To provide an enhanced voltage comparator with a low operating current, to provide a voltage reference stable over a wide operating temperature range, and to provide simplified and reliable implementation of an integrated circuit. 動作電流が低い、改善された電圧比較器、広い動作温度の範囲に渡り安定している電圧基準、および集積回路の簡略的且つ信頼できるインプリメンテーションを提供すること。 - 特許庁
By this constitution, it is possible to form a resistance variable-type infrared detector with a unit area to suppress the effects of environment temperature gradient between the thermosensitive resistors (row) and reference resistors (row). これにより、感熱抵抗体(列)と基準抵抗体(列)との間の環境温度勾配による影響を抑えた単位領域を有する抵抗変化型赤外線検出器を形成できる。 - 特許庁
Reference temperatures T1 and T2 to be a boundary for target temperature switching are set to 90°C and 130°C respectively, and values TR1, TR2 and TR3 to be target temperatures are set to 110°C, 160°C and 180°C, respectively. ターゲット温度切り替えの境界となる基準温度T1、T2を90℃、130℃とし、ターゲット温度となる値TR1、TR2、TR3をそれぞれ110℃、160℃、180℃とする。 - 特許庁
At thermal expansion and contraction based on temperature changes, the sum of the distances between detecting planes of the sensors 11a and 11b and the outer circumferential surface of an intermediate part of the hub 2a varies with respect to the value at reference time. 温度変化に基づく熱膨張、熱収縮時には、上記両センサ11a、11bの検出面とハブ2aの中間部外周面との距離の合計値が、基準時に対し変動する。 - 特許庁
Based on a temperature signal and a humidity signal in a middle/high humidity measurement mode, a CPU 120 obtains the approximate conversion relative humidity (HUM1) in a reference resistance value and in the middle/high humidity measurement mode. 中高湿度測定モードでの温度信号および湿度信号に基づき、CPU120は基準抵抗値でかつ中高湿度測定モードでの近似換算相対湿度(HUM1)を求める。 - 特許庁
On the basis of the data on the water temperature with reference to the depth of water, in a depth-of- water precalculation part 4, a detectable region in an underwater search region to be searched is found regarding each depth of water of the part 1. 水測予察計算部4は、水深に対する水温のデータから、水中の捜索しようとする捜索領域における探知可能領域を送受波部1の各水深について求める。 - 特許庁
Accordingly, an electric signal level outputted from a heat-radiation type temperature sensor 40 also becomes lower than a reference value, and a signal of abnormal output is given to a controller 30 by an abnormality discrimination means 50. それに伴い、熱放射式温度センサ40から出力される電気信号レベルも基準値よりも低くくなり、出力異常信号が異常判別手段50からコントローラ30に与えられる。 - 特許庁
In the heating assist process, if SOC is higher than a reference value SOCth and if cooling water temperature Tw is equal to or greater than a reference value Twth, the ECU 100 mechanically drives (motors) the engine 200 using the torque of a motor generator MG 1 without burning fuel, and raises the cooling water temperature of the engine 200 using the friction of a piston 203 and the compression heat of intake air. 暖房アシスト処理において、ECU100は、SOCが基準値SOCthよりも大きく、また冷却水温Twが基準値Twth以上である場合に、モータジェネレータMG1のトルクによって燃料の燃料を伴うことなくエンジン200を機械的に駆動(モータリング)せしめ、ピストン203のフリクション及び吸入空気の圧縮熱によってエンジン200の冷却水温を上昇せしめる。 - 特許庁
The methods includes determining a combustion reference temperature of the gas turbine (202), measuring a biasing parameter of the gas turbine (204), determining at least one fuel split biasing value based on the combustion reference temperature and the biasing parameter (206) and adjusting a nominal fuel split schedule based on the at least one fuel split biasing value (208). 本方法は、ガスタービンの燃焼基準温度を決定する段階(202)と、ガスタービンのバイアス・パラメータを測定する段階(204)と、前記燃焼基準温度及び前記バイアス・パラメータに基づいて少なくとも1つの燃料分割バイアス値を決定する段階(206)と、前記少なくとも1つの燃料分割バイアス値に基づいて前記ガスタービンの公称燃料分割スケジュールを調節する段階(208)とを含むことができる。 - 特許庁
