「rectifying diode」を含む例文一覧(232)

<前へ 1 2 3 4 5 次へ>
  • The sum of backward direction conducting voltages of the Zener diodes ZD1, ZD2 and ZD3 is set to a value smaller than the backward direction conducting voltage of the rectifying junction diode 71, and the sum of forward direction threshold voltages is set to a value larger than the forward direction threshold voltage of the rectifying junction diode 71.
    ツェナーダイオードZD1、ZD2、ZD3の逆方向導通電圧の合計は整流用接合ダイオード71のそれよりも低く、順方向しきい値電圧の合計は整流用接合ダイオード71のそれより大きい設定される。 - 特許庁
  • Rectifying diode (V2) and resistor are connected in parallel with PIN diode (V1) to rectify RF signals and generate a D.C. voltage across the resistor which biases PIN diode to its conductive state.
    整流ダイオード(V_2)及び抵抗は、RF信号を整流して、PINダイオードにバイアスをかけて導通状態にする抵抗にDC電圧を発生させるように、PINダイオード(V__1)と並列に接続されている。 - 特許庁
  • For a circuit for improving the power factor, a normal-mode noise filter is inserted to a commercial AC power line, and a bridge rectifying circuit formed of a rectifying diode of a high-speed recovery type is connected thereto, to allow an equimultiple-voltage rectifying operation to be operated.
    また、力率改善のための回路としては、商用交流電源ラインにノーマルモードノイズフィルタを挿入すると共に、高速リカバリ型の整流ダイオードによるブリッジ整流回路を接続することで等倍電圧整流動作とする。 - 特許庁
  • This device comprises an antenna circuit 10 receiving high frequency signal, a rectifying circuit 20 rectifying the high frequency signal received by the antenna circuit 10, and a lighting circuit 30 lighting a light emitting diode 33 by a voltage obtained by rectifying the high frequency signal by the rectifying circuit 20.
    高周波信号を受信するアンテナ回路10と、このアンテナ回路10が受信した高周波信号を整流する整流回路20と、この整流回路20により上記高周波信号を整流して得られる電圧によって発光ダイオード33を点灯させる点灯回路30とからなる - 特許庁
  • To provide a circuit which can prevent an electromagnetic conduction interference from a feedback signal by increasing the linear function of a rectifying diode.
    整流ダイオードの線的機能を増進し、帰還信号からの電磁導電干渉を防止可能である回路を提供する。 - 特許庁
  • A full-wave rectifying circuit 22 is provided on the input side of the diode bridge 4, to input the rectified output into the control IC 18.
    ダイオードブリッジ4の入力側に全波整流回路22が設けられ、その整流出力を制御用IC18に入力する。 - 特許庁
  • Thus, the peak level of rectification current that flows the rectifying diode is further reduced than in the case of double voltage half-wave rectification circuit.
    これにより、整流ダイオードを流れる整流電流のピークレベルは、倍電圧半波整流回路の場合よりも低減される。 - 特許庁
  • To provide a switching power device in which a surge voltage to be generated in a reverse direction to an output rectifying diode is suppressed.
    出力整流ダイオードに対して逆方向に発生するサージ電圧が抑圧されたスイッチング電源装置を提供する。 - 特許庁
  • A combined semiconductor rectifying device 1 is configured such that a PN-type silicon diode 1b and a Schottky barrier diode 1a of a semiconductor, whose breakdown voltage is higher than that of silicon and whose band gap is wider than that of the silicon, are connected in series.
    PN型シリコンダイオード1bとシリコンよりも高耐圧でワイドバンドギャップな半導体のショットキーバリアダイオード1aを直列接続した複合半導体整流素子1とする。 - 特許庁
  • Also, by connecting a secondary side parallel resonance capacitor C2, in parallel with a secondary side rectification diode, radiation noise generated at the inverse recovery time of a rectifying diode is absorbed.
    また、二次側並列共振コンデンサC2を二次側の整流ダイオードに対して並列に接続することで、整流ダイオードの逆回復時間時に発生する輻射ノイズを吸収する。 - 特許庁
  • A power supply unit (1) includes a diode bridge (11) for rectifying AC voltage from an AC power supply (E1) and a smoothing capacitor (13) for smoothing DC voltage from the diode bridge (11).
