「Drop-In」を含む例文一覧(7281)

<前へ 1 2 .... 123 124 125 126 127 128 129 130 131 .... 145 146 次へ>
  • To provide: a metal outer package case material which has little elution of metal in aging process at the time of manufacture of a lithium ion battery, and as a result, has little voltage drop of lithium ion battery after aging; a metal outer package case; and a lithium ion battery using the same.
    リチウムイオン電池製造時のエージング工程で金属溶出が少なく、この結果、エージング後のリチウムイオン電池の電圧低下が少ない金属外装ケース用素材、金属外装ケースおよび該金属外装ケースを用いたリチウムイオン電池を提供する。 - 特許庁
  • The sealing agent for a liquid crystal one-drop-fill method contains a (meta)acrylate compound having a structure represented by general formula (1), wherein the (meta)acrylate compound accounts for 10 to 70 wt.% of a curable resin component included in the agent.
    下記一般式(1)で表される構造を有する(メタ)アクリレート化合物を含有する液晶滴下工法用シール剤であって、含有する硬化性樹脂成分の10〜70重量%が前記(メタ)アクリレート化合物である液晶滴下工法用シール剤。 - 特許庁
  • Since conventional fuels have a poor combustion rate and a large specific gravity, the fuels drop on the ground as being ignited, and there often occur accidents of a liquid alone dropping in an incomplete combustion and the leakage of the fuel, but these problems can be solved by the injection into the cassette-type cylinder.
    従来の液体燃料は、燃焼率が悪く比重が重い為に着火したまま地面へ落ち、不完全燃焼で液だけが落ちる事故や燃料漏れも多くあったが、このような問題をカセット式ボンベに注入する事で解決できる。 - 特許庁
  • To enhance the quality of a recording image by letting fly uniform liquid droplets from each heating resistor by forming a gate electrode and the heating resistor from polycrystal Si at the same time and suppressing the voltage drop in a power supply wiring.
    ゲート電極と発熱抵抗体とを多結晶Siで同時に形成すると共に、電源配線での電圧降下を抑制し、各発熱抵抗体から均一な液滴を飛翔させ、記録画像の画質の向上を図った液体噴射記録装置を提供する。 - 特許庁
  • While the ink chamber 114 is in the contraction condition by the displacement of one piezoelectric element 116a after the ejection of an ink drop is started by one piezoelectric element 116a, the other piezoelectric element 116b is displaced to further contract the ink chamber 114.
    一方の圧電素子116aによってインク滴の吐出を開始したのち、この圧電素子116aの変位によってインク室114が収縮状態にあるときに、他方の圧電素子116bを変位させてインク室114をさらに収縮させる。 - 特許庁
  • An average voltage generating circuit 8 generates the average voltage from the voltage 7 and a voltage showing the largest voltage drop from the voltage 7 among the DC voltage in the vicinities of the loads 8, 9, and 10 and the voltage 7.
    平均電圧生成回路6は、負荷8,負荷9および負荷10近傍のDC電圧値の中でDC/DCコンバータ出力部電圧7からの電圧降下が一番大きい最低電圧と、DC/DCコンバータ出力部電圧7との平均電圧を生成する。 - 特許庁
  • To obtain an aqueous removable adhesive which does not drop a label naturally from paper, corrugated board-like rough surface, a nonpolar adherend such as a polyethylene or a polypropylene, does not increase adhesive strength even in an adherend made of a metal and takes sanitation nature into consideration.
    紙に対してはもちろんダンボールの様な粗面やポリエチレン、ポリプロピレンの様な非極性被着体に対してラベルが脱落せず、金属製の被着体でも接着力が増大せず、且つ衛生性に配慮した水性再剥離型粘着剤を提供する。 - 特許庁
  • To provide a two stage vacuum pump capable of suppressing drop of exhaust efficiency and rise of pressure at an intermediate connection part, and reducing rise of drive torque in the two stage vacuum pump having a first vacuum pump and a second screw type vacuum pump connected thereto.
    第一の真空ポンプと第二のスクリュー式真空ポンプとを連結した2段真空ポンプにおいて、排気効率の低下と中間連結部における圧力上昇とを抑制し、駆動トルクの上昇を低減することのできる2段真空ポンプを提供する。 - 特許庁
  • The vegetation maintenance material includes the vegetation bag containing vegetation base and plant seeds, and utilizes fibrous materials and hydrated hardening material, and consequently the vegetation base and plant seeds are hard to drop in constructing on an uphill.
