To provide a laminate using a honeycomb structure made of paper, reduced in weight, having high rigidity, low in cost, excellent in recyclability and hard to form the warpage or bending caused by the absorption of moisture in air or the thermal expansion and contraction due to the temperature difference between the upper and under surfaces of the laminate. 紙製のハニカム構造体を用いた積層体であって、軽量で剛性が高く且つ安価であり、リサイクル性に優れると共に、空気中の水分の吸湿や、積層体の表裏面の温度差による熱伸縮などに起因して、反りや曲がりが発生し難い積層体を提供する。 - 特許庁
At this time, a reference voltage is estimated from the command voltage value and the water temperature, the difference between the reference voltage and the command voltage value is found as an air concentration overvoltage target value, an air stoichiometric ratio is calculated based on the air concentration overvoltage target value, so that the air stoichiometric ratio is calculated without using a multidimensional map. この際、指令電圧値と水温から基準電圧を推測し、基準電圧と指令電圧値との差をエア濃度過電圧目標値として求め、エア濃度過電圧目標値に基づいてエアストイキ比を算出することで、多次元マップを用いることなくエアストイキ比を求める。 - 特許庁
To provide a flux composition which does not give rise to cracking in the residual films of a flux after soldering even under the environment of extremes of temperature difference and can form the residual films of the flux exhibiting a moistureproof effect by covering a solder surface and circuit surface and electronic components having the residual films of the flux. 寒暖差の大きい環境下でも、ハンダ付け後のフラックス残さ膜にクラックが発生せず、また、ハンダ表面および回路面を覆って防湿効果を発揮するフラックス残さ膜を形成することのできるフラックス組成物、および該フラックス残さ膜を有する電子部品を提供する。 - 特許庁
Accordingly, at a low temperature, although the housing 65 is contracted larger than the motor case 61 and the rotation shaft 64, a preload relaxing member 81 having a larger thermal expansion coefficient is contracted to absorb difference of a contraction amount and increase of the preload applied to the worm gear 66 and the rotation shaft 64 is suppressed. 従って、低温時には、ハウジング65は、モータケース61、回転軸64等よりも収縮するが、熱膨張係数が大きい予圧緩和部材81が収縮して収縮量の差を吸収し、ウォームギヤ66及び回転軸64に作用する予圧の増加が抑制される。 - 特許庁
To provide an operation control method of a BOG multistage displacement compressor, which can prevent a load (gas load) generated by a pressure difference between a suction gas at a high-pressure stage side and a discharge gas from exceeding an allowable gas load, even if a temperature of a suction gas at a low-pressure stage side is higher than that at a steady operation. 低圧段側吸込ガスが定常運転時よりも高温であっても、高圧段側の吸込ガスと吐出ガスの差圧による荷重(ガス荷重)が、許容ガス荷重を超えることを防止可能なBOG多段容積型圧縮機の運転制御方法を提供する。 - 特許庁
To provide a light source device capable of preventing a creak noise due to a difference in coefficient of thermal expansion between a first optical sheet (e.g. a reflective sheet) and a second optical sheet (e.g. a diffusion sheet) from being generated even when ambient temperature of the device varies, and a display device mounted with the light source device. 装置の環境温度が変化した場合であっても、第1光学シート(例えば反射シート)と第2光学シート(例えば拡散シート)との熱膨張率の相違に起因する軋み音の発生を防止することができる光源装置及び該光源装置を搭載した表示装置を提供する。 - 特許庁
The air-conditioner is equipped with an air-conditioning control unit 14 to emit an operational command for a maximum discharge amount to a variable displacement compressor 8 when the difference in the air temperature between inside and outside the cabin is larger than the prescribed value and an inside-outside air changeover door 43 is changed over from the inner air circulating mode to the outer air suction mode. 車室内及び車室外の気温の温度差が所定値より大きく、かつ内外気切替ドア43が内気循環モードから外気吸込モードに切替えられたとき、可変容量コンプレッサ8に最大吐出量の運転指令を出力する空調コントロールユニット14を備えた。 - 特許庁
