Offset toner removed from a peripheral face of the pressure roller 22 by the cleaning roller 25 is led to one end of the cleaning roller 25 by the spiral spring coil 27 and discharged from the end of the roller 25. クリーニングローラ25が加圧ローラ22の周面から除去したオフセットトナーは、螺線状のバネコイル27によってクリーニングローラ25の一端部方向に導かれ、トナーをその端部から排出させる。 - 特許庁
To protect a system by automatically meeting the wind direction, and automatically moving blade pitch backward by springpressure without separate pitch control even in super-strong wind so as to prevent an overload on a power generator. 自動的に風向に合わせ、超強風であっても別途のピッチ制御なしにばね圧力によって ブレードが自動的に後方へ可変して発電機の過負荷を防止するなどシステムを保護する。 - 特許庁
A blade tensioner 10 is formed which consists of a blade shoe 11 and a blade spring 12 disposed on the side opposite from the chain sliding surface 11a of the blade shoe for exerting pressure on a timing chain 4 via the blade shoe 11. ブレードシュー11と、そのチェーン摺動面11aと逆側に配設され、ブレードシュー11を介してタイミングチェーン4に押付力を作用させるブレードスプリング12とからブレードテンショナ10を構成する。 - 特許庁
When an inlet 6 of a casing 2 applies fluid pressure to a valve element 3, a check valve 1 allows the fluid to flow by separating the valve element 3 from a valve seat 8 in opposition to energization force of a spring 4. 逆止弁1は、ケーシング2の入口6から弁体3に流体圧力が作用したとき、スプリング4の付勢力に抗して弁体3を弁座8から引き離して流体の流通を許容する。 - 特許庁
The diaphragm spring 5 has a thrust portion 5a for thrusting the pressure plate 4 and a lever portion 5b for amplifying the operating force of a release mechanism at a preset lever ratio to cancel the thrusting force of the thrust portion 5a. ダイヤフラムスプリング5は、プレッシャプレート4を押圧する押圧部5aと、レリーズ機構の作動力を所定のレバー比で増幅して押圧部5aによる押圧力を解除するためのレバー部5bとを有する。 - 特許庁
When using the device on the surface to be worked, the finger rows on the preceding and rear sides are moved under a springpressure for making finger tips engage with the surface to be worked, and the water is excluded from the inside of the housing. 加工面に装置を使用すると、先行側および後側のフィンガー列は、その末端を加工面に対して係合させるためのばね圧の下で移動し、ハウジング内から水を排除する。 - 特許庁
When a steering wheel 5 is not operated, the spring 11 is kept in a nearly free length to minimize the pressure loss with respect to a flow led to a working-machine system flow passage 19. そして、ステアリングホイール5を操作していないときには、上記スプリング11をほぼ自由長に保って、作業機系流路19に導かれる流れに対して、その圧力損失を最少にする。 - 特許庁
Thereby, an urging force in a direction (R1 direction) approaching the wiping surface 30 relative to the retainer 22 of the spring 72, or the contact pressure of a wiper blade to the wiping surface 30 can be stabilized. これにより、スプリング72のリテーナ22に対する払拭面30に接近する方向(R1方向)への付勢力、ひいては、ワイパブレード28の払拭面30への接触圧を安定させることができる。 - 特許庁
The projected parts 10-1 contact the upper part of the solid lubricant 8 and the solid lubricant 8 serves as resistance to welding pressure F to be welded to a lubricant application roller by a spring 9. この凸部10−1は固形潤滑剤8の上部に接しており、固形潤滑剤8がばね9により潤滑剤塗布ローラに加圧される加圧力Fに対する抵抗力となっている。 - 特許庁
Between the housing 10 and inner rotor 20, a multiple-disk friction mechanism 30 consisting of disks locked in directions of rotation, a pressurespring 40, and a rotary cam mechanism 50 are arranged in coaxial relation. ハウジング10と内側回転体20の間に、それぞれに回転方向に係止された円盤体からなる多板摩擦機構30と、押しばね40、回転カム機構50を同軸上に配する。 - 特許庁
