The variation of an electromotive voltage due to the pattern of charging and discharging and the variation of the electromotive voltage due to temperature variation are taken into account because they are canceled when the difference ΔV of the voltage is obtained, so that the abnormality of the set battery can correctly by determined. 充放電のパターンによる起電圧の変動、温度変化による起電圧の変動は電圧の偏差ΔVを求める際に相殺されることにより考慮されているから、より正確に組電池の異常を判定することができる。 - 特許庁
Here, the longer the heating time is, the larger the temperaturedifference between the primary medium kept into contact with a flame tube and that kept into contact with a second medium, becomes, and the thermal storage effect of the primary medium can be exercised. このボイラーのすぐれているところは、1次媒体が炎管に接触しているところと2次媒体に接触しているところとの温度差が加熱される時間が長いほど大きくなり、1次媒体の蓄熱効果がより発揮されるところにある。 - 特許庁
In this construction, the heat resistance of the film is improved because the difference between the heat expansion coefficient of the film and that of the base material at a high temperature is small, that is the inner tension accumulated in the film having the siloxane bond on the surface of the base material is small. この構成により、高温時にこの膜の熱膨張率と基体の熱膨張率の差、すなわちこの基体表面上のシロキサン結合を有する膜に蓄積される内部応力が小さいため、この膜の耐熱性を向上できる。 - 特許庁
If the temperaturedifference between the inlet side and the outlet side when cooling water is cooled by a cold and hot water pipe 15 from a high pressure side evaporator 11 to a low pressure side evaporator 12 is higher than rated 5°C, the coefficient of performance COP can be more improved. 高圧側蒸発器11から低圧側蒸発器12まで冷温水管15で冷水の冷却を行う際の入側と出側との温度差を定格の5℃よりも大きくすれば、一層成績係数COPを高めることができる。 - 特許庁
Therefore, even if there is a temperaturedifference of, for example, 70°C between the inner side and outer side of a package, external heat conducted via the wire for power supply is reduced by the repeating bases 7 cooled by the insulating substrate 2 and then reaches the LD 1. 従って、パッケージの外部と内部との間に、例えば70℃もの温度差があっても、外部からの給電ワイヤを介しての入熱は、絶縁基板2により冷却される中継台7によって緩和されてから、LD11まで到達する。 - 特許庁
The first transport path 45 and the third transport path 47 are partially, at least, made proximate to each other, and the thermoelectric transducer 49 which generates electric power according to a temperaturedifference between the first transport path 45 and the third transport path 47 is arranged in the proximate portion. ここで、第1輸送路45と第3輸送路47は、それらの少なくとも一部が近接され、その近接した部分の間に、第1輸送路45と第3輸送路47との温度差により発電する熱電変換素子49が配されている。 - 特許庁
The entire exhaust line inner volume V of the storage buffer and the exhaust gas line is set sufficiently larger than a difference ΔV between the volumes of the gas at stopping time and normal temperature and normal pressure time of an overall amount of the gas sealed from the valve 32a to the valve (33). 貯留バッファと排気ラインの全排気ライン内容積Vが、原料遮断弁32aから排気調節弁(33)までに封入される全ガス量の停止時と常温常圧時の容積差ΔVよりも十分大きく設定されている。 - 特許庁
As a result of displacing the heater 5, temperature gradient in an oblique direction with respect to the narrow core part 31 is formed and distribution of light does not reach the heat dissipating substrate 41 and difference in attenuation between TE and TM mode light is suppressed and the polarization dependent loss is consequently suppressed. ヒータ5をずらした結果、狭小コア部31に対して斜め方向の温度勾配が形成され、光の分布は放熱基板41まで達しなく、TE/TMモード光の減衰の差が抑制されて偏波依存損失が抑制される。 - 特許庁
To provide an electric current bonding apparatus which can perform a uniform bonding by controlling the temperaturedifference caused in the joining surfaces between metallic members regardless of shapes and sizes of the metallic members to be bonded in the case of performing the electric current bonding of the metallic materials to each other. 金属材料を相互に通電接合する場合に、接合する金属部材の形状や大きさに係わらずに金属部材間の接合面に生じる温度差を抑制して均質な接合を可能にした通電接合装置を提供する。 - 特許庁
