「Spring」を含む例文一覧(40241)

<前へ 1 2 .... 530 531 532 533 534 535 536 537 538 .... 804 805 次へ>
  • With the projecting operation of the shift rod, the sliding rod of the pallet locking device is pushed to rise against the energizing force of the coil spring, and the hook in the lock position is tilted to release the lock of the pallet.
    前記シフトロッドの突出動作でパレットロック装置の摺動ロッドをコイルバネの附勢力に抗して押して起立してロック位置にあるフックを傾倒してパレットのロックを解除する。 - 特許庁
  • A rotation stopper to a housing 6 of a ball spline outer cylinder 4 is formed by fitting a plate spring key 14 in a key groove 4a of the ball spline outer cylinder 4 and a key groove 14a of the housing 6.
    ボールスプライン外筒4のハウジング6に対する回り止めは、板ばね製のキー14がボールスプライン外筒4のキー溝4aおよびハウジング6のキー溝14aに嵌め入れられることで形成されている。 - 特許庁
  • To provide a nonflammable plate for an automobile ashtray and its manufacturing method smoothly carrying out edge removal of a tip and easily and positively providing a spring effect to the whole.
    先端のエッジ除去が滑らかに行われ、全体のスプリング効果の付与も簡単かつ確実に行われた自動車用灰皿の防炎板及びその製造方法を提供する。 - 特許庁
  • A brim 19 is formed integrally on one end of the piston rod 11 and a compression coil spring 14 is installed elastically between this brim 19 and the valve 13 for closing the suction port 16.
    ピストンロッド11の一端には鍔19が一体に形成され、この鍔19と吸引口16を閉鎖するバルブ13との間には、圧縮コイルばね14が弾装されている。 - 特許庁
  • To provide an armature spring which drives an armature and presses the armature toward a bearing, and which is suitable for a large rotation angle for the armature in spite of a compact size.
    アーマチュアを付勢するのみならず、軸受に対してアーマチュアを押圧し、アーマチュアの大きな回転角度に好適であり、にもかかわらずコンパクトな寸法を特徴とするアーマチュアばねの提供。 - 特許庁
  • A bottom plate elevating mechanism 30 is composed of a bottom plate elevating act 7, links 10a and 10b, lever 12, link spring 26, etc., and raises a bottom plate 6 gradually interlocking with insertion of a cassette 5.
    カセット5の挿入に連動して底板6を徐々に持ち上げる底板上昇機構30(底板上昇アーム7、リンク部材10a,10b、レバー12、リンクスプリング26等)を設ける。 - 特許庁
  • When the feed of the cutting oil is stopped during the cutting, the piston 16 is retracted by the contraction of the coil spring 22, and as a result, the end mill 14 with the hole is detached from the work.
    切削加工途中に切削油の供給が停止されると、コイルスプリング22の収縮作用下にピストン16が後退動作し、その結果、穴付エンドミル14がワークから離脱する。 - 特許庁
  • Then, when the handling chuck opens the disk member 1 and is raised, the guiding member 3 is pushed up by the spring 4 to close the chucking member 2, and the disk member 1 is thereby chucked.
    次に、ハンドリングチャックがディスク部材1を開放して上昇すると、バネ4によってガイド部材3が押し上げられることによりチャック部材2が閉じ、ディスク部材1をチャックする。 - 特許庁
  • The pressure mechanism 40 is equipped with a piston 60 for pressing the balloon 30, a lock pipe 70 for compressing a first spring 41 to energize the piston 60, and the button 80 for pushing the lock pipe 70.
    加圧機構40は、バルーン30を押圧するピストン60と、第1ばね41を圧縮させてピストン60を付勢するロックパイプ70と、ロックパイプ70を押すボタン80とを備える。 - 特許庁
  • To provide a synchronization device of a throttle valve capable of always properly keeping synchronization of mutual adjacent throttle valves, by preventing sticking of dust to a synchronization bolt and a set spring.
