A casing 422 for a ball bearing 420 holding the ball screw 412 can be displaced on a supporting stand 418 by resisting the energizing force of a compression coil spring 444 and a tensile coil spring 450 and tends to be vibrated on the supporting stand 418 by transmitting the vibration of the ball screw 412 to the casing 422. ボールねじ412を保持するボールベアリング420のケーシング422は、圧縮コイルスプリング444及び引張コイルスプリング450の付勢力に抗すれば支持台418上で変位でき、ボールねじ412の振動がケーシング422に伝達されれば、支持台418上で振動しようとする。 - 特許庁
An improvement body 7 reaching a gravel layer 21 is provided in both lateral directions of a designed tunnel position 3 so as to be taken as an impervious wall against spring water from the natural ground, an upper part of prelining 11 is provided with a drainage tube 17, and the spring water from the gravel layer 21 is collected for drainage in order to lower the groundwater level. 計画トンネル位置3の両側方に、れき層21に到達する改良体7を設け、地山からの湧水に対する遮水壁とし、先受け工11の上部に水抜きチューブ17を設け、れき層21からの湧水を集水して排水し、地下水位を低下させる。 - 特許庁
The placing member 18 and the horizontally sliding member 16 provide base isolation action by achieving a long period of vibration property (wave shape) for travel (vibration) in the vertical or horizontal direction by viscous resistance action and spring elastic action by dash pots 38, 40 (or 32, 34) and a spring member 28 (or 22). そして、載置部材18と水平滑動部材16は、ダッシュポット38、40(又は32、34)及びばね部材28(又は22)により、垂直又は水平方向の移動(振動)を粘性抵抗作用とばね弾性作用で、振動性状(波形)を長周期化させて免震作用を奏する。 - 特許庁
In addition, conduction between an outside conductor 58 of the first connection member and an outside conductor 72 of the second connection member is implemented by a conductive ring receiver 68, a conductive spring receiver 94, and two conductive rings 96 and 98 provided between the conductive ring receiver and the conductive spring receiver. また、第1の接続部材の外部導体58と、第2の接続部材の外部導体72との導通は、導電性リング受け68と、導電性スプリング受け94と、導電性リング受けと導電性スプリング受けとの間に設けられた2個の導電性リング96,98とにより実現される。 - 特許庁
According to this constitution, since the elastic force of the outer spring closing the main poppet will be canceled by the inner spring, even if external force acts on and cylinder flow-out quantity increases, while being contracted, the pressure of the tank side will not increase, and make-up function can be improved. 本発明の構成によれば、シリンダに外力が作用することにより収縮しながら流出流量が多くなっても内側ばねによりメインポペットを閉鎖する外側ばねの弾性力が相殺されるため、タンク側の圧力が高くならず、メーキャップ機能が向上できる効果を奏する。 - 特許庁
An elastic tensile implement 3 in which one end of a linear member 33 is fixed to a proper place on the outer periphery of a drum 31 rotated by a spring 32 is provided in a casing 5, and a resisting means 4 for generating resistance T resisting an elastic force F of the spring 32 is provided. ゼンマイ32によって回転するドラム部31の外周適所に線状部材33の一端が固着されてなる弾性引張具3がケーシング5内に設けられると共に、前記ゼンマイ32の弾性力Fに抗する抵抗力Tを発生する抵抗手段4が設けられること。 - 特許庁
A cap 27 is fitted to the lower end part of each spring element 26, a plug 28 is fitted to and supported by the upper end part of each spring element 26, and each cap 27, and each plug 28 are brought into contact with an electrode 2 of the electronic circuit board 1 and an electrode 11 of the electrically connected object 10, respectively. そして、各スプリング素子26の下端部にキャップ27を嵌着し、各スプリング素子26の上端部に栓28を嵌着支持させ、各キャップ27を電子回路基板1の電極2に、各栓28を電気接合物10の電極11にそれぞれ接触させる。 - 特許庁
