「solid-fuel」を含む例文一覧(6746)

<前へ 1 2 .... 124 125 126 127 128 129 130 131 132 .... 134 135 次へ>
  • The method for producing a waste oil-based solid fuel O includes disintegrating waste sludge A by a disintegrator 2, crush-mixing the disintegrated product obtained by such disintegration and an adjusting waste oil X by a crush-mixer 4, and mixing the mixture Y obtained by crush-mixing and a waste oil absorbent W.
    廃スラッジAを解砕機2により解砕し、該解砕によって得られた解砕物を調整廃油Xと破砕混合機4により破砕混合し、該破砕混合によって得られた混合物Yと廃油吸収材Wとを混合する、廃油系固体燃料Oの製造方法とした。 - 特許庁
  • To provide a method for manufacturing a solid electrolyte which is high in ionic conductivity in a wide temperature range especially even at a low temperature, can prevent phase transition from occurring even with a reaction temperature condition changed, is excellent in stability of a crystal structure, and can be used for an oxygen sensor and a fuel cell.
    幅広い温度域、特に低温においてもイオン伝導度が高く、反応温度条件が変化しても相転移の発生が防止でき、結晶構造の安定性に優れる、酸素センサや燃料電池に使用可能な固体電解質を提供することである。 - 特許庁
  • To provide a solid polymer electrolyte membrane, its manufacturing method, and a fuel cell using the same which exhibit stably a favorable electricity generating performance in a long period at an operation temperature of about 100°C to 300°C under an operation condition of non-humidity or not more than 50% in relative humidity.
    100℃から300℃程度の作動温度において、無加湿あるいは相対湿度50%以下の作動条件で良好な発電性能を長期間安定的に示す固体高分子電解質膜およびその製造方法並びに固体高分子型燃料電池を提供する。 - 特許庁
  • To provide a solid polymer electrolyte fuel cell power generating device in which process monitoring is made possible by extracting a signal for maintenance outside the power generating device, and furthermore in addition to this, in which a process monitoring equipment is imparted with waterproofness, and with miniturization, and superior appearance design as the power generating device.
    保守用の信号を発電装置の外部に取り出してプロセス監視を可能とすること、さらに、これに加えて、プロセス監視機器は防水性を備え、かつ発電装置としては小形で外観デザインが良好な固体高分子電解質型燃料電池発電装置を提供する。 - 特許庁
  • The solid oxide fuel cell stack is provided inside the manifold with a spiral-shaped repair member 10, capable of turning with an axis along a lamination direction of the single stacks as a center, and the repair member 10 is arranged at a position of the gas flow channel 7, connecting the manifold and the power generating cells.
    固体酸化物形燃料電池スタックは、マニホールドの内部に、単スタックの積層方向に沿った軸を中心として回動可能な螺旋状の補修部材10を備え、補修部材10は、マニホールドと発電セルとを繋ぐガス流路7の位置に配置される。 - 特許庁
  • To obtain a subsidiary fuel composition for cement calcination without separtion between water and oil during storage and without separation of a solid part such as sand, which is prepared in combination with two or more kinds of wastes, and can be readily transported into piping by lowering viscosity when flowing to carry out spray burning.
    2種類以上の廃棄物を組み合わせて作られる、貯蔵中の水と油の分離がなく、砂などの固形分の分離もなく、流動時には粘度が低くなって容易に配管輸送、噴霧燃焼を行えるセメント焼成用補助燃料組成物を提供する。 - 特許庁
  • To provide a production apparatus for a solid fuel which prevents the closure of a heat exchanger or a raw material coal supplying means, even when the supply of a raw material coal (RC) or a mixed oil (MO), or the supply of a slurry to the next process is stopped due to the occurrence of a trouble after the evaporation process.
    蒸発工程以降でのトラブル発生等により原料炭(RC)や混合油(MO)の供給やスラリーの次工程への供給を停止した時であっても熱交換器や原料炭供給手段の閉塞を防止する固形燃料の製造装置を提供すること。 - 特許庁
  • A gas conduction manifold is formed in a higher part in the direction of gravity than a gas ejection manifold, a gas ejection opening is formed in a higher part in the direction of gravity than the gas ejection manifold and furthermore, the connection angle α of a gas conduction opening is made to be 90°<α≤180° in the direction of gravity in the solid polymer electrolyte fuel cell.