    同調ボルト及びセットばねへのダストの付着を防ぎ,隣接するスロットル弁相互の同調を常に適正に保つことを可能にしたスロットル弁の同調装置を提供する。 - 特許庁
  • To suppress positional deviation of a bracket even if a spring back phenomenon occurs when bending is applied to an end plate to fix the bracket, and thus, enhance accuracy of the mounting position of the bracket.
    エンドプレートに曲げ加工を施してブラケットを固定する場合に、スプリングバック現象が発生してもブラケットの位置ずれを抑制できるようにして、ブラケットの取付位置の精度を高める。 - 特許庁
  • To provide a paper aligning apparatus and an image forming apparatus equipped with the paper aligning apparatus capable of reducing damage done to paper in configuration of a loop roller axially movable by spring energization.
    スプリング付勢による軸方向可動のループローラの構成において、用紙に与えるダメージを軽減できる用紙整合装置、およびこれを備えた画像形成装置を提供する。 - 特許庁
  • A coil spring 22 is compressed and a piston rod 28 displaces upward although the piston rod 28 is retracted into a cylinder 26 when the impact acts on the cylinder 26 and the cylinder 26 displaces upward.
    シリンダ26に衝撃が加わりシリンダ26が上方へ変位すると、コイルスプリング22は圧縮され、ピストンロッド28はシリンダ26内に没入するもののピストンロッド28も上方に変位する。 - 特許庁
  • To provide an Ni saving type inexpensive austenitic stainless steel for a spring which has excellent manufacturability and mechanical strength and has excellent ductility and formability even when high strength is imparted thereto by rolling.
    製造性や機械的強度に優れ、圧延によって高強度を付与されても、延性及び成形性に優れた省Ni型の安価なばね用オーステナイト系ステンレス鋼を提供する。 - 特許庁
  • To provide a shot-peening apparatus capable of keeping the posture of a cylindrical metal product such as a coil spring and executing the consistent shot-peening, and a shot-peening method using the same.
    コイルばねなど円筒型の金属製品の姿勢を保ち安定したショットピーニング処理を施すことができるショットピーニング装置とこれを用いたショットピーニング方法を提供する。 - 特許庁
  • To provide a vibration control device effectively attenuating both of engine shake vibration and idling vibration, and effectively inhibiting increase of dynamic spring rate in acceleration travel of a vehicle.
    エンジンシェイク振動およびアイドリング振動のいずれをも効果的に減衰させ、また車両の加速走行時の動的ばね定数の増加を有効に抑制できる防振装置を提供する。 - 特許庁
  • The FRP spring 1 has a layered structure (having a code 20 for three layered structure, and a code 30 for five layered one) wherein plurality of fibers having different tensile elastic moduli are layered.
    FRPばね1は、引張弾性率が異なる複数の繊維が積層された積層構造(3層構造の場合には符号20,5層構造の場合には符号30)を有する。 - 特許庁
  • An actuator is rotatable about a second axis spaced from the first axis to move the stand away from its supporting position against the biasing force of the torsion spring.
    アクチュエータは、捩りバネの付勢力に対してスタンドをその支持位置から離れるように移動させるために第1軸線から離間した第2軸線の周りで回転可能である。 - 特許庁
  • The torque limiter device 1 includes a flywheel 5, a clutch disc assembly 6, a cover plate 34, a pressure ring 32, a plurality of friction materials 26, a plurality of rivets 36, and a cone spring 33.
    トルクリミッタ装置1は、フライホイール5と、クラッチディスク組立体6と、カバープレート34と、プレッシャリング32と、複数の摩擦材26と、複数のリベット36と、コーンスプリング33と、を備えている。 - 特許庁
  • A manually operable release element is configured to substantially simultaneously move the release leg of each of the torsion springs in a direction to unwind the coil portion of each spring from about the axle.
