「Spring」を含む例文一覧(40241)

<前へ 1 2 .... 557 558 559 560 561 562 563 564 565 .... 804 805 次へ>
  • The curvature-correcting roller 26 is rotatable about an axis 26a, supported movably in vertical direction by the mover 20, and energized by a leaf spring 27 toward the card processing passage 6 side.
    反り矯正用のローラ26は、軸26aに回転自在で、軸26aを介して移動子20に上下動自在に支持され、板ばね27によってカード処理通路6側に付勢されている。 - 特許庁
  • The contact pressure spring 26 has a coil 260, and an end coil 261 extended inside from the upper end of the coil 260; and is provided by inserting a shaft 240 in a shaft 24 inside.
    この接圧ばね26は、コイル部260と、コイル部260の上端から内方に延設された座巻部261とを備え、シャフト24の軸部240を内部に挿通して設けられている。 - 特許庁
  • A sub-assembly member 20 for allowing the coiled spring 8 to be sub-assembled (temporarily installed and fixed) to the suspension cross member 10 before assembly of the vehicle body is arranged at the upper side of the suspension cross member 10.
    サスペンションクロスメンバー10の上方側には、コイルスプリング8を、車体組付け前にサスペンションクロスメンバー10にサブアッシー(仮組み固定)するサブアッシー部材20を設けている。 - 特許庁
  • A nonskid member 7 is attached on the inner side of the upper clamping part 3 and a leaf spring 11 in a chevron shape capable of bringing the peak part into press contact with the plate P is attached to the lower clamping part 4.
    上方挟持部3の内側には滑り止め部材7を取り付け、下方挟持部4には山形形状をしてその頂部を皿Pに圧接し得る板ばね11を取り付ける。 - 特許庁
  • A clocking plate in which a cutout part for fitting a bolt is formed and which is insertedly engaged between the base plate and the locking part so as to be held by the elastic force of the disk spring is made the female coupling.
    ボルトが嵌合される切欠部が形成され、ベース板と係止部との間に入り込んで係合し、皿バネの弾性力によって挟持される係止板を雌継手とする。 - 特許庁
  • A baffle plate 6 which is downward energized with a spring 63 and opposed to the discharging port 22 at the upper end of the filter body 2 is provided in a discharge chamber 5 which is successively provided at the upper end of the filter body 2.
    濾過体2の上端に連設される排出室5に、濾過体2の上端の吐出口22に対向する、ばね63で下方に付勢される邪魔板6を設ける。 - 特許庁
  • The wafer W placed on a table 12 is lifted together with the table 12 with extension of a bellows 16 and receives pressure by the pawls 21, while deforming the leaf spring members 22.
    載台12上に載置されたウェーハWはベローズ16の延伸により載台12とともに上昇し、板ばね部材22を変形させながら爪部21により押圧作用を受ける。 - 特許庁
  • An anti-come-off hole 15 is formed at the blade 11b to be engaged with a protrusion for preventing coming-off fitted to a blade-rest spring by rotating the plug housing after inserting it into the blade inlet.
    栓刃11bにはコンセントの栓刃差込口に挿入した後にプラグハウジングを回転させることによって刃受ばねに設けた抜止用の突起に係合する抜止孔15が形成される。 - 特許庁
  • The moving member 20 to which a stage 21 is fixed and the movable member 30 are pressed in a direction that they are energized in mutually separating direction by a compression coil spring 31 with which the movable member 30 is provided.
    ステージ21が固着された移動部材20と可動部材30とは可動部材30に設けられた圧縮コイルばね31によって互いに離れる方向へ付勢されている。 - 特許庁
  • When the force as the paper feed roller 34 willing to run by itself on the sheet P and the energizing force of the spring 37 become even, the supporting member 33 stops swinging, and the sheet P is transported.