    ガス導入マニホールドを、ガス排出マニホールドよりも重力方向上部に形成し、また、ガス排出マニホールドの重力方向上部にガス排出口を形成し、更には、ガス導入口の接続角度αを、重力方向に対し、90°<α≦180°とする。 - 特許庁
  • To improve the utilization efficiency of resource by effectively utilizing the large amount of heat generated at a power generation system as many as possible, by improving a power generation /hot water supplying cogeneration system constructed by combining the hot water supplying system (4) with the power generation system (2) including a solid electrolyte fuel cell (22).
    固体電解室型燃料電池(22)を含む発電システム(2)に給湯システム(4)を組み合わせた発電・給湯コジェネレーションシステムを改良して、発電システムにおいて生成される多量の熱を可及的に有効利用して資源の利用効率を向上せしめる。 - 特許庁
  • By means of porosity adjustment of the fuel electrode 12, the rate of hydrogen gas permeation to the solid electrolyte interface is reduced in the region having a higher hydrogen concentration so as to suppress the battery reaction, and in the region having a low hydrogen gas concentration, the rate of permeation of hydrogen gas is heightened to promote the battery reaction.
    燃料極の気孔率の調整により、水素濃度の高い領域では固体電解質界面への水素ガス透過率を低減し、電池反応の抑制を図り、水素ガス濃度の低い領域では水素ガスの透過率を上げ、電池反応の促進を図る。 - 特許庁
  • By setting the clamp pressure within the range of 3-6 kg/cm^2 when clamping both ends of the laminated cells by the clamp means, the desired electrical performance and service life are obtained and a miniaturized and lightened solid high polymer fuel cell is obtained.
    積層セルの両端間を締め付け手段で締め付ける際に、締め付け圧力を3〜6kg/cm^2の範囲に設定することにより、所望の電気性能及び寿命を得ると共に、小型化及び軽量化された固体高分子型燃料電池を得ることにある。 - 特許庁
  • In a process for firing cement clinker, the flammable resins having an average diameter of 5 to 30 mm is spouted into a kiln from an injection hole for a mixture of flammable solid particulate fuel and conveying air, which is provided at the outlet side of the cement rotary kiln, so that the flammable resins are burned in a clinker layer.
    セメントクリンカー焼成工程において、平均粒子径が5〜30mmである可燃性樹脂を、セメントロータリーキルン出口側に設けた可燃性固体粒状燃料/搬送用空気混合物用噴射孔でキルン内に噴出し、該可燃性樹脂をクリンカー層内で燃焼させるように構成する。 - 特許庁
  • This separator for the solid polymer electrolyte fuel cell is constructed by coating the surface of stainless steel, having an overall surface corrosion resistance coefficient GI [GI=(Cr%)+3.6(Ni%)+4.7(Mo%)+11.5(Cu%)] of 90 or more with a film containing a conductive compound such as metal nitride, metal-dispersed diamondlike carbon.
    固体高分子電解質型燃料電池用セパレータを、耐全面腐食係数GI=[Cr%]+3.6[Ni%]+4.7[Mo%]+11.5[Cu%]が90以上であるステンレス鋼の表面に、金属窒化物や金属分散ダイヤモンドライクカーボンなどの導電性化合物を被覆したもので構成する。 - 特許庁
  • To provide a solid polymer fuel cell of a high output and high durability, by making an electrolyte film of low cost by turning into practical application of a PEFC or a DMFC, of high ionic conductivity, and with less variations in the dimensions under water in an area direction, due to superior water resistance.
    PEFCやDMFCの実用化のために安価で、イオン伝導度が高く、かつ、優れた耐水性を有するために水中での面積方向の寸法変化小さい電解質膜を作製し、高出力,高耐久性の固体高分子形燃料電池を提供することである。 - 特許庁
  • The current collector material for the solid oxide fuel cell is a perovskite-type oxide expressed by a general formula A (Ni_1-xFe_x)O_3 (A is more than one element selected from a group of rare-earth elements, and the range of x is 0<x<1).
