The stopper e2 is energized in an arrow mark T1 direction by a twist coil spring e3, an upper surface e2-4 of the stopper e2 collides with a lower place part of a cover d1, and rotation of the stopper e2 is stopped. ストッパe2は、ねじりコイルばねe3により矢印T1方向への付勢され、ストッパe2の上面e2−4が、蓋d1の下面部にぶつかり、ストッパe2の回動は停止する。 - 特許庁
The contact point contact unit 37 is rockably supported, with the pins 42 serving as the rocking center, and a coupling section 44 is retreated from a card passage 10 by a tensile coil spring 48. 接点接触ユニット37はピン42を揺動中心として揺動自在に支持され、引張りコイルばね48によって、係合部44がカード通路10から退避している。 - 特許庁
A motive power transmission shaft urging spring 43 for urging the motive power transmission shaft 35 to a direction for connecting it to the drive shaft 31 is provided between the motive power transmission shaft 35 and the clutch housing 33. 動力伝達軸35とクラッチハウジング33との間に動力伝達軸35を駆動軸31に連結する方向に付勢する動力伝達軸付勢ばね43を設ける。 - 特許庁
The SD card slot 6a is provided with an opening 7 in a size corresponding to the SD card on the front face, a spring 8 is arranged at the lower side, and a contact 9 is arranged at the upper part. SDカードスロット6aは、SDカードに対応させた大きさの開口部7を前面に有し、その下側部にバネ8を配置すると共に上部にコンタクト9を設ける。 - 特許庁
A safety cover 13 is turnably mounted at the tip of a fixed blade 3 so as to be normally retained in a position to close a blade tip opening 19 by the urging force of a spring 15. 固定刃3の先端部に安全カバー13を回動可能に取り付け、かつ通常は刃先開口部19を閉塞する位置にスプリング15の付勢を利用して留まるようにした。 - 特許庁
The cleaning member 52 in a thin plate form, which swings around a swing center C, is disposed in a retracting position in contact with an opening/closing cover (not shown in a figure) located in a closed position by the tensile metal spring 64. 揺動中心Cに揺動する薄板状の清掃部材52を、金属性の引っ張りばね64によって閉位置にある開閉カバー(不図示)に当接させて退避位置に配置する。 - 特許庁
The three-way shielding body 23 is constantly locked by a lock mechanism 24 and, when the lock of the lock mechanism 24 is released, it is pushed toward the side of the landing door 9 by the spring 25. 常時三方遮へい体23は係止機構24によって係止され、係止機構24の係止が解除されると、スプリング25により乗場ドア9側へ押圧される。 - 特許庁
A lock housing 23 of the lock mechanism 20 is provided with a shaft support part 23 at lock side for journaling a coil part 22a of an open lever spring 22 that urges the open lever 21 toward the initial position. ロック機構20のロックハウジング23には、オープンレバー21を初期位置に向けて付勢するオープンレバースプリング22のコイル部22aを軸支するロック側軸支部23が設けられている。 - 特許庁
The sliding member 21 is formed in a flat plate shape, and an engagement portion 21B engaging with the hook and a supporting member 22 having a long hole 23 where the spring bar 15 penetrates are formed in the flat plate section. スライド部材21が平板状に形成され、その平板部にはフックと係合する係合部21Bと、ばね棒15が貫通する長孔23を有する保持部22とが形成される。 - 特許庁
Since the restoring force at bending of the resin spring part 3 is added to the restoring force of the terminal plate 2, the abutting part 2b of each terminal plate 2 will be surely pressed against the terminal part of the camera module 5. 樹脂バネ部3が撓んだときの復元力が端子板2の復元力に加わり、カメラモジュール5の端子部に各端子板2の当接部2bが確実に押し当てられる。 - 特許庁
The lens frame 48 for a lens 26A to be adjusted is energized toward an optical axis by a corrugated spring 50 and a pressure ring 52 so as to be freely rotatably supported in the lens barrel 10. 調整の対象となるレンズ26Aのレンズ枠48は、波板バネ50と押さえ環52とによって光軸方向に付勢され、レンズ鏡筒10内に回動自在に支持される。 - 特許庁
When positioning the base guide to the socket, the pushing part 20 is moved in a direction separated from one face of the base guide by moving the grip 30 against urging of the spring member 40. ソケットに対してベースガイドを位置決めしたとき、グリップ30をバネ部材40の付勢に抗して移動させることにより押圧部20がベースガイドの一方の面から離れる方向に移動する。 - 特許庁
The support spring 26 is provided between a fixed bracket 25 fixed to the peripheral surface of the flywheel device 11 and a support bracket 24 provided in an upper end of a support 22 stood from the base 21. フライホイール装置11の外周面に固定された固定ブラケット25と基台21から立設された支柱22の上端の支持ブラケット24との間に支持バネ26を設ける。 - 特許庁