A movable valve 30 between an open position and a shutdown position, a bucket tappet 40 which has the lifter plate 41, an actuator 70 in the hydraulic pressure as a swing means, spring 72, and solenoids 80 are installed. 開放位置および閉塞位置間で移動可能なバルブ30と、リフタプレート41を有するバケットタペット40と、揺動手段としての液圧アクチュエータ70、スプリング72およびソレノイド80とを設ける。 - 特許庁
The oscillatory arm 4 is pulled by a spring 6 to be oscillated and the pressure roller 5 is pressed to the rubber sheet 2 and pulled by the plunger 9a of a solenoid 9 to release the pressing of the rubber sheet 2. 揺動アーム4はバネ6により引かれて揺動し押圧ローラ5がゴムシート2に押圧され、電磁ソレノイド9のプランジャ9aに引かれて押圧が解除されるように構成したことを特徴とする。 - 特許庁
When upward and downward acceleration acting on a vehicle is large, preliminary hydraulic pressure is applied to a wheel cylinder of a drum brake, a brake shoe is actuated in an enlarging direction against an energization force of a shoe return spring. 車両に作用する上下方向加速度が大きいときに、ドラムブレーキのホイールシリンダに予備的な液圧がかけられ、ブレーキシューがシューリターンスプリングの付勢力に抗して拡開方向に動作させられる。 - 特許庁
To reduce waste of energy obliged to perform against pressure of a simulation spring, for contacting a control rod with a piston of a master cylinder, when a vacuum supply device causes failure. 真空供給源が故障した場合に、制御ロッドをマスターシリンダーのピストンと接触させるためにシミュレーションスプリングの圧力に抗して行わなければならないというエネルギーの浪費を少なくする。 - 特許庁
The actuator 10 is driven by air from an air spring 12, where pressure varies in proportion to the load on the axle 28, and rotates the arm portions 2, 2 at the arbitrary rotating position by using this air. アクチュエータ10は、車軸28に掛かる荷重に比例して圧力が変化するエアスプリング12からのエアーによって駆動し、このエアーを利用してアーム部2,2を任意の回転位置に回転させる。 - 特許庁
A clutch disk 23 is pushed toward a flywheel 21 by a spring 25 through a pressure plate 24, and an actuator 30 generates the force for resisting the described pushing force in response to the operating condition of a vehicle. クラッチディスク23はプレッシャプレート24を介してスプリング25によりフライホイール21側に押圧され、アクチュエータ30は車両の運転状態に応じて上記押圧力に抗する力を発生する。 - 特許庁
A deflector body 20 projecting from the upper surface of a roof 12 is changed in height by the urging force of a coil spring 36 and wind pressure applied to the wind-catching part 28 of the deflector body 20. コイルスプリング36の付勢力とデフレクタ本体20の風受部28が受ける風圧との関係で、ルーフ12の上面からのデフレクタ本体20の突出高さが変化するようになっている。 - 特許庁
The fitting length of the pressure pads 20 in the cylindrical parts 1a and 1b can be made larger than their outside diameters irrespective of the set load of a coil spring 7, which ensures a smooth sliding operation. プレッシャ・パッド20は、コイルスプリング7のセット荷重に拘わらず、筒状部1a,1b内での嵌合長さの方がその外径より長くすることができ、これにより、スムーズにスライドすることができる。 - 特許庁
Since the push rod provides two different intensification ratios as a reference function of value of input, it stores the pressure reduction piston (62) resiliently restored by a spring (66) made of plastic material. プッシュロッドは、入力の値の関数として二つの異なる補力比を提供するため、プラスチック材料製のばね(66)によって弾性的に復元される減圧ピストン(62)を収容している。 - 特許庁
This piston 5 is accepted reciprocatingly against the prestress force of a compression spring 7 in a pump cylinder 4 and driven by a cam 8 and carries the fuel loaded by a high pressure in a rail. このポンプピストンはポンプシリンダ(4)内で圧縮ばね(7)のプレストレス力に抗して往復に可動に受容されていて、カム(8)によって駆動され、高圧で負荷された燃料をレール内に搬送する。 - 特許庁
A piston 10 is arranged between a front cover of a torque converter and a turbine axially thereof, axially movable due to a change in a hydraulic pressure, and coupled to a driven plate 7 through a torsion spring 4. ピストン10は、トルクコンバータのフロンとカバーとタービンとの軸方向間に配置され、油圧の変化によって軸方向に移動可能であり、トーションスプリング4を介してドリブンプレート7に連結可能である。 - 特許庁