To provide an electron bombardment heating device in which thermal stress caused by a temperaturedifference between a bottom end part of a heating object supporting part and a heating plate at the time of heating of the heating plate is alleviated, and breakage of the heating object supporting part is prevented even if heating and cooling of the heating plate are repeated. 加熱プレートの加熱時の加熱物支持体の下端部と加熱プレートとの間の温度差により生じる熱応力を緩和し、加熱プレートの加熱と冷却を繰り返しても、加熱物支持体が破断することが無いようにする。 - 特許庁
To provide an apparatus which prevents a substrate from being partly deformed to cause a positional deviation because of the temperaturedifference between the substrate and a substrate support member when the substrate is replaced in a heat treating furnace, and does not deteriorate the throughput. 熱処理炉内への基板の入れ替えに際し、基板と基板支持部材との間の温度差が原因で基板が部分変形して基板の位置ずれを生じる、といったことを防止でき、スループットを低下させることもない装置を提供する。 - 特許庁
A potential difference is generated between a voltage in a connection point between a resistance R_kh and a resistance R_kL of the bridge circuit and a constant voltage means 100, and a current flows in the fourth resistance R_kp, in the change from the specified ambient temperature (specified heater resistance R_H). 特定の周囲温度(特定のヒータ抵抗R_H )からの変化時に、ブリッジ回路の抵抗R_khと抵抗R_kLとの接続点の電圧と、定電圧手段100との間に電位差が発生し、第4の抵抗R_kpに電流が流れる。 - 特許庁
To sharply enhance the commercial value by simplifying the constitution of a floor heating panel and raising the installation workability and productivity, reducing the cost, and reducing the temperature irregularity of the surface, and notwithstanding, removing the rubbing noise between parts caused by the difference of thermal expansion coefficient. 床暖房パネルの構成を簡素化し、施工性、生産性を高め、コストを低減し、それでいて、表面の温度むらを低減し、かつ、熱膨張率の違いに起因する部品間の擦れ音の発生をなくして商品価値を大幅に高める。 - 特許庁
To provide a thermoelectric conversion module that is hard to suffer concentration of a thermal strain even when the thermoelectric conversion module is installed in an area where a temperaturedifference is large, does not destroy a joint portion of a thermoelectric transducer and an electrode, and has a high mechanical strength. 熱電変換モジュールを温度差の大きい領域に設置した場合でも熱歪の集中を受け難く、熱電変換素子と電極との接合部分が破壊することがなく、機械的強度の高い熱電変換モジュールを提供する。 - 特許庁
To provide a method of manufacturing a crystallized glass capable of forming minute dents, juts etc. on the surface of the crystallized glass without using a chemical liquid such as hydrofluoric acid and not liable to break by thermal impact even if a temperaturedifference of use environment is large. フッ酸等の薬液を使用しなくても、結晶化ガラスの表面に微細な窪みや突起等を形成することができ、且つ使用環境の温度差が大きくても、熱衝撃により破損し難い結晶化ガラスの製造方法を創案すること。 - 特許庁
With the above, even when the balance of the sensor tubes 14, 15 is changed by a temperature and then behaviors (amplitude and frequency) are changed, the phase difference signal unaffected by the torsional vibrations can be obtained and thereby a high pressure fluid can be measured precisely. これにより、センサチューブ14,15のバランスが温度などで変化して、捩れ信号の挙動(振幅や周波数)が変化しても捩れ振動の影響がない位相差信号が得られるので、精度よく高圧流体を計測することができる。 - 特許庁
To obtain such a container that structural destruction of the container can be prevented against difference in pressures between the inside and the outside of the container caused by a change in atmospheric pressure and a change in temperature while ventilation from the outside of the container is shut to protect a machine against dust and humidity. 塵芥及び湿気から機器を保護するためにコンテナ外部からの通気を遮断したままで、大気圧の変化及び温度の変化により生じるコンテナ内部と外部の圧力差からコンテナの構造破壊を防止できるコンテナを得る。 - 特許庁
The difference between the threshold voltage Vt of the transistor and the voltage Va applied across the resistance 18 is set to be within a range from 0.1 V to 0.4 V, and thus the current In flowing to the restance 18 becomes constant without depending on temperature change. トランジスタのしきい値電圧Vtと抵抗18の両端にかかる電圧Vaとの差が0.1Vから0.4Vの範囲内に設定されることにより、抵抗18に流れる電流Irが温度変化に依存せずに一定となる。 - 特許庁