In this pedal crank device, when torque in a traveling direction is not applied to the pedal 12, a second crank member 11 is turned to the energizing member 13 side by a tension spring 20 through a spring catching member 18 and is abutted on the peripheral side end face of a cylinder part 13B of the energizing member 13. ペダル12に進行方向の回転力を負荷していない場合には、第2クランク部材11は、バネ引掛り部材18を介して引張りバネ20により付勢部材13側に回転させられ、付勢部材13の円筒部13Bの外周側端面に当接されている。 - 特許庁
Then, when the fine electric mechanical switch is approached to the closed state and the conductive layers 11 are compressed, restoring forces due to additional spring constants, k1,..., kn of the plurality of deformable conductive layers 11 are sequentially added to the restoring force due to the spring constant k0 of the beam 10. 次いで、微小電気機械スイッチが閉状態に近づき上記導電層11が圧縮されると、変形可能な複数の導電層11が有する追加のばね定数k1、・・・、knによる復元力が梁10のばね定数k0による復元力に順次加算される。 - 特許庁
The conductive parts 3 each have a spring part 33 capable of elastically deforming whose end 35a moves along a thickness of the sheet 2, an intermediate part 32 formed on the end 35a of the spring part 33, and a contact projection part 31 formed on the intermediate part 32 and protruding along the thickness of the sheet 2. 各導電部3は端部35aがシート2の厚さ方向に動くよう弾性変形可能なバネ部33と、バネ部33の端部35a上に形成された中間部32と、中間部32上に形成され、シート2の厚さ方向に突出する接触突起部31とを有する。 - 特許庁
When the IC 10 is pressed by an IC pressing means 54 to cause the bump 21 of the IC 10 to put a spring means S into deflective deformation through the film 3, a contacting pressure originating from the resilience of the spring means S is generated in the contacting part between the bump 21 and a contacting pad 11. ここで、IC10がIC押圧手段54によって押圧され、IC10のバンプ21が絶縁性樹脂フィルム3を介してバネ手段Sを撓み変形させると、バンプ21と接触パッド11の接触部にバネ手段Sの弾性力に起因する接触圧が生じる。 - 特許庁
The balancer 7 has casings 15, spiral shafts 16, nut members 18 screwed to the lower end sections of the spiral shafts 16, spring seats 19 installed at upper end sections in the casings 15 and torsion coil springs 17, in which one end sections are engaged with the nut members 18 and the other end sections with the spring seats 19 respectively. バランサ7は、ケーシング15と、スパイラルシャフト16と、スパイラルシャフト16の下端部に螺合するナット部材18と、ケーシング15内の上端部に装着されたばね座19と、その一端部をナット部材18に、その他端部をばね座19に、それぞれ係合した捩りコイルばね17と、を備える。 - 特許庁
A coil shaft of the coil spring, wherein the position facing the top of the solder ball 34 viewed from a solder ball 34 side is a center, is formed at a round shape, and the coil spring 30 makes the solder ball 34 bring into contact with the solder ball 34 on a coil outer periphery at a plurality of circumferential places where its top is a center. そして、コイルばね30のコイル軸をハンダボール34側から見てハンダボール34の頂部に臨む位置を中心とする円形に形成し、コイル外周部でハンダボール34にその頂部を中心とする円周状の複数箇所で当接するようにする。 - 特許庁
When the operation of the device is stopped, a second coil spring 33 formed from a shape memory alloy is stretched by the pressing force of a first coil spring 31 and the weight of an arm member 32, pressing force applied to the tension roller 20 decreases and consequently the intermediate transfer belt 22 slackens. 装置の稼動が停止しているときは、形状記憶合金からなる第2コイルスプリング33が、第1コイルスプリング31の付勢力やアーム部材32の自重により伸ばされ、テンションローラ20に印加される付勢力が低下し、中間転写ベルト22が緩んだ状態となっている。 - 特許庁