The heart cam type lock mechanism 5 includes a plate spring 12 continued to the front side of a slider 7, which is elastically curved in a direction orthogonal to the opposed broad faces 3a of the card insertion passage 3. ハートカム式ロック機構5は、スライダー7の手前側の部分に、カード挿入通路3の対向する広面3aに直交する方向に弾性的に曲がる板バネ12を連設する。 - 特許庁
To provide equipment and a method for examining a durometer hardness meter, in which a spring force generated for the ascending amount of a push needle in the durometer hardness meter can be examined accurately. デュロメーター硬度計の押針の上昇量に対して生じるばね力の検定を正確に行うことができるデュロメータ硬度計の検定装置及び検定方法を提供する。 - 特許庁
The H-spring 112 applies the bias force, and so at least one of the friction pads 104a, 104b is always pushed against the torque supports 108a, 108b in the direction of the reaction of braking force. また、Hばね112がバイアス力をかけるため、摩擦パッド104a,104bのいずれかは制動力の反力の方向にあるトルク受け108a,108bに常に押接される。 - 特許庁
Since the time when bilevel mode is selected is spring and autumn, the middle season of the year usually, both of a rear seat cooler unit and a rear seat heater unit do not require the maximum cooling and heating capacity. バイレベルモードを選択する時期は通常、春秋の中間シーズンであるため、後席クーラユニットと後席ヒータユニットが両方とも最大冷暖房能力を必要としない。 - 特許庁
A first holding body 10 and a second holding body 20 are coupled to each other freely to swing through a connection part A, and a torsion spring S is provided to energize holding ends 11 and 21 of these holding bodies. 第1挟持体10と第2挟持体20とを連結部Aで揺動自在に連結し、これらの挟持端部11、21を閉じ方向に付勢するトーションバネSを備える。 - 特許庁
The guide part 50 includes at least one guide spring part 60 that slidably contacts with the periphery part of the external member 20 to hold down the external member 20 to the inside of the guide part 50. 案内部50は、外装部材20の外周部にスライド可能に接触しつつ、外装部材20を案内部50内に向けて押えるガイドバネ部60を少なくとも1つ有する。 - 特許庁
Since the inside of a container 22 does not need to be pressurized, the container 22 can easily be manufactured and a compressing means such as a strong spring is disposed with, to miniaturize the entire device 1. しかも、容器22の内部を高圧にする必要がないので、容器22の製造が容易となるとともに、強力なバネ等の圧縮手段が不要となり、装置1全体の小型化が図れる。 - 特許庁
An elastic constant of the lower spring 86 is lower when the disk 74 is in a second position where the magnetic member is closer to the neutral position than a first position as compared with the case in a first position. ロアスプリング86の弾性定数は、ディスク74が第1の位置にあるときよりも磁性部材が第1の位置よりも中立位置に近い第2の位置にあるときのほうが小さい。 - 特許庁
On the other hand, by pushing an operation section 9 in a direction of the arrow R2, the friction member 7 is detached from the side face of the shaft 3 and an energizing force by the compression coil spring 2 slides the shaft 3 downward. 一方、操作部9を矢印R2方向に操作すると、摩擦部材7がシャフト3の側面から離れ、圧縮コイルバネ2の付勢力によりシャフト3が下方にスライドする。 - 特許庁
Whereby a spring constant in the total pneumatic tire can be ensured by increasing the rigidity of the side part at one side, even when the rigidity of the side part at the other side is decreased, and the steering stability can be ensured. このため、片側のサイド部剛性を小さくしても、もう片側のサイド部剛性を大きくして、空気入りタイヤ全体でのバネ定数を確保でき、操縦安定性を確保できる。 - 特許庁
A recess 21 for allowing the coil spring 17 to be fitted into the head part of the holding projection 16 in an inclined state is formed in the axial part 16a approaching the head part of the holding projection 16. 保持突起16の頭部と近接する軸部16aには、コイルスプリング17を傾斜状態で保持突起16の頭部に嵌合するのを許容するための凹部21を形成する。 - 特許庁
This disk recording/playing device is constructed in such a manner that a cartridge 60 appears and disappears, and a spring piece 65 for pressing the cartridge 60 to a chassis is attached to a holder 3 attached to the chassis so as to be moved vertically. ディスク記録又は再生装置は、カートリッジ60が出没し、シャーシ1に対し昇降自在に取り付けられたホルダ3に、カートリッジ60をシャーシ1に付勢するバネ片65を取り付ける。 - 特許庁