By setting the expansion coefficient and the size of the adjusting plate so that the movement of the scanning line by the above deflection and the movement of the scanning line by the difference of expansion amount between the housings 10 and 20 and a drum supporting base 30 are negated each other, the position of a scanning line is arranged to be constant regardless of temperature change. この偏向による走査線の移動と、筐体10,20とドラム支持台30との膨張量の差による走査線の移動とが打ち消し合うよう調整板の膨張率、サイズを設定することにより、温度変化に関わらず走査線の位置を一定に揃えることができる。 - 特許庁
To provide a flow straightening outlet capable of keeping the balance of a water discharge amount as a whole by making the water discharge speed of each nozzle as uniform as possible, and therefore capable of efficiently reducing temperature difference in a water discharge zone even if nozzles cannot be left and right uniformly arranged with respect to the water discharge zone. 放流域に対応して左右均等にノズルを配置できない場合であっても、各ノズルの放水速度をなるべく均等にして、全体として放水量のバランスを保つことができるため、放流域での温度差の低減を効率的に図ることができる整流放水口。 - 特許庁
Before and after a predetermined abnormality determination transitional state (S103), when an EGR gas quantity recirculated by low pressure EGR and an EGR gas quantity recirculated by high pressure EGR change, an absolute value ΔT of a difference in the intake temperature before and after its change is detected (S102). 所定の異常判定過渡状態(S103)の前後において、低圧EGRによって再循環するEGRガス量と高圧EGRによって再循環するEGRガス量とが変化した際に、その変化の前後における吸気温の差の絶対値ΔTを検出する(S102)。 - 特許庁
To provide a steam generator capable of stabilizing a temperature, reducing the stress (strain) caused by heat conductivity and expansion rate of a steam boiler, preventing breakdown and malfunction caused by noise in reading out an AD converter, and coping with difference in voltage outside the country and variation of voltage. 温度を安定させ、スチーム釜の熱伝導率及び膨張率の影響によるストレス(歪)の低減及び破壊を防止し、ADコンバータの読み取り時のノイズによる誤動作を防ぐとともに、国外の電圧の違いや、電圧変動に対応できる蒸気発生装置を提供する。 - 特許庁
The single-stranded DNA hybridization probe used for forming the loop is designed so that a deletion part is adjacent to a position at which the single nucleotide variation is expected to occur, and therefore the single nucleotide variation is detected as a difference of the mobility due to a change of length of the loop by the polyacrylamide gel electrophoresis with a mini-gel at room temperature. ループ形成に用いる1本鎖DNAハイブリダイゼーション・プローブを1塩基変異が予想される箇所に欠失部が隣接するように設計し、1塩基変異をループ長の変化による移動度の差としてミニゲルによる室温のポリアクリルアミド・ゲル電気泳動で検出する。 - 特許庁
An opening adjusting part 115 is provided in the air conditioning unit so that the opening of the front side pressure reducing means 112 is increased with the usage of the difference between an inner pressure of the front side pressure reducing means 112 and an inner pressure of the rear side pressure reducing means 111 when the temperature in the cabin is particularly high. この空調ユニットにおいて、車室内の温度が特に高いとき、フロント側1減圧手段112の内圧とリア側減圧手段111の内圧との差を利用してフロント側減圧手段の開度を増加させる開度調整部115を設けた。 - 特許庁
The ECU 30 calculates the difference between the detected weight of the activated charcoal and the initial weight, determines the kind of the fuel based on the vapor pressure and the vapor temperature, corrects the differential weight according to the kind of the fuel, and further corrects the corrected differential weight based on the vapor pressure. ECU30は、検出される活性炭重量と初期重量との重量差を算出し、ベーパ圧力及びベーパ温度に基づいて燃料種別を判別し、重量差を燃料種別に応じて補正し、更に、補正後重量差をベーパ圧力に基づいて補正する。 - 特許庁