    給紙ローラ34が記録紙P上を自走しようとする力と引きバネ37の付勢力とが拮抗すると支持部材33の揺動が停止し、記録紙Pが搬送される。 - 特許庁
  • The center hinge 17 is attached with a torsion spring 30 for energizing the lower door 16 so that the upper door 15 and the lower door 16 are folded up from a state of being arranged in a plate shape.
    センタヒンジ17には、アッパドア15及びロアドア16が板状に配置された状態から折り畳むようにロアドア16を付勢するトーションスプリング30が装着されている。 - 特許庁
  • The rotary drive member 14 is energized to the push-press drive member 8 side by a coned disk spring 24 and on the push- press drive member 8 and rotary drive member 14, engagingly locking teeth 80, 140 are formed on a mutually facing surface.
    回転駆動部材は、皿バネ24によって押圧駆動部材側に付勢されており、押圧駆動部材と回転駆動部材とには、向かい合った面に係止歯80,140が形成されている。 - 特許庁
  • To constitute a brush unit in such a manner as not only the brush unit is applied to the external terminal of a short length, but also no problem is caused in insertion of the external terminal, while securing enough spring-like force in a receptacle terminal.
    リセプタクル端子に十分なバネ性を確保しつつ、長さの短い外部端子に適用可能にするだけでなく、外部端子の挿入性問題が生じない構成にする。 - 特許庁
  • To solve the problem of a silencing effect being reduced if the constant of a coil spring is reduced to reduce a force in a closing direction, since then a control valve opens from the low revolution of an internal combustion engine.
    コイルバネの定数を低下させ閉鎖方向の力を減らそうとすると、内燃機関の低回転時から制御弁が開いてしまうため、消音効果が低下してしまう。 - 特許庁
  • A first enclosing container 80 in which a demarcation member 50, a coil spring 65 as a pulverization preventive member and granular gas generating agent 62 are stored therein is arranged in the working gas production chamber.
    作動ガス生成室には、区画部材50、破砕防止部材としてのコイルバネ65および粒状のガス発生剤62が内部に収容された第1密閉容器80が配置されている。 - 特許庁
  • A cantilevered earth spring 21 electrically connecting a support member supporting a spindle motor and a casing, has a free-end made in a circular-arc shape and a bent structure at the tip end 26.
    スピンドルモータを支持する支持部材部と筺体部とを電気的に接続する片持ち構造のアーススプリング21であり、自由端を円弧形状とし、さらに先端部26に曲げ構造を備えた。 - 特許庁
  • The locking releasing mechanism includes: an engagement claw 81 provided on the dial 8; an engagement pin 92 provided on the slide member 9; and a spring member 15 for biasing the dial 8 in the return direction.
    さらに、ロック解除機構は、ダイアル8に設けた係合爪81と、スライド部材9に設けた係合ピン92と、ダイアル8を戻し方向に付勢するバネ部材15とからなる。 - 特許庁
  • To provide a technique concerning a hydraulic cylinder apparatus which reinforces a starting force on a drawing side for working on a load such as a metallic mold, by a restoring force of an elastic body like a belleville spring.
    皿バネなどの弾性体の復元力により、金型などの負荷に作用させる引き側の開始時の力を増強するようにした液圧シリンダ装置に関する技術である。 - 特許庁
  • A diameter expanded part 51 which can be displaced on a restriction part 12a side is disposed to a small diameter part 39b of the spring receiving member 39, and an O-ring 57 is disposed to an outer periphery of the diameter expanded part 51.
    バネ受け部材39の小径部39bには、規制部12a側へ変位可能な径拡張部51が設けられ、径拡張部51の外周にはOリング57が設けられている。 - 特許庁
  • To increase durability without occurrence of distortion at an elastic body having a thin wall between a mounted face and a mounting hole even if a high spring constant in an orthogonal direction is given.
    取付面と直交する方向でのバネ定数を高めても被取付面と取付孔との間の肉厚が薄い弾性体の部分に歪が発生せず、耐久性を向上させる。 - 特許庁
  • To prepare a skin lotion for bleaching, having excellent skin bleaching effect, giving non-sticking refreshing feeling to the skin and most suitable for the use especially in spring and summer seasons having increased demand.