    本発明の固体酸化物形燃料電池用の集電体材料は、一般式A(Ni_1−xFe_x)O_3(ただし、Aは希土類元素の群から選ばれる1つ以上の元素であり、xの範囲は0<x<1である)で表されるペロブスカイト型酸化物である。 - 特許庁
  • To provide a solid oxide fuel cell equipped with an air electrode reaction layer, capable of restraining diffusion of Ca into electrolyte, by clarifying states of the air electrode reaction layer in which elements in an air electrode conductive layer material, especially, Ca, tends to diffuse into ZrO_2 series electrolyte.
    空気極導電層材料中の元素、特にCaがZrO_2系電解質に拡散しやすい空気極反応層の状態を明らかにし、Caの電解質への拡散を抑制することができる空気極反応層を備えた固体酸化物型燃料電池を提供する。 - 特許庁
  • To provide an adhesive sealing composition for a solid polymer electrolyte fuel cell separator, of which the cured product has little compression set and moreover capable of making a sealing structure having an excellent adhesiveness to various kinds of separator base materials, especially an excellent adhesiveness durability as well.
    固体高分子型燃料電池用セパレータの接着性シール組成物として、その硬化物は圧縮永久歪が小さく、かつ各種セパレータ基材との接着性、特に接着耐久性も良好なシーリング構造を与える接着性シール組成物を提供する。 - 特許庁
  • To provide an SOFC (Solid Oxide Fuel Cell) in which a heat receiving area of a reformer can be made large easily, and in which stable operation is enabled without reducing efficiency, and the reformer suitable for this SOFC in an indirect internal reform type SOFC to heat the reformer by a radiation heat from the SOFC.
    SOFCからの輻射熱によって改質器を加熱する間接内部改質型SOFCにおいて、改質器の受熱面積を容易に大きくでき、効率を低下させずに安定運転が可能となるSOFCと、このSOFCに好適な改質器を提供する。 - 特許庁
  • To provide a method for preparing an alloy catalyst of which the degree of alloying of an active metal is high and the active metal can be converted into fine particles and which has a high activity even when its metal content is low; and to provide a method for producing a solid polymer-type fuel cell exhibiting an excellent resistance to CO poison and a high active reaction.
    活性金属の合金化度合いが高く、合金の微粒子化が可能で、かつ低金属量であっても高活性な合金触媒の調製方法と、耐CO被毒性に優れ、かつ高い活性反応を有する固体高分子型燃料電池の製造方法を提供する。 - 特許庁
  • To provide a method for treating plastics which decreases sublimated compounds generated in a dechlorination process of a mixture of plastics, causes little operation troubles such as clogging of pipes of an apparatus and gives usable materials such as a solid fuel, a reducing agent for an ore and the like.
    プラスチック混合物を脱塩素化する過程で発生する昇華物が低減され、装置の配管閉塞などによる操業トラブルが極めて少なく、固体燃料や鉱石用還元剤などの有用物を得ることができるプラスチック混合物の処理方法の提供。 - 特許庁
  • The manufacturing method mixes and calcinates raw materials of an air electrode material for a solid oxide fuel cell (steps S1 and S2), and holds the raw materials during second time at second temperature lower than first temperature after holding the raw materials during first time at first temperature (step S3), repeating the above steps by the predetermined number of times.
    固体酸化物形燃料電池の空気極材料の原料を混合して焼成し(ステップS1,S2)、これを第1の温度で第1の時間保持した後に第1の温度よりも低い第2の温度で第2の時間保持し(ステップS3)、これを所定回数繰り返す。 - 特許庁
  • To provide a raw material for a dense thin film capable of forming a thin film denser than a conventional one even on a dense ceramic substrate, to provide a dense thin film using the same, and to provide a solid oxide fuel cell single having an intermediate layer and having more excellent electricity generation performance than a conventional performance.