    電源装置(1)は、交流電源(E1)からの交流電圧を整流するダイオードブリッジ(11)と、当該ダイオードブリッジ(11)からの直流電圧を平滑する平滑コンデンサ(13)とを備えている。 - 特許庁
  • Similarly, the sum of backward direction conducting voltages of the Zener diodes ZD4, ZD5 and ZD6 is set to a value smaller than the backward direction conducting voltage of the rectifying junction diode 72, and the sum of forward direction threshold voltages is set to a value larger than the forward direction threshold voltage of the rectifying junction diode 72.
    同じく、ツェナーダイオードZD4、ZD5、ZD6の逆方向導通電圧の合計は整流用接合ダイオード72のそれよりも低く、順方向しきい値電圧の合計は整流用接合ダイオード72のそれより大きい設定される。 - 特許庁
  • This device has a rectifying characteristic which is equivalent to that of an ordinary semiconductor p-n junction, and exhibits the function of a diode or a transistor.
    本デバイスは、通常の半導体pn接合と同等の整流特性を有しダイオード若しくはトランジスタとしての機能を発揮する。 - 特許庁
  • Finally, the upper and lower printed circuit boards are provided opposed with each other to complete electrical coupling between the rectifying circuit and light emitting diode circuit using bumps.
    最後に再び上下プリント基板を相対させバンプで整流回路と発光ダイオード回路の間の電気連結を完了させる。 - 特許庁
  • A power supply device includes a rectifier diode 2 for rectifying a dc voltage which is converted into a predetermined dc voltage by a power factor improving circuit 3.
    整流ダイオード2で整流された直流電圧は、力率改善回路3にて所定の直流電圧へ変換される。 - 特許庁
  • The power supply 1 is provided with a conversion circuit 5 as a half-wave rectifying circuit, comprising one diode and a class-E amplifying circuit 7.
    電源装置1は、一つのダイオードで構成さる半波整流回路である変換回路5と、E級増幅回路7と、を備える。 - 特許庁
  • The rectifying element is the p-i-n diode comprising a p-type semiconductor layer, an n-type semiconductor layer, and an intrinsic semiconductor layer between them.
    整流素子は、p型半導体層、n型半導体層及びこれらの間の真性半導体層から構成されるp-i-nダイオードである。 - 特許庁
  • A rectifying diode 7 is connected to a conductive wire 22, connected to an auxiliary electrode 3 with the cathode on an auxiliary electrode 3 side.
    補助電極3に接続された導電線22に、カソードを補助電極3側として整流用のダイオード7を接続している。 - 特許庁
  • An electromagnetic wave-electricity conversion circuit 20 constituting the electromagnetic wave utilization system comprises a conversion element 21 which generates a current in an electromagnetic wave atmosphere, a rectifying diode 22 connected in series with the conversion element 21, and a capacitor 23 connected with the conversion element 21 through the rectifying diode 22.
    電磁波利用システムを構成する電磁波−電気変換回路20は、電磁波雰囲気中で電流を発生させる変換素子21と、同変換素子21に直列接続された整流用ダイオード22と、整流用ダイオード22を介して変換素子21に接続されたコンデンサー23とを備える。 - 特許庁
  • A path leading to a switch element SW from an output rectifying diode D1 of a boosting chopper is provided with an inductance L2 for current control, to control the recovery current to an output rectifying diode D1 in a transient period, when the switching element SW is shifted from on to off.
    昇圧チョッパの出力整流ダイオードD1からスイッチング素子SWに至る経路に、スイッチング素子SWがオンからオフに移行する過渡期間に出力整流ダイオードD1に流れるリガバリ電流を抑制するリカバリ電流抑制用インダクタンスL2を設ける。 - 特許庁
  • An additional high-voltage rectifying diode device DHV6 is provided in series with a rectifying current path of a multi-stage rectifying circuit for generating the DC high voltage, thereby attaining a high frequency of a ringing current, caused by the structure of a flyback transformer FBT.
