To reduce a temperaturedifference between coated fuel particles of a fuel comprising a plurality of kinds of coated fuel particles having each different enrichment, and thereby to remove a thermal or mechanical influence of the coated fuel particles to avoid fracture thereof; and also to reduce the difference of a thermal expansion amount of a graphite matrix to prevent crack of the fuel. 濃縮度が異なる複数の種類の被覆燃料粒子から成る燃料の被覆燃料粒子間の温度差を小さくして被覆燃料粒子の熱的、機械的影響をなくしてその破損を回避し、また黒鉛マトリックスの熱膨張量のさも小さくして燃料の割れを防止する。 - 特許庁
In this charge control method to use the storage battery in the partial state of charge (PSOC), a maximum temperaturedifference among cells in use is controlled to be 15°C or less, and the recovery charge is periodically performed to correct the difference from the PSOC of the storage battery in use. 蓄電池を部分充電状態(PSOC)で使用する充電制御方法において、使用中の各単電池(セル)間の最大温度差が15℃以下となるように制御し、さらに使用中の蓄電池のPSOCからのずれを是正するために定期的に回復充電を行うことを特徴とするものである。 - 特許庁
Continuous energy is obtainable by the difference in the susceptibility per spatial volume from a difference in magnetization inclination per temperature of the fluid so that high energy is continuously obtainable with less put-in energy. 2種類以上の感温磁性体を混層させ水を配合することから磁束密度の勾配の違いを利用し、磁化率の変化が生じ、感温磁性流体の温度あたりの磁化勾配の違いから空間上の体積当たりの磁化率の違いによって連続したエネルギーが得られ、低投下エネルギーで高エネルギーを連続し、得られた。 - 特許庁
By providing this bearing mechanism, while excellent heat transfer is maintained by adding an axial force in a longitudinal direction, a heated object is made to slide by the bearing mechanism in a lateral direction so as to absorb a thermal expansion difference, and a change of flatness caused by a mutual thermal expansion difference is prevented to secure temperature uniformity in the wafer face. このベアリング機構を備えることによって、縦方向に軸力を加えることで良好な熱伝達を保ちながら、横方向には熱膨張差を吸収できるようにベアリング機構で滑らせ、互いの熱膨張差による平面度変化の発生を防止して、ウエハ面内の温度均一性を確保する。 - 特許庁
Further as the inner tubes of a plurality of nozzles are arranged in a state of not overlapped to each other on the heat insulating layer of the combustor nozzle, the difference in physical length caused by expansion and contraction of the tubes caused by temperaturedifference between the outer tube and the inner tube at the part can be absorbed, and the long service life of the outer tube and the inner tube can be achieved. また、燃焼器ノズルの断熱層において、複数のノズルの内管が互いにオーバーラップしないように配置されるため、この部分で外管と内管との温度差で生じる管の伸縮による物理的な長さのズレを吸収することができ、外管および内管の長寿命化を図ることができる。 - 特許庁
In the optical system including a first optical element and a second optical element, first zero-cross temperature where the coefficient of linear expansion of the first optical element becomes zero is different from second zero-cross temperature where the coefficient of linear expansion of the second optical element becomes zero, and the difference between the first zero-cross temperature and the second zero-cross temperature is within 3°. 第1光学素子と第2光学素子とを含む光学系であって、前記第1光学素子の線膨張係数がゼロになる温度を第1ゼロ交差温度、前記第2光学素子の線膨張係数がゼロになる温度を第2ゼロ交差温度とするとき、前記第1ゼロ交差温度と前記第2ゼロ交差温度とが互いに異なる温度であり、前記第1ゼロ交差温度と前記第2ゼロ交差温度との差が3度以内であることを特徴としている。 - 特許庁
The temperature white defect correction unit obtains a difference of pixel values between the pixels at positions corresponding to the two fields by each region, discriminates whether or not either of both the pixels is defective depending on the sign of the difference when the difference between both corresponding pixels exceeds a prescribed threshold range, and corrects the value of the pixel discriminated to be defective by using the pixel value of the other pixel. 温度白キズ補正装置は、2つのフィールドの互いに対応する配列位置の各画素間の画素値についての差分を領域毎に求め、対応する両画素間の差分が所定の閾値範囲を越えるとき、その差分の符号に応じて、両画素のいずれか一方の画素が欠陥画素であると判定し、欠陥画素であると判定された一方の画素の画素値を他方の画素の画素値で補正する。 - 特許庁