The spring forming machine 10 is capable of suppressing the effect on the feedback control caused by fluctuation of the measured coil length for each coil spring 91 and accidental abnormality value since the object of multiplying the correction gain of the feedback control is the average deviation ΔL of a plurality of continuous ones. 本発明のばね成形機10は、フィードバック制御の補正ゲインを乗じる対象を、連続した一定複数個平均の偏差ΔLとしたので、各コイルばね91毎の実測コイル長のばらつきや突発的な異常値によるフィードバック制御への影響が抑えられる。 - 特許庁
When the synchronizing sleeve 18 axially moves, a synchronizing spring 26 enters the first recess 28 simultaneously with the start of pushing-aside operation of a blocking ring 24 by the synchronizing sleeve 18, and the synchronizing spring 26 escapes from the first recess 28, before the synchronizing sleeve 18 contacts a dog tooth 12 of the transmission gear 14. シンクロスリーブ18が軸方向に移動するとき、シンクロスリーブ18によるブロッキングリング24の掻き分けの開始と同時にシンクロスプリング26が第1凹部28に進入し、シンクロスリーブ18が変速ギヤ14のドグ歯12に接触する前に、第1凹部28からシンクロスプリング26が脱出する。 - 特許庁
This auxiliary tool for the insertion device includes a body 100, a coil spring 200 attached to the body 100, and a plunger 300 provided vertically movably with respect to the body 100, and energized downwards together with the insertion device 600, by an energizing force of the coil spring 200. 挿入装置用補助器具は、本体100と、本体100に取り付けられたコイルばね200と、本体100に対して上下方向に移動可能に設けられ、コイルばね200の付勢力により挿入装置600とともに下方向に付勢されるプランジャ300とを備える。 - 特許庁
In the optical element driving apparatus 200 and the linear drive apparatus 100, a first spring member 91 and a second spring member 92 for generating a drag force when the movable body 5 is displaced by the magnetic drive mechanism 7 are provided between a fixed body 2 and the movable portion 5. 光学素子駆動装置200および直線駆動装置100において、固定体2と可動体5との間には、磁気駆動機構7により可動体5が変位した際に抗力を発生させる第1バネ部材91および第2バネ部材92が設けられている。 - 特許庁
The addition of the loose tightening spring 31 allows the device to decrease a displacement magnitude of a rod 11a swinging in a clockwise direction when compared to the single use of the upper spring 11, and suppress the decrease of energization force of a support portion 11c and suppress the decrease of the tension of the knit 17. 弛み取りばね31を付加することによって、天ばね11を単独で用いる場合よりも、竿11aが時計回り方向に揺動する変位量が少なくなり、支持部11cでの付勢力の低下を抑え、編糸17の張力低下を抑制することができる。 - 特許庁
To provide a liquid cleaning apparatus with which a bacterium such as Legionella pneumophila can be sterilized completely by breaking a cell wall of the bacterium without charging a sterilizing agent in water such as hot spring water, without deteriorating the bacterium removing effect and varying the water quality of water such as hot spring water. 温泉水等の水に殺菌剤を投与することなく、また、除菌効果の低下がなく、しかも温泉水等の水の水質を変化させずにレジオネラ菌等の細菌の細胞壁を破壊し、完全に死滅させることが可能な液体浄化装置を提供する。 - 特許庁
It makes the armature 15 recede from the rotor 19 by an elastic member 20 when the energization of the electromagnet 21 is shut off and a cylinder part 24 provided in its armature 15 fit in the switch spring 11, which prevents the diameter of the switch spring 11 from shrinking and the engagement error of the engagement element 8. 電磁石21への通電の遮断時に、弾性部材20によりアーマチュア15をロータ19から離反させ、そのアーマチュア15に設けた円筒部24をスイッチばね11の内側に嵌合させてスイッチばね11の縮径を防止し、係合子8のミス係合を防止する。 - 特許庁