To inexpensively evade troubles that a runner lock pin for automatically cutting a gate through mold-opening is broken and damaged due to the slide defect cauded by the difference of the thermal expansion dependent on the mold temperature during molding to induce a mold crush or the like in a three-sheet structure type mold injection molding mold. 3枚型構造のモールド射出成形金型において、ゲートを型開きにより自動切断を行うためのランナーロックピンが、成形時の金型温度による熱膨張差により摺動不良により折れ、破損し金型潰れ等によって引き起こされる不具合を低コストで回避させる。 - 特許庁
In a mercury-free ceramic metal halide lamp (1), any one of halides of Zn, Al, Ga, In, and Sn is encapsulated, and a temperature difference between an upper part and a lower part of the light-emitting tube surface is restricted to 200°C or lower by disposing a center of electrodes in a lower side of a center of a light-emitting part. 無水銀セラミックメタルハライドランプ(1)には、Zn、Al、Ga、In、Snのいずれかのハロゲン化物が封入され、電極間中心を発光部中心よりも下側に配置することにより、発光管表面温度の上部温度と下部温度の差を200℃以下に抑制する。 - 特許庁
To provide a reinforced concrete member capable reducing the restriction force of a reinforcing rod to the utmost at the time of shrinkage of concrete to the utmost, capable of making the temperature difference between the inside and the surface of a member as small as possible at the time of curing of concrete and advantageous from an aspect preventing a crack while reducing cost. コンクリート収縮時の鉄筋の拘束力を極力低減でき、また、コンクリート硬化時における部材の内部と表面との温度差が極力小さくでき、コストを低減しつつひび割れを防止する上で有利な鉄筋コンクリート部材を提供すること。 - 特許庁
To provide a wine storage which can give a sense of security at placement of wine, by preventing the contact of the fellow bottles on a wine shelf within a storage, and suppressing the peeling of a label and the propagation of mold, and minimizing the difference of temperature distribution between each wine shelf and the next within the storage, and besides, preventing the fall of the wine shelf. 庫内室ワイン棚におけるボトル同士の接触を防止し、ラベルの剥離及びカビの繁殖を抑え、庫内室各ワイン棚間の温度分布差を最小限に出来、かつワイン棚の落下を防止でき、ワイン載置時の安定感を与えるワイン保蔵庫を提供する。 - 特許庁
To provide a joint structure having no crack on the surface even if there is no variation in a joint width, a joint processing material used for executing work to the joint structure and a joint processing method capable of facilitating construction work, getting along with few construction manhour and allowing expansion and contraction of an exterior wall board by the difference of temperature. 施工し易く、施工工数が少なくてすみ、しかも、寒暖の差によって外壁ボードが膨張収縮し、目地幅が変化しても、表面にクラックの入らない目地構造と、この目地構造に施工するために使用する目地処理材や目地処理方法を提供すること。 - 特許庁
Provided that a room pressure control device 1A is constructed as such, the interior of the room 61 is set to arbitrary pressure owing to a difference between the supply air amount and the exhaust air amount, and the air amount is varied in response to a thermal load in the room, whereby it is possible to keep the temperature in the room unchanged. このように室圧制御装置1Aを構成すれば、給気風量と排気風量の差によって室61の内部を任意圧力に設定するとともに、室内の熱負荷に応じて風量を変動させ、前記室内の温度を一定に保つことが可能になる。 - 特許庁
To provide a thermoelectric element which keeps proper thermal contact with a heat source and an object to be cooled and can easily make electrical connections with external circuits, without impeding the thermal contact as a small-sized thermoelectric element which is usable for temperature difference power generation and local cooling of portable information equipment. 携帯用情報機器の温度差発電や局所冷却などに利用できるような小型の熱電素子に関して、熱源や冷却対象物への熱接触を良好に保つとともに、熱接触を妨げずに外部回路への電気接続を容易に行える熱電素子を提供する。 - 特許庁