A light source apparatus includes a plurality of laser diodes, a temperature sensor mounted in neighborhood of the laser diodes, a control loop for controlling an oscillation wave length by controlling temperatures of the laser diodes based on an output of the temperature sensor, respectively, and a means for compensating a temperature control condition of other laser diodes according to a temperature control condition of a reference laser diode selected from the laser diodes. 本発明による光源装置は複数のレーザダイオードと、上記複数のレーザダイオードの近傍に設けられた温度センサと、上記温度センサの出力に基づき上記複数のレーザダイオードの各々の温度を制御することによりその発振波長を制御する制御ループと、上記複数のレーザダイオードから選択される参照レーザダイオードの温度制御条件に従って他のレーザダイオードの温度制御条件を補償する手段とを備えている。 - 特許庁
To obtain an apparatus for measuring the surface temperature of an object based on the state of fluorescence being emitted when the surface of the object covered with a temperature-sensitive coating containing a fluorescent substance and emitting temperature-dependent fluorescence is irradiated with exciting light in which the surface temperature of the object can be measured easily without requiring any extra measurement for reference. 本発明は、照射される励起光により蛍光を温度に依存して発する蛍光物質を含有する感温塗料7を物体6表面に被覆し、物体6表面に励起光を照射すると共に、発生する蛍光の状態から物体6表面の温度を求める温度測定装置1において、リファレンスを別途測定することなく簡易に物体の表面温度の測定を行なう技術を得ることを目的とする。 - 特許庁
This gas detector 1 applies reference voltage to a contact combustion type gas sensor 21 so that a reference region as a part of the contact combustion type gas sensor 21 reaches a combustion temperature for combusting polar gas or higher, and acquires an output from the contact combustion type gas sensor 21 driven by the voltage application. ガスセンサ装置1は、接触燃焼式ガスセンサ21の一部である基準領域が有極性ガスを燃焼させる燃焼温度以上となるように、接触燃焼式ガスセンサ21に基準電圧を印加し、この電圧印加によって駆動させられた接触燃焼式ガスセンサ21からの出力を取得する。 - 特許庁
A controller 50 performs absolute wavelength calibration for matching the detection reference wavelength of a beam monitor mechanism 164 with the absolute wavelength of an absorption cell 165 and set wavelength calibration for matching the detection reference wavelength with a set wavelength based on the temperature dependency map. そして、制御装置50では、吸収セル165の絶対波長に対してビームモニタ機構164の検出基準波長をほぼ一致させる絶対波長キャリブレーションを行うとともに、温度依存性マップに基づいて検出基準波長を設定波長に一致させる設定波長キャリブレーションを行う。 - 特許庁
When the scanner motor 25 does not reach the first reference speed Sp1 within the first period T1 (S100:No) and reaches a second reference speed Sp2 within a second period T2 after the first period T1 (S104:Yes), it can be determined that the scanner motor 25 is in a low acceleration state because of low temperature. また、スキャナモータ25が第1期間T1内に第1基準速度Sp1に到達せず(S100:No)、かつ第1期間T1より後の第2期間T2内に第2基準速度Sp2に到達した場合(S104:Yes)にはスキャナモータ25が低温のため低加速状態になっていると判断できる。 - 特許庁
When the sensor 2 is driven by a current Is based on a voltage Vs generally equal to the reference voltage Vr and the resistance value of the resistance R3, the sensitivity of the sensor 2 is corrected by the positive reference voltage Vr from a negative characteristic which is substantially constant, irrespective of a variation in ambient temperature. 従って、基準電圧Vrと略同じ値の電圧Vsと抵抗R3の抵抗値とに基づく電流Isによってセンサ2が駆動されると、センサ2の感度は、元々負特性であったものが、正特性の基準電圧Vrによって補正され、周囲温度の変化に関わらず略一定となる。 - 特許庁