    植生基材及び植物種子を収容した植生袋からなる植生補修材料において、繊維状材料や水和硬化材料を用いることで、傾斜地に施工した場合でも植生基材および植物種子が脱落しにくい植生補修材料。 - 特許庁
  • The alternating current component signal is rectified by a rectifying diode D1 inside a reference voltage generating circuit 5, followed by smoothing, so as to generate a reference voltage Vref low in its voltage by a forward-directional voltage drop Vf of the diode D1 compared with a high level voltage thereof.
    この交流成分信号は基準電圧生成回路5内の整流用ダイオードD1で整流され、平滑化されると、そのハイレベル電圧よりダイオードD1の順方向降下電圧Vf分だけ低い基準電圧Vrefが生成される。 - 特許庁
  • To provide a tip member made of ceramic with which fall-off in a piercing process is easily prevented without bringing about strength drop and furthermore deviation of its axial line from the axial line of the main body of a plug is easily prevented and a plug for manufacturing seamless tubes using the same.
    強度の低下を招くことなく、穿孔過程での抜け落ちが容易に防止され、さらにはその軸線がプラグ本体の軸線に対してずれることが容易に防止されるセラミック製先端部材、及びこれを用いた継目無管製造用プラグを提供する。 - 特許庁
  • To develop a method for producing dimethyl ether, by which methanol being the by-product of dimethyl ether synthesis reaction and a medium oil of catalyst slurry contained in a product gas taken out from a reactor are returned to a reaction system and rapid drop of reaction yield caused by the return of methanol and the medium oil can be controlled.
    ジメチルエーテル合成反応の副生成物であるメタノールや反応器から取り出される生成物ガスに含まれる触媒スラリーの媒体油を反応系に返送し、それによる反応収率の急速な低下を抑制できる方法を開発する。 - 特許庁
  • To provide a recording method capable of high speed printing in which an ink drop can be shot at a normal dot position without altering the ejection timing of a recording element regardless of single pass printing or multipass printing.
    シングルパス印字であるか、またはマルチパス印字であるかに拘わらず、記録素子の吐出タイミングを変更することなく正規のドット位置上にインク滴を精度良く着弾させることができるともに、高速印字を行うことが可能な記録方法を提供する。 - 特許庁
  • In a motorcycle which is provided with an ECU to control the output of its power source and connects an acceleration sensor to this ECU, the wheelie condition is detected from the detected output of the acceleration sensor and controlled to drop the output of the power source.
    自動二輪車の動力源の出力制御を行うECUを備え、該ECUに加速度センサーを接続した自動二輪車において、前記加速度センサーの検出出力からウィリー状態を判別し、前記動力源の出力を低下するように制御する。 - 特許庁
  • The drop drawing is performed only in start opening prize winning where variation display of a performance pattern is performed when lapse time t after a game state changes from a normal game state to a probability variable game state is t1≤t≤t2.
    遊技状態が通常遊技状態から確変遊技状態に変化してからの経過時間tがt1≦t≦t2である期間において、演出図柄の変動表示が行われることになる始動口入賞時にのみ転落抽選を行うようにする。 - 特許庁
  • This increases a potential gradient in a space between the second intermediate electrode 23 and the anode 26 more than a potential gradient caused by the voltage drop, thereby accelerating electrons (plasma) drawn out from the plasma generating source to draw out them long into the film forming space.
    これにより、第2中間電極23と陽極26との間の空間の電位勾配を、電圧降下による電位勾配より大きくすることができるため、プラズマ発生源から引き出された電子(プラズマ)を加速して、成膜空間に長く引き出すことができる。 - 特許庁
  • To provide a nonaqueous electrolyte battery which is prevented from a voltage drop at discharge and improved in its discharge property, including a positive electrode made of fluorocarbon and a negative electrode made of materials which can discharge lithium ions such as lithium metal or lithium alloy.
    正極にフッ化炭素を用い、負極にリチウム金属またはリチウム合金などのリチウムイオンを放出可能な材料を用いた非水電解液電池において、放電時の電圧降下を抑制し、放電特性の向上した非水電解液電池を提供する。 - 特許庁
  • To provide an impregnated cathode capable of restraining the drop of the quantity of impregnation of an electron emission substance into a porous base body, and of providing high electron emission, in an impregnated cathode using the electron emission substance containing scandium or a scandium compound.
