Quantity of magnetic flux flowing into the coil antenna is increased by using the core of which the cross sectional areas of both end parts are larger than a cross sectional area of a part onto which the conductive wire is wound. 両端部の断面積が、導線が巻回されている部分の断面積より大きいコアを使用することによって、コイルアンテナへ流入する磁束の量を増やす。 - 特許庁
A plating method using a plating solution containing no brightener, or a method wherein surface is roughened by etching is performed in order to form the roughened surface of the copper bump 3. 銅バンプ3の粗面3aを形成するには、光沢剤を含まないメッキ液を用いてメッキを行なう方法、または表面をエッチングにより粗面化する方法が採られる。 - 特許庁
A second phase difference is calculated by using the same technique but a time offset is the delay expressing a relative delay of two optical transmissions in the test interferometer. 第2の位相差は、同じ技法を使用して計算されるが、時間オフセットは、試験干渉計内の2つの光伝達の相対的な遅延を表す遅延である。 - 特許庁
In addition, as a condition for reel packing of the tape-shaped semiconductor device by using the spacer tape 10, the spacer tape 10 is laminated on the tape carrier 4 and is wound on a reel. また、テープ状の半導体装置をスペーサテープ10を用いてリールに梱包する状態としては、テープキャリア4にスペーサテープ10を重ね合わせリールに巻きつける。 - 特許庁
Or, instead of fixing the side of the imaging device attaching board 4 to which the imaging device 2 is attached, the wide angle lens is made movable by using a similar mechanism. あるいは、撮像素子2を取り付けた撮像素子取付基板4側を固定する代わりに、広角レンズを前述と同様の機構を用いて移動可能とする。 - 特許庁
To provide an optical fiber which is a compact nonlinear device with high efficiency by using a tellurite fiber whose zero-dispersion wavelength is shifted to a 1.4 to 1.7 μm band as a communication wavelength band. 零分散波長を通信波長帯である1.4〜1.7μm帯にシフトしたテルライトファイバを用いて、コンパクトで高効率な非線形デバイスである光ファイバを提供する。 - 特許庁
In displaying the subject distance, the moving direction of the focusing lens is detected and the subject distance is calculated from the position of the focusing lens by using the characteristic data of this direction. そして、被写体距離を表示する際に、フォーカスレンズの移動方向を検出して、その方向の特性データを使用してフォーカスレンズ位置から被写体距離を算出する。 - 特許庁
Heat is applied from a heater 4 to the bean A thrown down from a chute 3 and a temperature distribution of the bean A just after heating is studied using an image of an infrared monitoring camera 5. シュータ3から投下される豆Aに加熱器4から熱を加え、加熱直後の豆Aの温度分布を赤外線監視カメラ5の画像を用いて調べる。 - 特許庁
The circuit is analyzed using static analysis or DC analysis and an initial local effect for the circuit device including body effect and local heat effect is obtained. 回路は静的解析または直流解析を使用して解析されて、ボディ効果および局部的熱効果を含んだ、回路デバイスに対する初期局部効果が得られる。 - 特許庁
To provide a photoreactive crosslinking agent that is capable of crosslinking a sequence which cannot be photo-crosslinked by psoralen, and is capable of photo-crosslinking using a light having a longer wavelength, as compared with psoralen. ソラレンでは光架橋できない配列に対して架橋可能であって、ソラレンより長波長の光を用いて光架橋可能な光反応性架橋剤の提供。 - 特許庁
By using the signal cables 6, there is no need for providing initial distortion for optical fibers at the time of underlaying cables, and it is possible to perform efficient underlaying work. 上記信号ケーブル6を使用することにより、ケーブルの敷設時に光ファイバに初期歪みを与える必要がなく、敷設作業を効率的に行なうことが可能となる。 - 特許庁
Since such direct joining method is adopted, the size of the solid electrolytic capacitor itself is reduced as compared with the solid electrolytic capacitor manufactured by using the conventional wire bonding method. このような直接接合法を採用することで、従来のワイヤボンディング法を使用した固体電解コンデンサに比較して、コンデンサ自体を小型化することができる。 - 特許庁