When the catalyst temperature estimation allowing condition is satisfied after starting an internal combustion engine, element impedance Riu and Rid of air fuel ratio sensors provided in the upstream and the downstream of the catalyst are detected, And when a difference between these values exists within the predetermined value, the element temperature Tu and Td estimated on the basis of each element impedance are processed for meaning so as to compute the catalyst temperature Ts. 内燃機関の始動後、触媒温度推定許可条件が成立したときに、触媒上流側及び下流側に設けられた空燃比センサの素子インピーダンスRiu、Ridを検出し、これらの値の差が所定値以内のときに各素子インピーダンスから推定した素子温度Tu、Tdを平均化処理して触媒温度Tsを算出する。 - 特許庁
To provide an injection molding method capable of performing injection molding so as to reduce the temperaturedifference between the temperature of a resin at the time of injection in a resin injection process and the temperature of a mold to the utmost when a molding cycle is extended and contracted to perform injection molding to suppress the lowering of the quality of a molded product, and a production system control method using it. 成形サイクルを伸縮して射出成形するに際し、樹脂射出工程における射出時の樹脂温度と金型温度との温度差を可及的に生じさせないで射出成形することができ、成形品の品質低下を抑制することが可能となる射出成形方法、該射出成形方法を用いる生産システム制御方法を提供する。 - 特許庁
This heat pump device controls refrigerant enthalpy in the same as the heating medium inlet temperature, the heating medium outlet temperature regulated by a heating medium use temperature setting means 15, a refrigerant pressure arithmetic operation means 10b becoming maximum in an enthalpy difference with the same refrigerant enthalpy, and a rotating speed of a compressor 1 so as to become high pressure not less than its refrigerant pressure and not more than preset high pressure. 熱媒体入口温度と同一の冷媒エンタルピーと、熱媒体利用温度設定手段15によって規定された熱媒体出口温度と同一の冷媒エンタルピーとのエンタルピー差が最大となる冷媒圧力演算手段10bとその冷媒圧力以上かつ設定高圧圧力以下の高圧圧力になるように、圧縮機1の回転速度を制御する。 - 特許庁
Temperature independence of the optical waveguide for the resonant wavelength of the optical waveguide is achieved by imparting residual stress in the optical waveguide; and polarization independence of the resonant wavelength is achieved by controlling the resonant wavelength difference in the polarized light beams by controlling temperature by using different temperature characteristics of the resonant wavelengths of the polarized beams propagating through the optical waveguide and having polarization directions orthogonal to each other. 光導波路は、光導波路の内部に残留応力を持たせることによって、光導波路の共振波長の温度無依存化を図り、また、光導波路を伝播する直交する偏光の共振波長の温度特性が異なることを用い、温度制御を行うことによって両偏光の共振波長差を制御して共振波長の偏光無依存化依を図る。 - 特許庁
This fuel injection amount controller comprises a control means having an incremental control part incrementally controlling the injected amount of a fuel in increments of set injection amount for each set time elapsed when an engine water temperature detected by an engine water temperature detection means is lower than a set water temperature and an engine speed detected by an engine speed detection means is lower by a set speed difference than a target speed. エンジン水温検出手段により検出されたエンジン水温が設定水温より低く、且つ、エンジン回転数検出手段により検出されたエンジン回転数が目標回転数よりも設定回転数差以上低いときには、燃料噴射量を設定時間経過毎に設定噴射量ずつ増量制御する増量制御部が備えられた制御手段を設けている。 - 特許庁
This method for producing an unsaturated carboxylic acid ester comprises feeding an unsaturated carboxylic acid and an aliphatic alcohol into a reactor having a heating measure on the outer periphery and is characterized by having ≤80°C temperaturedifference between the temperature of the outer periphery of the reactor heated by the heating measure and the average temperature of the reacting liquid in the reactor. 外周部に加熱手段を有する反応槽に不飽和カルボン酸と脂肪族アルコール類とを供給する不飽和カルボン酸エステルの製造方法において、該加熱手段によって加熱される反応槽外周部の温度と、反応槽内の反応液の平均温度との温度差が80℃以下であることを特徴とする、不飽和カルボン酸エステルの製造方法である。 - 特許庁