    スカンジウムもしくはスカンジウム化合物を含有した電子放射物質を用いた含浸型陰極において、多孔質基体中への電子放射物質の含浸量低下を抑制し、高い電子放射を得ることができる含浸型陰極を提供する。 - 特許庁
  • This is inevitable because stock prices are determined by the market. However, it is not desirable that stock prices should continue to drop while producing an unduly negative impact in the absence of buyers due to overly strong selling pressure.
    これは、株の値段は市場で決まるということで、しようがないことなんですけれども、あまり売り方が強くて買い方が誰も現れないという状況ですと、必要以上の影響を与えながら株価が下がっていくという現象は決して好ましくない。 - 金融庁
  • To provide a package for keeping the freshness of loquat, excellent in preservability for loquat, and having a fine appearance and capable of preventing decay and mold of loquat caused from a wet part through preventing drop of water from adhering to the internal surface of a film and the surface of loquat.
    ビワの保存性が良好であり、フィルム内面とビワ表面への水滴の付着を防止することで、包装体の外観が美しく、かつ水濡れ部分より生じるビワの腐敗、カビを防止することが可能なビワの鮮度保持用包装体を提供する。 - 特許庁
  • To provide an image forming apparatus which has a heating means to receive power supply from a primary side of a power supply device and in which the standby time is shortened by supplying sufficient electric power to the heating means while the fault due to voltage drop of commercial electric power is surely suppressed.
    電源装置の1次側から電力供給を受ける加熱手段を有する画像形成装置において、商用電力の電圧低下による不具合を確実に抑えつつ加熱手段に充分な電力を供給して待機時間を短縮化する。 - 特許庁
  • To prevent a film member from being broken by interposing it between a plate member and a rib by the vibration, the drop, etc. at its physical distribution time about an ink tank which an energizing force is operated on a flexible film member through a plate member, and is made into vacuum state at ink in a film member.
    可撓性フィルム部材に板部材を介して付勢力を作用させてフィルム部材内のインクに負圧状態とするインクタンクについて、その物流時の振動や落下などによって、フィルム部材が、板部材とリブとの間に挟まれて破れる。 - 特許庁
  • Lids 6 and 7 are attached to the tips of a suction pipe 2 and discharge pipe 3 of a kerosene pump 1, and a plurality of suction holes 4 and discharge holes 5 are provided at the pipe trunks in proximity over the lids 6 and 7 so that spaces to be used as drop sumps 8 and 9 are formed.
    灯油ポンプ1の吸入パイプ2及び排出パイプ3の先端に、蓋6,7を取り付け、該両パイプの、蓋6,7の上方近接胴部に複数の吸入口4及び排出口5を設けて、滴溜まり8,9となる空間部を形成するものである。 - 特許庁
  • In the event that the anchor bolts securing the one track beam 20L to the post 10 are damaged by a large earthquake making the track beam 20L likely to move past the post 10L and drop, the wire rope 46 pulls the track beam toward the other bearing 30R, preventing the track beam from dropping.
    これに寄れば、一方の軌道桁20Lを支柱10に固定するアンカーボルトが大地震で損傷し、軌動桁に20Lが支柱10Lを移動して落下しようとすると、ワイヤーボルト46で他方の支承30Rに引っ張られ、落下できない。 - 特許庁
  • To suppress cancellation or reduction of a predetermined fuel economy improvement effect in relation to change of compression ratio by intentionally making response of target compression ratio to demand compression ratio dull when the demand compression ratio rises and suppress and eliminate drop of reliability and durability of a mechanism and an actuator controlling compression ratio due to operation of excessive compression ratio change.
    圧縮比を頻繁に変更すると、圧縮比を変更するためのエネルギー損失によって、本来の目的である燃費向上効果が目減りするとともに、圧縮比を操作する機構・アクチュエータの耐久性・信頼性の低下を招く。 - 特許庁
  • This overdischarging preventer of a battery pack detects the voltage Vn of each battery of a battery pack constituted by connecting a plurality of batteries in series (step S104), and obtains the lowest voltage Vmin (step S106, and also obtains the maximum drop rate dVmax and sets a threshold Vβ (step S112).