    緻密セラミック基体上であっても、従来より緻密な薄膜を形成することが可能な緻密薄膜用原料、これを用いた緻密薄膜、及び従来より発電性能に優れた、中間層を有する固体酸化物形燃料電池単セルを提供する。 - 特許庁
  • To provide a material for a solid polymer type fuel cell in which the softness of the material capable of securing the precision of groove forming is improved in the case of a hard metal base material and which is low in cost, while maintaining adhesion, corrosion resistance, and contact electric resistance or the like of the membrane, and provide its manufacturing method.
    皮膜の密着性、耐食性、接触電気抵抗等を維持しつつ、硬い金属ベース材の場合には溝成形精度が確保できる素材の柔らかさを改善したコストの低い固体高分子形燃料電池用素材及びその製造方法を提供すること。 - 特許庁
  • This solid polymer type fuel cell 5A is formed, by applying end plates 3 and 4 to both ends of a laminate 2 consisting of a number of unit cells 1 followed by fastening and integrating, and a heat medium chamber 6 is provided between one end plate 4 and the unit cell 1A on the end part of the end plate 4 side.
    単位セル1を多数重ねた積層体2の両端に端板3,4を当てて締め付け一体化することで固体高分子形燃料電池5Aを形成し、一方の端板4とこの端板4側の端部の単位セル1Aとの間に熱媒室6が設けられる。 - 特許庁
  • The solid oxide fuel cell comprises an anode collector layer containing CaZrO_3, and Ni or NiO; a cathode; an electrolyte layer between the anode collector layer and the cathode; and an anode active layer between the electrolyte layer and the anode collector layer.
    固体酸化物型燃料電池は、CaZrO<sub>3</sub>と、Ni又はNiOと、を含有する燃料極集電層と、空気極と、燃料極集電層と空気極との間に配置される電解質層と、電解質層と燃料極集電層との間に配置される燃料極活性層と、を備える。 - 特許庁
  • To provide a moisture control sheet capable of manufacturing in good productivity and manufacturing a gas diffusion sheet which is excellent in shape preservation characteristics and gas diffusion characteristics, to provide the gas diffusion sheet using the moisture control sheet, to provide a membrane-electrode assembly, and to provide a solid polymer fuel cell.
    生産性良く製造することができ、形態保持性に優れるとともに、ガス拡散性の優れるガス拡散シートを製造することのできる水分管理シート、この水分管理シートを用いたガス拡散シート、膜−電極接合体及び固体高分子形燃料電池を提供すること。 - 特許庁
  • Since a larger amount of raw pseudo particle materials consisting of a raw ferromagnetic material containing iron and a solid fuel are segregated in the upper part of the layer of the raw material for sintering formed on the pallet, the sintering property of the upper layer of the raw material for sintering is improved, and the yield and the cold strength of the sintered ore are improved.
    パレット上に形成される焼結原料層の上層部に強磁性含鉄原料と固体燃料とからなる疑似粒子原料が多く偏析するので、焼結原料層の上層部の焼結性が改善され、焼結鉱の歩留や冷間強度の向上が達成される。 - 特許庁
  • As for the electrodes 3, 4 for the solid polymer fuel cell, after the gas diffusion layers 3a, 4a and the catalyst layers 3b, 4b are jointed, plasma treatments are applied thereto, and proton deviation groups 22 are introduced to catalysts 21 on surfaces of the catalyst layers 3b, 4b and around surfaces of the catalyst layers 3b, 4b.
    固体高分子型燃料電池用電極3,4では、ガス拡散層3a,4aと触媒層3b,4bとを接合した後にプラズマ処理が施されて、触媒層3b,4b表面および触媒層3b,4b表面付近の触媒21にプロトン乖離基22が導入されている。 - 特許庁
  • To 100 wt.% of a mixture in which 30 to 50 wt.% of paper sludge, and 70 to 50 wt.% of woody wastes are mixed after its water adjustment, 0.7 to 0.9 wt.% of a binder is added, to provide the solid fuel 1 that is a molded article by pressure forming.