A spring 14 on the lower side of the piston 5 moves the piston 5 upward and locks the same, and pressure oil in a release chamber 12 formed on the upper side of the piston 5 moves the piston 5 downward and releases the same. そのピストン5の下側のバネ14が上記ピストン5を上方へロック移動させ、上記ピストン5の上側に形成したリリース室12の圧油が上記ピストン5を下方へリリース移動させる。 - 特許庁
This clutch control device comprises an actuator 30 axially displacing a clutch disc 23 opposed to a flywheel 21 rotating integrally with the crankshaft 10a of an engine through the pressure plate 24 and the diaphragm spring 25. エンジンのクランクシャフト10aと一体的に回転するフライホイール21に対向するクラッチディスク23をプレッシャプレート24及びダイヤフラムスプリング25を介して軸方向に変位させるアクチュエータ30を備えている。 - 特許庁
A forcibly opening spring 46 is provided between a lower patch plate 44 butted to the diaphragm 35 and a pressure sensitive rod for transmitting displacement of the diaphragm 35 to a valve element 18 in a lower case 34. 下部ケース34内において、ダイアフラム35に当接される下部当金44と、ダイアフラム35の変位を弁体18に伝達するための感圧ロッド21との間に、強制開放スプリング46が設けられる。 - 特許庁
Since a movable mold 3 is pressed to a fixed mold 2 through the pressure of the cushioning oil 5 during mold clamping, mold clamping force can be adjusted by adjusting the size of the restoration force of the adjustment spring 9. 型締め時には前記緩衝油5の圧力を介して可動型3が固定型2に押圧されるから、前記調整バネ9の復元力の大きさを調整することで型締め力を調整できる。 - 特許庁
On clamping, the pressure-receiving surfaces 14a and 22a of the rotary plate and the fixing base come into mutual contact against the elastic force of the disc spring 30, transmitting the clamping load P reliably to the fixed base 22. 一方、型締め時には、皿ばね30の弾性力に抗して回転板及び固定ベースの受圧面14a、22a同士が当接し、型締め荷重Pを固定ベース22に確実に伝達する。 - 特許庁
By changing the spring constants of these springs, or by changing push- down amounts of respective pins, the contact pressure between the power-supply pin 91 and the contact unit is made larger than that between the signal pin 101 and the contact unit. これらバネのバネ定数を変えたり、あるいは各ピンの押下量を変えて、電源ピン91と接触子との接触圧力を、信号ピン101と接触子との接触圧力より大きくする。 - 特許庁
A spring part 21 of a contact 20 is bent, the conductive pattern of a FPC 30 makes pressure-contact with the projecting contact part 25, and thereafter, the reinforcing plate 40 is fixed to a base insulator 10 by a lock member 50. コンタクト20のばね部21を撓ませ、FPC30の導電パターンを突起状接点部25に圧接した後、ロック部材50によって補強プレート40をベースインシュレータ10に固定する。 - 特許庁
The discharge port is opened by the backward movement of the plunger rod by an air pressure and the liquid drops are discharged from the discharge port by an advance movement of the plunger rod with the elastic force of a spring. エアー圧力によるプランジャーロッドの退行動作により吐出口を開き、スプリングの弾性力による前記プランジャーロッドの進出動作により液滴を前記吐出口より吐出する。 - 特許庁
In a non-energization state to the electromagnetic plunger 91, the valve member 82 is opened when receiving the action of a tensile spring 93, whereby the pressure state by the air- pressurizing pump is forcibly released. また、電磁プランジャー91への非通電状態においては、引っ張りばね93の作用を受けて弁部材82は開弁され、空気加圧ポンプによる加圧状態が強制的に解除される。 - 特許庁
An operation part 15 operating the part molding core 9 so as to protrude the same by the sliding of the slide shaft 12 is provided at the slide shaft 12 slid through the spring 14 when the pressure plate 13 is pushed. 押圧板13が押されたときばね14を介して摺動する摺動軸12に摺動軸12の摺動により上記部分成形コア9が突出するように作動させる作動部15を設ける。 - 特許庁