Respective spring pieces have a root part 22a formed neighboring the substrate part and opposing to a part corresponding to the second contact part of the inner face of the intermediate part, and an inclined spring part 22b inclined and extended from the root part and opposing to a part corresponding to the first contact part of the inner face of the intermediate part. ばね片の各々は、基板部に隣接形成され中間部の内面の第2の接点部に対応する部分に対向した根元部22aと、根元部から傾斜して延び、中間部の内面の前記第1の接点部に対応する部分に対向した傾斜ばね部22bとを有する。 - 特許庁
The back part of the car body 1 of the floor washer and the squeegee 10 are connected using connecting bars 20, which are elastic and have universal joints 21 and 21 in both-end linking parts, and a centering mechanism, which consists of a tensile spring 23 and a spring lever 22, is established in the connecting bar 20. 床面洗浄機の車体1の後部とスキージ10の間を、伸縮自在で両端連結部分に自在継手21,21を設けた連結棒20を用いて連結すると共に、この連結棒20には引張りスプリング23とスプリングレバー22とから成るセンタリング機構を設ける。 - 特許庁
Since the spring shock absorbing body 2 normally help in the compressed condition is installed, the absorbing energy of the elevator shock absorber is increased without increasing the repulsive force of the spring shock absorbing body 2 and the stroke miniaturiation of the elevator shock absorber are reduced without increasing shock on elevator passengers. ばね緩衝体2を常時圧縮状態に保持し据え付けてあるので、ばね緩衝体2の反発力を大きくせずに、エレベータ用緩衝器の吸収エネルギーを大きくし、エレベータ乗客への衝撃を増大させず、エレベータ用緩衝器のストロークを短縮し、小型化できる。 - 特許庁
In this vehicular auxiliary machine driven through an electromagnetic spring clutch by the power from the drive source, the output hub 7 of the electromagnetic spring clutch is spline-fitted to the rotating shaft 8 of the vehicular auxiliary machine, and fastened axially by a mounting bolt 9. 駆動源からの動力によって電磁スプリングクラッチを介して駆動される車両用補機において、前記電磁スプリングクラッチの出力ハブ7が車両用補機の回転軸8に対してスプライン嵌合され、かつ取付ボルト9によって軸方向から締結されている。 - 特許庁
A detection value of a load cell 19 and that of a pulse encoder 18 are collected while imposing a load on the test piece TP by a servo motor 16 in between a state in which the counter value of the height counter 38 designates an initial spring height and a state in which it designates a predetermined maximum spring deformation amount. ばね高さカウンタ38のカウント値が初期ばね高さを示す状態と予め定めた最大ばね変形量を示す状態との間で、ばね供試体TPにサーボモータ16で負荷を与えながら、ロードセル19とパルスエンコーダ18の検出値を採取する。 - 特許庁
The bottom of the spring mount 4d is inserted into the notch 10b, a sliding protrusion 4g provided adjacent to the spring mount 4d is slidably in contact with the flexible substrate 10 near the notch 10b, and a recess 3a opposite to the notch 10b is provided on the fixed plate 3. そして、切欠き10b内にばね搭載部4dの底部を挿入すると共に、ばね搭載部4dに隣接して設けられた摺動突起4gを、切欠き10bの近傍でフレキシブル基板10に摺接させ、さらに固定板3に切欠き10bと対向する凹所3aを設けておく。 - 特許庁
In this conduit tube 1, a tube body 2 is composed of a long coil spring 6 and an insulating tube 4 covering the outside of the spring 6, and the insulating tube 4 has a radial thickness of 5 mm, and a resistance value of 50 MΩ or more when the impressed voltage is 250 V. チューブ本体2が、長尺なコイルバネ6と、このバネ6の外側に被覆される絶縁チューブ4とから構成され、この絶縁チューブ4は、その半径方向の厚さが5mmであって、且つ印可電圧が250Vの場合における抵抗値が50MΩ以上であるコンジットチューブ1。 - 特許庁