    ペーパースラッジ30〜50重量%、木質廃材70〜50重量%の割合で配合した混合物100重量%に対し、水分調整した後、バインダー0.7〜0.9重量%を添加し、加圧成形して成る成形物である固形燃料1を提供する。 - 特許庁
  • This solid oxide fuel cell 100 is provided with a stack 101 formed into a long shape along a gas flow direction, a pair of manifolds 81a, 81b on both sides of a gas passage of the stack 101, and a heat insulation means 90 intervening among the stack 101 and the manifolds 81a, 81b.
    固体電解質型燃料電池100は、ガス流れ方向に長尺に形成されたスタック101と、該スタック101のガス流路の両側に配備された一対のマニホールド81a,81bと、スタック101とマニホールド81a,81bの間に介在する断熱手段90と、を備えている。 - 特許庁
  • If ash concentration in the organic material 101 gets high, the probability of contact between the solid component of the organic material and the ash derived therefrom inevitably gets high, enabling to fully perform the capability of decomposing the organic material 101 which the ash has, and thereby a large quantity of gas having a high fuel value such as hydrogen can be produced.
    有機物101内の灰分濃度が高くなると、必然的に固形分と灰分の接触確率も高くなり、灰分が有する有機物101の分解能力を十分に発揮し、水素等の燃料として価値の高いガスを多量に生成することが可能になる。 - 特許庁
  • To provide a method of producing a solid electrolyte fuel cell with an interconnector composed of La1-xMxCrO3, M:Ca or Sr giving adaptability to mass production, a decrease in production cost and high-performance generation characteristics.
    La_1-xM_xCrO_3,M:Ca、又はSrの組成からなるインターコネクターを有する固体電解質型燃料電池の製造方法において、量産性に適し、製造コストの低下が可能であり、かつ高性能な発電特性を有する固体電解質型燃料電池の製造方法を提供する。 - 特許庁
  • The operation method includes using the above solid fuel as a main heat source, when producing molten pig iron for steel-making by charging the scrap iron as a main iron source and the charcoal wood as the main heat source into the vertical scrap-melting furnace provided with a blowing tuyere 2 in a lower part of the furnace, from the furnace top, and melting the scrap iron.
    この固体燃料を、炉下部に送風羽ロ2を設けた竪型スクラップ溶解炉内へ、主鉄源の鉄スクラップ及び主熱源の炭材を炉頂から装入し、鉄スクラップを溶解して製鋼用溶銑を製造するに際して、主熱源の固体燃料として用いる。 - 特許庁
  • To minimize the performance deterioration of a reversible cell with a solid polymer water electrolysis device and a fuel cell which are integrated, when operated for a long period, while eliminating the need for special control, an electrolytic current higher than a rated current, a current supply installation and the sustaining operation of a pump or the like.
    固体高分子形の水電解装置と燃料電池とを一体化させた可逆セルにおいて、格別な制御、定格以上の電解電流、電流供給設備、ポンプの持続運転等を必要とせず、長期的な運転に伴う性能低下を最小限に抑える。 - 特許庁
  • There is provided a sheet which is an electrolyte sheet for a solid oxide fuel cell, and of which the relative ratio of flexural strength at three points measured by using one side (A side) and the other side (B side) of the electrolyte sheet as the upper surface, respectively, is 105-200%.
    固体酸化物形燃料電池用の電解質シートであって、該電解質シートの片面(A面)ともう一方の面(B面)をそれぞれ上面として測定した3点曲げ強度の相対比が、105〜200%であるシートであるところに特徴を有したシートを提供する。 - 特許庁
  • To provide inexpensive steel for a solid oxide type fuel battery separator on which an oxide film having a satisfactory electric conductivity at about 700 to 950°C is formed, and which has satisfactory oxidation resistance, in particular, peeling resistance even on use for a long time, and has a reduced difference in thermal expansion with an electrolyte.