Moreover, the display portion is formed using a substrate which is a light-transmitting substrate such as a glass substrate provided with a single crystal semiconductor layer separated from a single crystal semiconductor substrate. また、表示部は、ガラス基板等の透光性の基板に、単結晶半導体基板から分割された単結晶半導体層を設けた基板で作製される。 - 特許庁
In forming the image, the LUT corresponding to the recording mode is acquired and the exposure corresponding to an input image signal is corrected by using the LUT. そして、画像形成を行う際に、記録モードに対応するLUTを取得し、当該LUTを用いて入力画像信号に対応する露光量を補正する。 - 特許庁
Feedback information is derived from a response of at least one receiver to a transmission signal, and is fed back using multiplexed feedback signals. フィードバック情報は、送信信号に対する少なくとも1つの受信器の応答から導出され、そしてマルチプレクスされたフィードバック信号を用いてフィードバックされる。 - 特許庁
The ceramic heater 1 heats a heating object using a ceramic body 10 which is formed of ceramics and a terminal 20 to which electric current from a power supply is supplied. 本発明のセラミックヒータ1は、セラミックスにより形成されるセラミック体10と、電源からの電流が供給される端子20とを用いて、加熱対象物を加熱する。 - 特許庁
An RFID antenna (18) is printed on a substrate using conductive ink, and the substrate is incorporated in a decorative side (16) like a high-pressure decorative laminate as a layer. 基板上にRFIDアンテナ(18)を導電性インクを用いて印刷し、その基板を高圧装飾ラミネートのような装飾面(16)の中の一層として組み込む。 - 特許庁
By repeatedly using the common memory area of the RAM 6 in the range- finding performed twice, the range-finding in a wide range is performed even by the microcomputer whose memory capacity is small. このように2回の測距において、RAM6の共通のメモリ領域を繰り返して使用することでメモリ容量の少ないマイコンでも広範囲の測距が行える。 - 特許庁
When a possibility of a logical error concerning some region is detected, at least a part of navigation processing is executed using data on the other regions as backup processing. いずれかの領域について論理エラーの可能性が検出されたときに、他の領域のデータを用いてナビゲーション処理の少なくとも一部をバックアップ処理として実行する。 - 特許庁
To provide an underwater visible light communication system in which a wavelength of visible light is varied in accordance with the situation of water quality and further the time of driving using a battery is prolonged. 水質の状況に応じて可視光の波長を変えることができて、しかもバッテリによる駆動時間を延ばすことができる水中可視光通信システムを提供する。 - 特許庁
The SSW selects a set in which defect is least (does not exist) and new servo track is written in the magnetic disk by servo control using the servo sector of the set. SSWは、欠陥が最も少ない(存在しない)セットを選択し、そのセットのサーボ・セクタを使用したサーボ制御により新たなサーボ・トラックを磁気ディスクに書き込む。 - 特許庁
To provide an excellent one-pack aqueous waterproof material composition for the civil engineering which is prepared by using an aqueous polyurethane having no volatilization of an organic solvent during operation and is excellent in workability. 作業中に有機溶剤の揮散のない水性ポリウレタンを用い、施工性に優れた土木建築用の優れた一液型水性防水材組成物を提供する。 - 特許庁
To obtain a window regulator, in which the degree of freedom of arrangement can be improved and durability is enhanced and the generation of an abnormal sound is prevented in a constitution using a tape. テープを用いた構成において、レギュレータの配置の自由度を高めることができ、しかも耐久性の向上及び異音発生の防止を図れるウインドレギュレータを得る。 - 特許庁
Thus, a heat-resistant characteristic is improved by using polyolefin wax as the flux film instead of conventional paraffin wax, and its operability is also improved at the time of manufacturing. ここで、フラックス被膜に従来のパラフィンワックスに替えてポリオレフィン系ワックスを使用することで、耐熱特性が改善され、製造時の作業性が向上できる。 - 特許庁
After the surface of the substrate for the mask blank is polished in a polishing step of polishing a substrate using a polishing liquid containing polishing grains, the surface is acted upon by high concentration ozone gas. 研磨砥粒を含む研磨液を用いて研磨する研磨工程によりマスクブランク用基板表面を研磨した後、該基板表面に高濃度のオゾンガスを作用させる。 - 特許庁