Thus when an offset frame 11 is moved from the right working position to a halfway position of the rightward movement, the repulsion of the second gas spring 30 is mainly used as an assist force, and with the repulsion of the first gas spring 20 also working additionally, a burden on an existing rocking cylinder is assisted. このため、右作業位置から右移動途中位置に向けてオフセットフレーム11を移動させる際には、主に第2ガススプリング30の反発力を補助力とするとともに、追加的に第1ガススプリング20の反発力も働きながら、既設の揺動シリンダにかかる負担を補助する。 - 特許庁
To provide a compact illuminated tactile switch capable of improving illumination efficiency of a switch part by irradiating a periphery of a center part of a plate spring with light emitted from a light emitting part at the shortest distance, and enabling to assemble and form the light emitting part and the plate spring compactly. 発光部から発せられる光を板状バネの中央部近辺に向けて最短距離で照射させることでスイッチ部の照光効率を高めると共に、前記発光部と板状バネとをコンパクトに組み込み形成することが可能な小型の照光式タクトスイッチを提供することである。 - 特許庁
A coil spring 12b is provided between connecting metal fittings 11d to which the base end of a whip element 11 is stuck and a base part metal fittings 12d, and a flexible braided wire 12c electrically bridging the fittings 11d and 12d is arranged inside the spring 12b. ホイップエレメント11の基端が固着された連結金具11dと、基部金具12dとの間にコイルスプリング12bが設けられており、このコイルスプリング12b内に連結金具11dと、基部金具12dとを電気的に橋絡する可撓性の編組線12cを配置する。 - 特許庁
To provide a printing device and a sheet feeding mechanism using a paper sheet cartridge capable of restricting properly the sheet feeding attitude including the sheet feeding direction using a spring, eliminating deformation of each sheet caused by the energizing force of the spring, and preventing the transporting force required after feeding the sheet from enlarging. 用紙カートリッジを用いる給紙機構において、バネを用いて用紙の給紙方向などの給紙姿勢を適切に規制することができるとともに、バネの付勢力によって、用紙の変形を生ぜず、また給紙後に必要な搬送力を大きくすることのないようにする。 - 特許庁
After mounting a slider 19 in the connector 17 slidably, one end of the board 20 is inserted into a gap defined between the slider and the spring terminal in a drawn state as shown by 19', and thereafter, the slider is pushed in, thereby pressing a conductive pattern on the terminal spring to obtain electrical connection. スライダ19をコネクタ部に摺動可能に組み付け、19′のごとく引き出した状態でスライダとばね端子の間に生じる隙間にフレキ基板20の先端を挿入し、スライダを押し込むことによりフレキ基板の導電パターンをばね端子に押し付けて電気的接続を得る。 - 特許庁
A hydraulic control valve 101 relatively increases a spring constant with the function of a spring 136 only to actively suppress self-exciting vibration when a valve opening is small and a relative distance between a valve seat 108 and a valve element 109 is in a region where the self-exciting vibration easily occurs. 液圧制御弁101においては、弁開度が小さく、弁座108と弁体109との相対距離が自励振動が発生し易い領域にあるときには、スプリング136のみが機能するようにしてばね定数を相対的に大きくし、自励振動を積極的に抑制する。 - 特許庁
In this three-way valve, pressure chambers of a piston 3 for energizing a first main valve in a valve closing direction with a spring 8 and a piston 16 for energizing a second main valve, resisting energizing force of the spring 13, are connected to a middle-pressure port B through a pilot valve and a pressure passage 25. 第1の主弁をスプリング8により閉弁方向に付勢するピストン3および第2の主弁をスプリング13の付勢力に抗して開弁方向に付勢するピストン16の圧力室をパイロット弁と圧力通路25を介して中圧ポートBに接続する。 - 特許庁