The conductor accommodation recess 30h is filled with a metal material in a compressed state at a temperature that is lower than room temperature before returning to room temperature, thus performing cooling fitting treatment for increasing compressive stress to the laminar conductor element 30, based on the difference in the expansion displacement between the ceramic material for forming the conductor accommodation recess 30h and the metal material for forming the laminar conductor element 30. 導体収容凹部30hへは金属材料を室温よりも低温にて圧縮状態にて充填し、その後室温に戻すことにより、導体収容凹部30hを形成しているセラミック材料と、層状導体要素30をなす金属材料との膨張変位の差に基づいて該層状導体要素30に対する圧縮応力を増加させる冷やし嵌め処理を行なう。 - 特許庁
A first dew formation estimated condition applied for estimating an occurrence of dew formation is set in response to a predetermined relation between a temperaturedifference between an external surrounding temperature and a compartment temperature when an inner surface of a glass shows a dew formation, and an indoor humidity, and in addition, a second dew formation estimated condition applied for estimating an occurrence of dew formation is set before the former condition is satisfied. 予め求めたガラスの内面が結露する場合の車外温度と室内温度との温度差と室内湿度との関係に基づいて結露が発生することを推定するために用いる第1の結露推定条件を定め、またこの条件が満たされる前に結露が発生するものと推定するために用いる第2の結露推定条件を定める。 - 特許庁
To provide an image forming apparatus capable of surely preventing the damage of a device easily affected by thermal effect in the image forming apparatus by changing a power for driving a heat discharging apparatus in accordance with a temperaturedifference between a temperature inside the device including a heat source in the image forming apparatus body and the outside temperature of the image forming apparatus. 画像形成装置の機内における熱源を有する装置の機内温度と画像形成装置の機外温度との温度差に応じて排熱装置を駆動する電力を変化させることで、熱源を有する装置で発生する熱による画像形成装置の機内において熱の影響を受けやすい装置の損傷等を確実に防止することができる画像形成装置を提供する。 - 特許庁
An internal defect 5 dominantly appears as difference of surface temperature because a heat quantity of heat 3 given to an inspection object 1 larger than a heat quantity of heat 7 considerably raises the surface temperature of the inspection object 1, and a heat flow generated thereby is reflected in the internal defect 5, which raises the temperature of a surface 2 of the inspection object 1. 内部欠陥5が表面温度の差として顕著に表れているのは、被検査体1に対して与えられる熱3の熱量が熱7の熱量よりも大きいため、被検査体1の表面温度が大きく上昇し、これによって生じた熱流が内部欠陥5において反射することによって、被検査体1の表面2の温度を上昇させているためである。 - 特許庁
Such a heating means is equipped that the mouthpiece is heated so that the magnitude of unevenness of temperature in the width direction becomes less than 1% for an absolute value of difference of both the temperature of a molten material made to the sheet and room temperature. そして、AリップおよびBリップの先端部の間には幅方向に略均一な間隔の間隙部が形成され、AリップおよびBリップの中央部の間には幅方向に延在するマニホールドが形成されおり、幅方向の温度むらの大きさが、シート化する溶融材料の温度と室温の差の絶対値に対して1%以内になるように口金を加熱する加熱手段を備える。 - 特許庁
For reproduction, the information on the temperature is obtained from the header information of the hologram recording medium and the temperature detected by the temperature detection unit is acquired to determine the quantity of a shift in reproduction wavelength for canceling the influence of the dimension change between the recording and reproduction of the hologram recording medium based upon the difference between the acquired temperatures, thereby shifting the oscillation wavelength of a wavelength-variable laser. 再生時には、ホログラム記録媒体のヘッダ情報から温度の情報を取得するとともに、温度検知ユニットより検知された温度を取得し、取得した各温度の差に基づいて、ホログラム記録媒体の記録時と再生時との間でのディメンジョン変化による影響を打ち消すための再生波長のシフト量を決定して、波長可変レーザの発振波長をシフトさせる。 - 特許庁
The plurality of power consumption apparatuses are sequentially started or stopped, or subjected to capacity control in accordance with priority set in advance so that the sum of power consumption correspondent to a temperaturedifference between a set temperature and a suction temperature of each of the plurality of power consuming apparatuses 2 inputted by a power input means 4 reaches the target power inputted by a target power input means 5. 電力入力手段4により入力された複数の電力消費機器2の設定温度と吸込み温度との温度差に応じた消費電力合計が目標電力入力手段5により入力された目標電力になるように、あらかじめ設定した優先度に応じて複数台の電力消費機器を順次発停あるいは能力制御する。 - 特許庁