Consequently, load of elasticity of the spring 18 or higher is not applied even if the finger f is caught in the rear arm rest if the same has a size within stroke of the movable part 14 (black arrow mark in a figure). これによって、可動部14のストローク(図中黒矢印)内に収まる大きさであれば指fなどが挟まってもバネ18の弾性以上の荷重が掛かることはない。 - 特許庁
The spring piece 22 is fixed to a rear end surface of a cheekblock, and a pressing part 23 of an elastic deformation part 22A supports the rear end surface of the fallboard 1 at a forward position relative to the center O of its turning motion. ばね片22は拍子木21の後端面に固定され、弾性変形部22Aの押圧部部23が鍵盤蓋1の後端面で回動中心Oより前方位置を支持する。 - 特許庁
A triangular form and a support plate body are made on the leading top part by broad sense spring back, and when shock absorbing and breakaway method is taken by a locking latch or sensor motor-drive, a soft film is utilized to the full. 広義スプリングバックにより先導上部に三角形態や支持板体を造り、係止ラッチやセンサー電動によって、緩衝〜脱却法も計りつつ、軟性膜をフル活用する。 - 特許庁
The pad pressurizing means has a rotation support point so that the pad pressurizing means can be rotated forward and backward in the rotating direction of the pick roller around a connection part of the pad pressurizing means and the pressurizing spring. このパッド加圧手段と加圧バネの結合部を中心にパッド加圧手段がピックローラの回転方向に対して前後に回転可能なように、回転支点をもつように構成されている。 - 特許庁
To improve installation stability to a vehicle body, while hardening a spring characteristic in the horizontal direction of a rubber elastic body, for a strut mount installed in the vehicle body in an unfastened state. 車体に非締結状態で組み付けられるストラットマウントにおいて、ゴム弾性体の水平方向のばね特性を硬くしながら、車体への組み付け安定性を向上させる。 - 特許庁
The two fork parts 52 and 54 indicate the shape of each carrying arm 8 and 12 to be formed into each spring-operated curved shape 56 for absorbing impact load while being outwardly (inwardly) projected within a X-Y plane. 2本のフォーク部52、54がX−Y面内で外側(または内側)に凸状の衝撃吸収用のばね性湾曲形状56を持つ搬送アーム8、12を示している。 - 特許庁
The axial rotation of the connecting rod 30 is transferred to a connecting arm 16, and a pedal arm 12 is rotated around an arm supporting point 19 through the connecting arm 16 and a connecting spring 14. この連結ロッド30の軸回転が連結アーム16伝えられ、連結アーム16および連結バネ14を介してペダルアーム12がアーム支点19を中心に回動する。 - 特許庁
A damping member 90 damping the turning member 50 is fixed to the base 30 and it is adhered closely to an inner circumferential face 52b near an opening of the cup 52 by a ring like spring 92. 回動部材50を制動するダンピング部材90をベース30に固定してリング状バネ92によってカップ部52の開口近傍の内周面52bに密着させる。 - 特許庁
The lock weight 11 is formed of a forked hanging arm 19 with a pair of rocking shafts 18, a lock base 20 and a lock claw 21, and a spring bearing arm 22 projecting diagonally downward. ロック重り11は、一対の揺動軸18を備えた二又状の吊持アーム19と、ロックベース20およびロック爪21と、斜め下向きに突設されるばね受アーム22とで構成する。 - 特許庁
The spring-like part 66 is constituted from main protrusions 71 arranged in a compressed state between the motor shaft 34 and the lock holder 52, and sub-protrusions 72 arranged in a non-compressed state. そして、バネ状部66をモータ軸34とロックホルダ52との間に圧縮状態で配置されるメイン突起71と、非圧縮状態で配置されるサブ突起72とから構成した。 - 特許庁
To provide a contact which has a low and stable conducting resistance between a movable terminal and a fixed terminal and allows easy assembling of the movable terminal and a spring. 可動端子と固定端子との間の導通抵抗が小さくかつ安定しており、しかも可動端子及び付勢部材の組込み作業を容易に行うことができるコンタクトを提供する。 - 特許庁
To provide an apparatus for manufacturing an elastic material supporting member, in which deformation of a fitted rubber vibration isolator is small, and therefore a shift of a fitted position due to spring back of the rubber vibration isolator is also small. 嵌入された防振ゴムの変形が少なく、そのために防振ゴムの弾性復帰による嵌入位置のズレが小さいものとなる弾性材保持部材の製造装置を提供する。 - 特許庁
In compliance with insertion holes of the respective tumbler housing holes 104a and 104b for storage, the full tumbler 101 and a coil sprint 109, and the half tumbler 102 and a coil spring 115 are arranged. そして、収納すべき各タンブラ収納孔104a,104bの挿入口に対応して、フルタンブラ101とコイルバネ109、及びハーフタンブラ102とコイルバネ115を配置する。 - 特許庁
