Four unit springs are connected to constitute a slide spring 22, and unit springs 25 and 26 are formed so that they may be shifted from unit springs 23 and 24 in the transverse direction. 単位バネが4つ連接されて摺動バネ22が構成されており、単位バネ23,24に対して、単位バネ25,26は横方向にずらされて形成されている。 - 特許庁
At one end of the shielding member 2, a coil spring 5 is installed which is to energize rotationally the shielding member 2 in such a way that its other end abuts to the rear seat. 遮蔽部材2の一端部には、遮蔽部材2の他端部がリヤシートに当接するように遮蔽部材2を回転付勢する弦巻ばね5が取り付けられている。 - 特許庁
The carriage 2 is fitted with a plate spring 9 which urges the elastic plate section 24 in the direction to drive the engaging protrusion 80 into the spiral groove 51 of a rotary shaft 5. また、キャリッジ2には、係合突起80が回転軸5の螺旋溝51内に食い込む方向に弾性板部24を付勢する板ばね9が取り付けられている。 - 特許庁
This paper feeding mechanism of a printer pushes a feed spring 8 against the recording sheet 5 and approaches a feed mechanism part 9 towards the paper feed roller 7 so as to raise the recording sheet 5. プリンタの給紙機構において、送り出しバネ8を記録紙5に押し付け、送り出し機構部9を給紙ローラ7に近づけることで記録紙5を持ち上げる。 - 特許庁
To provide the construction machinery capable of efficiency controlling a tilt type handle device and a spring-up console device when an operator gets on and off an operator's seat by interlocking both of them with each other. チルト式のハンドル装置と跳上げ式のコンソール装置とを連動させることにより、運転席への乗降時にこれらを効率よく操作できるようにする。 - 特許庁
The covers 20A, 20B are energized to the side of the surface 1a of the installation portion (the wall portion 1) by spring members 50A, 50B, and the cover 20A, 20B are pressed against the wall portion 1. カバー20A、20Bが、バネ部材50A、50Bによって設置部(壁部1)の表面1a側へ付勢され、カバー20A、20Bが、壁部1に圧接されている。 - 特許庁
A plate spring-like claw 11 having a sharp corner part is arranged around an operation device inserting hole of the operation panel 10, and is held and fixed by biting a side surface of the operation device 20. 操作盤10の操作装置差込穴の周囲に鋭利な角部を有する板バネ状の爪11を設け、操作装置20の側面を咥えて保持固定する。 - 特許庁
Furthermore, at the bottom of the receiving body 15 a spring-energized pusher 19 is mounted, and only by pushing the pusher 19 the engaging piece 8 can be easily removed from the engaging hole 22, so as to open the door. また受体の下部にはバネ付勢されたプッシャーが設置されており、プッシャーを押すだけで係合片を嵌合穴から容易に出して扉を開けることができる。 - 特許庁
A regulation portion 5 projected downward from the periphery of a though-hole 1b is provided on the lower surface side of a stator 1, so that the bending of a spring 3 is stabilized by this regulation section 5. ステータ1の下面側に貫通孔1bの周囲から下方へ突出した規制部5を設け、この規制部5でスプリング3の撓み具合を安定させたのである。 - 特許庁
Herein, the upper limit value is lower pressure than discharge pressure where the controlling spring 25 is broken or the plug 28 is pulled out, and it is set to be higher pressure than the regulated value. ここで、上限値は、復元バネ25の破損やプラグ28の抜け出しが生じる吐出圧力よりも低圧であって、規制値よりも高圧の値に設定されている。 - 特許庁
In this paper carrying device, when a cam 22 is rotated, a pivot member 13 connected to a spring 18 is vertically moved and a roller holder 6 having a pressuring roller 8 at the tip thereof is swung and displaced. カム22が回転すると、ばね18が連結する支点部材13が上下動し、且つ、先端に加圧ローラ8を有するローラホルダ6が揺動変位する。 - 特許庁
Additionally, the auxiliary wheel piece link 40 is energized in the front direction by a tension spring 70 both ends of which are engaged with the front link 20 and the rear link 30. 且つ前方リンク20および後方リンク30に両端を係止された引っ張りバネ70によって、補助車輪片リンク40が前方向へ付勢されている。 - 特許庁