In order to evaluate the remaining catalytic operability of a catalyst, temperature TE of exhaust gas at an outlet of a catalyst and temperaturedifference ΔT between TE and ignition temperature TCO,50,flesh of the carbon monoxide in a new catalyst which is stored in the catalyst as a function of a speed and a load ΔT=TE-TCO,50,flesh are measured to determine the conversion ratio rCO of the carbon monoxide. 触媒の残存触媒活性を評価するために、特定のオペレーティングポイントにおけるその時点での排気ガスの触媒出口温度T_Eと、速度と負荷の関数として記憶させてある新たな触媒における一酸化炭素の着火温度T_CO、50%、フレッシュとの差であるΔT、 を測定し、一酸化炭素の転化率r_COを求めることである。 - 特許庁
An outdoor unit control portion 6 executes the control to increase an opening of an expansion valve 4 and a rotating speed of an outdoor unit fan 15 to prevent overheating of a refrigerant, when the difference between a refrigerant temperature near a discharge opening of a compressor 1, and the outside air temperature or a refrigerant temperature near an outflow port of an outdoor heat exchanger 5 becomes more than a prescribed value. 室外機制御部6は、冷房時には、圧縮機1の吐出口の近傍の冷媒の温度と外気の温度または室外熱交換器5の流出口の近傍の冷媒の温度との差が所定値より大きくなれば、冷媒の過熱を抑制するために、膨張弁4の開度を大きくするとともに、室外機ファン15の回転速度を大きくする制御を実行する。 - 特許庁
To provide an optical compensation laminate film having reverse dispersion properties sufficient to achieve an ideal phase difference (λ/4 (nm)) throughout a visible-light region and capable of suppressing degradation in optical compensation performance at high temperature. 可視光領域の全域において理想の位相差(λ/4(nm))を実現できる充分な逆分散性を有し、更に高温下での光学補償性能の劣化を抑制できる光学補償積層フィルムを提供する。 - 特許庁
The control part 86 calculates the difference value between the dark current intensity for the long carrier storage time and that for the short carrier storage time of the photoelectric conversion element 20 and obtains the measured temperature from the correspondence table. 制御部86は、光電変換素子20の長キャリア蓄積時間での暗電流強度と短キャリア蓄積時間での暗電流強度との差分値を算出し、対応表より測定温度を求める。 - 特許庁
The outdoor heat exchanger 15 is provided in a place where the temperaturedifference between the outside air around the radiator 6 of a first circulation circuit 3 and the cooling water passing the outdoor heat exchanger 15 of a second circulation circuit 12 is large. ここで、室外熱交換器15は、第1循環回路3のラジエータ6周りの外気と第2循環回路12の室外熱交換器15を通過する冷却水との温度差の大きくなる箇所に設けられる。 - 特許庁
To provide the reference current generating circuit of an EL driving circuit capable of reducing luminance change or color change caused by difference of temperature characteristics of light emitting materials of an organic EL panel and an organic EL display device using the same. 有機ELパネルの発光材料による温度特性の相違により発生する輝度変化あるいは色偏重を低減できる有機EL駆動回路および有機EL駆動回路を提供することにある。 - 特許庁
A cataphoresis is detected by making a physical volume reflecting a distribution of mercury inside the discharge lamp La, out of the lowering of lamp voltage of the discharge lamp La or the change of temperaturedifference between both end parts of the discharge lamp La. 放電ランプLaのランプ電圧の低下あるいは放電ランプLaの両管端部の温度差の変化を放電ランプLaの内部での水銀の分布を反映する物理量としてカタホリシスを検出する。 - 特許庁
To decrease a difference in temperature between heads for liquid heated and fed in a liquid delivering apparatus in which a plurality of the heads are arranged in the paper width direction and an image is formed by delivering liquid droplets from the head. 複数のヘッドが紙幅方向に並べられ、ヘッドから液滴を吐出することで画像を形成する液体吐出装置において、加熱されて供給される液体のヘッド間における温度差を少なくすること。 - 特許庁
To provide a plasma processor capable of achieving high uniformity by reducing a warpage amount generated by a temperaturedifference between a plasma irradiation face side of a dielectric and a metal electrode side being a rear face of the plasma irradiation face side due to plasma generation as much as possible. プラズマの発生により誘電体のプラズマ照射面側とその裏面の金属電極側との温度差により生ずる反り量をできるだけ低減して均一性の高いプラズマプロセス装置を提供する。 - 特許庁