    手動で操作可能な解除要素は、ねじりばねのそれぞれの解除脚部を、軸体の回りから各ばねのコイル部分を解く方向に実質的に同時に動かすように構成される。 - 特許庁
  • To provide a fuel injection pump device preventing lubrication oil from a lower housing side from being mixed into fuel oil by further improving close contact properties between a lower spring receiver and a tappet.
    下部バネ受けとタペットとの更なる密着性の向上を図り、下部ハウジング側からの潤滑油が燃料油に混入することを防止した燃料噴射ポンプを提供する。 - 特許庁
  • Thereby play by elastic force of the coil spring 73 is provided between the head 71a and the heat sink 6, and the covered electrodes 3 are allowed to deform.
    これにより、頭部71aと放熱器6との間に、コイルばね73の弾性力による遊びを持たせることができ、被覆電極3が変形する余地を持たせることができる。 - 特許庁
  • To provide a structure capable of achieving reduction of the number of components and miniaturization of a lens barrel, and preventing deformation of a barrier blade due to tension of a barrier driving spring.
    部品点数の削減とレンズ鏡筒の小型化を達成することができるとともに、バリア駆動ばねの張力によるバリア羽根の変形を防止することができる仕組みを提供する。 - 特許庁
  • In the front of this lead tank, a chuck guide 20 having a chuck 29 is provided movably in the axial direction and pressed rearward with a weak chuck spring 26 installed between the inner faces of the shaft cylinder.
    この芯タンクの前部には、チャック29を有するチャックガイド20が軸方向に移動可能に設けられ、軸筒の内面間に設けた弱いチャックスプリング26で後方に押されている。 - 特許庁
  • By interlocking with the turning operation, the plate spring 8 oscillates with the output shaft 7 as a rotary shaft, while repeating bending, and the output shaft 7 reciprocatively rotates by interlocking with the oscillation.
    この旋回動作に連動して、板バネ8が撓曲を繰り返しながら出力軸7を回転軸として揺動し、この揺動に連動して出力軸7が往復回転する。 - 特許庁
  • The first restriction ring 43 is configured to be elastically deformed by the pressing force of the compression coil spring 39 to allow the contact between the side plate 36 and the friction plate 34.
    第1規制リング43は、圧縮コイルばね39の押付力により弾性変形してサイドプレート36と摩擦板34との接触を許容するように構成されている。 - 特許庁
  • This reverse flow tolerant spring activated brush seal structure (110) restricts the transfer of a pressurized fluid (160) between a first chamber (140) and a second chamber (145) along a movable shaft (150).
    可動シャフト(150)に沿った第1のチャンバ(140)と第2のチャンバ(145)との間の加圧流体(160)の移動を制限する逆流耐性バネ作動ブラシシール構成(110)。 - 特許庁
  • The reaction when the door D is closed can be absorbed by the movement of the base 30 along the bolt 31 and an action of an elastic repulsive force by shrinkage of the coil spring 33 at the time of its movement.
    扉Dが閉まる際の反動は、ベース30のボルト31に沿った移動およびその移動の際のコイルバネ33の収縮による弾性反発力の作用により吸収できる。 - 特許庁
  • To provide a reclining sofa bed naturally starting reclining by spring force and raising a foot stand at the same time when the body is raised by flying rings to be inclined to have four bending points between five surfaces.
    つり輪で身体を持ち上げるとバネの力で自然にリクライニングが始まり同時に足の台も上がってきて4屈折5面に角度のつくリクライニング式ソファー・ベッドを提供する。 - 特許庁
  • To provide a valve stem seal that can obtain large resistance to a cyclical force applied by a valve spring which cracks a flange of a valve stem seal or a valve stem seal assembly.
    バルブステムシールまたはバルブステムシール組立体のフランジにクラックを引起こすバルブスプリングにより加えられる周期的な力に対する大きな抵抗が得られるバルブステムシールを提供する。 - 特許庁
  • To effectively suppress the self-excited oscillation of a table when machining a large or long member by building a weight connected by using a spring and a damper inside the table.