    さらに直流高電圧を生成するための多段型整流回路の整流電流経路に対して、直列に追加高圧整流ダイオード素子DHV6を直列に設けるようにして、フライバックトランスFBTの構造に起因して生じるリンギング電流の高周波化を図る。 - 特許庁
  • The AC/DC converter 20 includes a noise filter 121, a DC/DC converter 123, a rectifying circuit 122 connected to the other end of the triac T, a diode D provided between the rectifying circuit 122 and the noise filter 121, and a constant-current circuit 24 provided at a poststage of the rectifying circuit 122.
    AC/DCコンバータ20は、ノイズフィルタ121と、DC/DCコンバータ123と、トライアックTの他端に接続された整流回路122と、整流回路122とノイズフィルタ121との間に設けられたダイオードDと、整流回路122の後段に設けられた定電流回路24と、を備える。 - 特許庁
  • This device comprises a double voltage rectifying circuit (5) which is composed of a capacitor (c) and a diode (D), and frequency control circuits (3, 6, and 7) which control the frequency (Fr) inputted into the double voltage rectifying circuit (5) so as to keep the output voltage (Vo) of the double voltage rectifying circuit (5) constant.
    コンデンサ(C)とダイオード(D)で構成される倍電圧整流回路(5)と、倍電圧整流回路(5)の出力電圧(Vo)を一定に維持するために倍電圧整流回路(5)に入力する交流電圧の周波数(Fr)を制御する周波数制御回路(3,6,7)とを具備する。 - 特許庁
  • The semiconductor device 10 comprises an active element part, i.e., an SIThy 12, a rectifying section, i.e., a diode 14, and an isolation layer 16 for insulating the SIThy 12 from the diode 14.
    能動素子部であるSIThy12と、整流部であるダイオード14と、前記SIThy12とダイオード14とを電気的に絶縁する分離層16から半導体装置10を構成する。 - 特許庁
  • There is provided fin temperature control means for controlling a temperature of a cooling fin such that a temperature of the cooling fin mounted with a diode changes in inverse proportion to an output current value of a diode rectifying circuit.
    ダイオードを搭載した冷却フィンの温度が、ダイオード整流回路の出力電流値に反比例して変化するように、冷却フィンの温度を制御するためのフィン温度制御手段を備える。 - 特許庁
  • Since the second auxiliary diode 46 is present, discharge current (a discharge current i42) of the auxiliary capacitor 42 flows via the rectifying power source 10.
    第二補助ダイオード46があるために、補助コンデンサ42の放電電流(放電電流i42)が整流電源10を経由して流れる。 - 特許庁
  • To protect a diode in a housing from high operating temperature of a rectifier in a rectifying device for three-phase power generator for a vehicle.
    自動車用の三相発電機用の整流デバイスにおいて、整流器の高い動作温度から、ハウジング内のダイオードをより良好に保護する。 - 特許庁
  • A diode bridge DB, which is a full-wave rectifier for full-wave rectifying an alternator Vs, is connected between main terminals of a TRIAC TRC.
    トライアックTRCの主端子間には交流電源Vsを全波整流する全波整流器たるダイオードブリッジDBが接続される。 - 特許庁
  • Then the power source circuit outputs an alternating current generated in a secondary winding Ns of the transformer T1 to a main capacitor Cm of a stroboscope circuit, after rectifying the current by means of a diode D1.
    そして、トランスT1の二次巻線Nsに発生した交流をダイオードD1により整流し、ストロボ回路のメインコンデンサCmに出力する。 - 特許庁
  • To provide a DC converter which can achieve higher efficiency and downsizing by reducing the loss of power and reducing the breakdown strength of the secondary rectifying diode of a transformer.
    電力の損失を低減し、トランスの2次側の整流ダイオードの耐圧を低減させ、高効率化及び小型化を図れる直流変換装置。 - 特許庁
  • A coil driving power supply of the relay K1 is supplied by half-rectifying a line voltage of the alternating-current power supply from the plug J1 through a diode D7.
    リレーK1のコイル駆動電源はプラグJ1からダイオードD7を介して交流電源のライン電圧を半波整流して供給される。 - 特許庁
  • An induction current flowing in an overhead ground wire 11 is detected by a current transformer 12, rectified by a rectifying diode 14, and charged to an accumulator battery 15.