To prevent difference in level between an upper end face of open deck type cylinder block and an upper end face of a cylinder liner caused by temperature rise in operating an engine, without changing a cylinder liner form and metallic mold structure. シリンダライナー形状及び金型構成を変更しなくとも機関運転による昇温によりオープンデッキ型シリンダブロックの上端面とシリンダライナーの上端面との間に段差が生じることを防止する。 - 特許庁
To provide a desiccant air conditioner capable of having large humidity difference in dehumidification even with a low temperature heat source, thus the outside air can be dehumidified to be lower than an ordinary indoor set humidity, in particular, at midsummer. 低温熱源であっても除湿湿度差を大きくとることができ、それにより、特に盛夏時の外気を通常の室内設定湿度以下まで除湿することができるようなデシカント空調装置を提供する。 - 特許庁
By controlling the temperaturedifference between the inner and outer faces of the piping 15, the distortion of the steam oxidation scales of the piping 15 is controlled, and the separation of the steam oxidation scales on the inner face of the piping can be prevented. 配管15の内外面の温度差を制御することにより配管15の水蒸気酸化スケールのひずみを制御し、配管内面の水蒸気酸化スケールが剥離するのを防止することができる。 - 特許庁
Then the heat roller 66a and pressure roller 66b are supplied with electric power alternately to raise the temperatures of both rollers up to corresponding temperatures Taa°C and Tb°C of high-speed printing while maintaining the temperaturedifference A' between both rollers. その後、熱ローラヒータ66aと圧ローラヒータ66bを交互に通電して両ローラの温度差A´を維持したまま両ローラの温度を高速印字の対応温度Taa℃とTb℃まで上昇させていく。 - 特許庁
To provide a fuel cell superior in reliability by improving the service life and output of the whole battery, by eliminating a difference between the temperature and the output caused between the center and the periphery of a membrane-electrode assembly. 膜電極接合体の中央と周辺との間で生じる温度および出力の差が解消され、寿命および電池全体の出力が向上した信頼性に優れた燃料電池を提供する。 - 特許庁
To provide a method for arranging slabs in a walking beam heating furnace with which a temperaturedifference in the longitudinal direction of the slab can be reduced without lowering the treating capacity when the slabs having different lengths are arranged and heated. 長さが異なるスラブを配置して加熱する際に、スラブ処理能力を低下させずに、スラブの長手方向の温度差を小さくすることができるウォーキングビーム加熱炉内におけるスラブの配置方法を提供する。 - 特許庁
To reduce thermal stress generated by a difference in a linear expansion coefficient and variations in temperature between an outer tube which is a magnetic material enabling induction heating and an inner tube through which heated fluid is made to flow. 誘導加熱が可能な磁性体である外管と、被加熱流体を通流させる内管との間の、線膨張係数の違いおよび温度ばらつきによって生じる熱応力を緩和することを目的とする。 - 特許庁
To provide an apparatus for manufacturing patterned tempered glass, in which the temperaturedifference between inner and outer parts of a glass substrate subjected to heating and surface pattern formation is increased to the maximum, and thereby tempering is more thoroughly performed through rapid cooling. 表面のパターン形成と共に加熱されたガラス基板の内外部の温度差を最大に大きくし、急冷却を通じて強化がより完全になされるようにするパターンド強化ガラスの製造装置を提供する。 - 特許庁
To provide a laser beam machining apparatus that prevents thermal distortion from occurring on a metallic surface plate even if a difference in temperature takes place in a stone surface plate and the metallic surface plate and that maintains a transmitting optical system in a prescribed state. 石定盤と金属定盤とに温度差が発生しても金属定盤に熱歪みが発生することを防止し、伝送光学系を所定の状態に維持することができるレーザ加工装置を提供する。 - 特許庁
By adopting BaO as a tunnel material and reducing the difference in the lattice constant between the silicon and the tunnel material compared to a conventional material, decline of the spin injection efficiency in a high temperature range is suppressed. トンネル材料としてBaOを採用し、シリコンとトンネル材料との間の格子定数の差を従来材料に比べて低減することで、高温域におけるスピン注入効率の低下が抑制される。 - 特許庁