This headrest has a link mechanism 10, a tensile spring Sa energizing it in the advancing turning direction, and a hook 30 retaining the link mechanism in the initial-position attitude state. リンク機構10と、これを進行の回動方向に附勢する引張ばねSaと、リンク機構10を初期位置の姿勢状態に保持するフック30とを有する。 - 特許庁
An operating member 13 having a pressure receiving wall portion 14 is arranged in the valve port 11, and a spring 15 is provided for energizing toward the valve chest 4 the operating member 13 to be moved forward. 受圧壁部14を有する操作部材13を弁口11内に配置し、操作部材13を弁室4方向に付勢して前進せしめるスプリング15を設ける。 - 特許庁
The middle ring member 20 rotates the light guide 2 around an optical axis by energizing force in the peripheral direction of the coil spring 30 to rotation pressurize contact the corner parts of the first end surface to the frame wall. 中間リング部材20がコイルスプリング30の周方向の付勢力によりライトガイド2を光軸回りに回転させて第1端面の角部を枠壁に回転圧接させる。 - 特許庁
Between a lower portion of a speed reducer T and a vehicle body frame F, a reducer side lower portion mount 71 is interposed so as to have a spring component at least in a vertical direction. 減速機Tの下部および車体フレームF間に、減速機側下部マウント71が、少なくとも上下方向のばね成分を有するようにして介設される。 - 特許庁
A valve element 645 is stored in a storage chamber 643 in a state of leaving clearance on the periphery, and is maintained in a valve opening state by a spring 646 when water is put in a resting state. 周囲に隙間を残した状態で弁体645を収容室643に収容し、水が静止状態であればバネ646により開弁状態に維持させる。 - 特許庁
In one embodiment, the MEMS interconnection pin has a pin base, two springs extending out from two different surfaces of the pin base, and a tip portion attached to each spring. 一実施形態において、該MEMS接続ピンは、ピンベースと、該ピンベースの2つの異なる面から伸びる2つのスプリングと、各スプリングに付着された先端部とを有する。 - 特許庁
At one end of the axis of winding 7 is connected to a spiral spring 8, and two sheets of lock gears 6 in piles are connected to the axis at the other end of the axis. 巻取軸7の一方の端部には渦巻きバネ8が連結され、他方の端部には2枚のロックギア6が重ねられた状態で同軸上に連結される。 - 特許庁
When a knob 30 is operated to be rotated so as to retreat a movable element 25, the resilient force of the compression coil spring 28 is weakened, and the kneading roller 16 can be separated from a swinging roller. 移動子25を後退させるように摘み30を回動操作すると、圧縮コイルばね28の弾発力が弱まり、練りローラ16が振りローラから離間可能になる。 - 特許庁
Frictional force generates to the gear 80 by a washer 143 being pressed by an energizing force of a disk spring 140, and the frictional force becomes a braking force of the rear wheel 26. 歯車80には、皿ばね140の付勢力でワッシャ143を押圧することにより摩擦力が発生し、この摩擦力が後輪26の制動力となる。 - 特許庁
An electrode part 253 at the other end of the resistive member 25 is pressed into the inner periphery of the cylindrical part 271 and is held by the urging force in the radial direction by the plurality of leaf spring parts. 筒状部271の内周に抵抗部材25の他端の電極部253が圧入され、複数の板ばね部272による径方向の付勢力によって保持される。 - 特許庁
Number of times when the operation position of the drive shaft 1 reaches the return operation completion position θSR are counted as number of times of spring return operation, and is updated and retained in a nonvolatile memory. このリターン動作終点位置θSRへの駆動軸1の動作位置の到達回数をスプリングリターン動作回数としてカウントし、不揮発性のメモリに更新保持させる。 - 特許庁
The module holding part 1 is supported so that it can move in a vertical direction and an inclined direction by an elastic part 5 such as a spring arranged between the part 1 and the moving part 4. モジュール保持部1は、移動部4との間に設けられたバネ等の弾性部5によって上下方向及び傾斜方向に移動可能に支持されている。 - 特許庁
To provide a valve seal structure unlikely to generate poor performance of sealing even if the valve element is inclined by eccentric acting of the fluid pressure or the load of a spring. 流体の圧力やばねの荷重が偏心的に作用することにより弁体が傾いても、シール不良が起こりにくくした弁のシール構造を提供する。 - 特許庁
