In reception of an information signal, a reference point K1 which is temperature of a tire included in the signal and at which air pressure becomes a minimum low air pressure threshold Th1 is set. 情報信号の受信時に、その信号に含まれるタイヤの温度であって空気圧が最小低空気圧閾値Th1となる基準点K1を設定する。 - 特許庁
A heater is clamped to the nozzle by using a screw, so that the amount of heat transferred to the nozzle can be confined within an optimum range without reference to the temperature of the heater. ヒーターをノズルにクランプ止めするのにねじを使用することによって、ノズルに伝達される熱の量をヒーターの温度に拘わらず最適範囲内にとどめる。 - 特許庁
The cetane value of the fuel is determined in reference to a predetermined map on the basis of the time TSTART necessary for starting and the cooling water temperature Tw in starting. そして、始動に要した時間TSTARTと、始動時の冷却水温度Twとから、予め定めたマップを参照して、燃料のセタン価を判定する(S8)。 - 特許庁
To perform low power supply voltage operation ≤1 V and low current operation not more than dozens of nA, and to obtain a reference voltage not depending on a temperature with a small circuit scale. 1V以下の低電源電圧動作、及び数10nA以下の低電流動作をし、かつ温度に依存しない基準電圧を、小さな回路規模で得ることにある。 - 特許庁
Further, with a reference circuit including a bipolar transistor, temperature dependence of the drive transistor which supplies current to light emitting elements of pixels and drives them is compensated. さらに、バイポーラトランジスタを有するリファレンス回路を有することにより、画素の発光素子に電流を供給して駆動する駆動トランジスタの温度依存性を補償する。 - 特許庁
To provide a thermopile-type infrared sensor capable of reducing the effects of infrared rays to cold contacts (theoretical reference points) in a thermopile and accurately measuring temperature. 熱電堆における冷接点(原理的基準点)の赤外線の影響を低減し、より正確に温度計測ができるサーモパイル型赤外線センサを提供する。 - 特許庁
A third current supply side (M3) of the current mirror circuit is connected to the collector of the Q1, and the temperature dependency of the reference voltage is corrected by currents I_2 acquired in the M3. カレントミラー回路の第3電流供給側(M3)は、Q1のコレクタに接続され、M3に得られる電流I_2により、基準電圧の温度依存性を補正する。 - 特許庁
In the reference cell 2, characteristics are deviated so as to following deviation of these characteristics when characteristics of the non-volatile memory cell MC00-MC12 are deviated by influence of temperature variation or the like. リファレンスセル2は、温度変化などの影響で不揮発性メモリセルMC00〜MC12の特性がずれたときに、この特性のずれに追従するように特性がずれる。 - 特許庁
To provide a current correction circuit for a current source circuit, capable of reducing a circuit area and generating a reference current stable against temperature change and process variation. 回路面積を削減し、かつ温度変化及びプロセスバラツキに対して安定な基準電流を生成できる、電流源回路のための電流補正回路を提供する。 - 特許庁
To make surely detectable the temperature distribution of a region to be detected by eliminating detection errors caused by the difference in structure between a heat detection element and a reference element. 熱検知素子とリファレンス素子との構造の違いによる検出誤差を解消して検出対象領域の温度分布を確実に検出できるようにする。 - 特許庁
To provide an exhaust gas purification catalyst system capable of enhancing exhaust gas purifying performance at low temperature directly after an engine is started, and of sufficiently coping with a ULEV reference. エンジン始動直後等の低温時における排気ガス浄化性能を高め、ULEV基準にも十分に対応できる排気ガス浄化触媒システムを提供する。 - 特許庁
After that, a time measuring part 40 measures time until a potential of capacitor C reaches a predetermined reference voltage Vref (time for changing by a temperature of thermistor) as measured data. その後、計時部40により、コンデンサCの電位が所定の基準電圧Vrefになるまでの時間(サーミスタの温度により変化する時間)を、計測データとして測定する。 - 特許庁
The reference voltage of the node N1 in the temperature detection part 19 is adjusted according to the duty ratio of the pulse signal outputted by the pulse signal generation circuit 410. 温度検出部19におけるノードN1の基準電圧は、パルス信号生成回路400により出力されるパルス信号のデューティ比により調整することができる。 - 特許庁
W1 is the total quantity of infiltration amount of heat and the Joule loss in a reference current lead formed of material A in the range from the cryogenic side to the normal temperature side. 極低温側から常温側までを材料Aで形成した基準電流リードにおける熱侵入量とジュール損との合計熱量をW1とする。 - 特許庁
A stopping part 52a stops a CPU 41 if receiving a temperature abnormality signal under the situation where each CPU performs the same process on a clock signal of a reference frequency. 停止部52aは、各CPUが基準周波数のクロック信号で同一の処理をしている状況下で温度異常信号を受け付けると、CPU41を停止する。 - 特許庁