    複数の電池を直列に接続して構成される集合電池の各電池の電圧Vnを検出し(ステップS104)、最低電圧Vminを求めると共に(ステップS106)、最大降下率dVmaxを求めて閾値Vβを設定する(ステップS112)。 - 特許庁
  • In this butter beater, a fixed scoop part 3 is doubled, and the grip part is provided with the clip 2, whereby a turning scoop part 4 is caused to make turning motion by the action of a spring so that material can be held between the scoop parts not to drop.
    バタービーターの固定すくい部3にもう一枚重ね二枚重ねにして柄部1にクリップ2を設けたことによってバネの働きで回動すくい部4が回動運動するため材料を挟み込むようにして落下しないように使用出来るバタービーターである。 - 特許庁
  • This alarm device of the blast type ion generator is provided with: a wind-speed sensor 12 for detecting the speed of wind sucked in a suction port; and a blower alarm signal generation circuit 25 for inputting output from the wind-speed sensor 12 to generate a blower alarm signal based on its output drop.
    吸い込み口に吸い込まれる風速を検出する風速センサ12と、この風速センサ12からの出力を入力し、その出力低下に基づいて送風機警報信号を発生する送風機警報信号発生回路25とを備える - 特許庁
  • A value obtained by adding the estimated value of a voltage drop by a series resistance 2324Y or the like to the voltage applied to the charging roller 231Y or the like is stored in a lookup table 105 to set an output voltage of the DC voltage generator 2325Y or the like.
    各直流電圧発生器2324Y等の出力電圧を定めるためのルックアップテーブル105には帯電ローラ231Y等への印加電圧に直列抵抗2324Y等による電圧降下の見積もり量を加算した値が格納されている。 - 特許庁
  • To provide a tire air pressure drop alarm method, a device, and a tire pressure reduction evaluation program which detect with ease that four wheels are decompressed at the same time even when a vehicle is not in a state of rotation under the travelling condition that the vehicle has driving force.
    車両が駆動力を有する走行状態で、旋回状態でない場合でも4輪が同時に減圧していることを、しかも簡単に検出するタイヤ空気圧低下警報方法および装置、ならびにタイヤ減圧判定プログラムを提供する。 - 特許庁
  • A plurality of pressure chambers are divided into three sets of two chambers apart, phase of the sets is changed to phase A, phase B and phase C, for example, and an ink drop ejection pulse is outputted in the order of A1 (phase A) to B1 (phase B) to C1 (phase C) to A2 (phase A) to....
    複数の圧力室を2個置きの3組に分割し、組毎に位相を、例えば位相A、位相B、位相Cと変化させてインク滴を吐出させる吐出パルスをA1(位相A)→B1(位相B)→C1(位相C)→A2(位相A)→…の順に出力する。 - 特許庁
  • To provide a wet type developing device for a plate making device capable of preventing a drop of the developer from a developing part electrode and squeezing rollers from scattering on a peripheral part as a splash, and restraining the contained developer from flowing over the peripheral part in spite of rapidly moving a recovering vessel from outside.
    現像部電極や絞りローラから滴下する現像液が周囲に飛沫として飛散することがなく、外部から回収槽を急速に動かしても収容された現像液が周囲に溢れることがない製版機の湿式現像装置を得るにある。 - 特許庁
  • To reduce fuel consumption when lowering a heavy load and to prevent a drop of operating speed of the other hydraulic actuator when interlocking the lowering of the heavy load with the other hydraulic actuator in a construction machine comprising a hydraulic cylinder for moving the heavy load up and down.
    重量物を上下動させる油圧シリンダを備えた建設機械において、重量物の下動時に燃費低減を図る一方、重量物の下動と他の油圧アクチュエータとの連動時に、他の油圧アクチュエータの作動速度が低下してしまうことを防止する。 - 特許庁
  • A current, flowing in the storage, is determined by deducing the current value measured with the current measurement instrument 3 from a constant-current value, provided from the power source 5 of the alternating current of the constant current, and then the internal resistance of the battery is determined from this current and the voltage drop measured with the voltage measuring instrument 6.