    架空地線11を流れる誘導電流が変流器12で検出され、整流用ダイオード14で整流されて、蓄電池15に充電される。 - 特許庁
  • To prevent thermal destruction in an audio amplifier when a rectifying diode used in a power supply circuit exceeds an upper limit temperature before a power amplifier does.
    オーディオアンプにおいて、電力供給回路に使用される整流ダイオードがパワーアンプより先に上限温度を超えた場合の熱破壊を防止する。 - 特許庁
  • Specifically, if the rectifying units are made of a Schottky diode, the voltage drop can be significantly reduced compared with other types of diodes.
    特に、整流部30A〜30Fをショットキーダイオードにより構成すれば、他の種類のダイオードに比べて電圧降下を著しく小さくすることができる。 - 特許庁
  • The sub-transformer 170 includes primary coils (conductors 181 and 185), a secondary coil (conductor 183), and a rectifying and smoothing circuit (diode D9 and capacitor C5).
    サブトランス170は、1次コイル(導線181および185)と、2次コイル(導線183)と、整流平滑回路(ダイオードD9およびコンデンサC5)とを含む。 - 特許庁
  • The power tool 1 further includes a switching element 93 for driving the brushless motor 3, and a diode bridge 95 for rectifying current from the power cable 25.
    電動工具1は、さらにブラシレスモータ3を駆動するためのスイッチング素子93と、電源コード25からの電流を整流するダイオードブリッジ95とを備える。 - 特許庁
  • This rectifying device enables the use of a diode chip which does not have a housing not surrounded with a synthetic resin as the protection material.
    本発明による整流デバイスは、保護材としての合成レジンで包囲されないようなハウジングを有しないダイオードチップの使用を可能にするものである。 - 特許庁
  • For a circuit for improving the power factor, a normal-mode noise filter is inserted to a commercial AC power line, and a bridge rectifying circuit formed of a high-speed recovery diode is connected thereto, to allow an equimultiple-voltage rectifying operation to be performed.
    また、力率改善のための回路としては、商用交流電源ラインにノーマルモードノイズフィルタを挿入すると共に、高速リカバリ型の整流ダイオードによるブリッジ整流回路を接続することで等倍電圧整流動作とする。 - 特許庁
  • A diode D6 and a smoothing capacitor C4 that are sub-rectifying circuits are arranged that feed the power necessary for starting the control circuit 12 to the power supply terminal VCC by rectifying an AC on the basis of the AC input.
    制御回路12の動作時に必要な電力を、上記交流入力に基づく交流の整流により電源端子VCCに供給する副整流回路であるダイオードD6および平滑用コンデンサC4を設ける。 - 特許庁
  • Then, by detecting the discontinuity of the current flowing to the smoothing choke coil at the time of the light load, and feeding the detected control signals to gate electrodes of the synchronous rectifying field effect transistors 34, 35, the synchronous rectifying field effect transistors 24, 25 are made non-conductive, thus switching the synchronous rectifying operation during that time to a synchronous rectifying operation conducted by a contained diode.
    そして、軽負荷時に平滑チョークコイルに流れる電流の不連続性を検出してこの検出した制御信号を上記同期整流制御用電界効果トランジスタ34、35のゲート電極に供給することにより、同期整流用電界効果トランジスタ24,25を非導通として、その間の同期整流動作を内蔵ダイオードによる同期整流動作に切り換える。 - 特許庁
  • The flexible printed circuit board 10, where the coil 10 is formed and the rectifying diode 14 and the light-emitting diode 15 are placed, is inserted into an inside of a tip point of an antenna of a communication apparatus or equipped at an external of it.
    コイル11が形成され、整流用ダイオード14および発光ダイオード15が配置されたフレキシブルプリント基板10は、通信機器のアンテナ先端部の内部に挿入されるか、外部に装着される。 - 特許庁
  • Thus, since the voltage applied on the diode D1, which is a rectifying element, becomes large, loss due to the diode D1 is reduced, and the RF/DC conversion efficiency of the double-voltage rectifier circuit 1 as a whole is improved.