Further, at a high temperature, although the housing 65 is expanded larger than the motor case 61 and the rotation shaft 64, the preload relaxing member 81 having the larger thermal expansion coefficient is expanded to absorb difference of an expansion amount and reduction of the preload applied to the worm gear 66 and the rotation shaft 64 is suppressed. また、高温時には、ハウジング65は、モータケース61、回転軸64等よりも膨張するが、熱膨張係数が大きい予圧緩和部材81が膨張して膨張量の差を吸収し、ウォームギヤ66及び回転軸64に作用する予圧の減少が抑制される。 - 特許庁
In a casting process under a high temperature, even when a large clearance is caused by a difference of thermal expansion coefficient between the main cylindrical part 14 and the holder part 30, the main cylindrical part 14 is fixed to the holder part 30 by pressurizing the main cylindrical part 14 via the movable blocks 34 and 36. 高温下での鋳造工程において、主筒部14とホルダー部30の間に、熱膨張係数差に起因して大きなクリアランスが生じる場合であっても、可動ブロック34,36を介して主筒部14を押圧することで、主筒部14をホルダー部30に固定できる。 - 特許庁
To solve a problem that the indoor environment is degraded attributable to the draft caused by the upper and lower temperature difference during the winter time, door opening/closing troubles and wind noise occur in a high-rise building, and countermeasures of directly and effectively reducing the draft have not been taken. 高層建築物においては、冬季の上下温度差によるドラフトに起因して室内環境が低下したり、ドアの開閉障害や風切り音を発生することがあるが、このようなドラフトを直接的に有効に低減することのできる対策は、従来行われていない。 - 特許庁
To enhance analyzing sensitivity and analysis accuracy, regardless of the presence of a coexistent substance, by making a target element rapidly convert to a chemical substance stable in a high density and high-concentration state at a low temperature to evaporate the same, regardless of the difference in evaporation behavior and suppressing the lowering of loss and transfer efficiency. 蒸発挙動の差異に関係なく、目的元素を低温かつ速やかに高密度高濃度で安定な化学物質に変換し気化させ、かつ、損失及び移送効率の低下を抑制して、共存物の存在にかかわらず分析感度及び分析精度の向上を実現する。 - 特許庁
To provide an air-conditioning control system capable of providing a sleeping environment to allow a sleeper to have a good sleep regardless of individual difference of sleepers by performing the different temperature controls between a time of non-REM sleeping condition and a time of a REM sleeping condition without time lag at the boundary of both times. 就寝者の個体差に依らず、NONREM睡眠状態の時期とREM睡眠状態の時期とで異なる温度の制御を、両者の境界でタイムラグ無く行って、就寝者が安眠できるような就寝環境を実現できる空調制御システムを提供する。 - 特許庁
To provide a ring magnet, which has little difference between the turning torque of the magnet and the turning torques of alnico and ferrite magnets even though the magnet is combined with the alnico and ferrite magnets and has a sufficient temperature dependence from the viewpoint of the performance of an electron beam adjusting device, and to provide a method of manufacturing the ring magnet and the electron beam adjusting device using that magnet. アルニコ系、フェライト系のマグネットと組み合わせても回転トルクの差が少なく、電子ビーム調整装置の性能上充分な温度依存性をもったリング状マグネットならびにその製造方法、および該マグネットを使用した電子ビーム調整装置を提供する。 - 特許庁
By performing dry etching in a dry etching step, while controlling the temperature of the lower electrode of an etching device equal with or lower than 10°C, volatilization of a subproduct is suppressed, more stable sidewall protection effect can be obtained, and a uniform etching shape reducing the working shape difference between a coarse portion and a tight portion can be obtained. 前記ドライエッチング工程にて、エッチング装置の下部電極温度を10℃以下に制御しドライエッチングを行うことにより、副生成物の揮発を抑制し、より安定した側壁保護効果が得られ、疎部、密部における加工形状差の少ない均一なエッチング形状が得られる。 - 特許庁