    そして、定電流交流電源からの定電流値から電流測定器で測定した電流値を引いて蓄電池に流れる電流を求め、これと電圧測定器で測定した降下電圧値とから蓄電池の内部抵抗を求める。 - 特許庁
  • To provide a structure of magnetic tunnel junction which is subjected to heat treatment without an increase in the tunnel resistance value and a drop of the MTJ breakdown voltage, and also to provide a method for encapsulating magnetic tunnel junction for providing the same, and a method for forming a magnetic device comprising the same.
    トンネル抵抗値の増加やMTJ破壊電圧の低下を伴うことなく熱処理に晒すことができる磁気トンネル接合構造、これを実現し得る磁気トンネル接合の封入方法、およびそれを備えた磁気デバイスの形成方法を提供する。 - 特許庁
  • To provide a lens drive device capable of preventing occurrence of failure such as plastic deformation or rupture of a spring member when receiving a strong impact such as a drop impact even if the arm part of the spring member must be arranged in a narrow area.
    バネ部材のアーム部を狭い領域内に配置せざるを得ない場合でも、落下衝撃などの強い衝撃を受けた際のバネ部材の塑性変形や破断などといった不具合の発生を防止することが可能なレンズ駆動装置を提供すること。 - 特許庁
  • In the contrary case, supplying the refrigerant to any or all refrigerators is decreased accordingly, and thereupon the influence of the drop of the cooling ability is minimized on the basis of the current cooling action.
    同様に、全体の冷媒需要が全体の冷媒供給を超える場合、極低温冷凍機のいくつかまたはすべてに対する冷媒供給はそれに応じて減少され、それにより、冷却能力低下の影響が現在の冷却作用を基にして最小化される。 - 特許庁
  • When a voice object is pasted to a voice are a 49 by a drag-and- drop operation (steps S701 and S702), display of the voice area 49 on a layout mount sheet 45 in a layout display part 51 is changed from '8) seconds' into '8 to 6 seconds' (step S703).
    音声オブジェクトをドラッグアンドドロップ操作により音声領域49に貼り付けられたとき(ステップS701,S702)、レイアウト表示部51におけるレイアウト台紙45上の音声領域49の表示を、「8秒」から「8/6秒」へと変更する(ステップS703)。 - 特許庁
  • The spacings between screw vanes 68A on the lower side of a feed port 52A and the rice washing cylinder 52 are so sized as not to drop the raw material milled rice and therefore the falling of the raw material milled rice from the opening at the bottom end of the rice washing cylinder 52 in ordinary operation may be prevented.
    また、供給口52Aの下方側のスクリュー羽根68Aと洗米筒52との隙間が原料白米が落下しない大きさであるため、通常運転時に洗米筒52の下端開口から原料白米が落下することを防止できる。 - 特許庁
  • In the case of fire, if the inner layer plug outer shell 5 is incombustible, all the anchor member is not burnt down but remains and, if the inner layer plug outer shell 5 is flammable, only the inner layer plug outer shell 5 is burnt down but its burnt damage is light and anchor slip off and drop out accident can be avoided.
    火災時、 内層プラグ外皮殻5が不燃性の場合はすべてのアンカー部材が焼失せず残存し、可燃性の場合は内層プラグ外皮殻5のみ焼失するが、焼失ダメージは軽微で、アンカー抜け落ち・脱落事故は回避することができる。 - 特許庁
  • Two or more nozzles of a nozzle array at the tip in the scanning direction of an inkjet head are provided with a sensor for detecting light entering from the nozzles, and according to the light detection result of the sensor, the liquid drop discharge drive from each nozzle is controlled to achieve the above object.
    インクジェットヘッドの走査方向の先端のノズル列の2以上のノズルに、ノズルから入ってくる光を検出するセンサを設け、このセンサによる光検出結果に応じて、各ノズルからの液滴吐出駆動を制御することにより、前記目的を達成する。 - 特許庁
  • Only the cyclone separator 16 and the discharge damper device 18 are disposed in a powder transporting route from the hopper 14 to the transportation destination vessel 15, and the filtering device 20 that may cause fluff drop of filter material or peeling of coating material is disposed outside the powder transporting route.
    ホッパー(14)から輸送先容器(15)に至る粉体輸送経路にはサイクロン分離器(16)と排出ダンパー装置(18)のみが配置してあり、濾材のケバ落ちやコーティング材の剥離を生じるおそれのある濾過装置(20)はこの粉体輸送経路の外に配置してある。 - 特許庁
  • To provide an out-of-liquid control method which prevents a liquid drop depending on characteristics of different liquids by controlling an open and close valve and a suck back valve individually without performing complicated valve control, and avoids the out-of-liquid condition for maintaining the optimum state before discharging in the next step.