First - fourth Peltier elements for power generation P1-P4 are mounted in regions where the temperaturedifference of a cabinet body 10 is generated, so that a clock 34, etc., is driven with the electromotive force generated by the first - fourth Peltier elements for power generation P1-P4. キャビネット本体10の温度差が生じる部位には第1〜4発電用ペルチェ素子P1〜4が設けられ、第1〜4発電用ペルチェ素子P1〜4によって生じる起電力に起因して時計34等が駆動されるようになっている。 - 特許庁
To provide a scroll fluid machine preventive of radial overload on a pin crank type self-rotation preventing mechanism provided across fixed scrolls and a rotary scroll when a difference in diameter occurs therebetween with temperature rise accompanying operation. スクロール流体機械において、運転に伴う温度上昇によって、固定スクロールと旋回スクロールの径に差が生じた際において、両者間に跨設されているピンクランク式自転防止機構に径方向の過大な負荷が作用するのを防止する。 - 特許庁
The first and the third layer 10a, 10c which are the same temperature sensitive magnetic material are designed to have the same thickness while the second layer 10b is designed to have the thickness to minimize thermal deformation due to difference in thermal expansion coefficient. 同じ感温磁性材である第1の層10aおよび第3の層10cとは、同じ厚さ寸法とし、それに対する第2の層10bの厚さ寸法も、熱膨張率の違いに起因する熱変形を最小限とするべく設定する。 - 特許庁
By such constitution, the inner tube and the outer tube are simultaneously thermally expanded regardless of temperaturedifference between the inner tube and the outer tube found when a steam generator is normally operated, a degree of adhesion of the inner tube and the outer tube is not lowered. このような構成によって、蒸気発生器が正常運転されている時に発生する内管と外管との温度差にも拘わらず内管と外管が同一に熱膨張されるので、内管と外管との間の密着度の低下がない。 - 特許庁
If the width regulating plate setting center as reference is not correctly set, the envelope 502 passes in a state where it is deviated to the right in figure, so that a temperaturedifference detected by a main thermistor 11d and a sub thermistor 11e on a ceramic heater 11a becomes smaller than a specified value. センタ基準の幅規制板が正しく設定されないと、封筒502は図面上では右に偏って通るので、セラミックヒータ11a上のメインサーミスタ11dとサブサーミスタ11eにより検出される温度差が所定の値より小さくなる。 - 特許庁
To provide a fluid bearing device of high performance and high reliability, and a motor, capable of preventing impairing of temperature characteristic caused by the difference in linear coefficients of expansion between a sleeve and a shaft, and preventing abrasion of bearing faces of both of the sleeve and the shaft. スリーブとシャフトの線膨張係数の違いによる温度特性の悪化を防ぐとともに、スリーブとシャフト両方の軸受面磨耗を防ぎ、高性能で、高信頼性の流体軸受装置およびモータを提供することを目的とする。 - 特許庁
To provide a drum level measuring instrument which can make the densities of water in a reference connecting pipeline and a lower connecting pipeline almost equal to each other by eliminating the temperaturedifference between the water in the pipelines and can improve the accuracy of level measurement in a gas-water separating drum. 基準接続配管内と下部接続配管内における水の温度差をなくして密度を略等しくすることができ、汽水分離用ドラム内の水のレベル計測における精度の向上を図り得るドラムレベル計測装置を提供する。 - 特許庁
To provide an optical wiring resin composition and a photo-electric composite wiring board in which a thermal expansion coefficient difference from an electric wiring board is small, process temperature is close, light propagation loss is small and combination with an electric wiring board is made suitable. 本発明は電気配線板との熱膨張係数差が小さく、かつプロセス温度が近く、かつ光伝搬損失が小さく、かつ電気配線板との複合化に適した光配線用樹脂組成物と、光電気複合配線基板を提供する。 - 特許庁
To provide an acceleration detecting apparatus for accurately detecting an acceleration which is not realized with conventional acceleration sensors because of a deformation difference between a support beam and a resonance body due to a temperature change resulting from different coefficients of thermal expansion of materials of the support beam and the resonance body. 従来の加速度センサーでは、支持梁と共振体とで材質の熱膨張率が異なり、温度変化によって支持梁と共振体とに変形差が生じることにより、加速度を正確に検出できないことが考えられる。 - 特許庁