A rotating speed of the pumps 12, 14 is controlled by using an inverter 24 in the operation of the melting furnace 1, and the degree of vacuum in the furnace body 6 is adjusted by varying the suction force. 溶解炉1の操業においてインバータ24を用いてポンプ12,14の回転速度を制御し、その吸引力を可変して炉体6内の真空度を調整する。 - 特許庁
The air conditioner 100 has high energy efficiency and high heating capability because of the heating operation, using radiation heating in which an evaporator is 111 is heated by irradiation with near-infrared rays. エアコン100は、近赤外線を照射し蒸発器111を加熱する輻射加熱を利用した暖房運転を行うため、エネルギー効率が高く、暖房能力が高い。 - 特許庁
Communication on the bus is allowed to the hand-held communication controller by using a communication schedule, and the search algorithm is used to detect devices including other communication controller. ハンドヘルド通信制御装置は、通信スケジュールを用いてバス上での通信が許可され、他の通信制御装置を含む装置を検出するために探査アルゴリズムを用いる。 - 特許庁
The output power of a thin film solar cell module using a no cure sealing material is increased by conducting heat treatment of a thin film solar cell after a rear surface electrode is formed. 裏面電極形成後に薄膜太陽電池の熱処理を行うことで、ノーキュア封止材を用いた薄膜太陽電池モジュールの出力電力を増加させる。 - 特許庁
In particular, the diode is constituted using the (111) boron-phosphide-based semiconductor layer 106 which is excellent in matching with the (0001) surface of the Group III nitride semiconductor thin-film layer 105. 特に、III族窒化物半導体薄膜層105の(0001)面とのマッチングに優れる(111)リン化硼素系半導体層106を利用して構成する。 - 特許庁
A resist pattern 4 is formed and subjected to anisotropic dry etching using the pattern as a mask to form a gate electrode 5 on a gate insulating film 2, and then the resist pattern 4 is removed. レジストパターン4を形成し、それをマスクとして異方性ドライエッチングを行うことによりゲート電極5をゲート絶縁膜2上に形成し、レジストパターン4を除去する。 - 特許庁
To obtain a zoom lens by which a photographing viewing angle is widened, and whose portability is excellent by shortening a lens entire length, and which consists of three groups, and to provide an optical equipment using the zoom lens. 撮影画角の広角化を図ると共に、レンズ全長の短縮化を図った携帯性に優れた3群より成るズームレンズ及びそれを用いた光学機器を得ること。 - 特許庁
Accordingly, waste of energy can be prevented by using a coil with a small inductance at the time of a light load, that is in the case the capacity CL of the printing head H is small. このように、軽負荷、即ち、印字ヘッドHの容量CLが小さくなる時には、コイルのインダクタンスも小さいものを用いることで、エネルギーの浪費を防止する。 - 特許庁
An article 101 is suspended at some angle from a dropping unit using at least one string or wire and the suspending material is released substantially immediately before first collision. 物品を少なくとも1本の紐またはワイヤーを用いて落下装置から或る角度で吊り下げ、その吊り下げ材料を最初の衝突の直前に実質的に開放する。 - 特許庁
The condensed water is mixed with raw fuel G without using other service water and sent to the fuel reformer 11, and then, the reformed fuel gas is sent to the fuel electrode 2. その凝縮水を他の市水を用いることなく原燃料Gと混合し、燃料改質器11に送り込み、改質後の燃料ガスを燃料極2へ送り込む。 - 特許庁
Then, after conditioning by a pad conditioner 4 is performed, a semiconductor wafer is placed on the polishing pad 2 and subjected to a CMP treatment by using a polishing head 5. その後、パッドコンディショナ4によってコンディショニングを行った後、研磨パッド2に半導体ウェーハを載置し、研磨ヘッド5によって半導体ウェーハをCMP処理する。 - 特許庁
When performing the restoration using the backup data, the hardware information (a) included in the backup data is extracted, and is compared with the hardware information (a) acquired from the inside of the information processor itself. 一方、バックアップデータを使ったリストアを行う場合、バックアップデータに含まれるハードウェア情報aを抽出し、自装置内から取得されるハードウェア情報aと比較する。 - 特許庁
A fiber immersing and absorbing treatment bath is prepared by using the dispersion composition and a fiber material is treated therewith to obtain the fiber material having functions of the functional agent imparted thereto. この分散組成物を用いて繊維浸漬吸収処理浴を調製し、繊維材料を処理することにより、機能剤の機能が付与された繊維材料が得られる。 - 特許庁