    700〜950℃程度において良好な電気伝導性を有する酸化被膜を形成するとともに、長時間の使用においても良好な耐酸化性、特に耐剥離性を有し、かつ電解質との熱膨張差が小さい安価な固体酸化物型燃料電池セパレータ用鋼を提供する。 - 特許庁
  • To provide a defect inspection method and a defect inspection device of a laminate, capable of detecting a defect of the laminate in a nondestructive/noncontact manner, regardless of the material of the laminate, and utilizable, for example, for deterioration diagnosis of for a solid oxide type fuel cell or process inspection at manufacturing.
    積層体の材質に左右されることなく、積層体の欠陥を非破壊・非接触で検出しることができ、例えば固体酸化物形燃料電池の劣化診断や、製造時の工程検査などに利用することができる積層体の欠陥検査方法及び欠陥検査装置を提供する。 - 特許庁
  • To provide a method for producing a scandia stabilized zirconia sheet which exhibits stable, excellent ion electrical conductivity, further has sufficient strength and high temperature durability on handling, and has excellent performance as the one for a solid electrolytic membrane of a fuel battery, an oxygen generator, an oxygen sensor, or the like.
    安定して優れたイオン導電率を示すと共に、ハンドリングに十分な強度と高温耐久性を有し、燃料電池や酸素発生器、酸素センサーなどの固体電解質膜用として優れた性能を有するスカンジア安定化ジルコニアシートの製法を確立すること。 - 特許庁
  • In the solid polymer fuel cell formed by stacking an anode side gas diffusion layer, an anode catalyst layer, a polymer electrolyte membrane, a cathode catalyst layer, and a cathode side gas diffusion layer in this order, the water vapor permeability ratio of the cathode side gas diffusion layer to that of the anode side gas diffusion layer is prescribed to 1.1-1.5.
    アノード側ガス拡散層、アノード触媒層、高分子電解質膜、カソード触媒層、カソード側ガス拡散層がこの順に積層された固体高分子型燃料電池において、アノード側ガス拡散層に対するカソード側ガス拡散層の水蒸気透過性比を1.1〜1.5とする。 - 特許庁
  • The glass frit having SiO_2 as a principal component has an added amount of 0.5-1.5% at a weight ratio against the principal component of the conductive paste, a softening point of the glass frit is lower than operation temperature of the solid oxide fuel battery, and crystallization temperature is higher than the operation temperature.
    ガラスフリットは、SiO_2 を主成分とし、導電性ペーストの主成分に対して重量比で0.5%以上1.5%以下の添加量を有し、軟化点が固体酸化物形燃料電池の動作温度よりも低く、かつ結晶化温度が動作温度よりも高い。 - 特許庁
  • Then, the molding is reground, mixed with a ground material of PET bottles being a relatively pure waste plastic and a ground material of a thermoplastic resin as an industrial waste, melted, packed into a mold and solidified to give the solid fuel having approximately fixed combustion calories.
    次いで、この成形品を再度粉砕し、これを比較的純粋な廃棄プラスチックであるPETボトル粉砕材および、産業廃棄物としての熱可塑性樹脂粉砕材と混合溶融金型内に充填して固形化し、燃焼熱量のほぼ一定に調整した燃料とする。 - 特許庁
  • To provide a solid oxide fuel cell cogeneration system and its operation control method, capable of improving tracking ability of a thermoelectric ratio and durability, without making facilities complicated, and with a temperature state of a system, such as, cell temperature or offgas combustion temperature maintained stable at changing of a thermoelectric ratio.
    設備を複雑にすることなく、熱電比変更時にセル温度やオフガス燃焼温度などシステムの温度状態を安定に保ちながら、熱電比追従性と耐久性を向上できる固体酸化物形燃料電池コジェネレーションシステムとその運転制御方法を提供する。 - 特許庁
  • To provide a solid polymer type fuel cell having an excellent power generation characteristic and excellent durability by providing a mass-producible membrane-electrode junction having a thin electrolyte membrane and/or a catalyst layer having a uniform thickness, and is low resistance and high tear strength and easy to handle.