When a lever of the armrest 10 is not drawn, an arm 140 is urged backward of a frame 100 by a spring 143, and a ratchet 150 is not turned by a projection 142 of the arm 140, but urged by the spring 156 clockwise in plan view. アームレスト10のレバー11を引く操作をしていない状態では、アーム140は、スプリング143によりフレーム100の後部方向に付勢されているので、ラチェット150は、アーム140の突起142により回動されず、スプリング156により平面視、時計回りに付勢される。 - 特許庁
A filter element is also provided, so that it completely covers the filtration assistant line for spring type filters along the periphery of a cylindrical housing comprising a spiral spring around which an elastic wire with protrusions formed at irregular pitches is wound spirally and so that concave portions and projections of each wire are located at random. また、このバネ式フィルター用濾過助線を、等ピッチに突部を形成した弾力性を有する線材を螺旋状に巻回した巻バネからなる筒状筐体の外周に沿って完全に覆うようにかつ各線材の凹凸部がランダムに位置するよう設置したフィルターエレメントとする。 - 特許庁
To provide a fluid control valve in which repulsive force against pressing force from a pressure operating chamber is obtained by a compression coil spring and the compression coil spring and a primary-side fluid chamber are separated from each other by a diaphragm, capable of preventing secondary pressure from fluctuating even when primary pressure fluctuates. 圧力作用室からの押圧力に対する反発力を圧縮コイルバネにより得ており、且つ圧縮コイルバネと一次側の流体室とをダイアフラムによって区画している流体制御弁において、一次圧力に変動があっても二次圧力が変動しないようにする。 - 特許庁
The shutter 12 is held in a fixed state at the two positions where an operation part 7 of the equipment is opened and closed, by such a mechanism as the spring piece part 28a of a leaf spring 28 attached to the straight-moved shutter 14 is latchingly engaged in latching parts 30, 31, respectively. このシャッター12は、機器の操作部7を閉じた位置と開いた位置の二位置において直動シャッター部材14に取り付けられた板ばね部材28のばね片部28aが係合部30,31に夫々係合されることによりその位置で固定状態に保持される。 - 特許庁
This method is constituted of the steps of: providing a nominal die profile; deciding a spring back profile on the basis of the nominal die profile; and using a compensation method in order to decide the die profile on the basis of the nominal die profile and the spring back profile. この方法は、公称のダイプロファイルを提供する段階、公称のダイプロファイルに基づいてスプリングバックプロファイルを確定する段階、及び公称のダイプロファイルとスプリングバックプロファイルとに基づいてダイプロファイルを確定するために補償方法を用いる段階、から構成される。 - 特許庁
To provide a mold for molding capable of eliminating an evil due to use of a spring even without closing the mold by a vacuum suction force even without using a spring in a vacuum cavity mold of the type for vacuum evacuation when the mold is opened in a half-open state. 型が半開き状態にあるときに真空引きを行なうタイプの真空キャビティ金型において、スプリングを用いなくても型が真空吸引力によって閉じてしまうことがなく、もってスプリングの利用による弊害を解消することが可能な成形型を提供する。 - 特許庁
Consequently, the grease 79 can be prevented from projecting inward along the width from the gap among the reverse-side member 72, leaf spring member 50, and upper seal 74, and toner can be stopped from entering the gap among the reverse-side member 72, leaf spring member 50, and upper seal 74. これにより、グリース79が裏側部材72と板ばね部材50とアッパシール74との間の隙間から幅方向内側にはみ出すことを防止でき、また、裏側部材72と板ばね部材50とアッパシール74との間の隙間へのトナーの進入を阻止することができる。 - 特許庁
A hook part opening size of the tension spring is smaller than a retaining part size at mounting the tension spring onto the hook part. 食器を載置した食器かごを収納する洗浄槽を内部に有する食器洗浄機本体の開口部に設けられたドアが、引張ばねによりドアが閉まる方向に付勢力を与えられた食器洗浄機において、引張ばねのフック部開口寸法が、引張ばねのフック部の装着時の係止部寸法より小さくする。 - 特許庁