When a temperaturedifference is generated between the top and bottom surfaces 2a and 2b of the module 2 by heat exchange between the heat source 7 and module 2, the electric power is generated and supplied to the motor of the fan 4 to rotate the fan 4. 熱源部7と熱電変換モジュール2の間の熱交換により、熱電変換モジュール2の上面2aと下面2bの間に温度差が生じることで電力が発生し、この電力がファン4のモータに供給されて該ファン4が回転する。 - 特許庁
To provide a freezer capable of reducing the pressure difference between the high pressure side and the low pressure side in starting of a compressor after a stop without feeding high-temperature/high-pressure gas to an evaporator, and to facilitate the start-up of the compressor. 高温高圧のガスを蒸発機に送り込むことになく、圧縮機停止後の圧縮機の高圧側と低圧側との間の高低圧差が大きい起動時に、その高低圧差を減らして、圧縮機の起動をし易くする冷凍装置を提供する。 - 特許庁
Electromotive force generated by temperaturedifference between the insulating substrates is measured by a voltmeter 23, and a thickness of a wear lining layer is detected on the basis of the measured electromotive force based on the predetermined relationship of the thickness of the wear lining layer 2 and the electromotive force. 絶縁基板間の温度差によって発生する起電力を電圧計23によって測定し、予め求めておいたウエアライニング層2の厚みと起電力との関係から、測定した起電力に基づいて、ウエアライニング層の厚みを検出する。 - 特許庁
A cooling pipe 15 is installed in a steam inlet 11 part in a high-pressure stage 10, and a solenoid valve 16 which opens when the temperaturedifference between the upper half part 2-1 and the lower half part 2-2 of the outer cabin 2 exceeds the specified value is installed in the cooling pipe 15. また、高圧段10の蒸気入口11部にも冷却管15を設け、その冷却管15にも外車室2の上半部2−1と下半部2−2の温度差が所定以上のとき開く電磁弁16を設けてある。 - 特許庁
When the temperatures of the sensor cell 2, pump cell 3, and monitor cell 4 are increased by heating by the heater 6 and then the temperatures are stabilized, temperaturedifference among the sensor cell 2, pump cell 3, and monitor cell 4, is set at 70°C or lower. ヒータ6による加熱によりセンサセル2とポンプセル3とモニタセル4とを温度上昇させた後であってその温度が安定した時点において、センサセル2とポンプセル3とモニタセル4とは、互いの温度差が70℃以下となるよう構成されている。 - 特許庁
To provide a holographic optical information recording regenerating device which maintains a sufficient regeneration signal intensity and enable a stable regeneration of signals with less cross talks even if the optical regeneration wave length is changed according to the difference or temperature change in recording media. 記録媒体の相違や、記録媒体の温度変化によって最適再生波長が変化したときでも、十分な再生信号強度を維持し、クロストークの少ない安定な信号再生が可能なホログラフィック光情報記録再生装置を提供する。 - 特許庁
To provide a control technique for reducing a time difference between timing of switching electric power on fixing temperature control and timing of updating an electric power value, in a fixing device using control comprised of a combination of phase control and wave number control. 位相制御と波数制御を組み合わせた制御を用いた定着装置において、定着温度制御上の電力切換えタイミングと電力値の更新タイミングとの時間差を小さくする制御技術を提供することを目的とする。 - 特許庁
To provide an adsorption material having a high adsorption quantity which is sufficiently different at low humidity and high humidity and capable of continuously performing dehumidification and regeneration by using the difference of adsorption capacity due to temperaturedifference and to provide a dehumidifying method for efficiently and continuously performing the dehumidification of high humidity air by continuously repeating such a dehumidification and regeneration. 低湿度と高湿度とで十分に相違する高い吸湿量を有し、湿度差による吸湿能力の相違を利用して連続的に除湿、再生を行うことができる空調装置用吸着材と、このような除湿、再生を連続的に繰り返すことによって、高湿空気の除湿を効率的に連続して行うことのできる除湿方法を提供する。 - 特許庁