When a parallel test in a semiconductor memory device is performed, write data is held in a dedicated latch circuit by using a command dedicated to the parallel test prior to issuing a WRITE command. 半導体記憶装置のパラレルテスト実施時は、WRITEコマンドの発行に先立ちパラレルテスト専用のコマンドにより書き込みデータを専用のラッチ回路に保持しておく。 - 特許庁
The transmission driving part 5 is controlled by the signal from the control part 7, the ultrasound is transmitted by short-time driving the transceiver 1 or 2 intermittently using the constant voltage. 制御部7からの信号で送信駆動部5を制御し、前記定電圧を用いて送受波器1又は2を間欠的に短時間駆動して超音波を送信する。 - 特許庁
When the merchandise is reserved or purchased, information related to receiving and using the merchandise is transmitted together with classification information to an information receiving terminal 10 from a server 30. 商品の予約や購入時に、サーバ30から情報受信端末10に、この商品の受け取りや利用に関連する情報が分類情報と共に伝送される。 - 特許庁
To provide a thermit welding method for rails by which the fatigue performance of a welded joint part is improved even when using a bisecting type casting mold which is high in execution efficiency. 施工能率の高い2分割式鋳型を用いても、溶接継手部の疲労性能を向上させることができるレールのテルミット溶接方法を提供する。 - 特許庁
The dry etching is applied to the silicon carbide substrate 11 from a rear side using fluorine-based gas (second gas), by which a backside viahole 18 connected to the surface viahole 14 is formed. 弗素系ガス(第2のガス)を用いて裏面側から炭化ケイ素基板11をドライエッチングすることで、表面バイアホール14に繋がる裏面バイアホール18を形成する。 - 特許庁
A first CMP (chemical mechanical polishing) is then performed using slurry containing a Cu protective film forming agent sufficiently such that the polishing rate of Cu is sufficiently higher than the polishing rate of TaN. 次に、Cuの研磨レートがTaNの研磨レートより十分大きく、かつ、Cu保護膜形成剤が十分に含有されたスラリーを用いて第1のCMPを行う。 - 特許庁
An SiCN layer 102 as an etching stopper layer is formed on a lower layer, and the SiCN layer 102 is subjected to plasma etching, using plasma of an etching gas containing CF_4 and NF_3. 下層には、エッチストッパー層としてSiCN層102が形成されており、このSiCN層102を、CF_4と、NF_3とを含むエッチングガスのプラズマを用いてプラズマエッチングする。 - 特許庁
A flapper for air capacity distribution is provided behind an air course of a fan, and its angle is changed in synchronism with both-surface unit conveyance timing by using a solenoid performing both-surface conveyance. ファンの風路の後に風量振り分けのフラッパを設け、その角度変更を両面搬送を行っているソレノイドを用いて、両面ユニット搬送タイミングと同期して行う。 - 特許庁
To provide an acoustic type gas temperature measurement system which is economically capable of responding to large furnaces, has a small measurement error and is capable of responding to cases using variety of fuel. 経済的に大型火炉に対応可能で、計測誤差が小さく、かつ多様な燃料を用いた場合にも対処できる音響式ガス温度計測装置を提供すること。 - 特許庁
After updating firmware in a storage part 22 by using the update program, the electronic apparatus 200 is forcibly restarted and the update program is automatically started. 電子機器200において、記憶部22内のファームウェアの更新を更新プログラムを用いて行った後は、再起動が強制的に行われて、更新プログラムが自動的に起動する。 - 特許庁
An inputted voice signal (304) is efficiently processed (305) by using the environmental information and the processing result is outputted (306). 入力した音声信号(304)について、環境情報を用いることで入力音声信号の処理(305)を効率よく行い、その処理結果を出力する(306)。 - 特許庁
To provide a cartridge filter using a hydrophilic microporous precision filter membrane which is adequately usable for manufacturing processes, etc., of semiconductors, medical supplies, etc., and is excellent in chemical resistance. 半導体や医薬品等の製造過程等に好適に使用し得る、耐薬品性に優れ親水性の微孔性精密ろ過膜を使用したカートリッジフィルターを提供する。 - 特許庁