Further, by employing a strut type suspension, the arm ratio can be increased, and the diameter of a spring and the shock absorber can be suppressed small. またストラット方式のサスペンションを採用することによりアーム比を大きくできるので、アーム比を大きくすることができ、スプリングおよびショックアブソーバの直径を小さく抑えることが可能となる。 - 特許庁
When the plunger 11 is attracted, the end surface 163 of the stopper part 162 and the bottom surface 185 of the cap 18 are brought into contact to restrict movement of the second spring receiver 16 in the attraction direction side. プランジャ11吸着時に、ストッパ部162の端面163と、キャップ18の底面185とを当接させて第二のばね受け16の吸着方向側への移動を制限する。 - 特許庁
When the power source of the projector is turned on, the slide member is in the closing position, and when the power source is turned off, the slide member 252 slides to the open position with the energizing force of a spring part 2522. プロジェクタの電源がオンのときは、スライド部材252は閉塞位置にあり、電源がオフになるとばね部2522の付勢力によってスライド部材252が開放位置に移動する。 - 特許庁
An automatic electric connection mechanism 1 arranged in the vicinity of the air spring 5 is put in a condition in which positional relation of a connection part 10 on car body side and a connection part 20 on bogie side is substantially proper. 空気バネ5近傍に配置された自動電気連結機構1も、車体側連結部10と台車側連結部20との位置関係がほぼ適切な状態となる。 - 特許庁
A base part 77 is provided between left and right wall parts 74a and 74b at the rear end of the bottom surface part so as to be vertically movable via a spring, and the top surface part is turnably attached to the base part. 底面部の後端にある左右壁部74a,74b 間にはばねを介して上下動可能に基部77が設けられ、基部に天面部が回動可能に取り付けられる。 - 特許庁
Furthermore, by the fixed contacts 53g, 53l, 53h, and the flexible contact 53k formed protrudedly toward inside, a spring terminal 33 can be inserted easily, and can be held steadily after the insertion. また更に、内側に向けて張り出されて形成された固定接点53g、53l、53hと、可撓接点53kとにより、スプリング端子33を容易に挿着でき、挿着後には確実に保持できる。 - 特許庁
A slide bar spring 32 is arranged at one end of the slide bar 40, and a cam 24 and a drive motor 28 are connected to the other end of the slide bar 40, whereby the slide bar 40 is swung and driven. スライドバー40の一方端にはスライドバーバネ32が配置され、スライドバー40の他方端には、カム24と駆動モータ28が接続され、これにより、スライドバー40は揺動駆動される。 - 特許庁
Thus, it is possible to constitute the trigger dispenser 50 in a compact form and provide a significant degree of freedom in the dimensional change of the pump chamber 109, and further, obtain the required urging force while eliminating the necessity to perform the sorting/ disposal operation of the spring. これにより、コンパクト化を可能とすると同時に、ポンプ室の寸法変更などの自由度を大きくし、分別廃棄の必要をなくすと同時に、必要な付勢力を得る。 - 特許庁
An insertion bar 22 capable of being inserted into the cylinder of a filter holder and a spring member 23 capable of being freely attached to the insertion bar 22 are provided as a work retaining part 20 retaining the inside of the cylinder of the filter holder. フィルタホルダWの筒内を保持するワーク保持部20として、筒内に挿入可能な挿入バー22と、この挿入バー22に取付自在なバネ部材23を設ける。 - 特許庁
A coil spring 42 as a means of lightening for making the unbalanced load falling on the work by the rocker 20 light in weight, when the rocker 20 abuts on a work is arranged at the copying device 19. 揺動体20がワークに当接したときに、揺動体20によりワークにかかる偏荷重を軽減する軽減化手段としてのコイルスプリング42を倣い装置本体19に配置する。 - 特許庁
To provide an assembly body and an image recorder in which a spindle can be easily assembled to a frame while an expandable member such as a spring is passed through the spindle. 支軸にバネなどの伸縮性を有する部材が挿通された状態で、上記支軸をフレームに容易に組み付けることが可能な組立体及び画像記録装置を提供すること。 - 特許庁
A coil spring 75, externally fitted to a bolt erected on a horizontal bolt supporting piece 29, is mounted between the horizontal bolt supporting member 29 and a hold-down member 54 of a fastener 50 in a compressed condition. 水平ボルト受片29に立設されたボルト30に外嵌めしたコイルバネ75をその水平ボルト受片29と締付具50の抑え片54間に圧縮状に介装する。 - 特許庁