To provide a bandgap reference circuit that reduces variations in a manufacturing process and supplies a constant voltage independent of supply voltage and temperature change. 製造プロセスでのばらつきの影響が抑えられ、なおかつ、電源電圧、温度の変動に依存しない定電圧を供給できるバンドギャップリファレンス回路を提供する。 - 特許庁
When the switch A1 is turned on, the transistors 1, 2a are turned on, the transistor 2b is turned off; and a reference voltage Vrefa having a first temperature coefficient is output. スイッチA1がオンしているとき、トランジスタ1及び2aがオンしかつトランジスタ2bがオフし、第1の温度係数を有する基準電圧Vrefaが出力される。 - 特許庁
To obtain a reference voltage generation circuit and a semiconductor storage apparatus using the same which are capable of performing a sufficient burn-in test in a whole temperature range of acceleration test. 加速試験の全温度範囲において十分なバーンインテストを実施することができる参照電圧発生回路およびそれを用いた半導体記憶装置を実現する。 - 特許庁
To provide a capturing laser beam tracking error detecting method and a device having no characteristic variation caused by a difference in the optical path length and a temperature of reference laser beams from plural light sources. 複数の光源からの参照レーザビームの光路長や温度の差により生ずる特性変動がない補捉レーザビーム追尾誤差検出方法および装置を提供する。 - 特許庁
When the environmental temperature is a reference or higher, the image forming apparatus is made to approximate the fixing paper conveying passage on the paper feed tray bringing warm keeping action not to position loading paper. で、環境温度が基準以上の場合に、保温作用をもたらす給紙トレイにおいて定着用紙搬送経路に近接して積載用紙が位置しないようにする。 - 特許庁
A reference signal S2 is superimposed on a video signal S1 to generate setting data to correct the white balance of the video signal S1 and a color temperature data memory 13 stores the generated data. 映像信号S1に基準信号S2を重畳し、映像信号S1の白バランスを補正するための設定データを生成し、色温度データメモリ13に記憶させる。 - 特許庁
The step for determining the average component includes a step for regulating the drive current until the laser output power becomes substantially equal to a reference signal which varies depending on the temperature. 平均成分を求めるステップは、レーザの出力パワーが、温度に従って変化する基準信号にほぼ等しくなるまで駆動電流を調整するステップを含む。 - 特許庁
A bias line 11 of an integration circuit 7 is subjected to common connection, and a reference signal to be changed according to fluctuation in element temperature or power supply voltage is input in the bias line 11. 積分回路7のバイアス線11を共通接続し、バイアス線11に素子温度変動と電源変動に応じて変化する参照信号を入力する。 - 特許庁
To prevent a specifying time from becoming longer even when a temperature of delay elements, etc., is changed when the number of elements with a phase difference of 360 degrees is specified in order to generate a reference clock. 参照クロックの生成のために、360度の位相差の素子数が特定される際に、遅延素子の温度等が変化しても、特定時間が長くならないこと。 - 特許庁
Resistance values of the unused support structure and the monitored support structure can be converted based on a reference temperature so as to simplify calculation and monitoring of the support structure. 未使用支持構造および監視支持構造の抵抗値は、計算および支持構造の監視を簡略化するため、基準温度に揃えて変換されることができる。 - 特許庁
To provide a reference voltage generating circuit using a low Vt transistor, or the like in which variation in a delay time caused by variation in processes and variation in temperature can be reduced. 低Vtトランジスタを用いた回路において、プロセスばらつきや温度変動に起因する遅延時間のばらつきを低減可能な基準電圧発生回路等を提供する。 - 特許庁
A control means 81 sets the reference temperature T3 to a value corresponding to a degree of the refrigerant leakage in the expansion valve 52 on the basis of the detecting result of the high-low pressure difference detecting means 93 and 97. 制御手段(81)は、高低圧差検出手段(93,97)の検出結果に基づき、膨張弁(52)での冷媒漏れの程度に対応した値に基準温度(T3)を設定する。 - 特許庁
A heat conducting route becomes long because a region where the internal flaw is present has high heat insulating properties and the temperature rising speeds of the crown surface 10 are different between a defective article and a reference article. 内部欠陥が存在する部位は断熱性が高いため伝熱経路が長くなり、欠陥品と基準品とで冠面10の昇温速度が異なる。 - 特許庁
After a heater is turned on (step S501) in response to a print request, waiting is carried out until the reference temperature at which the motor can begin to be driven is reached is detected (step S502). プリント要求に従い、ヒータをONした後(ステップS501)、モータ駆動開始可能な基準温度に到達しているかを検出するまで待つ(ステップS502)。 - 特許庁