The reference signal input in the bias line 11 is generated by a reference pixel 19 which is connected to a same power source 6 as that of pixels to detect only the fluctuation in element temperature, and adjusted to the optimum voltage by a level shift circuit and a low pass filter in a bias power supply circuit 21, and noises are eliminated thereby. バイアス線11に入力する参照信号は、画素と同一の電源6に接続され、素子温度変動だけを検出する参照画素19によって生成し、バイアス電源回路21内のレベルシフト回路と低域通過フィルタによって、最適電圧に調整すると共に雑音除去する。 - 特許庁
To provide a highly stable oscillation frequency control circuit by correcting its own frequency, specifying the inside of the proper range for an input level of an external reference signal according to the temperature characteristics in the detection of the external reference signal, and controlling the control voltage of a voltage-controlled oscillator, with respect to the inside and outside of the proper range. 自己の周波数を補正し、外部基準信号の検波における温度特性に応じて外部基準信号の入力レベルの適正範囲内を特定し、その適正範囲の内外に対して電圧制御発振器の制御電圧を制御して高安定な発振周波数制御回路を提供する。 - 特許庁
In the correcting method of the video correction portion, a plurality of reference data for correction, with respect to temperature are calculated by using a plurality of coefficient parameters of a quadratic equation and corrected video signals of a last video signal, and a current video signal are generated based on the reference data for correction and are outputted. そして、この映像補正部の補正方法は、複数の2次式の係数パラメターに基づき、温度に対する複数の補正用基準データを算出して、補正用基準データに基づいて直前の映像信号及び現在の映像信号に対する補正映像信号を生成して出力する。 - 特許庁
When individual light source lamp is shifted from a lighting state to a light out state, the notification system compares a time period t lapsed from the light out of the light source lamp and a reference time period ts required for the light source lamp to be cooled to a reference temperature and preliminarily stored for each light source lamp in a storage unit. 個々の光源ランプが点灯状態から消灯状態になったときに、光源ランプが消灯されたときからの経過時間tと,予め各光源ランプ毎に記憶部に記憶部に記憶されている、光源ランプが基準温度以下に低下するまでに必要な基準時間tsとを比較する。 - 特許庁
When power generation operation of the stack 2 is stopped, when the outside air temperature detected by the outside air temperature sensor 72 is equal or lower than a first prescribed temperature T1, an intermittent mode operation is carried out in which driving and stopping of the water conveying source 59 are alternatively repeated by a control part until a first prescribed time M1 passes from a reference time after stopping the power generation operation of the stack 2. 制御部は、スタック2の発電運転が停止されている場合において、外気温度センサ72で検知された外気温度が第1所定温度T1以下であるとき、スタック2の発電運転停止後における基準時刻から第1所定時間M1経過するまで、水搬送源59の駆動および停止を交互に繰り返す間欠モードを実行する。 - 特許庁
There is provided the image forming apparatus which is capable of reducing the temperature fluctuation at the end portion of the fixing member by correcting a reference temperature for maintaining the temperature of the fixing member in accordance with the displacement amount of the fixing member or the paper by a displacement means, thereby stably providing the image of high quality, and which has the improved durability of the fixing member. 本発明は、定着部材の温度を維持するための基準温度を変位手段による定着部材、あるいは用紙の変位量に応じて補正することにより、定着部材の端部に生じる温度変動を低減して、高品質な画像を安定的に提供可能な、定着部材の耐久性に優れた画像形成装置の提供を可能にする。 - 特許庁
If the temperature of the fuel cell 10 is lower than a given warming-up reference temperature, as a warming-up operation, the hydrogen tank 3 supplies hydrogen to the hydrogen storage alloy tank 2, which in turn stores the hydrogen in the hydrogen storage alloy to generate heat and transfers the generated heat to the fuel cell 10 via a heat exchanger medium to increase the temperature of the fuel cell 10. 燃料電池10の温度が所定の暖機基準温度よりも低い場合には,水素タンク3から水素吸蔵合金タンク2へ水素を供給し,水素吸蔵合金タンク2において水素吸蔵合金に水素を吸蔵させて熱を発生させ,発生した熱を熱交換媒体によって燃料電池10に伝達して燃料電池10の温度を上昇させる暖機作業を行う。 - 特許庁