To provide a screw compressor that can prevent a gate rotor from biting into a screw rotor with a simple configuration, reduce wear amount of the gate rotor, and prevent capacity lowering of compressor, even if a gate rotor deflects due to temperature difference between casing and screw rotor during the operation of compressor. 圧縮機の運転中に、ケーシングとスクリューロータとの温度差により、ゲートロータが撓んでも、簡単な構成で、ゲートロータのスクリューロータへの食い込みを防止して、ゲートロータの磨耗量を低減させて、圧縮機の能力低下を防止するスクリュー圧縮機を提供する。 - 特許庁
To enable reliable wiring patterning by eliminating or reducing linear thermal expansion coefficient between a transfer mold and a substrate, and thus by eliminating a problem of expansion difference between the transfer mold and the substrate when they are heated up to a predetermined temperature in an embossing process. 転写金型と基板との間の線熱膨張係数の差をなくするか或いは減少して、エンボス加工の際に転写金型と基板とを所定温度まで加熱しても両者間の膨張差による問題を解消し、信頼性のある配線パターニングを可能にする。 - 特許庁
This piping cover 1 for covering a boiler piping (or a water cooling piping) 2 is thermally deformed by a temperature difference between during the operation and during a stop of operation, and materials adhered during the operation is peeled by the thermal deformation during a stop of operation. ボイラー配管(又は水冷配管)2に覆われて使用される配管カバー1であり、運転中と運転休止中の温度差により熱変形し、運転中に付着した付着物を、運転休止時に前記熱変形により剥離させることを特徴とする配管カバー1。 - 特許庁
A step structure is formed on lens surface 11 of the objective lens 10, the action of the step structure and arrangement of satisfying a predetermined magnification correct a spherical aberration that occurs due to a wavelength difference and a change in the thickness of a protective layer, and suppress the amount of a spherical aberration due to a temperature change. 対物レンズ10のレンズ面11には段差構造が形成され、その作用と所定の倍率を満たす配置とにより、波長の違いと保護層の厚さの違いにより生じる球面収差を補正すると共に、温度変化による球面収差の発生量を小さく抑える。 - 特許庁
To provide a processing method for a planographic printing plate capable of always achieving high ink acceptability and high printing resistance independently of difference in sensitization temperature and time with respect to a method for developing a printing plate in which a photographically formed silver halide image is applied as lipophilicity and ink acceptability. 写真的に形成されたハロゲン化銀像を親油性、インキ受容性として応用する印刷版の現像処理方法に於いて、感脂化処理の処理温度、処理時間の差異に拘わらず、常に高いインキ受容性と高い耐刷性を実現できる平版印刷版の処理方法である。 - 特許庁
Molten glass 40 in a molten state is caused to fall in the form of liquid line by its own gravity from each of plurality of flow-out ports 33a, 33b, 33c and 33d and is caused to stay in a lower mold 11, thereby temperature difference between the central part and the peripheral part of a gob of molten glass 40 is made small. 複数の流出口33a,33b,33c,33dのそれぞれから溶融状態の溶融ガラスを自重により液線状に落下させて、下型11に溶融ガラス40を滞留させることにより、溶融ガラス40の塊の中心部分と周辺部分との温度差を小さくする。 - 特許庁
In the center axis 7, at least a site contacted with the outer circumference against the filling powders 26 is constituted of a metal material in which from room temperature to 500°C, difference of coefficient of thermal expansion from a material constituting the insulating insulator 2 is within a range of 2.0×10^-6 (1/K). 中軸7のうち、少なくとも充填粉末26に対して外周面が接触する部位が、常温から500℃において絶縁碍子2を構成する材料との線膨張係数の差が2.0×10^-6(1/K)以内となる金属材料により構成される。 - 特許庁
The duct 2 is provided with a heating device 3 for supplying heat to air flowing within the first communication pipe 2a and the second communication pipe 2b or absorbing heat from the air to produce a temperature difference between air blown out from the first outlet 2a2 and air blown out from the second outlet 2b2. ダクト2には、第一連通管2aと第二連通管2bを流れる空気に熱を供給または空気から熱を吸収して第一吹出し口2a2から吹出される空気と第二吹出し口2b2から吹出される空気に温度差を生じさせ得る熱装置3が設けられている。 - 特許庁