To provide a cooker which reduces temperature holding time while clarifying the setting reference and which a user can confidently use consciously of saving electric power consumption. 温度保持時間を短縮しつつも、その設定基準を明確にし、使用者が消費電力量の抑制を意識しながら安心して使用できる加熱調理器を提供する。 - 特許庁
Inherent products of plural sorts sorted in accordance with an environmental temperature to be applied and the existence/non-existence of flow rate control are arranged under an electromagnetic valve A to be a reference product. 基準製品である電磁弁Aの配下には適用する環境温度と流量調節の有無とによって分類される複数種の固有製品がある。 - 特許庁
When the time difference changes and a vehicle nonexistent state (Ta≈Tb) is realized, it is determined that the time difference is changed by influence of an air temperature, and a reference time difference is remeasured. 時間差が変化し、且つ、物体が存在しない状態(Ta≒Tb)となった場合、気温の影響で時間差が変化したと判断し、基準時間差を再測定する。 - 特許庁
Then, based on the temperature signal and the humidity signal in the low/ humidity measurement mode, approximate conversion relative humidity (HUM2') in the reference resistance value and in low-humidity measurement mode is obtained. つぎに、低湿度測定モードでの温度信号および湿度信号に基づき、基準抵抗値でかつ低湿度測定モードでの近似換算相対湿度(HUM2‘)を求める。 - 特許庁
To provide an accurate reference voltage generation circuit allowed to be used also for an A/D converter with the large number of bits and capable of reducing a change in output voltage due to a temperature change. 高ビット数のA/Dコンバータにも利用可能な、温度変化による出力電圧の変化の少ない精密な基準電圧発生回路を提供する。 - 特許庁
To provide an aligner equipped with a position detector capable of measuring the stage position accurately even if a part supporting a reference mirror is moved owing to temperature variation. 温度変化が生じて参照鏡を支持する部分が移動してもステージ位置計測を精度良く行うことができる位置検出装置を備えた露光装置を提供する。 - 特許庁
The operation part 42 compares the computed distance with a reference value stored beforehand in a storage portion 44, and computes the temperature of the substrate on the basis of the thermal expansion coefficient of the substrate. そして、演算部42が、算出した距離を記憶部44に予め記憶した基準値と比較し、基板の熱膨張率に基づいて基板の温度を算出する。 - 特許庁
The electric power steering device estimates a temperature of a motor based on a counter electromotive constant of the motor when a rotational speed ωm of the motor is at a reference rotational speed or higher. この電動パワーステアリング装置は、モータの回転速度ωmが基準回転速度以上のとき、モータの逆起電力定数に基づいてモータの温度を推定する。 - 特許庁
One theory states that 'mara' comes from 'me-ura' meaning 'one-eyed,' a reference to the practice of blacksmiths closing one eye in order to check the iron's temperature from its color (or to an occupational hazard of blacksmiths).
「マラ」は「目占(めうら)」すなわち片目の意で、鍛冶が鉄の色でその温度をみるのに片目をつぶっていたことから(または鍛冶の職業病である)とする説 - Wikipedia日英京都関連文書対訳コーパス
The predetermined numerical range or the reference variation value is set on the basis of the value and variation amount of the resonant frequency corresponding to the temperature change of the surgical instrument. 前記所定の数値範囲または基準変動値は、処置具の温度変化に対応した共振周波数の値および変動量に基づいて設定される。 - 特許庁
The liquid crystal display is provided with a panel temperature detection means of the liquid crystal display panel, and corrects gate-on voltage or a data signal pulse width, and a frequency of a reference clock signal according to the panel temperatures. 液晶表示パネルのパネル温度検出手段を有し、ゲートオン電圧もしくはデータ信号パルス幅、基準クロック信号の周波数をパネル温度により補正する。 - 特許庁
To prevent an error in determining an initial reference position during low temperature or battery voltage drop even in a structure with a crank shaft having a small number of teeth per rotation. クランクシャフトの1回転当たりの歯数が少ない構成においても、低温時やバッテリ電圧低下時における初回の基準位置の誤判定を防止すること。 - 特許庁
When finely adjusting the resistance value of a first resistor R3 concerned in generation of reference voltage in order to suppress "apex temperature variation" and "output voltage variation" of reference voltage V_ref due to element variation, the resistance value of a third resistor R4 which generates temperature sensor output V_PTAT is finely adjusted simultaneously in the same proportion. 素子ばらつきによる基準電圧V_refの「頂点温度ばらつき」と「出力電圧ばらつき」を抑えるために、基準電圧の生成に関与する第1の抵抗R3の抵抗値を微調整する場合、温度センサ出力V_PTATを生成する第3の抵抗R4の抵抗値も同時に、同比率で微調整する。 - 特許庁