Both the craw catching surfaces 21/31 in a door closing condition is inclined in an upward narrowing manner, thereby slipping up of the door spring 12 is restricted when the door 8 is opened. ドア閉じ状態における両爪受け面21・31を上すぼまり状に傾斜させて、ドア8を開放するときのドアばね12のずり上がりを規制する。 - 特許庁
The cylindrical member 37 is energized to the axial direction rear side by a spring 11, is brought into contact with the axial direction top end of the body 3 and forms a nozzle side low pressure path 44. 筒状部材37は、スプリング11により軸方向後方に付勢されて本体3の軸方向先端に当接し、ノズル側低圧路44を形成する。 - 特許庁
A spring 36 which biases a shaft 32 toward the periphery of the rotating table 10 is put inside the slide strip 30 to generate seizing force of the clamp claw 40. スライド片30の内部には、シャフト32を回転テーブル10の外周方向へ付勢するバネ36が挿入されおり、クランプ爪40の締め付け力を発生している。 - 特許庁
To provide a shift control device of a continuously variable transmission that prevents excessive force from being applied to a stepping motor while enabling increase of the thrust of a spring for backlash prevention. ガタ付き防止用のバネの推力の増大を可能にしつつ、ステッピングモータに過大な力が加わらないようにする無段変速機の変速制御装置を提供する。 - 特許庁
To provide a simply structured coiled spring which can adjust lateral force appropriately in the longitudinal direction as well as in the cross direction of a body while it is secured to a strut type suspension device. 簡単な構造で、ストラット型懸架装置への装着時に、車体の左右方向のみならず前後方向にも横力を適切に調整し得るコイルばねを提供する。 - 特許庁
As the balance 5 is elevated, the top thread T is pulled out of a bobbin through a thread tension device 12, when a thread take-up spring 13 is deformed by the tension force that acts on the top thread T. 天秤5の上昇により上糸Tがボビンから糸調子器12を通して引き出され、上糸Tに作用する張力で糸取りバネ13が変形する。 - 特許庁
The base body 2 is supported on a device main body 10 via a spring 6 so that the emitting surface 5b of the SIL 5 faces the signal recording surface 101 of an optical disk 100. 基体2は、SIL5の出射面5bが光ディスク100の信号記録面101に対向するようにばね6を介して装置本体10に支持される。 - 特許庁
The cleaning head 21 is held by a head holder 25 and a spring 24 is interposed between the head holder 25 and the transfer mechanism main body 20a of the head transfer mechanism 20. 清掃ヘッド21はヘッド保持体25により保持され、ヘッド保持体25とヘッド移送機構20の移送機構本体20aとの間にバネ24が介在されている。 - 特許庁
To provide a pigtailing machine that provides for a double pigtail while reducing cycle time, minimizes marking and assures an accurately formed double pigtailed coil spring. サイクル時間を減少させつつ二重ピグテールを与え、傷を最小に抑えて、正解に形成された二重ピグテールコイルバネを確保するピグテール形成機を提供する。 - 特許庁
The predetermined portion 20a is joined with the vibrating table 14 by a vibration transmitting part 28 having a plate-spring- shaped transmitting body 28a and a rubberlike transmitting body 28b arranged in series with each other. 板バネ状伝達体28a及びゴム状伝達体28bが直列した振動伝達部28により所定部20aと直進形振動テーブル14を連接する。 - 特許庁
A 1st leaf spring 28 of an energizing member 32 is allowed to be in elastic contact with a peripheral surface of the sub-guide shaft 2408 so as to energize the engaging part 2404 toward the focus direction. 付勢部材32の第1の板ばね28は、サブガイド軸2408の周面に弾接することにより、係合部2404を前記フォーカス方向に向けて付勢する。 - 特許庁
The lock/unlocking mechanism 67 for locking and unlocking a flipper 62 in a closed state to a telephone main body 61, is composed of a single locking member 68 and an auxiliary spring member 69. 閉じた状態のフリッパ62を電話機本体61にロック・ロック解除するロック・ロック解除機構67は、単一のロック部材68と、補助ばね部材69とよりなる。 - 特許庁
The pressing-down part 9a is formed in a plate shape so as to press down the bottom part upper surface 4d by substantially uniform pressurizing force by elastic force of the plate spring. 押付部9aは、板ばねの弾性力によって底部上面4dを略均一の加圧力によって押さえ付けるように平板状に形成されている。 - 特許庁