In the thermoelectric conversion/release part 40 disposed between the heat insulation part 31 and the bellows 36, the exhaust heat is converted into electricity by a thermoelectric element layer 41 according to a temperature difference between a heat insulation part 31 side and a bellows 36 side and is released to the outside through an electric resistor 43. そして、断熱部31とベローズ36との間に配設された熱電変換放出部40によって、断熱部31側とベローズ36側との温度差に応じて熱電素子層41が排気の熱を電気へ変換して電気抵抗器43を介して外部へ放出する。 - 特許庁
A sensor output signal Vs to which correction amount of sensitivity of the vibrator to temperature change is added continuously, and a sensor inversion output signal Vs bar are selected by a phase difference detecting means 20 of an angular velocity detecting part 40, and outputted to a first and a second integration smoothing circuits 31A, 31B. 温度変化に対する振動子の感度の補正量を連続的に加味したセンサ出力信号Vs及びセンサ反転出力信号Vsバーを、角速度検出部40の位相差検出手段20で選択して第1および第2の積分平滑回路31A,31Bに出力する。 - 特許庁
A glass layer 3 is melted by irradiation of a laser beam L, and a temperature difference wherein the temperatures of principal surfaces 40a, 50a on the side of the glass layer 3 become higher than the temperatures of principal surfaces 40b, 50b on the opposite side of the glass layer 3 arises at parts along a planned weld region R at respective glass substrates 40, 50. レーザ光Lの照射によってガラス層3が溶融し、各ガラス基板40,50における溶着予定領域Rに沿った部分に、ガラス層3側の主面40a,50aの温度がガラス層3と反対側の主面40b,50bの温度よりも高くなる温度差が生じる。 - 特許庁
Since the sampling system is common to the illuminating light 2 of each color, the individual difference of the sampling system can be eliminated; and even if the LED 11r-11b of each color is varied in the temperature coefficient, or the like, the projector 1 can display an image has color tone which remains unchanged. サンプリング系統を各色の照明光2に対して共通にしたので、サンプリング系統の個体差を排除することができ、各色のLED11r〜11bに温度係数のばらつきなどがあっても、色合いの変わらない画像が表示できるプロジェクタ1を提供できる。 - 特許庁
To provide an electrode for a discharge lamp which will not fall off from an electrode core pole, a gap being prevented from occurring between a recess and the electrode core pole even if temperature difference arises between the electrode and the electrode core pole, or to provide an electrode for a discharge lamp which will not be broken, nor an electrode core pole, during press fitting. 電極と電極芯棒の間に温度差が生じても、凹部と電極芯棒の間に隙間が生じず、電極芯棒から電極が抜け落ちない放電ランプ用電極、あるいは圧入時に電極芯棒や電極の割れない放電ランプ用電極を提供すること。 - 特許庁
To provide a thermionic generation device which can wider a temperature difference, which is applied to both ends of thermionic elements and output much higher power and a generated output by more raising a heat transfer efficiency from a heat-collecting side member to the thermionic elements and/or from the thermionic element to a cooling side member. 集熱側部材から熱電素子まで、および/または、熱電素子から冷却側部材まで、熱伝達効率をより一層向上させることにより、熱電素子の両端にかかる温度差を大きくとることができ、発電出力がより一層大きい熱電発電装置を提供する。 - 特許庁
To solve a problem that since a probe optical path is separated spatially from a reference optical path, when temperature distribution, refractive index distribution by fluctuation of air or the like or a mechanical vibration is generated, an optical path difference is fluctuated between both optical paths to generate a measurement error, in a displacement measuring device using optical interference. 光干渉を用いた変位計測装置において、プローブ光路と参照光路とが空間的に分離しているため、空気の揺らぎ等による温度分布や屈折率分布、あるいは機械振動が生じた場合、両光路間で光路差が変動し、測定誤差となってしまう。 - 特許庁