To provide a laminating device that relaxes damage to a diaphragm by eliminating or suppressing a temperaturedifference generated between an upper surface and a lower surface of a substrate to be subjected to laminating processing, and has a short cycle time and high productivity. ラミネート処理する基板の上下面の間に生じる温度差を解消または抑制してダイヤフラムの損傷発生を緩和でき、しかも、タクトタイムが短く生産性の高いラミネート装置を提供する。 - 特許庁
To provide a production device and method which suppress the generation of the deformation caused by a temperaturedifference between the end part in the width direction and the central part in the production of a sheet-shaped sintered compact by energizing pressure sintering with rolls. ロールによる通電加圧焼結によりシート状焼結体の製造において、幅方向端部と中央部との温度差による変形の発生を抑える製造装置および製造方法を提供する。 - 特許庁
To provide a spindle device, in which imbalance in a lubricant amount supplied into a hollow part of a rotating shaft is hardly caused and the occurrence of temperaturedifference for each rolling bearing can be suppressed, even during high speed rotation. 高速回転の場合でも、回転軸の中空部内に供給される潤滑油量に不均衡が生じ難く、転がり軸受毎に温度差が生じることを抑制できる主軸装置を提供する。 - 特許庁
Daytime surplus heat in the greenhouse is efficiently heat exchanged through the heat transfer plate 32 of the heat exchange-thermal storage device 30 by the temperaturedifference between the thermal storage body filled in the heat exchange-thermal storage device 30 and greenhouse air. 熱交換・蓄熱器30の伝熱板32を介して、日中の温室内の余剰熱を、該熱交換・蓄熱器30内に充填された蓄熱体と温室内空気との温度差で効率よく熱交換できる。 - 特許庁
To provide a heat-resistant drain trap which is prevented from being cracked or deformed even if hot drain water is discharged therethrough, usable in cold regions where there is a temperaturedifference or in winter season, and can withstand the ultraviolet of the sun. 温度の高い排水が排出されても割れや変形が無く、更には、寒冷地の温度差がある地域や、冬期に用いられたり、更には太陽の紫外線にも耐えうる耐熱性排水トラップを提供する。 - 特許庁
To further save power without degrading image quality for a print job that has a plurality of pages, in a fixing control (prior art) performed by setting a target temperature for each page according to a difference in dither. ディザの違いに応じてページごとに目標温度を設定して行う定着制御(先行技術)において、複数のページよりなる印刷ジョブに対して画質を低下させること無くさらに省電力を図ること。 - 特許庁
To provide a molding device for an optical element which performs soaking in such a manner that a temperaturedifference in a molding mold therein is hard to occur, and manufactures an optical element with high precision at a high yield. 本発明は、成形装置の成形型内の温度差を生じにくいように均熱化し、この均熱化によって、高精度の光学素子を歩留まり良く製造する光学素子の成形装置を提供する。 - 特許庁
Thus, the heat-electric power converting part 21 collects the heat energy as the electric energy according to a temperaturedifference between one surface side 21a contacting with the sliding member 12a and the other surface side 21b contacting with the plate member 12b. これにより、熱電変換部21は、摺動部材12aに接触する一面側21aとプレート部材12bに接触する他面側21bとの温度差に応じて熱エネルギーを電気エネルギーとして回収する。 - 特許庁
To provide a RAID controller device, a RAID device, and a processing method and program for the RAID device capable of minimizing the temperaturedifference in each hard disk, and lengthening the life of each hard disk. ハードディスク毎の温度差を最小限に抑えて、各ハードディスクの長寿命化を図ることが可能なRAIDコントローラ装置、RAID装置、RAID装置の処理方法及びプログラムを提供する。 - 特許庁
To provide a fixed bed multitubular reactor allowing sufficient reduction of a temperaturedifference inside the reactor, allowing sufficient utilization of an internal space of the reactor, and having no restriction in the diameter and the number of reaction tubes. 反応器内部における温度差を充分に小さくできる上に、反応器の内部空間を充分に利用でき、また、反応管の本数と太さが制限されない固定床多管式反応器を提供する。 - 特許庁
To provide a rotor for a rotating electric machine, which is cooled without causing the difference in temperature of a permanent magnet, preventing a coolant from remaining, and reducing the influence of a rotating reactive force from the coolant. 永久磁石に温度差を生じることなく、且つ、冷媒が滞留することのない、冷媒から受ける回転反力の影響を軽減して冷却することが可能な回転電機用ロータを提供する。 - 特許庁