The vibration type compressor 1 is provided with a gas spring chamber 27, in which gas and liquid exist and of which inside capacity is changed to change the inner pressure when a movable member 38 moves, and an adjusting means 28 for adjusting amount of the liquid inside the gas spring chamber 27 in order to change frequency of the movable member 38. 内部に気体と液体とが存在していて可動部材(38)が移動すると内容積が変化して内圧が変化するガスばね室(27)と、可動部材(38)の振動数を可変とするためにそのガスばね室(27)内の液体の量を調節する調節手段(28)とを振動式圧縮機(1)に設ける。 - 特許庁
Servo control can be performed using the VCM actuator of the product, in order to prevent runaway of the VCM actuator, servo control is performed by balance of driving force of VCM and elastic force of a spring using a mechanism stopping an end part of the actuator mechanically and a mechanism pressing the end part by the spring. 製品のVCMアクチュエータを用いてサーボ制御をおこなうことを可能とし、VCMアクチュエータの暴走を防止するために、アクチュエータ端部を機械的に停止する機構とその端部をバネで押さえる機構を用い、VCMの駆動力とバネの弾性力の釣り合いでサーボ制御を行う。 - 特許庁
The hub 1 is composed of an inner hub 2 linked to the output shaft 5, the outer hub 3 linked to a drive plate 14 via the compression spring 17 and capable of relatively rotating a predetermined angle in regard to the inner hub 2, and a spring member 4 linking the inner hub 2 and the outer hub 3. 前記ハブ1を、出力軸5に連繋されるインナーハブ2と、圧縮ばね17を介してドライブプレート14に連繋され、インナーハブ2に対して所定角度相対回動可能なアウターハブ3と、これらインナーハブ2とアウターハブ3とを連繋するばね部材4とから構成する。 - 特許庁
To provide a front fork having a spring leg including a suspension spring constituted of springs without a damper, for securing smooth compression strokes with uniform flow path resistance to oil in an oil reservoir chamber, while avoiding impact based on a sudden change in the flow path resistance. ダンパを内蔵せず、ばねからなる懸架スプリングを内蔵するスプリング脚を有してなるフロントフォークにおいて、油溜室の油に及ぶ流路抵抗を可及的に一様にし、流路抵抗の急変に基づく衝撃を回避したスムースな圧縮ストロークを確保すること。 - 特許庁
A tension spring 7 for energizing in the bending direction is stretched between the first stay 5 and the second stay 6, and the second stay 6 side is provided with an operating lever 8 for displacing the first stay 5 and the second stay 6 about the connecting portion against the energizing force of the tension spring 7. また、前記第1ステー5と第2ステー6とに、互いに折れ曲がる方に付勢する引張ばね7を張設し、さらに、第2ステー6側に、前記引張ばね7の付勢力に抗して第1ステー5と第2ステー6とを、連結箇所を中心として変位操作するための操作レバー8を設ける。 - 特許庁
In the method of compressing the spring mattress 16, the spring mattress 16 is charged in a compression chamber and pressed from a direction parallel with an end face with a compression plate member 15 in the compression chamber, and cord members 11 are wound around the compressed mattress 16 to bind it. 圧縮室内にスプリングマットレス16を投入し、前記圧縮室内で圧縮板部材15でもって前記スプリングマットレス16を鏡面と平行な方向から圧縮し、その圧縮されたスプリングマットレス16の周囲に、紐部材11を巻き付けて結束する、スプリングマットレス16の圧縮方法。 - 特許庁
A shoe holddown mechanism of a drum brake is composed of a shoe holddown pin 10, shoe holddown spring 4, and a shoe holddown cup 11 at the tip of the pin, wherein one end 4a of the spring 4 is held unslidably by the web 2 of a brake shoe. シューホールドダウンピン10、シューホールドダウンスプリング4、シューホールドダウンピンの先端のシューホールドダウンカップ11等によって構成されるドラムブレーキのシューホールドダウン機構において、シューホールドダウンスプリング4の一端4aをブレーキシューのウェブ2に摺動不能に保持させて構成したドラムブレーキのシューホールドダウン機構。 - 特許庁