The range of compared values of the forward voltages before and after the self-heating of the protective diode which correspond to a proper elevated temperature value is predefined as a reference value for use in determination, and the upper limit of the reference value is compared with the actually measured voltage values whereby excessive temperature rises, i.e., manufacturing (mounting) errors, can be detected. この時、適正な温度上昇値に対応する保護ダイオード8A、8Bの自己発熱前後の順方向電圧の比較値の範囲を予め判定用の基準値として決めておき、この基準値の上限と実際に測定した電圧値とを比較することで、温度上昇の異常、すなわち製造(マウント)不良を検出することができる。 - 特許庁
A simple crystal oscillator not needing temperature compensation is adopted for a reference signal of the synthesizer to enhance the C/N of the reference signal, a fraction frequency divider circuit capable of adjusting the output frequency in fine steps is adopted for a variable frequency division circuit of the synthesizer and the frequency division ratio is fine-tuned in matching with the ambient temperature change. 温度補償を必要としない単純な水晶発振器をシンセサイザーの基準信号に採用することにより基準信号のC/Nを改善し、また、シンセサイザーの可変分周回路に、出力周波数を細かなステップで調整できる分数分周回路を用い、この分周比を周囲の温度変化に合わせて微調する。 - 特許庁
A MOS control circuit 23 detects the temperature of the limiting resistor 21 by a thermistor 31 mounted at the limiting resistor 21, receives a voltage Vi lower than a reference voltage Vref when the temperature of the limiting resistor 21 rises higher than a reference value, outputs the signal of the L level to the AND circuit 34 and turns off the MOS transistor 22. MOS制御回路23は、制限抵抗21に取り付けられたサーミスタ31により制限抵抗21の温度を検出し、制限抵抗21の温度が基準値以上に上昇すると参照電圧Vrefよりも低い電圧Viを受け、Lレベルの信号をAND回路34へ出力してMOSトランジスタ22をオフする。 - 特許庁
In the apparatus, the temperature of the heated object 1 heated by the heating means 2 is detected by a temperature detecting means 3, and the heating means 2 is controlled by a controlling means 6 having a comparison operation means 5 that compares the output from a comparison voltage setting means 4 for setting one reference voltage out of a plurality of prescribed reference voltages with the outside input. 加熱手段2により加熱する被加熱体1の温度を温度検知手段3により検知し、複数の所定の基準電圧の中から1つの基準電圧を設定する比較電圧設定手段4からの出力と外部入力とを比較する比較演算手段5を有する制御手段6により加熱手段2を制御する。 - 特許庁
In the temperature compensated crystal oscillator constituted of a quartz resonator, an amplifier provided with an oscillation frequency control device and a temperature compensation circuit for the oscillation frequency of the quartz resonator, the reference voltage of a compensation voltage of the temperature compensation circuit is generated by using the forward voltage of a diode. 水晶振動子と、発振周波数制御装置を備えた増幅器と、水晶の発振周波数の温度補償回路と、で構成される温度補償型水晶発振器であって、前記温度補償回路の補償電圧のリファレンス電圧を、ダイオードの順方向電圧を使用して生成することを特徴とする。 - 特許庁
That is, the skin temperature of the upper-limb peripheral part and/or lower-limb peripheral part of the air-conditioned person staying in a prescribed space is detected, an air temperature of the prescribed space is detected when the difference in detected skin temperatures becomes more than a prescribed reference value, and the air conditioning is controlled to keep the detected air temperature. すなわち、所定空間に居る被空調者の上肢末梢部及び/又は下肢末梢部の皮膚温度を検出し、この検出された皮膚温度の差が所定の基準値よりも大きくなった際の所定空間の空気温度を検出し、この検出された空気温度を維持するように空調制御を行う。 - 特許庁
To enable calibration in a temperature range of 90-170 K or 77 K or lower that cannot be coped in the conventional calibration device by developing a device for calibrating a sheath thermometer at an arbitrary temperature by comparison with a reference thermometer without using a cooling liquid and a low temperature freezing mixture. 本発明は、冷却液や低温寒剤を用いずに、シース型温度計を任意の温度において基準温度計との比較により校正する装置を開発することにより、従来の校正装置では対応できていない90K〜170K、あるいは、77K以下の温度範囲での校正を可能にすることを目的とする。 - 特許庁
The fuel cell system executes cooling water temperature control of a cooling device 13 at a control device 26 to lower the temperature of the cooling water to a temperature which is set in accordance with a detected atmospheric pressure, when the detected atmospheric pressure detected by an atmosphere pressure detection means 25 is lower than an atmospheric pressure reference value. 大気圧検出手段25で検出された大気圧検出値が大気圧基準値より低い場合に、制御装置26において冷却装置13の冷却水温度制御を実行して、冷却水の温度を前記検出された大気圧検出値に応じて設定される温度に低下させるようにした。 - 特許庁