)が並列運転される。 - 特許庁
  • The radiotelephone is composed of an antenna 102 of a transmitting-receiving means having a transmitting-receiving function for radio communications and a function for receiving microwaves for charging it, a branching filter 103 for branching microwaves to a radio circuit 106 and to a rectifier circuit 104, the rectifier circuit 104 for converting an AC power to a DC power, and a chargeable battery 105 charged to use.
    無線通信用の送受信機能と充電用のマイクロ波を受信する機能とをあわせ持つ送受信手段としてのアンテナ102と、無線回路106に対するマイクロ波と整流回路104に対するマイクロ波とを分波する分波器103と、交流電力を直流電力に変換する整流回路104と、充電して使用する充電池105とから構成される。 - 特許庁
  • The coin type vibration motor includes upper and lower cases for forming an inner space, the shaft in the upper and lower cases, a rotor supported on the shaft and including a plurality of wound coils, a weight body and a rectifier substrate, a magnet positioned in the upper case in opposed relation to the rotor and a brush selectively connected to the rectifier substrate and positioned in the lower case.
    本発明は、内部空間を形成する上部及び下部ケースと、前記上部及び下部ケース内のシャフトと、前記シャフトに支持され、複数の巻線コイル、重量体及び整流子基板を含む回転子と、前記回転子に対向し、前記上部ケース内に位置するマグネットと、前記整流子基板と選択的に接続され、前記下部ケース内に位置するブラシとを含むコインタイプ振動モーターに関する。 - 特許庁
  • The inverter controller includes a rectifier circuit for converting a first AC power input from an AC power source 1 into a DC power, which includes a diode bridge 6 and a small-capacity reactor 9 connected to the AC input side or a DC input side of the diode bridge 6, and an inverter 10 for converting the DC power from the rectifier circuit into a second AC power to output the second AC power to the motor.
    ダイオードブリッジ6、及びダイオードブリッジ6の交流入力側又は直流出力側に接続される小容量のリアクトル9を含むと共に、交流電源1から入力された第1交流電力を直流電力に変換する整流回路と、整流回路からの直流電力を第2交流電力に変換して、第2交流電力をモータに出力するインバータ10とを備える。 - 特許庁
  • In the AC-DC converter unit comprising a transformer 11 that receives an AC power and outputs it stepping down the voltage and a rectifier 12 that outputs a DC power by rectifying the AC power reduced by the transformer 11, a connecting room 13 capable of housing a secondary-side bushing 11b of the transformer 11 disposed in series is formed at the center in the width direction in the rectifier 12.
    交流電力を受電し電圧を降圧して出力する変圧器11と、変圧器11により降圧された交流電力を整流して直流電力を出力する整流器12とを備えた交直変換器ユニットにおいて、整流器12内の幅方向中央部に、変圧器11の二次側ブッシング11bが縦に配列されて収納可能な接続室13を設ける。 - 特許庁
  • The AC generator 100 for vehicle includes a rotor 10 which rotates with cooling fans 17 and 18, a stator 4 which is counterposed to the rotor 10, a rectifier 24 which rectifies AC voltage generated from the rotor 4 and generates DC output voltage, a voltage controller 25 which controls the output voltage, and a rear cover 27 which covers the rectifier 24 and the voltage controller 25.
    車両用交流発電機100は、冷却ファン17、18とともに回転する回転子10と、回転子10に対向配置された固定子4と、固定子4から出力される交流電圧を整流して直流の出力電圧を生成する整流装置24と、出力電圧を制御する電圧制御装置25と、整流装置24および電圧制御装置25を覆うリアカバー27とを備える。 - 特許庁
  • Utilizing nonlinear characteristics of a rectifier circuit or demodulator circuit in an IC chip of an RFID 201, non-modulated waves or modulated waves of two or more different frequencies are sent from a reader/writer 101, and the RFID 201 receives the non-modulated waves of two or more frequencies and a reader/writer 101 receives harmonic noises generated in the rectifier circuit or demodulator circuit in the IC chip.
    RFID201のICチップの中の整流回路または復調回路の非線形特性を利用して、リーダライタ101から異なる2つ以上の周波数の無変調波または変調波を送出し、RFID201がこの2つの以上の周波数の無変調波を受けてICチップの中の整流回路または復調回路で発する高調波歪みを、リーダライタ101が受信する。 - 特許庁
  • A standby power supply unit has a first standby power circuit wherein the rippled DC output voltage of a full-wave rectifier circuit 12 is filtered to output a first DC voltage, and a second standby power supply circuit having a transistor 7 wherein applying to its collector the rippled DC output voltage of a bridge rectifier circuit 3, its base is grounded via a Zener diode 9 to output a second DC voltage from its emitter.
    ブリッジ整流回路3の脈動直流出力電圧を平滑にした第1の直流電圧を出力する第1のスタンバイ電源回路と、コレクタに上記ブリッジ整流回路の脈動直流出力電圧が印加され、ベースがツェナーダイオード9を介して接地され、コレクタから第2の直流電圧を出力するトランジスタ7を有する第2のスタンバイ電源回路とを備えた。 - 特許庁
  • A driving circuit of MOSFETs of a MOS rectification device driven electric motor is constituted of a rectifier input/output voltage taking-in part, an on-off decision circuit part, an on-off determination logical circuit part, an output buffer part, a diagnostic part, and so on.
    MOS整流型電動機のMOSFETの駆動回路を整流器入出力電圧取り込み部,オンオフ判定回路部,オンオフ決定論理回路部,出力バッファ部,診断部、その他で構成する。 - 特許庁
  • The connectors 1, 2, 4 to (n) supply the received transmission wave to the power supply stabilizing device 70 via rectifier circuits 21, 22, 24 to 2n after canceling the effect, upon processing, exerted by the transmission wave received by the connector 3.
    コネクタ1,2,4〜nは、受信した伝送波を、コネクタ3によって受信された伝送波の処理に与える影響を除去して、整流回路21,22,24〜2nを介して電源安定装置70へ供給する。 - 特許庁
  • Since liquid oxygen with predetermined purity can be contained in the storage tank 20 even after the interruption of the plant, article liquid oxygen can be collected before installing the rectifier tower to shorten starting time upon starting of the plant.
    プラント停止後においても貯槽20内では所定純度の液体酸素を保有できるため、プラント起動時は、精留塔が整定する前に製品液体酸素を採取でき、起動時間を短縮することが可能となる。 - 特許庁
  • Four diodes D1 to D4 for constituting a rectifier DB, a drive transformer CT, switching elements Q1, Q2, and a leakage transformer T2 of a load circuit 1 are sequentially arranged in this order in a lengthwise direction on a printed board 30.
    プリント基板30は、長手方向に沿って、整流回路DBを構成する4個のダイオードD1〜D4、駆動トランスCTと各スイッチング素子Q1,Q2、負荷回路1のリーケージトランスT2の順に配設してある。 - 特許庁
  • To obtain a controller of electric equipment capable of forming a discharge path by which a capacitor charge in a voltage doubler rectifier circuit is discharged to a load when the input from an AC power supply goes off, and to obtain a refrigerator equipped with the controller of the electric equipment.
    交流電源からの入力がなくなった場合、倍電圧整流回路のコンデンサーの電荷を、負荷へ放電させる放電経路を形成することができる電気機器の制御装置及び冷蔵庫を得る。 - 特許庁
<前へ 1 2 .... 25 26 27 28 29 30 31 32 33 .... 40 41 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.