    テーブルの内部にばねと減衰器を用いて接続された錘を内蔵することで,大形あるいは長尺の部材を加工する際のテーブルの自励振動を効果的に抑制する。 - 特許庁
  • The lid 6 is mounted on the optical fiber 8 mounted on the optical fiber installing groove, and the lid 6 is pressurized onto the substrate 5 having the optical fiber installing groove by the spring member 7.
    光ファイバ設置溝に搭載した光ファイバ8の上には蓋6が搭載され、蓋6は光ファイバ設置溝が形成された基板5にバネ部材7により押圧されている。 - 特許庁
  • The pressurizing member 6 is so arranged that the spring member 61 is disposed in the insertion opening 52 as viewed from the stacking direction X and the press plate 62 is fixed on the frame 5.
    加圧部材6は、積層方向Xから見たときバネ部材61が挿入開口部52の内側に配置され、押圧板62がフレーム5に固定された状態で配設されている。 - 特許庁
  • The straightening roller moving mechanism 5 is locked to the locking frame 6, and a spring 23 is interposed between the locking frame 6 and the slide member 15 in a compressed manner.
    矯正ローラ移動機構5は、係止用フレーム6に係止できるようにしてあり、又、上記係止用フレーム6とスライド部材15との間には、ばね23が圧縮されて介装されている。 - 特許庁
  • To provide an induction heating cooker capable of suppressing occurrence of uneven heating by suppressing simultaneous occurrence of resonance of a support spring to keep a constant spacing between induction heating coils and the top plate.
    支持スプリングの共振の同時発生を抑制することで、誘導加熱コイルとトッププレートとの間隔を一定に保持し、加熱ムラの発生を抑制できる誘導加熱調理器を提供する。 - 特許庁
  • At this point, the leading end of a slider 45 moves over a first inclining face 51 formed on the handle 36a, and is pushed inside a frame side plate 23a against the biasing force of the coil spring 47b.
    このとき、スライダ45の先端がハンドル36aに形成された第1傾斜面51に乗り上げ、コイルバネ47bの付勢力に抗してフレーム側板23a内に押し込まれる。 - 特許庁
  • To stably obtain large component supply capacity in a vibrating type component feeder for carrying components by amplifying the vibration of a vibration mechanism by a two-stage plate spring.
    加振機構の振動を2段の板ばねで増幅して部品を搬送する振動式部品供給装置において、大きな部品供給能力が安定して得られるようにする。 - 特許庁
  • A tension coil spring 14 is provided between an exhaust tail pipe 12 and a lid member 13 to always provide elastic force in the direction of closing an exhaust port 12D with respect to the lid member 13.
    排気尾管12と蓋体13との間には、蓋体13に対し排気口12Dを閉じる方向への弾性力を常時付与する引張りコイルばね14を設ける。 - 特許庁
  • When receiving the pin lock invalidation command from an operation panel 5 or the velocity comparator 42, a pin lock controller 43 controls a pin device 26 to store a pin 26a projecting by a spring force.
    ピンロック制御器43は、操作パネル5あるいは速度比較器42よりピンロック無効指令を受信するとピン装置26を制御し、バネ力で突き出しているピン26aを格納させる。 - 特許庁
  • To provide a new placement method for easily and reliably performing placement work when placing (fixing) a heat sink to a circuit board by using a spring member.
    ヒートシンクをスプリング部材を用いて回路基板に装着(固定)するにあたり、この装着作業が簡易な操作で且つ確実に行えるようにした新規な装着手法を提供する。 - 特許庁
  • To provide the plug socket of an ignition coil for an internal combustion engine, suppressing occurrence of minute corona discharge and also preventing fall of a coil spring, by an extremely simple structure.