In the circuit constitution of the liquid crystal display apparatus, an image data conversion circuit 14 refers to a digital γ table corresponding to an environmental temperature stored in a memory 14a from an environmental temperature of a liquid crystal display panel DP which is detected by a panel temperature detection circuit 9 and sets voltage becoming a same-gradation/same-luminance level in a gradation reference voltage generation circuit 7. 本発明の液晶表示装置の回路構成においては、画像データ変換回路14は、パネル温度検出回路9で検出された液晶表示パネルDPの環境温度から、メモリ14aに記憶された環境温度に対応するデジタルγテーブルを参照して同階調−同輝度レベルとなる電圧を階調基準電圧発生回路7に設定する。 - 特許庁
When the electronic device 3 is in an idle state, the control part controls the operation of the cooling fan on the basis of a correction temperature value obtained by correcting the reference setting value of the TAT in consideration of radiation heat from another electronic device 2. 電子デバイス3がアイドル状態のときには、他の電子デバイス2からの放射熱を考慮してTATの基準設定値を修正した修正温度値に基づいて冷却ファンの動作を制御する。 - 特許庁
To prevent reference value drift and accuracy deterioration by suppressing the dispersion of light absorption due to the dispersion of the temperature, pressure, and density of CO_2 gas in a method for measuring the purity of carbon dioxide (CO_2) by an optical fiber. 光ファイバによる二酸化炭素(CO_2)の純度を測定する方法において、CO_2ガスの温度、圧力、及び密度のばらつきによる光吸収のばらつきを抑えて基準値ドリフト及び精度低下を防ぐ。 - 特許庁
The memory means stores a function expression using a grayscale and a detected temperature as variables, the function expression which differs by each of a plurality of grayscale regions provided in the grayscale range where the reference gamma conversion data is set. 記憶手段は、階調と検出温度とを変数とする関数式であって、基準ガンマ変換データが設定された階調範囲内に複数設けられた階調領域ごとに異なる関数式を記憶する。 - 特許庁
To provide the reference current generating circuit of an EL driving circuit capable of reducing luminance change or color change caused by difference of temperature characteristics of light emitting materials of an organic EL panel and an organic EL display device using the same. 有機ELパネルの発光材料による温度特性の相違により発生する輝度変化あるいは色偏重を低減できる有機EL駆動回路および有機EL駆動回路を提供することにある。 - 特許庁
A circuit compares a first signal received from the first temperature budget sensor with a first reference signal, acquires first comparison results, and refreshes a plurality of multi-bit memory cells based on the first comparison results. 回路は、第1の温度バジェットセンサから受信した第1の信号と、第1の基準信号とを比較し、第1の比較結果を取得するとともに、第1の比較結果に基づいて、複数のマルチビットメモリセルをリフレッシュする。 - 特許庁
A control part 9 reads the correction corresponding to the temperature of the high frequency filters 5 and 6 detected by a thermistor 10 from the ROM 11, adds it to a reference changeover frequency and obtains the correction of the changeover frequency. 制御部9はサーミスタ10が検出した高周波フィルタ5、6の温度に対応する補正値をROM11から読みだし、これを基準の切り替え周波数に加算して切り替え周波数の補正値を求める。 - 特許庁
Each overdrive parameter corresponds to a graylevel transition between a previous frame and a current frame, and represents a level at which a liquid crystal is driven, in order to achieve a desired response time for the graylevel transition at a reference temperature. 各オーバドライブ・パラメータは先行フレームおよび現行フレーム間のグレーレベル遷移に対応し、基準温度でのグレーレベル遷移に望ましい応答時間を達成するために液晶が駆動されるレベルを表す。 - 特許庁