    バルブの複雑な制御を行うことなく、開閉バルブとサックバックバルブを別々に制御して異なる液体の特性に応じて液だれを防止すると共に、次工程の吐出前の最適状態を維持する液切れの安定化を図れるようにすること。 - 特許庁
  • To provide a hot water storage tank used for a heat pump hot-water heating device, which controls the temperature drop of hot water sent to a heating terminal so as not to ruin the amenity even when the hot water in the hot water storage tank is used for the heat exchange of the hot water to be used for a hot-water supply.
    貯湯タンク内の温水を給湯に使用する温水の熱交換に使用しても、暖房端末へ送る温水の温度低下を抑制し、快適性を損なうことのないヒートポンプ式温水暖房装置に用いる貯湯タンクを提供すること。 - 特許庁
  • Drain water 30 generated in the evaporator 20 is made to drop down from an opening 17a of a partition wall 17 to a drain pan 32, is heated by a compressor discharge pipe 26 to which a refrigerant is pressure fed from a compressor 22, and is evaporated by outside air A3 from a second fan 15.
    蒸発器20で発生するドレン水30は、区画壁17の開口17aからドレンパン32に滴下し、圧縮機22から冷媒が圧送される圧縮機吐出管26によって加熱され、第2のファン15からの外気A3によって蒸発する。 - 特許庁
  • To provide a method for smelting clean steel, which can stably produce the clean steel containing 13 ppm or less total oxygen, without causing a trouble due to the extension of a time period of vacuum degassing treatment or drop in temperature of the molten steel, when smelting the clean steel containing 13 ppm or less total oxygen.
    全酸素濃度13ppm以下の清浄鋼の溶製にあたり、真空脱ガス処理時間の延長あるいは温度低下によるトラブルなく、安定して13ppm以下の清浄鋼の製造が可能とする、清浄鋼の溶製方法を提供する。 - 特許庁
  • To reduce the load on a system operator or on a power user to facilitate the judgment related to lightning damage by calculating the instantaneous drop probability of voltage in a transmission line facility of power system or an electronic factory as electricity receiver and delivering the information therefor.
    電力系統の送電線設備や受電先としての電子工場などにおける電圧の瞬時低下確率を計算してその情報を配信することにより、系統運用者や電力ユーザの負担を軽減し、雷害に関する判断を容易にさせる。 - 特許庁
  • Changes paid out from the coin holding devices for the respective denominations are collected in one drop port by a common duct, dropped onto an inclined distribution plate, and sent out to a left or right predetermined coin paying port by the advance of a paying belt.
    つり銭は、金種別の硬貨保留装置から払い出されたつり銭は共通ダクトによって1つの落下口に集められた後、傾斜する振分板上に落下し、出金ベルトの進行によって左又は右の所定の硬貨出金口に送り出される。 - 特許庁
  • To provide an optical connector adaptor capable of performing the conducting confirmation or contrast inspection of optical fibers nondestructively in a live-line state by connecting the optical connector at the top end of an optical fiber even when an optical fiber with difficulty of confirming leaked light, for example, an optical drop cable is used.
    漏れ光の確認が難しい光ファイバ、例えば光ドロップケーブルを使用する場合であっても、この光ファイバの先端の光コネクタを接続することで、非破壊で、活線状態のまま、導通確認や対照検査を実現できる光コネクタアダプタの提供。 - 特許庁
  • A column lower cover is provided on the bed 2 in the storing gap part, whereby even if chips or mist of a coolant enters the storing gap part, those drop on the lower cover, so that deformation of the bed 2 due to chips having elevated temperature can be prevented.
    また、収納間隙部内のベッド2上にはコラム下カバーが設けられているので、収納間隙部内に切り屑やクーラントの飛沫が侵入しても、それらは、コラム下カバー上に落下するので、高温となった切り屑等によるベッド2の変形を防止できる。 - 特許庁
<前へ 1 2 .... 123 124 125 126 127 128 129 130 131 .... 145 146 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.
  • 金融庁
    Copyright(C) 2026 金融庁 All Rights Reserved.