To provide an optical element which can be manufactured at a low cost with a simple manufacturing process, with which an occupied space can be reduced, which reduces preferably the fluctuation band of an optical path difference (phase difference) by a temperature and stress and which functions as a wavelength plate, and to provide an optical device incorporating the same, an optical disk device and a method for manufacturing the optical element. 製造プロセスが簡便で安価に製造可能であり、占有空間を縮小可能であり、好ましくは、さらに温度や応力などによる光路差(位相差)の変動幅が小さい、波長板として機能する機能する光学素子と、これを組み込んだ光学装置、光学ディスク装置、さらに当該光学素子の製造方法を製造する方法を提供する。 - 特許庁
A part of resin is stripped off from the waste containing the metallic member in the resin, an iron member is made to expose outside to be cooled to -50°C or below, and is heated again, and therefore the metal and the resin can be separated using the difference of heat conductivity of the resin and the metal and the difference of expansion and shrinkage ratio at low temperature. 樹脂の中に金属部材が内装された複合廃棄物の表面から一部の樹脂を剥ぎ取り、前記鉄部材を外部に露出させて-50℃以下まで冷却し、引き続き復熱させることにより、樹脂と金属との熱伝導率差、および、低温下における膨張伸縮率差を利用して金属と樹脂とを分離させることを特徴とする金属と樹脂の分離・回収方法。 - 特許庁
To solve a problem wherein a great stress is generated in solder joint of components, because a difference between a linear expansion coefficient of other component and a linear expansion coefficient of a substrate gets large, even when making small a difference between a linear expansion coefficient of a component and the linear expansion coefficient of the substrate, when the components different in the linear expansion coefficients are mounted, in an electronic circuit exposed to a wide temperature range. 広い温度範囲に晒される電子回路においては、線膨張係数の異なる部品が実装されていると、いずれかの部品の線膨張係数と基板との線膨張係数の差を小さくしても、他の部品の線膨張係数と基板との線膨張係数の差は大きくなってしまい、そのはんだ接合には大きな応力が生じてしまう。 - 特許庁
Furthermore, the circuit is configured so that a variable gain amplifier circuit 104 in which a transfer function is proportional to potential difference between control terminals 107, 108, and inversely proportional to potential difference between control terminals 109, 110 is applied with the adjustment voltage of supply voltage fluctuation sensitivity and adjustment voltage of temperature fluctuation sensitivity, thereby reducing the circuit scale while securing the linearity. さらに、伝達関数が制御端子107、108の電位差に比例し、制御端子109、110の電位差に反比例する可変利得増幅回路104に、電源電圧変動感度調整電圧および温度変動感度調整電圧を与える回路構成にすることにより線形性を確保しながら小規模な回路構成を実現している。 - 特許庁
A membrane temperature sensor, a heating means and an exciting means are provided on a cantilever-shaped membrane, wherein the exciting means makes use of warpage due to difference in thermal expansion of two principal layers constituting the membrane while intermittently heated by the heating means of a membrane heater, and a silicon layer and a silicon thermally oxidized film with large difference in their thermal expansion coefficients are used as the two layers. カンチレバ状の薄膜に、薄膜温度センサと加熱手段および励振手段を設けてあり、薄膜ヒータの加熱手段による間欠加熱時の薄膜を構成する主たる二層の熱膨張の違いに基づく反り曲がりを利用して励振手段にしたこと、主たる二層として熱膨張係数に非常に大きな差があるシリコン層とシリコン熱酸化膜を使用する。 - 特許庁
To provide a precast reinforced concrete member capable of reducing the restriction force of a reinforcing rod at the time of shrinkage of concrete during production and advantageous from an aspect reducing the temperaturedifference between the inside and surface of the member at the time of production to the utmost, and its manufacturing method. 製造時におけるコンクリート収縮時の鉄筋の拘束力を低減でき、また、製造時における部材の内部と表面との温度差が極力小さくする上で有利なプレキャスト鉄筋コンクリート部材およびその製造方法を提供すること。 - 特許庁
As a result, the amount of heat transferred to the downstream side electronic components 5 can be increased by increasing the difference in temperature between the components and the refrigerant and the heat transfer coefficient and the heat transfer area of the downstream side fin 11 can be increased according to the newly generated capacity available. この結果、下流側の電子部品5に関して、冷媒との温度差拡大により熱伝達量を高めたり、下流側のフィン11に関して、新たに生じた余力に応じて熱伝達係数や伝熱面積を向上させたりすることができる。 - 特許庁