To stabilize searching by suppressing a variation in a travel time of reading means even when a mechanical load applied to a driving means is varied from a reference value by a variation in mechanism or a variation in ambient temperature. メカニズムのバラツキや周囲温度の変化によって駆動手段にかかる機械的な負荷が基準値から変動した場合でも、読取手段の移動時間の変動を抑制して、検索の安定化を図るようにする。 - 特許庁
Then, a threshold straight line L1 which passes through the reference point K1 and has an inclination according to the Boyle-Charles Law to be derived from the temperature of the tire included in the information signal and the air pressure of the tire is recognized. そして、この基準点K1を通過するとともに情報信号に含まれるタイヤの温度とタイヤの空気圧から導き出されるボイルシャルルの法則に従った傾きを有する閾値直線L1を認識する。 - 特許庁
The stagnation of the compressor is detected on the basis that the variation of motor temperature measured at two different times is smaller than a reference value, by distributing the power to the motor for a specific time so that the compressor is not rotated. 圧縮機が回転しないようにモータに所定時間通電し、互いに異なる2つのタイミングで計測したモータ温度の変化が基準値より小さいことを条件として圧縮機の寝込みを検知する。 - 特許庁
The real-time clock can correct the clocked time of the clocking circuit 5 by extending a time reference signal St in a time direction by a logical slowing/quickening circuit 6 on the basis of the temperature correction data. そして、リアルタイムクロック1は、論理緩急回路6がこの温度補正データに基づいて時間基準信号Stを時間方向に伸長することにより、計時回路5の計時時刻を補正することができる。 - 特許庁
If the reference signal cannot be obtained, the controller 22 determines a self-running control signal and controls the digital control oscillator 26 based on the corresponding relationship and a voltage and temperature detected by the detector 28. リファレンス信号が得られない場合、制御部22は、前記対応関係と、検出器28が検出した電圧及び温度と、に基づいて自走制御信号を決定し、デジタル制御発振器26を制御する。 - 特許庁
When an internal combustion engine stops, an element of a PM sensor is heated, if the resistance between PM sensor electrodes is smaller than a reference resistance, up to a first temperature so that PM deposited on the element can be heated and removed therefrom. 内燃機関の停止時において、PMセンサの電極間の抵抗が基準抵抗よりも小さい場合に、PMセンサの素子部を、第1温度に加熱して、素子部に堆積したPMを燃焼除去する。 - 特許庁
To provide a reference voltage generating circuit of a non-volatile memory in which temperature characteristics in accordance with each mode can be realized while reducing layout area by a regulator circuit for level compensation and one band gap circuit. レベル補正用レギュレータ回路と1つのバンドギャップ回路によってレイアウト面積を小さくしながら、各モードに応じた温度特性が実現できる不揮発性メモリの基準電圧発生回路を提供する。 - 特許庁
To provide a pulse width measuring apparatus for measuring a pulse width more accurately by an inexpensive circuit structure without using any high-sped clock signal obtained by multiplying a reference clock signal or any element of poor temperature characteristics. 本発明は、基準クロック信号を逓倍した高速クロック信号や温特の悪い素子を使用することなく、安価な回路構成で、より正確にパルス幅を測定できるパルス幅計測装置を提供する。 - 特許庁
The reference time difference ΔTcal is corrected by a NOx trap amount in starting the rich control, a reducing agent amount supplied to the NOx trap catalyst par unit time, and a temperature of the NOx trap catalyst (S405). 基準時間差ΔTcalは、リッチ制御開始時におけるNOxトラップ量、NOxトラップ触媒への単位時間当たりの還元剤供給量、及びNOxトラップ触媒の温度により補正する(S405)。 - 特許庁
Then a threshold straight line L1 that passes this reference point K1 and has the inclination according to the Boyle Charles' law derived from the temperature of the tire and the air pressure of the tire included in the information signal is set. そして、この基準点K1を通過するとともに前記情報信号に含まれるタイヤの温度とタイヤの空気圧から導き出されるボイルシャルルの法則に従った傾きを有する閾値直線L1を設定する。 - 特許庁