To provide a sealing structure for a lead wire leader having excellent sealability without bringing about an electrical energization fault at the leader and without bringing about a respirating operation even if a pressure difference between an interior and an exterior occurs due to a temperature change, and further provide a method for sealing the lead wire leader. リード線引き出し部において、電気的導通不良が発生することがなく、しかも、温度変化による内外の圧力差が生じても、呼吸作用が発生せず、シール性に優れたリード線引き出し部のシール構造およびリード線引き出し部のシール方法を提供する - 特許庁
This spindle can be manufactured using the inner ring spacer 4_in and the outer ring spacer 4_out provided with the heat transfer fins 5_in, 5_out instead of the conventional inner ring space and the outer ring space of the spindle, so that a difference in temperature between the inner and outer rings of the angular ball bearing 4_out can be easily reduced. また、本発明のスピンドルは、従来のスピンドルの内輪間座及び外輪間座に代えて、伝熱フィン5_in、5_outが形成された内輪間座4_in及び外輪間座4_outを用いるだけで製造することができ、その結果、アンギュラ玉軸受4_outの内外輪温度差を容易に小さくすることができる。 - 特許庁
To provide a suction device for ejecting a resin molded product capable of certainly enhancing the quality and molding yield of the resin molded product by reducing the temperature difference between the resin molded product and a suction pad at the time of suction of the resin molded product to avoid the occurrence of a suction mark or warpage. 樹脂成形品吸着時における樹脂成形品と吸着パッドとの温度差を小さくして、吸着痕やソリの発生を回避することで、樹脂成形品の品質および成形歩留を確実に向上させることができる成形品取出用の吸着装置を提供する。 - 特許庁
The essential oil is extracted by freezing a liquid raw material 1 containing the essential oil having a melting point of <0°C at a freezing temperature between 0°C to the melting point of the essential oil, defrosting the frozen raw material 1 and utilizing the difference of the specific gravity between the defrosted essential oil and raw material potion 7. 融点が0度よりも低い精油を含む液状の原料1を、0度から精油の融点よりも高い温度までの間の凍結温度で凍結させ、凍結した原料1を解凍し、解凍された原料分7と精油との比重差を利用して精油を抽出するようにしている。 - 特許庁
A data signal to be applied to an element driving transistor Tr2 which controls an electric current flowing through an EL element is adjusted in accordance with use environment such as external light luminance, temperature and deterioration extent of the EL element, and the power source voltage difference (CV margin) between a driving power source and a cathode power source is adjusted. 外光輝度や温度、EL素子の劣化程度などの使用環境に応じ、EL素子に流す電流を制御する素子駆動用トランジスタTr2に印加するためのデータ信号を調整し、かつ、駆動電源とカソード電源との電源電圧差(CVマージン)を調整する。 - 特許庁
When a thermal equalization member 68 is brought into contact with a fixing belt 64, an image forming apparatus changes a printing state when the thermal equalization member 68 is in contact with the fixing belt 64 in accordance with the difference in temperature between a paper feeding part of the fixing belt 64 and the thermal equalization member 68. 画像形成装置は、熱均一化部材68を定着ベルト64に接触させる場合には、定着ベルト64の通紙部の温度と熱均一化部材68の温度との温度差に応じて、熱均一化部材68の定着ベルト64への接触時の印刷状態を変更する。 - 特許庁
The raw material for chemical vapor deposition consists of the tantalum compound expressed by formula (I), a titanium compound expressed by formula (II) and an organic solvent used at need, and in which the difference in thermal oxidation decomposition temperature between the tantalum compound and the titanium compound is <50°C in terms of an absolute value. 下記一般式(I)で表されるタンタル化合物、下記一般式(II)で表されるチタニウム化合物及び必要に応じて用いられる有機溶媒からなり、上記タンタル化合物と上記チタニウム化合物との熱酸化分解温度の差が絶対値で50℃未満である化学気相成長用原料。 - 特許庁