    美白効果に優れ、かつべたつきがなくさっぱりとした使用感を有し、特に需要の大きい春から夏にかけて使用するのに最適な美白用皮膚外用剤を提供する。 - 特許庁
  • To provide a rotating electrical component which is capable of preventing click torque from increasing, while a rotary torque is restrained from increasing by elastically pressing a leaf spring against a case side to surely make feeling of clicking clear, when the part is rotated.
    本発明の回転型電気部品は、板バネがケース側に弾圧することで、回転トルクの上昇を抑えつつ、クリックトルクの上昇を図り、クリック感を明確にすること。 - 特許庁
  • The contact part 10a of the coil contact spring 10 and a coil terminal 6a of the exciting coil 6 extended around from the diaphragm 9 are soldered and connected by using solder 12.
    一対の半田付け端子11に、コイル接点バネ10の接点部10aと、振動板9から回し込んだ励磁コイル6のコイル端末6aとを半田12で半田付けして接続する。 - 特許庁
  • Then, time until the operation position of the drive shaft 1 reaches a return operation completion position θSR from turn-off of the electromagnetic clutch 4 is automatically measured as spring return operation time TS.
    この時、電磁クラッチ4が断とされてから駆動軸1の動作位置がリターン動作終点位置θSRへ到達するまでの時間を、スプリングリターン動作時間TSとして自動計測する。 - 特許庁
  • The fuel adjustment valve is a diaphragm type which is sealed by the pressure by a spring disposed in a reference chamber which is formed between a housing and a side surface of a diaphragm, and communicated with the atmosphere.
    該燃料調整バルブは、ハウジングとダイアフラムの側面の間に形成され、大気に通気された基準室内に配置されたバネにより予圧で封止されたダイアフラム型である。 - 特許庁
  • A valve element 16 to be attached/detached to/from the valve seat 19 from the hydrogen tank 2 side in the communication passage 13 is provided, and the valve element 16 is urged in the direction of the valve seat 19 by a spring 20.
    弁座19に対して、連通路13内の水素タンク2側から離接する弁体16を設け、弁体16をスプリング20によって弁座19方向に付勢する。 - 特許庁
  • In winter, spring, and autumn, temperature of service water is lower than 20°C so that a control section 8 controls power supply to the heater 4 such that temperature detected by a hot water temperature thermistor 5 becomes 40°C.
    冬、春及び秋にあっては、水道水の温度が20℃未満であるので、制御部8は湯温サーミスタ5で検出される温度が40℃となるようにヒータ4への通電を制御する。 - 特許庁
  • Even when the movable molds 22 and 24 are returned in the direction where they approach together again under a condition where ejector pins 28 push up a pulley 10, the movable molds 22 and 24 can not be returned by energizing force of the spring 30.
    イジェクタピン28がプーリ10を押し上げている状態で可動金型同志が再び接近する方向へ戻ろうしても、スプリングの付勢力によって可動金型は戻らない。 - 特許庁
  • These right and left spring bearing 21 and 22 are provided with stoppers 23, 24, and 25 to stop the tilt of a backrest 4 in such a way that the bush 9 inserted into the slot 7 blocks the movement of the slide shaft 8.
    左右ばね受け21,22 には、長穴7にブッシュ9に嵌入してスライド軸8の移動を阻止することによって背もたれ4の傾動を阻止するストッパー23,24,25が装着されている。 - 特許庁
  • The movable side rack 42 is pressed in a Q direction by a plate spring 41c formed in the holding plate 41, thereby reducing backlashing of the engagement between the pinion gear 51 and the rack member.
    可動側ラック42は、保持板41に形成された板ばね41cでQ方向へ付勢され、ピニオン歯車51とラック部材との噛み合わせのバックラッシュが低減されている。 - 特許庁
  • Between the contact glass 7 and the press plate 8, a depression force is exerted on the press plate 8 through a spring 9 to slide the cleaning part 18 pressed to the contact glass 7 and the press plate 8.