Then, the above contact terminals 40a-40x are fixed to the above movable and fixed housings and by separating both housings for a prescribed interval, the contact terminals 40a-40x are linked by the above spring. そして、上記可動及び固定ハウジングに上記接触端子40a〜40xを取付け、両ハウジングを所定間隔離して上記バネ体で連結する。 - 特許庁
The tips of the 1st beams 76b and 76b are connected by a 2nd lateral beam 72g, which is pressed by a press beam 69 provided in a pivot spring 68. また、第1ビーム76b、76b先端を第2横梁72gで連結し、第2横梁72gをピボットスプリング68に設けられた押圧梁69により押圧する。 - 特許庁
The balancer device is formed of the fixing shaft 13, the reel 12 for a wire 16, which is mounted on the fixing shaft 11 via the radial ball bearing 13, and a spiral spring 14 for energizing the reel 12 in a takeup direction. ラジアルボールベアリング13を介して固定軸11に装着するワイヤ16用のリール12と、リール12を巻取り方向に付勢するうず巻ばね14とを設ける。 - 特許庁
A compression coil spring 47 is arranged between the back-surface of the band guide 5 and a head segment 43, and then the head segment 43 of the pushing-out pin 45 is pushed against a back surface segment 55 of a pin receptor 41. 圧縮コイルスプリング47をバンドガイド5の背面と頭部43との間に配置し、押し出しピン45の頭部43をピン受け41の背面部55に押し付ける。 - 特許庁
A reaction receiving part 14 folded toward the support pin side is integrally formed in the pad spring 10, and this reaction receiving part 14 is allowed to elastically abut on the support pin 9. また、パッドスプリング10には支持ピン9側に向けて折曲げられた反力受部14を一体形成し、この反力受部14を支持ピン9に弾性的に当接させる。 - 特許庁
Since an outer peripheral surface of this guide pin 8a engages with an inner peripheral surface of a coil part 43 of this coil spring 40, a contact part of both these peripheral surfaces can be reduced. このガイドピン8aの外周面はこのコイルスプリング40のコイル部43の内周面と係合する為、これら両周面の接触部分を少なくできる。 - 特許庁
This supporting device includes a fixed supporting body (supporting body), a tubular rod 12 moving in an axial direction of the supporting body and a return spring 13 between the supporting body and the rod 12. 本装置には、固定支持体(支持体)と、該支持体の軸方向に移動する管状ロッド12と、上記支持体とロッドとの間の戻りバネ13と、を備える。 - 特許庁
A plate spring 30 to be elastically deformed by a load in the longitudinal direction of the vehicle body is provided between the engagement part 28 of the seat back retainer 24 and the seat back 16. シートバックリテーナ24における係合部28とシートバック16との間には、車体前後方向の荷重によって弾性変形する板ばね部30が設けられている。 - 特許庁
A bearing 36 for retaining the rotation shaft 33 is urged to a direction leaving from the driving roller 16 by a compression spring 37 and a tension is imparted to the conveying belt 15. 回転軸33を保持する軸受36を、圧縮ばね37により駆動ローラ16から遠ざかる方向に付勢し、搬送ベルト15に張力を付与する。 - 特許庁
Stiffness of a stabilizer body 7 is guaranteed by a plate spring 8 in the constitution and connecting plugs 9 at both ends are connected with support pins having a round center to brackets 10. スタビライザ本体7の剛性は皿ばね8が担保する構造とし、両端のコネクティングラグ9を中央部が球状の支持ピン11でブラケット10に接続する。 - 特許庁
When an opening angle formed by the cover 15 and the back cover 16 is enlarged up to 90 degrees, both ends of the screen sheet 11 are biased by the opening spring 27 and are pulled to form a flat surface. 表紙15及び裏表紙16がなす開き角度を90°まで開くと、開きバネ27により付勢され、スクリーンシート11の両端が引っ張られて平面になる。 - 特許庁
An upper end and a lower end of the connection lever 4 are connected to the upper and the lower hook members 5 and 6, and a coil spring 19 to drive the hook members 5 and 6 to the locking side is attached to the connection lever 4. 連結杆4の上端と下端が上下の鉤部材5,6に連結され、連結杆4に鉤部材5,6を施錠側に付勢するコイルばね19が装着される。 - 特許庁