An amplification factor compensation signal generation circuit 13 compares the output voltage from the amplification factor monitor circuit 12 with a temperature independent predetermined reference voltage and generates an amplification factor compensation signal corresponding to a difference therebetween. 増幅率補償信号生成回路13は、増幅率モニタ回路12からの出力電圧と温度依存性のない所定の基準電圧とを比較し、その差に応じた増幅率補償信号を生成する。 - 特許庁
A server 52 for the oiling amount manager 50 compares the received temperature with management reference data stored in a database 54 and transmits oiling amount control information via the communication satellite 60 to the engine managing part 40. 注油量管理装置50のサーバ52は、受信した温度をデータベース54に格納してある管理基準データと比較し、通信衛星60を介して注油量制御情報をエンジン管理部40に送信する。 - 特許庁
To obtain a trimming circuit (100) and a method of trimming, that provides a trimming for offset and temperature drift of an operational amplifier or voltage reference device, having an input stage (120), on at least two different temperatures. 少なくとも2つの異なる温度において、入力ステージ(120)を有するオペアンプまたは電圧基準装置のオフセットおよび温度ドリフトのトリミングを提供するトリミング回路(100)およびトリミングの方法を得る。 - 特許庁
A driving pulse signal having a temperature-corrected proper period Din is generated using as a unit a phase difference ϕ of reference pulse signals output in order from a plurality of inversion circuits constituting the delay circuit 10. 該遅延回路10を構成する複数の反転回路から順次出力される参照パルス信号の位相差φを単位として、温度補正された適正周期Dinを有する駆動パルス信号を発生させる。 - 特許庁
A reference current control circuit 500 comprises a temperature sensor 21, a voltage-current conversion circuit 22, a cancel circuit 23, a switch 24, a time constant circuit 25 for controlling the switch 24, and an adder circuit 26. 基準電流制御回路500は、温度センサー21と、電圧−電流変換回路22と、キャンセル回路23と、スイッチ24と、スイッチ24を制御する時定数回路25と、足し算回路26とを備えている。 - 特許庁
To more precisely detect full charged state than before in charge control with temperature as a reference when applied to, for example, a portable audio device, related to the charging circuit and the charging method of a battery. 本発明は、充電回路及びバッテリの充電方法に関し、例えば携帯型のオーディオ装置に適用して、温度を基準にした充電の制御において、従来に比して満充電を精度良く検出する。 - 特許庁
A power circuit 600 has a correcting circuit 610 having a correction table LUTr outputting a reference voltage Vref1 according to temperature and a source voltage supply circuit 620 having a voltage adjusting circuit 621. 電源回路600は、温度に応じた基準電圧Vref1を出力する補正テーブルLUTrを備えた補正回路610と、電圧調整回路621を備えた電源電圧供給回路620を有する。 - 特許庁
In the control of the fan, the output of the fan is determined by using the characteristic curves of the fan motor, operating parameters of a cooling system, and reference input variables pre-determined in the form of temperature levels. 本発明は、ファンの出力が、ファンモーターの特性曲線、冷却システムの運転パラメーター、及び温度レベルの形態で予め定められた基準入力変数から決定されるファンの制御に関する。 - 特許庁
A computer body 2a of the manager 2 counts the duration of an inadequate condition, as an irregular time, where excessive cooling/heating operation is found from the room temperature compared with a reference value during cooling/heating operation of the air conditioning equipment M. 管理装置2のコンピュータ本体2aは、空調機器Mの冷暖房運転時に室内温度を基準値と比較して過剰な冷暖房運転をしている「不適正」な状態の継続を違反時間としてカウントする。 - 特許庁
As a result, it is eliminated that a change of a cooling operation to the element 22 for a heating operation to the element 22 is repeatedly performed in the vicinity of the reference temperature as seen in the conventional method, wasteful power can be reduced and the element 22 is prevented from being deteriorated. これにより、従来のように、基準温度付近で冷却動作と加熱動作との切り換えを繰り返し行うことがなくなり、無駄な電力を削減でき、ペルチェ素子22の劣化を防げる。 - 特許庁