A leg part 38 of a spring friction body is elastically pressure welded on a peripheral wall 40A on the inside of a ring recessed part 40 of a rack guide 24 in a state before a cap 26 is perfectly scrwed. キャップ26が完全に螺合される前の状態において、ばね・摩擦体34の脚部38は、ラックガイド24の環状凹部40の内側の周壁40Aに弾性的に圧接されている。 - 特許庁
A boss for stopping the rotation of a cartridge, a developing pressurespring and a force receiving part for receiving separating force from a main body are arranged on the same radius from the center of turning where a developing unit is turnably supported in a cleaning unit. クリーニングユニットに現像ユニットを回動可能に支持する回動中心から同一半径上にカートリッジの回り止めボス、現像加圧バネ、本体より離間の力を受ける力受け部を配置する。 - 特許庁
A spring area 24 curved with pressure by the side projection 19 of the insertion body 15 when the insertion body 15 is inserted into the insertion space 22a is formed on the holding side face 22 of the handle portion 20. 把持部20の保持側面22に、挿入空間22aに挿入体15が挿入される際、挿入体15の側面突起19により押圧されて湾曲するバネ領域24が形成されている。 - 特許庁
When hydraulic pressure is not applied to the oil chamber 18, a second plunger 28 has a first attitude A pressed against the first plunger 12 by energizing force of a spring 29 on the operating body 20 side. 油室18に油圧が加わらないときには、第2のプランジャ28は、作動体20側のスプリング29の付勢力により第1のプランジャ12に押し付けられた第1の姿勢Aとされる。 - 特許庁
Even though the edge bites into by the brush roller 505 because the shape of the lubricant 506 is changed, the pressure is weakened, because the length of a compression spring 523 is elongated, so that the bristle tilting of the brush roller 505 will not occur. 潤滑剤506の形状が変化してエッジがブラシローラ505に食い込むことも有り得るが、圧縮スプリング523の長さが伸びて圧力が弱まるため、ブラシローラ505に毛倒れは生じない。 - 特許庁
When the coil 10 does not carry a current, the movable body 9 is energized upward by a spring 16, and a back pressure chamber 14 is closed due to the contact of the closing member 19 and a packing 22. コイル10への通電がなされていないときには、可動体9がスプリング16によって上方に付勢されており、閉止部材19とパッキン22との当接によって、背圧室14が閉止されている。 - 特許庁
Furthermore, the tension roller 41 is provided with a tension-mitigating mechanism 50 which moves the tension roller 41 by a prescribed distance, in the direction in which the tension decreases, from the position at which the pressure is added by the tension spring 46R, when an image is not formed. さらに、画像非形成時には、テンションスプリング46Rにより加圧されている位置から張力が減ずる方向にテンションローラ41を所定の距離だけ移動させる張力緩和機構50を有する。 - 特許庁
When the exhaust valve actuator is in the open position, and the hydraulic chamber for opening is connected to the high pressure hydraulic fluid source, closing force of the double-acting spring is balanced with opening force of the hydraulic chamber for opening. 排気弁アクチュエータがその開放位置にあり、開放用油圧チャンバを高圧油圧流体源に連結する場合、複動ばねの閉鎖力は開放用油圧チャンバの開放力と釣り合う。 - 特許庁
In the case that the working depth of the plowing body 6 is deeper than the set depth, since the liking body 25 leaves from the contacting part 15, the gas spring 31 becomes a state of not energizing the leveling body 7 in the direction of reducing earth-contacting pressure. 耕耘体6の作業深さが設定深さより深い場合、リンク体25がリンク当接部15から離れるため、ガススプリング31が整地体7を接地圧減少方向に付勢しない状態となる。 - 特許庁