    極めて簡単な構造によって、微小なコロナ放電の発生を抑制すると共にコイルスプリングの落下を防止することができる内燃機関用点火コイルのプラグソケットを提供すること。 - 特許庁
  • He then added, "We started in spring training with a dream. Our dream was to be in the last game of the season, and here we are, and we won the game."
    そして「我々は1つの夢を持って春季キャンプに入った。我々の夢はシーズン最後の試合に出場することだった,そして我々はここにいてその試合に勝ったのだ。」と加えた。 - 浜島書店 Catch a Wave
  • "We want to enter the next Summer Koshien. I want to stay in good condition through the Spring Koshien and see how well I can do," said Tanaka.
    「僕たちは次の夏の甲子園に出場したいと思っています。僕自身は春の甲子園を通じて良いコンディションを維持し,どこまでできるか見たいです。」と,田中投手は語った。 - 浜島書店 Catch a Wave
  • Saito Yuki, 18, of Waseda University appeared as the starting pitcher in an opening game of the Tokyo Big6 university baseball spring championship at Jingu Stadium on April 14.
    早(わ)稲(せ)田(だ)大学の斎藤佑(ゆう)樹(き)投手(18)が,4月14日の神宮球場での東京六大学野球春季リーグ戦の開幕試合に先発投手として登板した。 - 浜島書店 Catch a Wave
  • He pitched the first complete-game shutout in the finals of a high school tournament at Koshien since Matsuzaka Daisuke, then of Yokohama High School, did it in both the spring and summer tournaments in 1998.
    彼は,横浜高校(当時)の松(まつ)坂(ざか)大(だい)輔(すけ)投手が1998年の春夏両大会で達成して以来初めて,甲子園での高校大会決勝で完投完封を果たした。 - 浜島書店 Catch a Wave
  • A manual starting lever 181 with a reset spring mechanically interlocked with a fuel bypassing manual valve 132, the main circuit switcher 171, and a rotary shaft of the air blower 41 are provided.
    燃料バイパス手動弁132、主回路切替器171、および空気ブロア41の回転軸と機械的に連動する復帰バネ付き手動型起動レバー181が設けられる。 - 特許庁
  • The anchor head 3 is rotatable between an insertion position and a locking position with respect to the screw rod 2, and preset to the insertion position by spring force, however automatically rotates to the lock position when released from the force.
    アンカーヘッド3は、ねじ棒2に対して挿入位置と、ロック位置との間で回転自在であり、ばね力で挿入位置にプリセットされるが、解放されるとロック位置に自動回転する。 - 特許庁
  • A second cam gear 22 is rotated about a second shaft 1d that is so formed on the shutter bottom board 1 as to become parallel to the first shaft 1b, to charge a blade-driving spring 14.
    第2のカムギヤ22は第1の軸1bと平行となるようにシャッター地板1に形成される第2の軸1dを中心として回転することで羽根駆動バネ14をチャージする。 - 特許庁
  • To control the reaction of a contact spring when a movable contact is opened in a contact device having the movable contact bridging a pair of fixed contacts disposed opposite to each other.
    対向配置された一対の固定接触子間を橋絡する可動接触子を有する接触子装置において、可動接触子開離時における接触スプリングの反力を抑える。 - 特許庁
  • This contact 1A is provided with a metal spring film 2A exerting elastic force, and a metal contact film 3 having a ridge line 3a by individually forming them independently of each other (fig. 3, K).
    本発明の接触子1Aにおいては、弾性力を発揮する金属ばね膜2Aおよび稜線3aを有する金属接触膜3を別個独立に形成して備える(図3K)。 - 特許庁
<前へ 1 2 .... 530 531 532 533 534 535 536 537 538 .... 804 805 次へ>

例文データの著作権について

  • 浜島書店 Catch a Wave
    Copyright © 1995-2026 Hamajima Shoten, Publishers. All rights reserved.
  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.