    このように、整流素子であるダイオードD1にかかる電圧が大きくなることで、ダイオードD1による損失が低減され、倍電圧整流回路1全体のRF/DC変換効率が向上する。 - 特許庁
  • A positive diode 81 and a negative diode 82 constituting rectifying elements of a rectifier device 8 of the vehicle-use tandem rotary electric machine dissipate heat to a stator core 33 of a second rotary electric machine 3 acting as a heat sink through a housing 13.
    車両用タンデム式回転電機の整流装置8の整流素子をなす+ダイオード81及び−ダイオード82はハウジング13を通じて、ヒートシンクとしての第2回転電機部3のステータコア33に放熱する。 - 特許庁
  • A constant power output circuit 30 comprising a transformer T1, a switch element S2, a control circuit 12, a rectifying diode D2, a diode D3, a choke coil L2 and a smoothing capacitor C3 supplies constant power to a lamp 60.
    定電力出力回路30は、トランスT1、スイッチ素子S2、制御回路12、整流ダイオードD2、ダイオードD3、チョークコイルL2、平滑コンデンサC3で構成され、ランプ60に定電力を供給する。 - 特許庁
  • Furthermore, the connection terminal of a bridge diode is substantially formed at right angles and is mounted in parallel with the rectifying circuit board, and a heat dissipating plate for the diode bridge is fixed to the base of the housing.
    また、ブリッジダイオードの接続端子が略直角にフォーミングされて整流回路基板と平行に実装され、そのブリッジダイオードに対して放熱板が取り付けられ、その放熱板を筐体の底面に取り付ける。 - 特許庁
  • Then, a transistor 20 switches the conduction state between the plurality of secondary winding 19b and 19c and a conversion circuit (a circuit composed of a rectifying diode 8a for high voltage, a rectifying diode 8b for low voltage, and a capacitor 11), according to an external control signal inputted into a winding-switching control terminal 22a.
    そして、トランジスタ20が、複数の二次巻き線19b及び19cと変換回路(高電圧用整流ダイオード8a、低電圧用整流ダイオード8b、及びコンデンサ11によって構成される回路)との導通状態を、巻き線切替制御ターミナル22aに入力される外部制御信号に応じて切り替える。 - 特許庁
  • In the half-wave rectifying means B2, a first diode D71 is arranged between a single AC pole and a DC positive pole, a second diode D72 is arranged between the single AC pole and a DC negative pole, and the pulse oscillating circuit IC71 is connected between the DC positive pole and the DC negative pole of the half-wave rectifying means B2.
    この半波整流手段B2は、単一交流極と直流正極の間に第1ダイオードD71を配置し、単一交流極と直流負極の間に第2ダイオードD72を配置して、この半波整流手段B2の直流正極と直流負極の間にパルス発振回路IC71を接続する。 - 特許庁
  • The power supply device includes a diode bridge for rectifying an AC voltage supplied from a primary-side AC power supply, a power supply transformer for supplying the voltage, subjected to full-wave rectification by the diode bridge, to a secondary side, and a diode/a capacitor for smoothing the voltage from the power supply transformer.
    1次側の交流電源から供給される交流電圧を整流するダイオードブリッジと、ダイオードブリッジによって全波整流された電圧を2次側へ供給するための電源トランスと、電源トランスからの電圧を平滑するダイオード及びコンデンサを備えたことを特徴とする。 - 特許庁
  • To provide a power supply circuit capable of suppressing the generation of a surge voltage in a rectifying diode, with respect to a full-wave rectifying circuit formed by assembling two diodes, using a transformer provided with a center tap to a secondary winding.
    二次巻線にセンタータップが設けられたトランスを用い、2つのダイオードを組み合わせることにより形成された全波整流回路について、整流ダイオードにサージ電圧が発生することを抑えることができる電源回路を提供する。 - 特許庁
  • By mounting a diode D5 on the input side of the secondary-side rectifying circuit 3, a current from a coil L1 of the secondary-side smoothing circuit 4 is supplied to a lamp 5 through the diode D5 while the switching element Z5 is at the OFF state.
    また、2次側の平滑回路3の入力側にダイオードD5を設けることで、スイッチング素子Z5をOFFしている間、2次側の平滑回路4のコイルL1からの電流がダイオードD5を介してランプ5に供給される。 - 特許庁
<前へ 1 2 3 4 5 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.