A printer 1 has a medium storage part 3 composed of a medium tray 4 and a loading plate 6, and the recording medium P loaded on the loading plate 6 is brought into pressure contact with a paper feed roller 8 by a pressing spring 7. プリンタ1には媒体トレイ4と積載板6から成る媒体収納部3を有し、積載板6に積載される記録媒体Pは押圧スプリング7により給紙ローラ8に圧接される。 - 特許庁
The main body 14A is energized to the side of a cylinder hole 2b by a first spring 21, and the main body 14A is made to hit on a bottom surface of the sliding hole 2g until working oil in the cylinder hole 2b reaches specified initial pressure. 本体14Aを第1のばね21によってシリンダ孔2b側へ付勢し、シリンダ孔2b内の作動油が所定の初期圧に達するまで本体14Aを摺動孔2gの底面に突き当てる。 - 特許庁
On the contrary, when pressure air is introduced from an air introduction passage 32 formed in the side face of a cylinder 16, the piston rod 28 is displaced while overcoming the force of the spring 30 and the valve 26 is thus opened. これに対し、シリンダ16の側面に形成されているエア導入路32から加圧エアが導入されると、ピストンロッド28がスプリング30の力に打ち勝って変位し、ひいては、バルブ26が開弁する。 - 特許庁
Therefore, pressure oil in holding conduits 11, 12 is led to spring side pilot chambers 17a, 18a of spools 17, 18 of counter balance valves 5, 6, and then the spools 17, 18 are closed to stop the rotation of the hydraulic motors 2, 3. これにより、保持管路11,12の圧油がカウンタバランス弁5,6のスプール17,18のバネ側パイロット室17a,18aに導かれ、スプール17,18が閉ざされて油圧モータ2,3の回転が停止される。 - 特許庁
An oil supply pipe 20 is moved to a communication blocking position by biasing force of a return spring 46 during the generation of negative pressure and blocks communication between the oil path 20a and the atmospheric space through the atmosphere communication hole 20b. 給油パイプ20は、負圧発生中にはリターンスプリング46の付勢力によって連通阻止位置に移動し、大気連通孔20bを通じた油路20aと大気空間との連通を阻止する。 - 特許庁
The connecting terminal 30 clamps the tongue 24 between the connecting terminal and the side face of the terminal housing hole 12 under specified springpressure, and is further provided with an elastic connecting piece 33 connected with the wiring lead-out portion 23. 接続端子30は、端子収容孔12の側面との間で舌片24を所定のバネ圧をもって挟み込むと共に配線引出部23と接続される弾性接続片33を有する。 - 特許庁
After the injection, with the lowering of the resin pressure acting on the tip part 8a, the insert 8A advances by the energizing force of the spring 11, and the protrusion 8c of the tip part 8a advances into the cavity 3. 射出後は先端部8aに作用する樹脂圧の低下に伴いばね11の付勢力で可動式入子8Aが前進し、先端部8aの突部8cがキャビティ3内に進出する。 - 特許庁
To enable a push-in operation force and a contact pressure of an operation body to be individually decided despite a single leaf spring material mounted on the operation body has two of a first and a second contact piece parts. 操作体に取り付けた単一の板ばね材が第1及び第2の2つの接片部を有しているにもかかわらず、操作体の押込操作力と接点圧とを個別に定めることができるようにする。 - 特許庁
Turning motion of an inner support cam 54 by the pedal shaft 3 turned urges an outer support cam 52 away to impose a heavier load on the multiple-disk friction mechanism 30 via the pressurespring 40, which results in larger frictional force. ペダル軸3の回動により内側支持カム54が回動し、外側支持カム52を押し離し、押しばね40を介して多板摩擦機構30への荷重を大きくするため摩擦力が大きくなる。 - 特許庁
For the biasing means, coned disk springs 28 of which the shape is changed flexibly within a nonlinear spring region wherein the variation of resilience in relation to the amount of flexible deformation is small when a set force of pressure contact is given are sued. また、付勢手段は、設定圧接力が加えられて撓み変形量に対する弾発力の変動が小さい非線形ばね領域内でたわみ変形される皿ばね28とした。 - 特許庁