    コンタクトガラス7と圧板8間では、圧板8に対してスプリング9により下圧力が加えられており、クリーニング部18がコンタクトガラス7と圧板8とに圧接した状態で摺動する。 - 特許庁
  • When trouble such as breakage occurs in the motor 30, a current is supplied to an electromagnetic drive portion of the spool valve 60 for attaching the spool valve member 61 against the energizing force of the spring 62.
    モータ30に断線等の故障が発生すると、スプール弁60の電磁駆動部に電流を供給し、スプリング62の付勢力に抗しスプール弁部材61が吸引される。 - 特許庁
  • The reservoir tank 61 is also connected to a pressure chamber 43 of a valve opening air spring 40 through a supply passage 63 and a communicating hole 44 formed in a cylinder 41.
    またリザーバタンク61は、供給通路63及び上記シリンダ41に形成された連通孔44を通じて、開弁用空気ばね40の圧力室43に連結されている。 - 特許庁
  • To provide an arm device to be made thin, wherein the unnecessary twisting of an arm is reduced by increasing the rigidity to twisting of a thin plate spring for supporting the arm fixing a magnetic head.
    磁気ヘッドを固定したアームを支持する薄板バネの、ねじれに対する剛性を向上させて、アームの不要なねじれを低減した薄型化可能なアーム装置を提供する。 - 特許庁
  • A contact open/close mechanism 11 comprises: a handlebar 12 that is operated by a user; a leading component 13 for driving a movable contact 8; and a spring 14 that urges the leading component 13 upwardly.
    接点開閉機構11は、ユーザーが操作するハンドル12と、可動接点8を駆動する引外し部材13と、引外し部材13を上方へ付勢するスプリング14とからなっている。 - 特許庁
  • A gas spring is located in the housing, retracts during loading dry wall compound into the chamber and discharges the compound when the discharge nozzle is opened by the pull rod.
    ガススプリングがハウジングの中に配置され、チャンバーの中にドライ壁化合物を充填する際には収縮し、また、引棒によって放出ノズルが開放されると化合物を放出する。 - 特許庁
  • When the guide pin 12 reaches an upper end of oblong hole 11, the gas spring 14 is not expanded any more, and the seat part 4 is inclined forward at the downward gradient.
    ガイドピン12が長孔11の上端までくると、ガススプリング14はそれ以上伸長しないので、流体圧シリンダ13の伸長により、座部4は前方に向かって下り勾配で傾斜する。 - 特許庁
  • To provide an elastic support body for a structure capable of adjusting spring constant of a horizontal load supporting part and/or a vertical load supporting part and having small plane dimension of support.
    水平荷重支持部および/または鉛直荷重支持部のばね定数を調節することができ、支承の平面寸法が小さい構造物用弾性支承体を提供する。 - 特許庁
  • In the process cartridge 13, a leaf spring 23 energizes the developing cartridge 16 backward, whereby the developing roller 33 comes into contact with the photoreceptor drum 18 in a pressing state.
    プロセスカートリッジ13において、板ばね23が現像カートリッジ16を後方に向けて付勢することにより、現像ローラ33が感光ドラム18に対して押圧状態で接触する。 - 特許庁
  • The opposed (load) side open end of the frame 6 and a bracket B5 are engaged with each other so that the outer ring of a ball bearing 8 and a wave-form spring 10 abut on each other in the housing of the bracket B5.
    さらに、フレーム6の反対(負荷)側開口端部とブラケットB5を、玉軸受8の外輪と波形バネ10とがブラケットB5のハウジング内で当接するように嵌合する。 - 特許庁
  • Since the blade receiving member 30 is integral with the terminal part 40 and the grade receiving part 31, no conventional locking spring is required, resulting in less number of components for cost reduction.