    厚さが均一で薄く抵抗が低く、引裂き強度が高くてハンドリング性に優れる電解質膜及び/又は触媒層を融資、量産が可能な膜・電極接合体を備えることにより、発電特性及び耐久性に優れる固体高分子型燃料電池の提供。 - 特許庁
  • This solid polymer fuel cell comprises the polymer electrolytic film nipped by a pair of electrodes, and the polymer electrolytic film is formed by subjecting an aromatic ion conductive material, having a maximum moisture content retainable in an untreated state of 80-300 wt.% with respect to the whole material to hot water treatment.
    一対の電極に挟持された高分子電解質膜を備え、該高分子電解質膜は、未処理の状態で保持できる最大の水分量が材料全体に対して80〜300重量%の範囲にある芳香族系イオン導伝性材料に熱水処理を施してなる。 - 特許庁
  • The organic substance such as excess sludge etc., with a strong odor and a high water content is effectively deodorization dried by a reduced pressure fermentation dryer 1, and becomes usable as a component of the solid fuel, consequently, the vast cost required for abandoning excess sludge can be reduced.
    臭いがきつく、水分含有量が多い余剰汚泥等の有機物を減圧発酵乾燥機1によって効果的に脱臭乾燥することにより、固形燃料の成分として利用可能となるので、余剰汚泥の廃棄に要していた多大な経費の削減を図ることができる。 - 特許庁
  • The electrolyte sheet for the solid oxide fuel cell is manufactured by using raw material ceramic powder comprising electrolyte powder having an average particle size of 0.2-1 μm and oxide nano particles (excepting alumina nano particles) having an average particle size of 10-100 nm.
    上記課題は、原料セラミック粉末が平均粒子径0.2〜1μmの電解質粉末と平均粒子径10〜100nmの酸化物ナノ粒子(ただし、アルミナナノ粒子を除く)とからなることを特徴とする固体酸化物形燃料電池用電解質シートにより達成することができる。 - 特許庁
  • To provide a polyelectrolyte membrane for a solid polymer-type fuel cell having a high ion exchange capacity and a high proton conductivity by solving the problem of the deterioration of the material characteristics of a base material by causing graft reaction to a fluorinated polymer through irradiation of radiation beam.
    フッ素系高分子に放射線照射してグラフト反応させることによって基材の材料特性が低下する問題を解消し、かつ、高イオン交換容量、高プロトン伝導性を有する固体高分子形燃料電池用の高分子電解質膜を提供する。 - 特許庁
  • To produce high purity water without using an ion exchange resin which requires frequent exchange by treating condensed water of a solid polymer-type fuel cell or city water being supplying water by using an electrical deionization device capable of continuously treating for a long period of time without maintenance.
    頻繁に交換を行うことが必要なイオン交換樹脂を用いることなく、メンテナンス不要で長期連続処理が可能な電気脱イオン装置により固体高分子型燃料電池の凝縮水や補給水としての水道水を処理して高純度水を製造する。 - 特許庁
  • In a membrane electrode assembly with which the electrolyte membrane and the electrode of the solid polymer fuel cell are joined by being cross-linked by using a positive ion exchange resin, this is the membrane electrode assembly is obtained by using a cross-linker in which the positive ion exchange resin is shown as an adhesive in the following chemical formula (1).
    固体高分子型燃料電池の電解質膜と電極を、陽イオン交換樹脂を用いて接合された膜電極接合体において、接着剤として陽イオン交換樹脂が化学式(1)で示される架橋剤を用いて架橋して得られた膜電極接合体。 - 特許庁
  • A solid waste 1 is thermally decomposed to a thermal decomposition gas 8 and a thermal decomposition residue (char) 10 in a thermal decomposition furnace 7 of a thermal decomposition apparatus and the thermal decomposition residue 10 is supplied to a furnace 21 of a boiler to be burned solely or in form of a mixture with other fuel.
    固形廃棄物1を、熱分解装置の熱分解炉7で熱分解ガス8と熱分解残さ(チャー)10に熱分解し、熱分解残さ10をボイラーの火炉21に供給して燃料として単独で燃焼させるか、もしくは他の燃料と混合して燃焼させる。 - 特許庁
<前へ 1 2 .... 124 125 126 127 128 129 130 131 132 .... 134 135 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.