A photosensitive material is used as the material embedded into the groove part 4 wherein a refractive index temperature coefficient is negative, the difference of the refractive index is also provided in the groove part utilizing the photosensitivity, and whereby an optical waveguide is formed in the traverse direction or in both longitudinal and traverse directions. 1.溝部4に埋め込む屈折率温度係数が負である材料として感光性のあるものを用い、その感光性を利用して溝部にも屈折率差を設け、それにより横方向もしくは縦横両方向に光導波路を形成する。 - 特許庁
A control device 17 calculates stack current density and anode outlet local current density from the measured values of the current sensors 13, 14, when the difference between the stack current density and the anode outlet local current density is changed, the control device set to change the output limitation temperature. 制御装置17は、電流センサ13,14の計測値から、スタック電流密度とアノード出口局所電流密度とを演算し、スタック電流密度とアノード出口局所電流密度との差が変化した場合、出力制限温度を変更して設定する。 - 特許庁
The surface light source device includes a light source body formed with a plurality of light-emitting parts, and at least one or more electrodes formed by partially changing size depending on temperaturedifference (Δt) of the light-emitting parts arranged on each of the light-emitting parts to generate discharging at the light-emitting part. 面光源装置は、複数個の発光部が形成された光源体と、該発光部に放電を起こすために各発光部上に配置されて該発光部の温度差(Δt)に依存して部分的にサイズを変えて形成された一つ以上の電極を含む。 - 特許庁
When infrared irradiation is performed using the heating member 100, time difference of temperature rise is reduced at the time of heating between the electrode pad of the printed circuit board 11 and a solder terminal 21 on the side of the reworked component W and the electronic component W' for replacement. 加熱部材100を用いて赤外線照射を行うことで、プリント回路基板11の電極パッドと、リワーク対象部品W、交換用電子部品W’側のはんだ端子21との間で、加熱時における温度上昇の時間差を減少させる。 - 特許庁
For temperature data signals at a plurality of prescribed temperatures, a data signal DP generated by a time numerical value converting circuit 16 to which each pulse signal Pa, Pb with a phase difference as a reference value t is entered, is stored as a reference data signal DK in a memory 22. メモリ22には、複数の所定温度における温度データ信号に対して、位相差が基準値tの各パルス信号Pa,Pbを入力した時間数値変換回路16が生成するデータ信号DPを基準データ信号DKとして記憶されている。 - 特許庁
To provide a method for joining a viaduct having a high waterproof performance and can flexibly correspond to an enlargement and reduction of a space part in accordance with expansion and contraction of the viaduct by temperaturedifference and a waterproofing layer is not easily deteriorated by protecting the waterproofing layer from damage factor. 高い防水性能を有し、気温差による高架橋の伸縮に伴う空間部の拡縮に柔軟に対応可能であるともに、防水層を損傷要因から保護することにより防水層が劣化しにくい、高架橋の接合方法を提供する。 - 特許庁
With such an arrangement, variation in oscillation frequency due to individual difference of oscillation circuits, time elapse or temperature variation can be reduced, and a pulse generating circuit capable of generating a pulse having an arbitrary width stably through a simple arrangement can be realized. 以上の構成とすることで、発振回路の個体差や、時間経過、温度変化によるによる発振周波数の変動を緩和することができ、簡単な構成で、安定して任意の幅を有するパルスを発生することが可能なパルス発生回路を実現できる。 - 特許庁
The design support device calculates delay sensitivities of voltage and temperature about a clock path included in a clock tree generated in clock tree composition processing (step 23), and adjusts the delay sensitivities of two clock paths such that a difference between the delay sensitivities of the two clock paths is brought close to zero. 設計支援装置は、クロックツリー合成処理(ステップ23)にて生成したクロックツリーに含まれるクロックパスについて、電圧・温度の遅延感度をそれぞれ算出し、2つのクロックパスの遅延感度の差を0に近づけるように、クロックパスの遅延感度を調整する。 - 特許庁