    このように端子部40と刃受部31を一体として刃受部材30を構成しているから、従来の鎖錠ばねが不要となり部品点数の削減によってコストダウンが図れる。 - 特許庁
  • A flange 41 projectingly formed is integrally provided on the lower outside surface of the pentagonal mirror 4, and the top end part of a pressing spring 201 attached to the camera main body abuts on the flange 41.
    ペンタミラー4の下部外側表面に一体に突出形成されたフランジ41を設け、カメラ本体に取り付けられた付勢バネ201の先端部を前記フランジ41に当接させる。 - 特許庁
  • Before fastening a U bolt for attaching the leaf spring in the state that the axle member is placed on the working base, a pin penetrating attachment holes of right and left leaf springs to a vehicle body is inserted.
    アクスル部材を作業台に載置した状態で、リーフ・スプリング取付けのためのUボルトを締付ける前に、左右のリーフ・スプリングの車体への取付け孔を共に貫通するピンを挿通する。 - 特許庁
  • To enable a lifting and housing operation of a marker 30 by a marker-operating structure to be carried out lightly in a marker device having a lowering urging spring 43 for urging the marker 30 to the lowered using posture.
    マーカ30を下降使用姿勢に付勢する下降付勢スプリング43を備えたマーカ装置において、マーカ操作機構によるマーカ30の上昇格納操作を軽くできるようにする。 - 特許庁
  • The switch 14 includes a resilient metal wire 17 which deforms resiliently to touch the resilient coil portion 13C of the spring wire 13, and an insulated insert/withdraw member 18 for pressing the resilient metal wire 17.
    スイッチ14は、弾性変形してスプリング線13の弾性コイル部13Cに接触する弾性金属線17と、弾性金属線17を押圧する絶縁出入具18とを備える。 - 特許庁
  • To improve a situation that a spring for biasing a barrier blade in a closing direction easily falls in a lens barrier device, which has an adverse effect on the improvement of assembly workability of the lens barrier device.
    レンズバリヤ装置においてバリヤ羽根を閉じ方向に付勢するバネが脱落し易いためレンズバリヤ装置の組付作業性の向上に悪影響を与えていたのを改善する。 - 特許庁
  • As a result, when the pad press-down piece 14g and the ear piece 6c are resiliently contacted close to a caliper center line CL, elastic force operating from a spring section 14c to a friction pad 6 is small.
    これにより、パッド抑え片14gと耳片6cとがキャリパ中心線CL寄りで弾接する場合には、スプリング部14cから摩擦パッド6に作用する弾発力が小さい。 - 特許庁
  • When the ladder main body 1 reaches a lower limited position and an upper limited position respectively, the interlocking holder 14 is elastically interlocked with both upper and lower interlocking devices 12 and 13 by a spring 17.
    ラダー本体1がそれぞれ下限位置、上限位置に達するとスプリング17により係止受具14が上係止具12、下係止具13に弾発的に係止される。 - 特許庁
  • On the side with a group 29A of ring-shaped thin plates, the leaf seal 25 is furnished in a single piece with a leaf spring 56 to support them in the levitated condition in such a way as coaxial with a rotary shaft 23.
    また、環状の薄板群29A側に、これらを回転軸23と同軸をなすよう浮上状態に支持する板バネ56を一体に設けたリーフシール25を採用した。 - 特許庁
  • Thus, when one electronic unit is extracted, the wind leakage preventing plate 4 is pushed out by the repulsion force of the spring 5 of the opposite side to shut off wind leakage from the insertion opening 11.
    これにより一つの電子ユニットを抜き出すと、反対側のスプリング5の反発力で風漏れ防止板4が押し出され挿入開口部11からの風漏れを遮断する。 - 特許庁
<前へ 1 2 .... 557 558 559 560 561 562 563 564 565 .... 804 805 次へ>

例文データの著作権について

  • 特許庁
    Copyright © Japan Patent office. All Rights Reserved.